Fiberglass duct rodder & snake duct rodder & electric rodder & fiberglass duct rod & duct rodder cable & conduit rodder & cable rodder & push pull rod description: Duct rodder applies in tow lead-rope through a pipe,it is auxiliary means. Surface smooth and high resilience,so the FRP perforator with ease passes the narrow channel. perforator consists of two parts: the glass fiber strengthen the level, the high-pressured low density polyethylene protective layer(smooth, firm ,can resist the adverse circumstance). It has time-savingreducing effort, improving efficiency, etc,And can be used for telecom cables, cable pipe and cleaning and plastic pipe of cloths to put.when use draws out the FPR pole by the pulley, then with a corresponding metal joint, penetrates in the pipeline. When cleaning, guide-head will drive cleaning tools to clean the pipe;When arranges the cable,you may first leads the steel wire or the iron wire, then enters the pipe with the steel wire or the iron wire hauling cable. Fiberglass duct rodder technical specifications: Glass fiber rod diameter 4.5-16mm Length 1-500m Working temperature -40+80 Min Bend Radius 295mm Breaking tension 4.5T Glassfiber density 150g/m 1.constructed of fiberglass reinforced in the center and consists of a rugged plastic layer that would ensure the lifetime of the flexible rod. 2.Excellent flexibility force. 3.Tensile strength about 500 Kgf. 4.designed for heavy duty applications ensuring greater rigidity and strength, while supporting additional forces without resentment to the multiple curvatures. 5.Wheel assembly for easy transportation. 6.Guide rollers and the right parts for rotary coupling. 7.Rolling bearing cage flotation (reel transport) for mobility should be light and easy to use in the field, including a parking brake for the flexible rod. 8. There is copper wire inside for tracing easily. Technical data of duct rodders 1. Glass reinforced composite core: general properties Property value keinforcement E-glass fiber glass content of inner part 75-80% material of pulling rod epoxy fiber glass(inner) high density polyethylene(outer) density >1.9gr/cm3 diameter tolerance +/-0.10mm work situation temperature -40 to +80 Mechanical prperties property value minimum pullling strength 4000 N+/-5% tensile modulus >30000Mpa consistency of rod 150gr/m +/-5% flexural modulus >30000M pa elongation at break 2.5-3% 2. Polyethylene cover Material: Medium density polyethylene resin for the insulating and jacketing of telecommunications cables. property value tensile strength >15N/mm2 environmental stress & crack resistance >1000 hr. heat stability OK. carbon black OK. packed by plastic woven, or wooden pallet. Length 0.5-1.5m Width 0.15-0.5m Height 0.5-1.5m
Frp profile/fiberglass products.
Fiberglass grating.
Unidirectional Biaxial mat triaxial mat, multiaxial mat can be designed and produced. It is used widely in hand lay up, RTM, filament winding, wind blade and so on composite FRP products. Area weight from 300g/m2 to 1200g/m2.
Frp gratings, frp doors, frp pipe ,frp tanks, frp manhole covers, frp drainage cover, frp bus body parts , frp blower , frp motor cover , frp switch box , frp planters, frp cable tray , frp barriers, frp mannequin, frp seating garden table , frp sheets , customize frp products , etc..
Quality guarantee: 1.Two-year limited guarantee 2.Highest quality manufacturing standards (iso9001) 3.Wide range of temperature tolerance (-20¡æ¡§d65¡æ) 4.High salt fog, dust and sand resistance 5.Strong wind resistance and high survival wind speed 6.Durable materials and components(i.E. Sweden's skf bearing) Easy transportation and installation: 1.Light and compact size 2.Intuitive online installation guides 3.Wide installation and maintenance network worldwide 4.Perfect after-sales service system Dimensions Technical specifications¡êo Model Airforce 4.1 Rated output power 5 kw Max. Output power 5.1 kw Rated wind speed Grid-tied 380vdc / off-grid 48vdc Max. Wind speed 12 m/s Survival wind speed 20 m/s Start-up wind speed 60 m/s Cut-in wind speed 1.5 m/s Rated rotational speed 2 m/s Max. Rotational speed 390 rpm No. Of blades 455 rpm Rated output power 3 Rotor diameter 4.1 m Blade length 2.02 m Blade material Frp Generator 3 phases pm generator Braking system Electromagnetic braking control system Type Downwind rotor Yaw control Passive Total weight 120 kg Warranty Whole system-2 years Controller Full-automatic control Tower 12 m(optional) Power curve¡êo Totla weight¡êo188 kg Generator¡êo73cm*60cm*53cm 0.232cbm Blades¡êo210cm*55cm*56cm 0.646cbm
as main equipment in the production line, it's designed for the GRP pipe manufacturing. Mechanism constitution and its working principle are Stating as follows: It mainly consists of mandrel driving device, overall frame, steel Band pusher, beam cam disc, band circulating head, band exit head, beam for Band supporting, steel band, liner chopper devices for liner and structure, sand Feeding device, chopped roving shelf for liner and structure, hoop roving shelf for liner and structure, Resin mixing and spraying devices for liner and structure, infrared heating System, mylar winder, surface veil winder, external layer winder, pneumatic Rollers for liner and structure, finishing pneumatic roller, Hydraulic lifting Table, online cutting & grinding device, dust collector, PLC control System, electrical control system, etc. the main transmission of the winding machine is assembled with mould Consisting of cam disc, band exit head, band circulating head, beams for band Supporting and closed-loop steel band. Once the mould rotates with the transmission, steel band winds on the beams distributed around the circle of cam disc and moves in the axial way under the impetus of pushers. Band will be pushed forward at one band width with every complete revolution of the mandrel. When it arrives the rear end of the beam, steel band will be LED into mandrel's hallow tube via exit head and Circulating head, and then return to the very starting point. In this way, Steel band forms a circulation process of winding, pushing forward, leading Out, leading in and rewinding. Wind the mylar and surface veil onto the band as it forms the Winding cyclic movement. And, simultaneously, onto the band, spray resin through spraying device for liner layer and structure upward side, spread Chopped roving via chopper devices for liner layer and structural layer, feed Sand by sand feeding device, and wind hoop roving from the roving shelf. after the hoop roving, chopper, resin and sand on the band are completely mixed and Impregnated with the effect of pneumatic roller, it moves forward with band in the axial way into the infrared heating area to be cured and then moves on Until leave the band mould. Hydraulic lift table will rise sequentially and the Rollers on the table support the cured pipe. Pipe will be cut after it reaches A certain length and both ends are trimmed by online cutting and trimming Devices. In this way, the production of a pipe is done. The amount of chopped Roving for liner layer and structural layer, hoop roving, sand as well as resin Are preset and controlled by PLC which also controls the temperature of resin And sand.
GRP Pipe Filament Winding Prodcution Line-Winding Machine GRP Pipe Winding Machine Specifications: General technical data: Diameter range DN300mm-3000mm Length of Product 12m Winding Angle 45° - 90° Carriage stroke 13m Control Manner Two axes motion and three spindles Electrical power supply 380V, 3 phases 50-60 Hz Raw materials: Resin Polyester resin, or vinyl ester resin with reinforcement yarn E-Glass or ECR Roving 1. Liner making machine(13 Kw/set) (1set) Consist of: 1) Headstock 1 set 2) Tailstock 1 set 3) Railway 1 set 4) Carriage 1 set 5) Four-wheel pneumatic roller 1 set 6) Mylar delivery rack 1 set 7) System of timing with frequency conversion 1 set 8) Electric control system 1 set 9) Resin feeding system 1 set
Fiberglass filament fabric is a kind of engineering materials. With non-combustible, corrosion-resistance, high temperature, low temperature absorption, deformation coefficient of small fine features, this new material has been covered electrical products, electronics, transportation, chemical engineering, construction, acoustic insulation, fire and environmental protection and other fields. E-glass (alkali c-glass) glass fabric have a tube of fabric and flat fabric hours: a woven fabric casing pipe, rope, hairdryer cloth, filter cloth in the main cylinder; plane fabric by width can be with glass fiber is divided into the following 100mm, 100-300mm narrow fabrics below and above the ordinary 300mm width of fabric; flat woven fabrics according to side can also be divided into edge and non-woven texture of the two edges. There are shuttle loom weaving machine and weft woven into a continuous weaving of that there is even (with selvage) fabric, commonly known as the light side of the fabric. Shuttleless loom weaving, the weft cut off from the edge of cloth known as non-woven side (without selvage) fabric, commonly known as the fabric edges. Glass fiber woven fabric according to the existing methods can be divided into woven fabric, knitted fabric, knitted fabric and sewing the four basic types of fabrics. Standard carton box
We are a leading exporter/mfr of fiberglass and concrete planters, flowerpots, fountains in china. Our products can be with different style, such as painting smooth finish (glossy or matte), slate finish, rattan finish, concrete finish, antique finish, copper finish, translucent, etc. And we can produce it as your own design. Our products have been widely accepting in the world market since 2001. Our quality is no 1-3 in china. Our long experience and high professional service and high quality are our most competitive Carton
Our range of Fiberglass Tape is made of E-Glass yarn. 1) Good thermal resistance 2) Excellent insulating 3) Good corrosion resistance Applications: Fiberglass Tape can be widely used as wrapping and banding material for transformers, electric motors and cables. Specifications: Thickness(mm) Width(mm) Length per Roll(M) 0.1mm, 0.13mm, 0.15mm, 0.20mm etc 10mm, 15mm, 20mm,25mm,30mm etc 50M/100M Etc. It could be packed with cartons. 50M per rool, 100m per roll.
Coated alkaline resistent fiberglass mesh specs Mesh size: 5mm*5mm; Area weight: from 80 to 160g/m2; Width: 1m; Color: white, blue, yellow, red, etc. Film, carton, pallet
"DD fiberglass" Fiberglass chopped strand mat Glass type: e-glass, c-glass; Area weight: 150, 225, 300, 450, 600g/m2; Width: 1040mm, 1250mm. Binder: powder, emulsion. Film, carton
Coated alkaline resistent fiberglass mesh Fiberglass mesh specs: Mesh size: 4mm*4mm; 5mm*5mm; 10mm*10mm; Area weight: between 80 to 160g/m2; Width: 1m; Roll length: 50m; Color: white, blue; Other specs are also available. Film, carton, pallet
Fiberglass Rope Description: 1. Fiberglass Rope Gasket is made of continuous filament texturized C or E glass yarns, and glass fiber rope is extremely strong, resilient, and flexible. 2. Fiberglass Rope Gasket are asbestos free, cause no harm to health, making them ideal replacements to asbestos ones. 3. For higher loads, the round braided and square braided ropes can be reinforced by steel wires. 4. Fiberglass Rope Gasket also can be coated with graphite or vermiculite to increase thermal insulation and abrasive resistance. Fiberglass Rope Application: 1. Glass Fiber Round Rope are widely used as gasket for industrial ovens and furnaces, boilers and wood burning stoves.
Cemfil-arg-roving-fiberglass.
Fiberglass mesh Features: 1) applications: A) widely used for strengthening architectural structures and walls with good performance as reinforcing steel bar B) used in spreading layer, daubing and mechanical molding grc C) also used heat preservation work outside wall in local constructing D) can be put up as shield in agriculture to resist pest 2) we can supply styles of products according to users' needs Each roll should be wound onto a paper tube and then Wrapped up with plastic film, which should be packed in a cardboard Box, the rolls are to be horizontally placed. Rolls can be loaded into a container directly or pallets.
Chopped strand Fiberglass chopped strand Chopped strand products are used as reinforcement in the thermoplastic such as engineering plastics and in thermosetting resins, such as polyester and phenol resin. Thermoplastics are used a wide range of industries, including the automotive, electrical and electronics industries. Also it is easy to control the cost and is the most ideal choice of the current constructional fibers.
300/450/600/225 gsm powder/emulsion binder Woven roving 400/600/800gsm Direct roving 1200/2400/4800tex Fiberglass mesh Chopped strands for smc/bmc 3/4/6/12mm. According to customer requriement
Fiberglass Lagging Rope Description: 1. Fiberglass Lagging Rope is made of continuous filament texturized C or E glass yarns, and glass fiber rope is extremely strong, resilient, and flexible. 2. Fiberglass Lagging Rope are asbe stos free, cause no harm to health, making them ideal replacements to asbe stos ones. 3. For higher loads, the round braided and square braided ropes can be reinforced by steel wires. 4. Fiberglass Lagging Rope can also be coated with graphite or vermiculite to increase thermal insulation and abrasive resistance. Fiberglass Lagging Rope pplication: 1. Fiberglass Rope are widely used as gasket for industrial ovens and furnaces, boilers and wood burning stoves.
