Roots Blower, Submersible Roots Blower, Magnetic Drive Pump, Vacuum Pump, Diffuser.
Appropriate for pumping clear water or lightly contaminated water. Used to flood to flood control and drainage farmland irrigation, water supply projects, etc. Power: 22 to 500 kw Discharge: 500 to 20000 m3/h Head: 1.5 to 15 m (3.6- 54 feet) Pump outlet diameter: 350 to 1400mm (13.7 to 55.1 inch) Dia. Of impeller: 267 to 1540mm (10.5 to 60.6 inch) Rotate speed: 485 to 1450 r/min Angle of impeller installation: from -6 deg. To +6 deg. Ph value: 6, 9 Operating limits: Maximum ambient temperature 50 deg. C Motor: 1. Rewindable, dry-type, whole sealing and three-phase asynchronous motor 2. Insulation grade: f 3. Protection grade: ip68 4. Double/triple mechanical sealing 5. Equipped with special control cabinet 6. Voltage: 380-10000v 7. Frequency: 50; 60hz Materials: 1. Pump body: cast iron 2. Impeller: stainless steel 3. Shaft with rotor: 45 steel Advantages: 1)the integration of pump body and motor without other assembly process 2)saving price 30 to 40% comparing with the ground sewage pump station with the civil and structural engineering. 3)lower noise and underground pump station. 4)easy, reliable and steady operation, realizing remote control. 5)greater weight for same bulk 6)completely meeting power standard by testing
Appropriate for pumping clear water or lightly contaminated water. Used to flood to flood control and drainage farmland irrigation, water supply projects, etc. Power: 22 to 500 kw Discharge: 500 to 20000 m3/h Head: 1.5 to 15 m (3.6- 54 feet) Pump outlet diameter: 350 to 1400mm (13.7 to 55.1 inch) Dia. Of impeller: 267 to 1540mm (10.5 to 60.6 inch) Rotate speed: 485 to 1450 r/min Angle of impeller installation: from -6 deg. To +6 deg. Ph value: 6, 9 Operating limits: Maximum ambient temperature 50 deg. C Motor: 1. Rewindable, dry-type, whole sealing and three-phase asynchronous motor 2. Insulation grade: f 3. Protection grade: ip68 4. Double/triple mechanical sealing 5. Equipped with special control cabinet 6. Voltage: 380-10000v 7. Frequency: 50; 60hz Materials: 1. Pump body: cast iron 2. Impeller: stainless steel 3. Shaft with rotor: 45 steel Advantages: 1)the integration of pump body and motor without other assembly process 2)saving price 30 to 40% comparing with the ground sewage pump station with the civil and structural engineering. 3)lower noise and underground pump station. 4)easy, reliable and steady operation, realizing remote control. 5)greater weight for same bulk 6)completely meeting power standard by testing
Appropriate for pumping clear water or lightly contaminated water. Used to flood to flood control and drainage farmland irrigation, water supply projects, etc. Power: 22 to 500 kw Discharge: 500 to 20000 m3/h Head: 1.5 to 15 m (3.6- 54 feet) Pump outlet diameter: 350 to 1400mm (13.7 to 55.1 inch) Dia. Of impeller: 267 to 1540mm (10.5 to 60.6 inch) Rotate speed: 485 to 1450 r/min Angle of impeller installation: from -6 deg. To +6 deg. Ph value: 6, 9 Operating limits: Maximum ambient temperature 50 deg. C Motor: 1. Rewindable, dry-type, whole sealing and three-phase asynchronous motor 2. Insulation grade: f 3. Protection grade: ip68 4. Double/triple mechanical sealing 5. Equipped with special control cabinet 6. Voltage: 380-10000v 7. Frequency: 50; 60hz Materials: 1. Pump body: cast iron 2. Impeller: stainless steel 3. Shaft with rotor: 45 steel Advantages: 1)the integration of pump body and motor without other assembly process 2)saving price 30 to 40% comparing with the ground sewage pump station with the civil and structural engineering. 3)lower noise and underground pump station. 4)easy, reliable and steady operation, realizing remote control. 5)greater weight for same bulk 6)completely meeting power standard by testing
MDG Boiler Feed Water Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc. MDG Boiler Feed Water Pump Introduction: MDG Boiler Feed Water Pump can deliver clear water without solid particles or other liquid which the physical and chemical feature is similar with clear water. The boiler hot water circulating pump is suitable for boiler feed water or feed water of high-pressure boiler. The temperature range of liquid is from -20 ¡ãC to -150 ¡ãC and the inlet pressure of pump is less than 0.6 Mpa. MDG Boiler Feed Water Pump Features: 1) Stator parts of the MDG boiler feed water pump : It mainly consists of suction stage, mid-stage, discharge stage and diffuser; they are strained through a lever and form a working chamber. the inlet and the outlet are vertival upword. 2) Rotor parts of the MDG boiler feed water pump : It mainly consists of shaft, impeller, balance kettle and shaft sleeve. Shaft transfers power to impeller and make the pump work. The axial force is balanced by balance disc (kettle) and there is rechargeable shaft sleeve in shaft to protect shaft. 3) Bearing parts of the MDG boiler feed water pump: It mainly consists of bearing body, shaft cover and sliding bearing. There are two single centripetal ball bearing in bearing body to prevent balance disc (kettle) from abrasion. The sliding bearing is lubricated by dilute oil, there is cooling chamber in bearing body and the bearing can be cooled with exterior water. 4) Shaft seal parts of the MDG boiler feed water pump : Shaft seal uses soft packing seal. It mainly consists od seal box, packing, packing ring and packing cover. The shaft is sealed, cooled and lubricated by exterior water from seal chamber. The mechanical seal can also be used as requirement and it need be cooled, lubricated and washed by exterior water. 5) Drive: Type MDG boiler feed water pump is directly driven by motor through flexible coupling. View from motor end, the rotating direction of pump is clockwise. MDG Boiler Feed Water Pump Parameter Selection Table: Model Speed(r/min) Flow Head(m) Power(KW) NPSH (m) m3/h L/S Shaftpower Motorpower MDG6-25×3 2950 3.75 1.04 76.5 2.37 5.5 2.0 6.3 1.75 75 2.86 2.0 7.5 2.08 73.5 3.19 2.5 MDG6-25×4 2950 3.75 1.04 102 3.16 7.5 2.0 6.3 1.75 100 3.81 2.0 7.5 2.08 98 4.26 2.5 MDG6-25×5 2950 3.75 1.04 127.5 3.95 7.5 2.0 6.3 1.75 125 4.77 2.0 7.5 2.08 122.5 5.32 2.5 MDG6-25×6 2950 3.75 1.04 153 4.73 11 2.0 6.3 1.75 150 5.72 2.0 7.5 2.08 147 6.39 2.5 MDG6-25×7 2950 3.75 1.04 178.5 5.52 11 2.0 6.3 1.75 175 6.67 2.0 7.5 2.08 171.5 7.45 2.5 MDG6-25×8 2950 3.75 1.04 204 6.31 15 2.0 6.3 1.75 200 7.63 2.0 7.5 2.08 196 8.58 2.5 MDG6-25×9 2950 3.75 1.04 229.5 7.10 15 2.0 6.3 1.75 225 8.52 2.0 7.5 2.08 220.5 9058 2.5 MDG6-25×10 2950 3.75 1.04 255 7.89 18.5 2.0 6.3 1.75 250 9.53 2.0 7.5 2.08 245 10.63 2.5 MDG6-25×11 2950 3.75 1.04 280.5 8.68 18.5 2.0 6.3 1.75 275 10.5 2.0 7.5 2.08 269.5 11.71 2.5 MDG6-25×12 2950 3.75 1.04 306 9.47 18.5 2.0 6.3 1.75 300 11.44 2.0 7.5 2.08 294 12.78 2.5 MDG Boiler Feed Water Pump Application: This series boiler feed water pump is used for transport no solid particles contained water or Chemical and Physics water Boiler feed water and boiler circulation water High-rise building booster Urban Fire booster Long distance water transportation Boiler heating and cooling water circulation booster
SEAL OIL PUMP,AC DRIVEN HSNH660-40NZ is an exclusive product for power units offered by Yoyik. Dongfang Yoyik Engineering Co., Ltd mainly provides hydraulic components, spare parts of power units, mechanical parts processing and so on. We have spare parts, components, replacements for generators, boiler, turbines and hydroturbines. SEAL OIL PUMP,AC DRIVEN HSNH660-40NZ converter A/D DZXL-ZL-E-6682 O-RING 315X3.55 Dacron glass fiber strip Ï?2 stator slot wedge 4Q9189 Filter QTL-250 generator grease gun KH-35 grease gun 3.463.338 servo valve 761k4112b BYPASS NRV SIZE 2" TC11 SEAL OIL PUMP,AC DRIVEN HSNH660-40NZ Gasket D135A-242000A005 HRanti-corona varnish 1244 Shellac molding mica plate 5233 Neoprene rubber adhesive RTD temperature probe WZP2-231 generator end cap grease gun KH35 mica powder DF105 Solvent-free RTV adhesive 53841WC glass cloth Adhesive tape SCOTCH27 Current tranformer LJB1 Inlet valve Solenoid valve 4WE10D50/0FAG220NZ5L insulating box patch board 0.5 Cylinder sealing grease DFSS-1 2.5KG A/D converter DZXL-ZL-E-6682 RING, ANTI EXT DG600-240-07-02(4) shunt ring Z1c001297S RUBBER BLADDER NXQ-A-25/31.5-L-EH Pressure Transmitter 3051GP1A2B21BB4M5HR5 EH OIL PUMP DISCHARGE NRV D600K-589400A Low resistance Anticorona tape 0.1*25 Gap measuring probe GJCT-15-E epoxy adhesive 841 (A+B) Transformer WBV342S1 Coil Vickers 300AA00126A SEAL OIL PUMP,AC DRIVEN HSNH660-40NZ ã??2019-11-07-DFJerry
More than 750,000 submersibles have been successfully installed using Sudarshan uPVC Submersible Pipe upto depths of 1150 feet. Sudarshan uPVC Submersible Pipe is manufactured in different Dia – 1” to 4” in various ranges suitable for different depths and different pump delivery pressure. We manufacture Sudarshan Submersible Pipe using double stage bi-axial orientation technology & thread using CNC machines to ensure high precision. Stringent on-line quality checks, rigorous testing in our laboratory and continuous R&D activities over a decade helps us provide our customers with unmatched quality. Sudarshan uPVC Submersible Pipe unique feature is that it can sustain submersible pump high hydrostatic pressure, which is maximum in the bottom most pipes connected to the pump and can withstand the high tensile load of pump and entire submersible filled with water, which is maximum in the top most pipes. Sudarshan uPVC Submersible Pipe is most suitable for submersible pump and a perfect alternative to conventional G.I pipes. SEPL is marketing its submersible pipe all over India through a 240 distributor network and successfully exporting to GCC and Africa. Features: Square threads – Made on CNC Machines for high precision. They enable tension free grip & easy fitment. These are high friction threads on load which do not open even on constant forward and reverse torque of the pump. Rubber Gasket & Profile ‘O’ Ring – Permanent side is fitted with rubber gasket & temporary side with profile ‘O’ Ring to absorb pump vibration & to make it leak proof. ‘O’ Ring Locking System – Provides permanent lock between coupler and pipe as well as absorbs tension from torque generated by pump, providing incredible grip. Thick & Thin – Ends of the pipe are thicker than the barrel of the pipe so that even after threading there is maximum strength in the pipe. Biaxial Orientation Technology – Provides higher tensile strength and impact resistance Comparative Performance of uPVC Submersible Submersible Pipes. Criteria SEPL uPVC Submersible Pipe G.I. / M.S Pipe HDPE Pipe Life Span Long Life-Estimated life designed for 30 years; Pipes & its square threads do not deteriorate due to corrosion or rusting; and are designed to have high load capacity 5 to 10 years Pipes and its threads get damaged due to rusting and corrosion. Very Limited life Low strength, gets damaged under high pressure in span of 2 – 3 years Energy & Fuel Consumption; & Flow of Water Smooth Inner Surface leads to low frictional loss, providing higher output & Low energy and fuel consumption Rough inner surface leads to higher frictional loss; Hence consumes more energy and fuel, & gives higher water output Relatively Rough inner surface – lower output, higher energy consuption. Maintenance : Low Maintenance Very high maintenance; Rusting of threads needs periodic removal for rethreading of pipes and cleaning rust deposits Relatively High Maintenance Leakage Rubber ‘O Ring Locking System’ and rubber seals at the joints makes it completely leak proof Always Leaks – Pipe joints are not pressure tight, rusting of joint threads Pressure can cause leakage in pipes Installation: Light weight 3 metres length pipes are easy to install & remove Pipes are very heavy and difficult to handle, requiring great efforts in installation & removal Easy to install Advantages of Sudarshan uPVC Submersible/Submersible Pipe: Long life span upto 30 years Lower investment - 30% cheaper than GI Pipe 30% Lower operational cost – smooth inner walls give higher output and save power Suitable for Food Grade – GI pipe is unfit as it contaminates water due to rusting No corrosion or rusting No maintenance required Easy to install and uninstall No bacterial growth Physical & Mechanical Properties: Property Unit Standard Specific Gravity 1.4gms/cm3 - Vicat Softening Temperature 87.3 C as per ASTM D 1525 Technical Specifications of Sudarshan Submersible / Riser Pipe for Submersible Pump : Sl Size & Type OD - Outside Dia ND - Nominal Dia Ultimate Breaking Load (Kgf) Suitable Load (Kgf) safe allowable hydrostatic Pressure (Kgf/Cm2) Maximum Installation depth (Feet) Maximum Installation depth (Meters) OD: 33mm (1") ND:25 mm 1 Deluxe 1200 720 21 700 210 2 Super Deluxe 1800 1080 30 950 300 OD: 42mm (1.25") ND:32 mm 3 Deluxe 1800 1080 21 700 210 4 Super Deluxe 2500 1500 27 900 270 5 Heavy 3000 1800 35 1100 350 OD: 48mm (1 1/2") ND:40 mm 6 Deluxe 2500 1500 21 700 210 7 Super Deluxe 3000 1800 27 900 270 8 Heavy 4000 2400 35 1100 350 OD: 60mm (2") ND:50 mm 9 Super Deluxe 3750 2250 21 700 210 10 Gold 4500 2700 27 900 270 11 Heavy 4800 2880 27 900 270 12 Super Heavy 5700 3420 35 1150 350 OD: 75mm (2 1/2") ND:65 mm 13 Super Deluxe 4800 2880 17 550 170 14 Gold 6000 3600 21 700 210 15 Heavy 7200 4320 27 900 270 16 Super Heavy 9000 5400 35 1150 350 OD: 88mm (3") ND:80 mm 17 Super Deluxe 6900 4140 17 550 170 18 Gold 8100 4860 21 700 210 19 Heavy 9600 5760 27 900 270 20 Super Heavy 12600 7560 35 1150 350 OD: 113mm (4") ND:100 mm 21 Super Deluxe 9900 5940 17 550 170 22 Gold 12600 7560 21 700 210 23 Heavy 16000 9600 27 900 270 24 Super Heavy 20500 12300 35 1150 350 NOTE: We manufacture other pressure rating pipes & pipes of OD: 140mm (5") ND: 125mm on request WEIGHT CARRYING CAPACITY OF SUDARSHAN UPVC SUBMERSIBLE PIPE WITH PRESSURE RATING OF 21KGF/CM2, SUITABLE FOR SUBMERSIBLE PUMP INSTALLATIONS UPTO 210 METRES (700 FT) DEPTH Size & Type PIPE WEIGHT (Kg) For 210m Length Submersible Water Weight (Kg) For 210m Length Pump Set Weight (Kg) Approx. Cable Weight (Kg) Approx Total Weight (Kg) Max Load Capacity (Kg) For Pulling with Chain Pully Or Crane Ultimate Breaking Load (Kg) 1'' Deluxe 123 105 65 55 348 720 1200 1.25'' Deluxe 140 193 85 55 473 1080 1800 1.5'' Deluxe 182 266 130 55 633 1500 2500 2'' Super Deluxe 273 455 200 75 1003 2280 3800 2.5'' Gold 483 711 270 75 1539 3600 6000 3'' Gold 647 1022 350 95 2114 4860 8100 4'' Gold 1015 1733 500 145 3393 8100 13500 Selection of Pipes The pipe should be selected such that the pump delivery pressure does not exceed the hydrostatic allowable pressure of the pipe. Example: Pump Delivery pressure: 24kg/cm2 Pipe outlet Size & Pipe Size: 2’’ (50mm) Nominal Diameter 2’’ Super Delux recommended permissible pressure: 21kg/cm2 2’’ Heavy recommended permissible pressure: 27kg/cm2 In such case, 2’’ Heavy pipe should be selected. INSTALLATION PROCEDURE 1. First connect the male end of C.I/ M.S/ S.S bottom adaptor to submersible borewell pump using chain wrench. 2. Join the Sudarshan Pump Guard to the bottom Adaptor along with M.S/ S.S flange rod. 3. Now connect the first pipe to the female end of the pump guard. 4. Before connecting the pipes and pump guard, clean the threads with clean water and check for proper fitment of rubber sealing. 5. While fitting of pipe hold the coupler by hand / wrench. 6. Tighten the pipes by hand, until the rubber sealing in the pipe end completely enters into the coupling. However for better grip strap wrench can be used to hold/ tighten the pipes. 7. At the time of lowering the pump into submersible, the clamp must be fastened only to the portion marked as “Clamp Here”, i.e. just below the coupler. 8. Then all the other Sudarshan Submersible pipes can be connected the same way. Pipe wrench should not be used for support. 9. Once the top submersible pipe reaches the ground level, connect the top adaptor with male end connection. 10. Finally from the ground level regular plumbing accessories can be used to transfer water to required delivery point. Do not use oil on square threads of Sudarshan Submersible Pipes. Clean the threads with normal water and check the proper fitment of rubber sealing element INSTALLATION CONDITIONS: Full casing of bore well is recommended for long life of bore and pump. It prevents the pump from getting stuck due to lose boulders and stones. It also reduces chances of accident due to protruding stones and boulders at the time of removing the pump and pipe. In areas with loose soil & silt, Bore collapse problem may be more than in rocky areas. However, even rocky areas may have loose boulders. Hence, it is advisable to use full casing. PRECAUTIONS: Avoid Dry Run of Pump During dry run the submersible pump gets heated up and may damage or deform only the first pipe connected with the pump. Ways to avoid the dry running/ damage or deformation of the pipe: - Use timer switch to turn on or off the pump automatically as per the pre-set time. Pre-set time must be determined after assessing the bore yield to ensure pump does not run in dry condition. - Use of 3 metres of Steel Pipe between pump and SEPL uPVC Submersible Pipe will help dissipate the heat, preventing any damage or deformation. However, if the deformation is happening in any pipe other than the one connected to the pump, it is due to high pump pressure and wrong pipe selection. Prevention of Water Hammer At the time of pump stoppage, water recedes/falls at tremendous speed from a height. Especially in deep bore wells of about 500 ft & above, this creates enormous pressure and load on the pump and bottom most pipe called as water hammering. For such deep bore wells, it is recommended to make a 3mm hole in the pump NRV to protect the pump and pipe from water hammering. Handling & Storage of Pipes - Check for any visible damage to pipes during transit and inform immediately. - Avoid contact of pipe with any sharp objects. - Do not throw or drop the pipes from truck to the ground. - Store it in covered areas to avoid exposure to sunlight & UV rays - Stack pipes on even grounds with stack height not more than 7feet - Place alternate layers of pipes/bundles perpendicularly, with each layer forming a square. - Stack lighter pipes above the heavier ones, if pipes are of same diameter - Keep the stacking surface dry.
Stainless Steel hygienic food grade Milk exprosion-proof ABB Motor Centrifugal sanitary Pump Technical Parameter [Spec]: 3T-180T,6m-60m , 0.55KW-75KW [Material]: SUS304 SUS316L, The pump body, pump cover and impeller contact with medium made of SUS316L, SUS304. [Standards]: 3A,SMS,ISO,IDF,BS,RJT [Impeller]: Open type impeller, there is no blind corner. close type impeller, semi-open type impeller [Operate condition]: Sanitary centrifugal pump is close to HORIZONTAL transport of high and low level, is not the Self-priming type. [Surface treatment]: The part contact with mdedium is Polished, And other part is Sand Blasted [Max inlet pressure]: 0.5MPa [Temperature range]: -10 to Degree +140 Degree(EPDM) [Flushable mechanical sealing: ] Water pressure: __Max 0.1MPa Water lift: _______0.25-0.5L/min Flow (Ton) per hour Unit (SS304 explosion proof ABB motor) Unit(SS316L ABB explosion proof Motor Motor made in Chian ss304/316L) Inlet/Outlet(mm) Lift(Meter) 1T(0.55KW) 300 330 260/300 32/25 15 3T(0.75KW) 350 350 315/350 38/32 20 5T(1.5KW) 500 550 450/500 51/38 25 10T(2.2KW) 550 600 500/550 51/38 25/32 15T(3KW) 750 800 670/735 51/51 32/42 20T(4KW) 780 850 720/780 51/51 36/52 .............................................150Tons per hour the biggest one we can produce. [Motor]: 1. Configuration of "ABB" brand three-phase AC motor is in accordance with the International Electronically CommissionIEC60034. IEC60072 standard design comply with European "CE" Marking requirements 2. The Explosion-Proof motor also available, that can meet with the requirement of different Applications. 3...It has excellent electric performance, low noise and low vibration. The protection grade is IP55, insulation grade is F. 4. Operate in voltage: ≤ 3Kw, 220-240V/380-420V, Δ /Y > 3Kw, 380-420V/660-690V, Δ /Y 5. Frequency: _________50Hz/60Hz 6. Working method: ____Continuous(SI) 7. Rotate speed: ______The standard rotate speed is 2900r/min PS: Performance curve could be provided~ ONEMOSS is specialized in Manufacturing Sanitary Pumps Sanitary Valves Sanitary Pipe fittings etc. , which can be widely used in food, beer, beverage, dairy products, cosmetic, pharmacy and biology engineering field. For that our products will be applied in the fluid systems with strict sanitary and sterilizing requirement, so we do have many strict tests for our products, such as the performance curve test of pumps, frequency curve, the smooth and clean test, pressure test and so on.
Roots blower, magnetic drive pump.
IPP power plant Gear pump GPA3-25-E-20-R6.3 YOYIK is a professional sales, research and development, production in one of the manufacturing and processing companies. The company was established in 2004, YOYIK is a professional sales, research and development, production in one of the manufacturing and processing companies. After many years of hard work, now and hundreds of domestic and foreign power plants, steam plant suppliers to establish a good relationship of cooperation in the industry also received a lot of praise. I Acting Acting Actors can provide proof of origin and customs declaration list, sincerely welcome you to inquire. YOYIK provides multiple types of spare parts and equipments for power plant : #DF-Gear pump GPA3-25-E-20-R6.3-DF Semiconductor High resistance varnish HEC56616 sealant injector 5D463.338 T15 Servo 078N210E TENSION RING Part: 803 stator slot wedge 4Q9843 CREMER Probe CEL-3581F/G mannual sealant injector KH-32 Mechanical seal LTJ100 HZB253-640-00. Part: 41 Seal kit NXQ AB100/10-L bearing 6308 C3 SKF LVDT Sensor TD-1-150-15-01-01 Diluent DFCJ919TH Sealant KE-45 mica tape 14611 High Pressure EH Oil Fyrquel EHCPLUS HR anti-corona varnish 802 insulating washer 4B150 insulating box filling adhesive 135 epoxy air-dry varnish 1504 insulating water pipe assembly 1Q1634 RTV Heat conduction Semiconductor putty DECJ0901 silicon sealant 750-2 Gasket Pos.20 Semiconductor silicon rubber HEC51104 Cylinder sealing grease MFZ-1 Two-component adhesive 53841 red insulating varnish DECJ1348 TITESEAL T25-66 Pneumatic Cylinder sealing kit for Dome valve DN50 DN50 grease gun 5D463.338 T15 Gear pump GPA3-25-E-20-R6.3 Insulation gasket 3Q4557 Insulating paint DFCJ1345 LVDT sensor HL-6-150-15 LR anti-corona varnish 130 mannual grease gun KH35 Adhesive powder mica tape 5461 Gas turbine cleaner ZOK-27 oil proof rubber board 3707 Rotation speed sensor CS-2 epoxy potting varnish 944 Globe valve J61H-25 Plug item 4b rotor slot wedge 3Q6198 Vent piping YOT51-20-00 epoxy Polyester air-drying clear varnish 9120 fiberglass tape 2450 H-class 0.15*25 Servo valve G761-3033B H-grade varnished glass cloth tape 2450 0.15*25 generator sealant injector KH-32 SENSOR SPEED SZCB-01 LVDT Sensor TD-1 0-100 grease gun KH35 Air-dry Polyester Red Insulating Varnish DECJ1348 RTV epoxy adhesive DECJ0139 Press. Reducing Valve Y967H-150LB insulating water pipe assembly 1Q1631 red insulating varnish 183 Varnished Glass fabric DECJ0703 sealant HDJ-750-2 Semiconductor High resistance varnish HEC-56615 Gear pump GPA3-25-E-20-R6.3 DFYL-2020-7-8-MY
“Sabar” 10"Submesible Pumpset - Water Filled are in Three Phase suitable for 10" & above bore well size. The Head range is from 4 Mtrs. to 264 Mtrs. & Discharge Range is from 50 LPM to 4000 LPM. Motor HP Range is from 15 HP to 125 HP. Pump Stage range is from 1 Stage to 13 Stages. The Salient Features of 10" Submersible Pumpset - Water Filled are as under : 1) Wet type, Water Cooled Rewindable Motors 2) Withstands wide voltage fluctuations 3) Most of the models have ISI marks 4) Available with Stainless Steel & bronze MOC 5) Long life due to study construction. The Applications of 10" Submersible Pumpset - Water Filled are as under : 1) Field Irrigation 2) Private / Public Water Supply 3) Fow / Drip / Sprinkler Irrigation 4) High Rise building water supply 5) Fire Fighting. Standard Export Wooden Box Packing.
Specifications 1. Integrated&compact design,nice outlook and easy installation 2. High COP as 4.0,saving operation cost Warranty: 24 months guarantee for the whole unit. Features: 1.Safety:water and electric separately. 2.Simple installation:Compact design(Main unit and water tank),DIY installation is available to saving costs! 3.Conveninet:Intelligent remote controller,with simple key operation.Displays error code when having problem,easy for maintenance. 4.Multiple protections for the whole heat pump, guaranteeing safe operation. 5.World famous brand compressor,4-way valve,motor,PCB,heat exchanger used to ensure top quality and high efficiency. 6. All weather operation:stable operation without being influenced by weather. 7.Metal case and stainless steel case are available,R22,R407C,R410a,R417A,R134A are for optional. 8.Metal case water tank with powder coating or stainless steel case are available. 9. Quiet:Special design for motor and fan to decrease noise, no disturbance to owners and neighbours. Air to water heat pump(All In One type) Parameters Model DBT 4.0I-200 Rated Heating capacity kW 4.0 kcal/h 3444 Rated hot water capacity L/H 80 Rated power input kW 1.052 COP W/W 3.8 Rated operating currentA 4.9 Power supply 220V/1PH/50Hz Rated output water temperature °C 55 Maximum output water temperature °C 60 Compressor Type High-efficiency & Low-noise Totally Enclosed Rotary Water side heat exchanger Type High-efficiency interior screw coil Water Tank Volume L 200 Gas inlet mm 6.35 Gas outlet mm 9.52 Air side heat exchanger Type Hilicl fin Hydrophilic aluminum foil exchanger Fan Type Low-noise Wide-blade Axial Fan Fan Quantity 1 Fan Power input 25 Refrigerant Type R410A Unit noise level dB(A) 44 Working temp. range °C Water inlet & outlet G3/4" Dimensions Unit mm 680 x 1650 Package 695 x 695 x 1750 Weight Kg78 Note: 1.Rated heating conditions: ambient temperature DB20°C WB15°C, Initial/Final water temperature: 15°C/55°C 2.The above designs and specifications might be changed without prior notice for product improvement
Jute File Holder Natural and colored jute combination, 14/15, magnet button closure, inside non-woven liner with 2xA4 paper pocket and 1 pen holder Utility: Personal Office Stationery Body Dimension (inch) : Height: 14 Width : 10
Warranty: 24 months guarantee for the whole unit. Features: 1. Safety:water and electric separately. 2. Using complete free hot water when the unit is operating at cooling model,super energy-saving and environment protection! 3.Five models are available,Hot water,Heating,Hot water+heating,Cooling+Hot water,Cooling. 4.Conveninet: Intelligent remote controller,with simple key operation.Displays error code when having problem,easy for maintenance. 5.Multiple protections for the whole heat pump, guaranteeing safe operation. 6.World famous brand compressor,4-way valve,motor,PCB,heat exchanger used to ensure top quality an high efficiency. 7. All weather operation: stable operation without being influenced by weather. 8.Metal case and stainless steel case are available,R22,R407C,R410a,R417A,R134A are for optional. 9.Metal case water tank with powder coating or stainless steel case are available. 10.Simple installation: rooftop, balcony, yard or basement can be suitable places for the installation. 11.Quiet: Special design for motor and fan to decrease noise, no disturbance to owners and neighbours. OEM for famous brand type Multi function Heat Pump Water Heaters 1873 Air sources heat pump+Air conditioner(Heat recovery function) Parameters Mode lDBT 5.0HR Rated Heating capacity kW 5.0 Hot Water Rated hot water capacity L/H 115 Rated power input kW 1.19 COP W/W 4.2 Rated operating current A 5.4 Rated output water temperature °C 55 Maximum output water temperature °C 60 Water pipe(Inlet/Outlet) Inch Heating capacity Rated Heating capacity kW 5.0 Rated power input kW 1.19 COP W/W 4.2 Rated operating current A 5.4 Refrigerant pipe(Liquid) Inch 1/4' Refrigerant pipe(Gas) Inch 1/2' Cooling capacity Rated cooling capacity kW 3.5 Rated power input kW 1.34 EER W/W 2.61 Rated operating current A 6.1 Refrigerant pipe(Liquid) Inch 1/4' Refrigerant pipe(Gas) Inch 1/2' Power supply 220V/50Hz-60Hz Compressor Type Rotary Refrigerant Type R22&R407C&R410a Unit noise level(Indoor/Outdoor) dB(A) 39/44 Working temp. range °C -7~43 Dimensions Indoor Unit(Net) mm 790 X 270 X 205 Package 865 X 360 X 240 Outdoor Unit(Net) 780 X 260 X 540 Package 915 X 345 X 600 Water tank(Net) 470x1400 Package 550x1480 Weight Indoor Unit (Net/Gross)Kg 10(12) Outdoor Unit(Net/Gross)40(44) Water tank(Net/Gross)37 Note: 1. Rated heating conditions: ambient temperature DB20°C WB15°C, Initial water temperature: 15°C, Final water temperature: 55°C 2. The above designs and specifications might be changed without prior notice for product improvement
Offer the replacement /rebuilt /genuine for the various hydraulic pump for lots of brand such as rexroth, vickers, denison, poclain, parker, caterpillar, tokimec, etc. We suggest the rexroth pump as like a10vso / a4vso / a4vg /a11vo / a10vg / a4vsg / a6vm / a6ve / a2fo / a2fm/a2fe / a7vo /a8vo /a2vk /mcr, a2fm (o)10/12/23/28/55/80/107, etc; vickers 2525v / 3520v / 3525v / 4520v, 20vq / 25vq / 35vq / 45vq / 2520vq, denision - t6c / t6d / t6e /t6cc / t6ed / t6dd / t6de etc Service : offer replacement, genuine & rebuilt. The replacement means for the required product made in china fully interchangeable with genuine, as its technique and function is same as the data of the genuine itself. The rebuilt means for the used genuine to be repaired and refurbished and make its function and appearance same as the brand new genuine. The genuine is made in the original brand country, such as the brand bosch rexroth is in germany. Pls feel free to give us your specific style number. We will bring you the best product and service at most competitive rate. Sincerely hope to build up the close business relation with you on basis of the mutual benefit in a long term. Thank you. Packed with wooden box
Offer replacement /genuine for various hydraulic spare parts of pump/ motor/ excavator (etc.) for lots of brands such as rexroth, vickers, poclain, parker, caterpillar, yuken, komatsu, etc. We suggest the parts as like charge pump, cartridge kit, rotary group, piston shoe, cylinder block, valve plate, retainer plate, ball guide, drive shaft, swash plate, press pin, snap ring, back cover, saddle bearing, bearing seat, shaft seal, etc, ... Service : offer replacement, genuine. The replacement means for the required product made in china fully interchangeable with genuine, as its technique and function is same as the data of the genuine itself. The genuine is made in the original brand country, such as the brand bosch rexroth is in germany. Pls feel free to give us your specific style number. We will bring you the best product and service at most competitive rate. Sincerely hope to build up the close business relation with you on basis of the mutual benefit in a long term. Thank you. Box
Product Details Full steam generator using natural magnet copper float level controller, regardless of antioxidant water quality, waste heat recovery 2 times longer life, saving over 30%. Safety, energy conservation, environmental protection, adjustable automatic electric steam generator Equipment Features: 1.This equipment no noise, no pollution, environmentally-friendly, clean, long life. 2.Compact structure compact, and flexible installation, small footprint. 3.High thermal efficiency, energy saving, low operating costs. 4.There are multiple electrical protection and mechanical protection, security measures to improve, safe, stable and reliable. 5.Over pressure, water and other failure operation, immediately cut off the main circuit power supply, to ensure personal safety equipment, and audible alarm signal. When the water level rose 2L machine automatically heated, add to the maximum level is automatically closed. Product Usage: The equipment and dry cleaning machines, washing machines, ironing Equipment washing machine, iron and other supporting; electric steam generator is the use of electric hot water is converted to steam equipment. Internal heating element is inserted in the cylinder, the power to make the barrel body of water temperature, saturated steam to produce hot water. At the top of the cylinder has a steam valve or valve, safety valve, pressure gauge, pressure controller, water level sensors in the lower cylinder has intake, outfall, fitted to the pump on the base, with pipes, valves to it communicates with the cylinder. The products are widely used in the chemical industry, machine repair, footwear, textiles, packaging, factories, offices, hospitals, canteens, hotels, guest houses, restaurants and other places, to provide users with the production of the required life of small-capacity steam.
MRP: Rs. 1,499 Monsoon Essential Combo Monsoon brings a lot of pet peeves. Boost your pet's immunity this season by investing in Wiggles health essentials. The Wimmuno+ Immunity Booster is the only pet immunity supplement that gives comprehensive immunity by activating macrophages, producing cytokines, activating immunity systems and preventing oxidation through natural antioxidants. Build your pet's gut health this monsoon with Stripzy (tm), a fast-acting probiotic strip that dissolves easily in the mouth and aids digestion. Give your best furriend a quick waterless bath with Naturopet and get Ravtix, an easy-to-spray tick solution that prevent thos pesky monsoon ticks and lice. GET THE DOSE RIGHT: Naturopet: Use when your pet gets dirty, for adult pets use twice a week or use daily incase of skin infection. Spray over pet�?�¢??s body, let it soak in for a few minutes, massage slightly and then comb from head to tail. Ravitix: Apply by holding the pump approximately 12 inches from the pet's body. Apply at different areas. Do not apply on an open wound. Stripzy: Recommended Usage: Open your pet�?�¢??s mouth, place the strip on the tongue and let it dissolve For small dog breeds or cats: 1 strip once a day for 3 to 5 days or as directed by your veterinarian For medium and large dog breeds: 2 strips per day for 5 to 7 days or as directed by your veterinarian Preferably to be consumed before meals Wimmuno: Dogs: 10 -15 ml; Twice Daily Puppies & Cats: 5 ml; Twice Daily or as directed by veterinarian PRECAUTIONS: Naturopet: Avoid sensitive areas like eyes, mouth and snout. Ravitix: Avoid spraying on the face, minor cuts, bruises and open wounds. Avoid contact with your skin, eyes or clothing as it may cause irritation. Not intended for puppies/kittens under 8 weeks of age or pets that are pregnant. In case of any sign of allergic reactions, immediately bathe your pet with a mild shampoo and rinse with water. Consult a vet if required. Wash hands properly using soap and water after application. Flammable. Keep it away from fire. Stripzy: Protect from moisture and direct sunlight. Store at room temperature. Wimmuno+: Use recommended doses. For animal use only. HOW TO STORE: Naturopet: Keep in cool and dry place. Lid to be tightly closed after use. Keep away from direct sunlight. Ravitix: Store in a cool & dry place. Keep away from direct sunlight. Sripzy: Store in a cool and dry place. Do not consume if found open or damaged. Wimmuno+: Store in a cool & dry place. Keep away from direct sunlight.
Water pump, sewage pump, diaphragm pump, magnetic pump, oil pump.
Heat exchangers, homogenizer special flange motors, dosing pumps, centrifugal pumps, magnetic pumps, gear pumps..
