Product name: I-shaped inductor Category: Chip Inductor Series Product introduction: Volume: 0402, 0603, 0805, 1206, 2520, 3225, 4532, 5650 Tolerance: I=±7%, K=±10%, L=±15%, M=±20% Sense: 1.2N 1.5N 2.2N 3.9N 6.8N 1R0K 1R2K 2R2K 2R7K 3R3K 4R7K 10u 15u 12u 18u 22u 1MH 1.2MH 1.5MH 1.8MH 2.2MH Features: 1. High-precision wire-wound inductors suitable for automatic placement; 2. Good solderability; 3. Heat-resistant resin encapsulation, with excellent mechanical strength; 4. Excellent Q value and high reliability; 5. Used in LCD TVs, computer drives, mobile phones, car stereos and other electronic products.
WAYJUN this signal isolated splitter product uses advanced isolated technology, quarantine inspection / monitoring DC voltage signal, small size,low power,high accuracy. Input/output/auxiliary power supply three isolation.Widely used in such fields as electricity, chemicals, petroleum, industrial and automatic control. Selection Guide: 1.Input:0-5V Power Supply:24V Output:two 4-20mA Type No.: DIN12 IAP- V1-P1-A4 2.Input:0-10V Power Supply:24V Output:0-10V/4-20mA Type No.: DIN12 IAP-V2-P1-V2A4 3.Input:4-20mA Power Supply:24V Output:two 4-20mA Type No.: DIN12 IAP- A4-P1-A4 4.Input:0-10V Power Supply:24V Output:two 0-10V Type No.: DIN12 IAP V2-P1-V2 Features: >> One input two output >> Accuracy: 0.1%, 0.2% >> Isolation : signal input / output / auxiliary power 3000VDC >> One standard signal input: 0-5V / 0-10V/1-5V, 0-10mA / 0-20mA/4-20mA >> Two standard output signal: 0-5V / 0-10V/1-5V, 0-10mA / 0-20mA/4-20mA >> Dimensions: 106.7x79.0x25.0mm >> Auxiliary power supply: DC5V(± 10%), 12V,15V, 24V(8-32VDC) >> Insulation resistance :â?¥ 20MΩ >> Operating Temperature : -25 to +80 ° C >> Pressure : signal input / output / auxiliary power >> Operating Humidity :10 ~ 90% (no condensation) >> Storage Temperature :-45 ~ +80 >> Impulse withstand voltage : 3KV, 1.2/50us (peak value) >> Storage humidity :10 ~ 95% (no condensation)
Cisco GLC-LH-SM Compatible 1.25G SFP Optical Transceiver 20KM ITEM NO.:ES3112-3LCD20 DATA RATE:1.25G DISTANCE:20KM CONNECTOR:LC PRODUCT ORIGIN:Made in China SHIPPING PORT:ShenZhen Package type: Individual package or 10pcs/package Features 1.Data-rate of 1.25Gbps operation 2.1310nm FP laser and PIN photodetector for 20KM transmission 3.Compliant with SFP MSA and SFF-8472 with duplex LC receptacle 4.Digital Diagnostic Monitoring:Internal Calibration or External Calibration 5.Compatible with SONET OC-24-LR-1 6.Compatible with RoHS 7.+3.3V single power supply 8.Operating case temperature:Standard : 0 to +70ï¼? Extended : -20 to +85ï¼?Industrial : -40 to +85 Applications 1.Gigabit Ethernet 2.Fiber Channel 3.Switch to Switch interface 4.Switched backplane applications 5.Router/Server interface 5.Other optical transmission systems
Overview: The FHC-00 high frequency induction fusion is the newly developed by RUISHENBAO® analytical (shanghai) Co., Ltd to prepare glass disks (beads) for X-ray fluorescence (XRF), and solutions for AAS and ICP. Fusion system has been widely used as a necessary device for XRF and AA sample preparation. The FHC-00 combines exceptional fusion accuracy with all the advantages of electric power, more speed, simplicity for experienced, and novice user. It has some features, like good repeatability, flexibility, high precision, short sample preparation time, cleaner, more reliable, low cost and so on. This fusion has two sample positions that it is designed to manage up to 2 samples at the same time with the same control unit, or each one of the sample position can work synchronized in a completely independent manner, with different programs. It effective both in high and low temperatures. The FHC-00 is highly automated unit to control and monitor in real time temperature of the fusion process of one or two samples simultaneously by high-precision IR pyrometer and PID thermostatic control. These enables the user to reach high temperatures in just a few seconds and to effectively control the fusion temperature. Meanwhile, the FHC-00 has two cooling systems, two magnetic stirring system to stir solutions, and a gas extraction system. Touch-screen programmable controls for fusion process like flexible setting of melting temperature, melting and cooling time, crucible rocking movement for homogenization of the melt, and flexible setting of melt pouring facilitated by vibration. Features: ï�® Flexibility, versatility: glass beads for XRF, solutions for AAS and ICP; ï�® High frequency induction heating system, only need mean 20s from ambient temperature to 1200â??; ï�® Multi-sample: 2 positions, up to 2 samples per 5-10min; ï�® Safety, simplify and reliable operation thanks to LCD touch screen; ï�® Non-contact and real time temperature measurement by high-precision IR pyrometerï¼?PID thermostatic control; ï�® 5 independent adjustable sample programs can be stored under PLC intelligent control system; ï�® Automatic rocking of crucible during fusion to ensure a homogeneous and bubble-free melt by program control. ï�® Automatic melt pouring to ensure the high sample smoothness. Fully automatic, superior accuracy, homogenization and smoothness ensure the superior reproducibility of the sample. ï�® Using heat-resistant ceramic platinum to protect crucible and casting dish; ï�® Equipped with powerful extraction systems in melting chamber to timely drain away harmful gas of fusion process. ï�® Multi-protectionï¼?Over-pressure, over-current, over-heat, excess temperature and lack-water alarm; ï�® Low using, maintenance and repair cost. Showing high performance-to-price ratio.
Speicifcation: Type Lp7552 electronic digital weighing indicator A/d rate 10 times/second Capacity 15kg~10000kg Resolution 1/3000, 1/6000, 1/15000 Suitable for Floor scale, platform scale, bench scale, animal scale, weighing bar etc Dimension 270mm x 202mm x 141mm Power supply 6v4ah rechargeable battery or 110/220vac N.W. 1.8kg Interface Rs232, usb, ethernet for option Load cell 1~4 pcs (350ohm)
Nominal current(rms):50/100/200/300/400/600a Voutipn:+4.000v Measuring range:0~+900a Supply voltage dc:+15v Accurancyipn, +25degree Celsiusless than1.0% Mounting(mm):10.5*20.5 * open- loop supply voltage: dc +15.0v * capable measurement of currents: dc, ac, pulse with galvanic isolation between primary circuit and secondary circuit.
Nominal Current(RMS):30/300A Vout@Ipn:2.500+_2.000V Measuring Range:+_30/+_300A Supply VoltaIpn,+25
Pen type design, easy operation, the unique large-screen OLED color display High repeat-ability, with replaceable battery compartment Measure the hardness scale HB, HRC, HRB, HV, HS, HL and strength Ï?b Compatible with D or DL impact device Display Type:1.77 inch OLED with resolution 160x128 pixels Hardness Scale:HL, HB, HRB, HRC, HV, HS, Strength (Ï?b) Measuring Range:HLD (200-960) HRC(19.8-68.5) HB(30-651) HV(80-976) HS(26.4-99.5) HRB(13.5-100)Ï?b (375-2639) Impact Device:D type impact device (Standard) Accuracy:Measuring Error:+ - 6HLD (HLD=800), Repeatability:+ -6HLD (HLD=800) Measuring Direction:360 degree Material:Steel& Cast Steel, Stainless Steel, GC IRON, NC IRON, Cast Aluminum alloy, Copper-zinc alloy, Copper-tin alloy, Brass, Forged Steel, Alloy Tool Steel Resolution:1HL, 1HV, 1HB, 0.1HRB, 0.1HRC, 0.1HS Calibration:Automatic Language:English, Chinese, Spanish, Japanese Data Memory:100groups (each group includes 1 TO 7 testing values and 1 average value) Power:10440 Polymer li-ion battery, Capacity of 600 MA/H,voltage:3.7 V, warning under low voltage Shut-off:Auto off after 3 minutes of inactivity
P/N: M2734B hp TOCO Transducer 100% original Latex free one year warranty 1pcs/box
Pressure range: -1 20 bar(optional) Accuracy: 1%F.S. Supply voltage: 5VDC, 12VDC, 3.3VDC Output: 0.5-4.5V, Others on request Operating temperature: -40 105 Compensation temperature: -20 80 Operating Current: 3mA Temperature drift (zero & sensitivity): 0.03%FS Long-term stability: 0.2%FS/year Response Time: 4ms Overload pressure: 150%FS Burst pressure: 300%FS Cycle life: 500,000 times Pressure connection: NPT1/8 by default, Others on request Electrical connection: Packard connection Housing Material: Copper Shell Water-proof level: IP65 Explosion-proof level: Exia CT6 Weight: 0.08kg Medium: non-corrosive environment Sensor core: Al2O3-96% ceramic sensor Cable length: 0.3m for Packard, 0.5m for plastic direct cable by default
1.Features: Good constant inductors properties and anti-dc bias capability. With low-loss 2.Applications: . Output filter inductors, smoothing inductors, energy storage inductors . Energy-saving lamp electronic ballasts, and the differential-mode inductance in the EMC filter
Ratio 1000: 1 , 2000:1, 1000:5 (customized) Accuracy class 0.1%, 0.2%, 0.5% Primary current 0 - 500A AC and 0-1000A AC Signal output 1mV/A, 1mA/A Secondary voltage 0 - 0.5V AC and 0 - 1V AC; Secondary current 0-1A or 0-5A AC Max. Cont. Input current 1200A Load capacity 4 Over voltage category CAT III 600V Frequency range 10Hz-10MHz Dielectric strength 3KV 50Hz/60Hz at 1minute Temperature range -40C to +55C Output 2.5 meter cable with D01 or BNC connector Max. voltage not insulated conductors 600 V Standard EN 61010-1, EN 61010-2-032, IEC60044-1 Installation clamp type Output mode lead output(2.5m) Accuracy (1000A Range) 0-10A 0.5% 10-100 0.2% 10-1200A 0.1% Phase Shift(1000A Range) 0-10A 0.5 10-100 0.2 100-1200A 0.1 Mechanical parameters Dimensions (L x W x H) (mm) 105 x 218 x 30 Weight (g) 650 Holding wire diameter (mm) 52 Max. jaw opening (mm) 52 Jaw color Red & Grey Material PC+ABS, UL94 V0
FEATURES Suitable for 5A, 10A cable online measurement Holding wire diameter: 8mm Dimension: 42.6mm 122.5mm 23mm Load capacity: 4 Installation: clamp type Output mode: lead output PARAMETERS Electrical parameters Ratio 1000: 1 or 2000:1 (customized) Accuracy class 0.1% Primary current 0 - 10A AC Secondary current 0 - 10mA AC (customized) Max. Cont. Input current 12 A Load capacity 4 Over voltage category CAT III 600V Output signal (AC current) From 0 to 10mA AC at nominal input current Output signal (AC voltage) From 0 to 100mV AC at nominal input current Frequency range 40Hz-2000Hz Dielectric strength 3KV 50Hz/60Hz at 1minute Temperature range -20C to +55C Output 2.5 meter cable with D01 connector Max. voltage not insulated conductors 600 V Standard EN 61010-1, EN 61010-2-032, IEC60044-1 Installation Clamp type Output mode Lead output(2.5m) Mechanical parameters Dimensions (L x W x H) (mm) 42.6x122.5x23 Weight (g) 250 Holding wire diameter (mm) 8 Max. jaw opening (mm) 8 Color Black Material PC+ABS+Polycarbonate, UL94 V0
Function & Feature 1. Isolate the DC input signal from the DC Output signal, which is directly proportional to the input signal. 2. These isolators can be used to prevent earth loops, which occur when a measuring source 3. Excellent temperature characteristic and good working stability. 4. It have an advantage over loop powered units, in that if for any reason the output lead should become disconnected, the input will not be saturated. 5. Fixed in a standard 35mm DIN rail or screwed on the cabinet.
Function & Feature 1. QPPX electrical transducer measures a wide range of electrical parameters and generates analog or digital output signals suitable for interfacing with instrumentation and control systems. Total four channel output, with panel key or PC control programmable, user can free to set 4 different data from max 26 electrical parameter for sampling and analog signal output. 2. Have three channel digital inputs and optional RS485-Modbus communication functionality. Can monitor the galvanically isolated DI signal and programmed the transducer with customized SCADA software. Any of the measured parameters can be read out via the optional RS485-Modbus connection. 3. QPPX also can be used to configure the connection to the measured circuit for single-phase, three-phase three-wire, three-phase four-wire, balanced or unbalanced load. Can be connected to a variety of measuring and control devices and systems, such as analogue meters, PLC, computers, data loggers, digital instruments and telemetry systems. 4. Snap on to DIN rail 35 x 7.5 mm complies with DIN-EN 50022 BS 5584
Function & Feature 1. Isolate the DC voltage input signal from the DC Output signal, which is directly proportional to the input signal. 2. These isolators can be used to prevent earth loops, which occur when a measuring source 3. Excellent temperature characteristic and good working stability. 4. It have an advantage over loop powered units, in that if for any reason the output lead should become disconnected, the input will not be saturated. 5. Fixed in a standard 35mm DIN rail or screwed on the cabinet. 6. Ultra-thin dimension, suitable for limited space, the control cabinet.
Function & Feature 1. Isolate the DC voltage input signal from the DC Output signal, which is directly proportional to the input signal. 2. These isolators can be used to prevent earth loops, which occur when a measuring source 3. Excellent temperature characteristic and good working stability. 4. It have an advantage over loop powered units, in that if for any reason the output lead should become disconnected, the input will not be saturated. 5. Fixed in a standard 35mm DIN rail or screwed on the cabinet.
Function & Feature 1. QPCX electrical transducer converts ac current and voltage signals into a load independent dc signal proportional to active power (watt), reactive power (var) and power factor (PF). With an extra output channel for customized. Total four channel output for electrical data sampling use. 2. The current and voltage signals are passed into the circuit via precision instrument transformers to provide galvanic isolation between the input circuits and the transducer circuitry. Each pair of current and voltage signals is mathematically multiplied together to produce a product signal proportional to true power and independent of wave shape and phase angle. 3. This combination transducers with RS485 communication port, it can be connected to a variety of measuring and control devices and systems, such as analogue meters, PLC, computers, data loggers, digital instruments and telemetry systems. 4. Snap on to DIN rail 35 x 7.5 mm complies with DIN-EN 50022 BS 5584
Function & Feature 1. QPK transducer converts ac current and voltage signals into a load independent dc signal proportional to reactive power (vars). This signal is capable of driving a number of independent instruments. 2. The current and voltage signals are passed into the circuit via precision instrument transformers to provide galvanic isolation between the input circuits and the transducer circuitry. Each pair of current and voltage signals is mathematically multiplied together to produce a product signal proportional to true power and independent of wave shape and phase angle. 3. These var transducers to be connected to a variety of measuring and control devices and systems, such as analogue meters, PLC, computers, data loggers, digital instruments and telemetry systems. 4. Snap on to DIN rail 35 x 7.5 mm complies with DIN-EN 50022 BS 5584
Function & Feature 1. Isolate the DC input signal from the DC Output signal, which is directly proportional to the input signal. 2. These isolators can be used to prevent earth loops, which occur when a measuring source 3. Excellent temperature characteristic and good working stability. 4. It have an advantage over loop powered units, in that if for any reason the output lead should become disconnected, the input will not be saturated. 5. Fixed in a standard 35mm DIN rail or screwed on the cabinet. 6. Ultra-thin dimension, suitable for limited space, the control cabinet.
