ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system. Product Features: 1. Standardized components, modular architecture, easy for expansion 2. High energy density, small footprint, short construction period, strong environmental adaptability 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH-500KWH optional 5. The use of international advanced Mitsubishi IPM module and intelligent power module, with high power fast adjustment capability 6. BMS battery management system with SOC automatic calibration and high current active balance function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 7. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system 8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform 9. PV charge controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of PV modules and batteries 10. Colorful LCD display all module working information and status.
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system. Product Features: 1. Standardized components, modular architecture, easy for expansion. 2. High energy density, small footprint, short construction period, strong environmental adaptability 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH--500KWH optional 5. BMS battery management system with SOC automatic calibration and high current passive balancing function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 6. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system. 7. Our BMS system adopts American NXP automotive grade chips with high performance. 8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform. 9. Colorful LCD display all module working information and status.
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system. Product Features: 1. Standardized components, modular architecture, easy for expansion. 2. High energy density, small footprint, short construction period, strong environmental adaptability 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH--500KWH optional 5. BMS battery management system with SOC automatic calibration and high current passive balancing function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 6. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system. 7. Our BMS system adopts American NXP automotive grade chips with high performance. 8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform. 9. Colorful LCD display all module working information and status.
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system. Product Features: 1. Standardized components, modular architecture, easy for expansion. 2. High energy density, small footprint, short construction period, strong environmental adaptability 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH--500KWH optional 5. BMS battery management system with SOC automatic calibration and high current passive balancing function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 6. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system. 7. Our BMS system adopts American NXP automotive grade chips with high performance. 8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform. 9. Colorful LCD display all module working information and status.
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system. Product Features: 1. Standardized components, modular architecture, easy for expansion. 2. High energy density, small footprint, short construction period, strong environmental adaptability 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH--500KWH optional 5. BMS battery management system with SOC automatic calibration and high current passive balancing function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 6. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system. 7. Our BMS system adopts American NXP automotive grade chips with high performance. 8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform. 9. Colorful LCD display all module working information and status.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system. Product Features: 1. Standardized components, modular architecture, easy for expansion. 2. High energy density, small footprint, short construction period, strong environmental adaptability 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH--500KWH optional 5. BMS battery management system with SOC automatic calibration and high current passive balancing function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 6. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system. 7. Our BMS system adopts American NXP automotive grade chips with high performance. 8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform. 9. Colorful LCD display all module working information and status.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Product Introduction SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-1000VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface
Product Introduction SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-1000VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface
Product advantages: ï?¬All-in-one design, high integration and space saving installationï¼? ï?¬Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 yearsï¼? ï?¬Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics Built-in BMS management system with comprehensive protection and monitoring control functions 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells Main control MCU can be centrally controlled and manage peripheral settings (AC charging module, inverter module, solar charging module) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable BMS battery management system, with SOC automatic calibration and high current passive balance function, combined with perfect operation control and management strategy, to achieve accurate and efficient management EMS energy management system, BMS with solar controller/AC charger, inverter centrally manages charge and discharge, effectively controls the charge and discharge current within the cell usage conditions, protects the cell and extend its service life
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
MPPT Solar charge controller Feature 1. We choose high speed and high performance 32-bit processor with excellent EMC design 2. Advanced MPPT tracking algorithm, the tracking efficiency more than 99% 3. High performance IGBT power module as electronic switch, there is no any mechanical switch, plus multiphase synchronous rectification technology, improves the stable greatly 4. Ultrafast maximum power point tracking speed to ensure tracking efficiency 5. Accurate identification and tracking of multi-peak maximum power points 6. With current-limiting charging function, charging current can be set, friendly and compatible with various capacity batteries. 7. Widely PV arraysâ?? voltage input, this can save the cost of PV combiner box, wires and construction 8. Full enclosed duct design and high-speed fan for cooling makes the controller suitable for various harsh environment 9. It shows the ambient temperature. It also has automatic temperature compensation function and RTC real time function 10. The perfect battery protection function and multi-stage charging improves battery life 11. It has the statistical function of generating capacity which is very convenient for customers to view the daily, monthly and total charging capacity of the controller. 12. Complete menu display and operation, plus the humanized design of browsing interface, these makes the operation more easy 13. It can work with GEL. LEAD-ACID, LITHIUM and other type battery 14. Twice protection function to protect battery from damage when the power switch is down (optional) 15. Standard Modbus communication protocol for RS-485 or GPRS communication to extend the communication distance (optional function)
The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stations need, there are 48V 96V 120V192V 220V 240V 360V 384V 480V 492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)
The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stationsâ?? need, there are 48Vã??96Vã??120Vã??192Vã??220Vã??240Vã?? 360Vã??384Vã??480Vã??492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)
The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stations need, there are 48V 96V 120V 192V 220V 240V 360V 384V 480V 492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)
Features : 3 times peak power, excellent loading capability. Combine inverter/solar controller/battery all in one. Multiple output : 2 'C output socket, 4*DC 12V, 2* Working mode AC prior/ECO mode/Solar prior selectable AC charging current 0 1 0A selectable. LVD/HVD/Charging voltage adjutable, suitable for kinds of battery Adding fault code to monitor real time work situations Continuous stable p ure sine wave output with inbuilt AVR stabilizer . Digital LCD and LED for visualization of operation status of the equipment. Inbuilt automatic AC charger and AC mains switcher, stwitch time 4ms
Features : 3 times peak power, excellent loading capability. Combine inverter/solar controller/battery all in one. Multiple output : 2*AC output socket, 4*DC 12V, 2* Working mode AC prior/ECO mode/Solar prior selectable AC charging current 0 1 0A selectable. LVD/HVD/Charging voltage adjutable, suitable for kinds of battery Adding fault code to monitor real time work situations Continuous stable p ure sine wave output with inbuilt AVR stabilizer . Digital LCD and LED for visualization of operation status of the equipment. Inbuilt automatic AC charger and AC mains switcher, stwitch time 4ms
Features : 3 times peak power, excellent loading capability. Combine inverter/solar controller/battery all in one. Multiple output : 2*AC output socket, 4*DC 12V, 2* Working mode AC prior/ECO mode/Solar prior selectable AC charging current 0 1 0A selectable. LVD/HVD/Charging voltage adjutable, suitable for kinds of battery Adding fault code to monitor real time work situations Continuous stable p ure sine wave output with inbuilt AVR stabilizer . Digital LCD and LED for visualization of operation status of the equipment. Inbuilt automatic AC charger and AC mains switcher, stwitch time 4ms
