Almandine Garnet is the heaviest and hardest of all abrasives in this world. � Garnet is a relatively hard mineral with a hardness that ranges between 6.5 and 7.5 on the Mohs scale. It could withstand in highest cutting speed and maintain low dust levels, with its crystalline shape giving a fast cutting action and longer life span. Garnet has served primarily for its many dimension applications i.e. blast media, water jet cutting, coated abrasives, surface preparation, grinding media, water filtration and so on.
White fused alumina for abrasive and refractory belongs to the group of electro-corundum. It is produced by controlled melting of alumina in an electric arc furnace. White fused alumina is iron-free, ultra pure and extremely hard. White fused alumina is produced by fusing calcined alumina in an electric arc furnace under carefully controlled conditions. The material produced is white in color, dense and has predominantly large crystals of alpha alumina. Ingots are crushed, ground, and precision screened in our new sizing plant to obtain very consistent sized fractions. Magnetic iron from crushing is removed by rare earth magnets to ensure very low levels of iron in the finished products. Close sized fractions are available or precision blended to specification. This process ensures a very consistent sizing from coarse to fines which is critical in many applications. White aluminum oxide has white color and a little higher hardness and toughness comparing with the brown one. The grinding tools made of this material are suitable for fine grinding of high carbon steel, high-speed steel and stainless steel, abrasive powder of finer grit size, can also be used for precision casting and high-grade refractory.
White Fused Aluminium Oxide (WFA)� is widely used for Abrasive Tools, Sandblasting, Polishing, Surface Preparation. Our WFA is a hard, dense and iron-free material with highest purity, hence is an ideal abrasive material. It also has above 95% Al2O3 content, high degree of whiteness, extreme hardness and a wide range of precise grit sizes.
Quartz is the second most abundant mineral on Earth's crust. A wide variety of high grade Quartz that we are offering is appreciated for its resistance against mechanical and chemical weathering. Quartz (Silica SiO2) is the most common mineral in the Earths crust. Quartz is found in sandstones, pegmatites granites, and other igneous rocks. It is hard, chemically inert and has a high melting point, attributable to the strength of the bonds between the atoms and extremely resistant to weathering. Quartz used in many industries:- Quartz sand/grains in Glass Industry, Ceramics Industry, Paint industry, Oil well drilling. A wide variety of high grade Quartz that we are offering is appreciated for its resistance against mechanical and chemical weathering. They are ubiquitous and durable. The offered Quartz is finely processed at our sophisticated production unit. We are a well-established Quartz Manufacturer, Exporter and Supplier from Rajasthan (India). We provide them in safe, industrial grade packing. Also, we can process bulk orders on request. Product Description KIRAN MINERALS - Price Of White Quartz Grits Grain From Bewar Rajasthan Kiran Minerals is interested in manufacturing, exporting and supplying a wide range of Quartz Grits & Quartz Powder in India, Vietnam , South Korea, Malaysia, Gulf & in USA. It is the most common rock-forming minerals. This range of Quartz Grits are manufactured at our high end manufacturing unit as per industrial guidelines and specifications. Uses of Quartz Grits & Quartz Powder Used In Engineering Quartz Stone & Quartz Slabs Plants Used as an abrasive in stone cutting and sandblasting. Used in oil drilling, glass grinding, fiber glass, solid surface, paint stripping, Micro graving and Micro blasting. Application uses of Quartz Grits & Quartz Powder Quartz slabs Tiles Abrasive Foundry Sand Ceramic Construction Industry Sanitary ware Ferro Alloys Ferro Silicon Ferro Chrome Oil drilling Artificial Granites Electronic Industry
Inspired by mid-century rugs, our polka dot rug has a soft, high shag pile. The all-over pattern is woven in black on a white background. Cleaning� : Do not wash. We recommend gently vacuuming this rug once or twice weekly with a brush attachment. Do not use an abrasive rotary brush head as this may damage to the rug. Stain Removal� : Wipe the stain carefully with a mixture of lukewarm water. Absorb excess liquid with a dry microfiber cloth.
Brown fused alumina is manufactured in electric arc furnace, using bauxite as raw material. High hardness and toughness, it is an important raw material of abrasive and refractory industries. It can be used for belt, ceramic, coated, high-grade, and organic abrasives. The product can be used as abrasive and refractory material. The abrasive tools made by brown fused alumina are suitable for grinding carbon steel, normal alloy steel, malleable cast iron and hard bronze, etc. Brown fused alumina can also be used for making fine quality refractory. Brown aluminium oxide has high toughness. Micro hardness is 1800-2200kg/mm2, abrasive articles made of it are suited for grinding metals of high-tensile strength such as steel, annealed malleable iron and hard high-class refractory products. The application scope of brown fused alumina: 1. For abrasive 2. For refractory materials 3. For sandblasting abrasive 4. For abrasion resistance ground 5. For producing mold of precision casting. 25kg/bag or 1ton/bag or as your requirements
WHITE QUEBRACHO CHARCOAL CHARACTERISTICS Alboreas Species: Hard and Semi-hard Woods. Elaboration: Traditional ovens Ignition Features: Caloric Power: Not less than 7500 Kca/Kg Maximum humidity allowed: 8% Fixed carbon: 75-80% Abrasive: 71%. Ash: 3% white color Volatile: 3.5 - 4.5%. Incandescent time: 4-5 hours. Uniform color. Sound: Metallic, does not spark or explode, burns with smokeless flame. Approximate dimensions: Specifications: 20 -60mm 20 -80mm 20- 150mm 40 - 150mm The Coal is packed in paper bags according to the customer's requirement. It is processed through sieves or packaging machines. Exported: In 40 HQ containers without pallets with no less than 20 tons.
Blasting abrasive material steel grit 1, factory price with good quality. 2, G10-G120 3, 0.2mm-2.5mm 1. Production specification: g10, g12, g14, g16, g18, g25, g40, g50, g80, g120 2. Chemical composition of cast steel grit: c 0.70-1.20%, mn 0.60-1.20%, si0.40-1.20%, s0.05%, p 0.05% 3. Gp: 42-50hrc (399-509hv). Gl: 56-60hrc (620-713hv). Gh: 63-66hrc (795-889hv). 4. Microstructure: tempered marten site high strength, durable, ervin life: cast steel grit: 2500 cycles.
Steel shots High class metallic abrasives sae shots and grits Chemical composition:-c .8-1.2%, mn.8-1.2%, si.5%min, s.05%max, p .05%max Density:-7.4gm/cc, hardness hrc 40-50, .Quality control is ensured through process supported by well equiped laboratory & experienced professionals. Packing=25 kgs bag
NMCO offers 4 grades of Potassium Feldspar: Product - Feldspar Ore Specification Grade A : ( K2O > 11%), ( Na2O < 3%), ( Iron Oxides < 0.3%) Grade B : ( K2O - From 9% To 11%), ( Na2O < 3%), ( Iron Oxides < 0.5%) Grade C : ( K2O - From 7% To 9%), ( Na2O < 3%), ( Iron Oxides < 0.7%) Grade D : ( K2O - From 5.5% To 7%), ( Na2O < 5%), ( Iron Oxides < 1%) Shipping mode - Containerized or Bulk Packing - As per client requirement Monthly capacity - 15,000 tons Definition: feldspar is a generic term for a wide range of metals consisting mainly of aluminum silicate, rich in sodium, potassium, calcium or barium Properties and uses Natural properties: Feldspar in general light colors and often are of white or pink or orange orange or green If it is green, it is known as Amazonian, which is semi-transparent and has a glassy appearance and waxing and glaze ceramic As a property of cracking, the Feldspar the ability to break the mass with surfaces The feldspar glitter shows clear schizophrenia at two levels intersecting at angles of equality or convergence (90 degrees). The natural properties of Feldspar are: - Crystal shape: Single or triangular - Color: Orange or Orange Orange - Scratch: White, yellow or pink - Hardness: 6 - Specific density: 2,54 - 2,76 Feldspar is used in many industries, mainly the manufacture of glass, ceramics and abrasives, as well as used as fillers in the manufacture of plastic, paints and rubber and recently began to use feldspar in the manufacture of electrical insulators and plastic domes. Technical specifications: We have different types of feldspar, whether or not, or veins, where we have the raw materials third grade total potassium oxide and sodium oxide to 14%, and our mines are characterized by the quality of raw material and contain a large reserve
Copper slag is a by-product of copper extraction by smelting. During smelting, impurities become slag which floats on the molten metal. Copper slag is mainly used for surface blast-cleaning. Abrasive blasting is used to clean and shape the surface of metal, stone, concrete and other materials. In this process, a stream of abrasive grains called grit are propelled toward the workpiece. Copper slag is just one of many different materials that may be used as abrasive grit. Rate of grit consumption, amount of dust generated, and surface finish quality are some of the variables affected by the choice of grit material. Internationally the described media is manufactured in compliance with ISO 11126-3[4] The blasting media manufactured from copper slag brings less harm to people and environment than sand. The product meets the most rigid health and ecological standards. SIZES AVAILABLE 0.50 MM TO 1.50 MM 0.50 MM TO 2.50 MM 0.50 MM TO 3.00 MM 0.50 MM TO 4.00 MM 0.10 MM TO 5.00 MM
Polyester fine filler including white hardener. For filling any pores and unevenness that may still be present in the filler filler. Creates an absolutely smooth and pore-free surface. Fine filler with particularly smooth pulling properties; can also be used as a filler filler due to its thixotropy. The fine-grained abrasion enables low abrasive consumption. Super easy to sand. No discoloration thanks to the white hardener. Weight n/a Size 250g, 500g, 1kg
Size 500g 1 kg Polyester filler including white hardener. For filling deep uneven areas, even on vertical surfaces. For filling any deep pores and uneven areas that may still be present. Creates a relatively smooth and pore-free surface. Filler with very good pulling properties. The fine-grained abrasion enables low abrasive consumption. Super easy to sand. No discoloration thanks to the white hardener
General Specification * Well Dressed and Cleaned * Drained from Excess Water * Cooled Down and Frozen Fresh * No Bad Smell * No Black Spots * No Excessive Blood or Blood Stains * No Bruise * No Chemical Burns * Outer Yellow Skin Off * White Color * Strictly Halal slaughtered * Broken Bones Less than 1% * Moisture Less than 3% Frozen Temperature: - Blasted at: minus 40 degrees Celsius - Storage at: minus 20 degrees Celsius. - Temperature during Transportation: minus 18 degrees Celsius We package in 20kg carton boxes, each box contains 5kg polybags x 4. Customized packaging of all other sizes. are offered, and we also provide labels for buyers. We load 27MT per container 40FT.
Dear Sir/Mme, Thanks for the interest in our quality Fresh & Frozen Chicken Feet & chicken Paws Features: Chicken Feet - Washed and clean. - Without yellow skin. - No feathers. - No bad smell. - No blood. - No bruises. - No black pads. - No traces of carved deep wounds. - No ammonia burns. - Broken bones: under 3%. - Moisture content: less than 5%. - Weight per piece is 45-55g - Length per piece 13-15cm *Specifications:* Chicken Paws - White skin - No broken bones 0% - Outer yellow skin off - Well cleaned and fresh - No bruises - No black pads or ammonia burns - No bad smells - No excessive blood or blood stains - Moisture content is less than 3% - Weight per piece is 35-45g - Length per piece 10-12cm - Drainage: 0 to -5�°C for 8 hours. - Blasted at: -40�°C. - Storage at: -18�°C -Packing: 20kg Carton Boxes Containing 5kg poly bags X 4 in each MOQ: Negotiable Leadtime: Negotiable Payment Options: L/C,T/T, EXW rates. Best Regards.
Polarization: 99.80% degrees min Ash by electrical conduct: 0.04% max (on dry weight basis) Ash content: 0.04% max Moisture: 0.04% max ICUMSA 45 RBU: Max (Brazil S.G.S scale) Solubility: 100% dry and free flowing Color: Sparkling white ICUMSA Maximum 45 attenuation index units (ICUMSA method #: 4-1978) Radiation: Within CS-137 of 50 BQ per Kg Granulation: Fine crystal Crop: Latest Magnetic particles: Mg/Kg 4 max SO2 mg/kg 20 max Sulfur Dioxide: 20 Mg/Kg min Sediments: None Smell: Typical and specific for sugar Reducing sugar: 0.05% Max by weight HPN Staph Aureus not detected in 1 gram Maximum AS: 1 P.P.M. Maximum PB: 1 P.P.M. Maximum CU: 3 P.P.M. Substance: Solid Crystal Tolerance: 5% (+/-) CHICKEN PAWS SPECIFICATIONS Quality: Grade A Frozen Chicken Paws Process: BQF Cut at the Level of the joints Meaty and Coating of Normal Fat Average Weight Per Piece: 35 â?? 45 grams Average Length Per Piece: 09 â?? 12 cm Processing: 100% Fresh and Frozen White Skin Shelf Life: 24 months Frozen Requirements: Blast Frozen at -40�°C Stocked and Stored: -18�°C During Transportation: -18 �°C Ice Content: Less Than 0.3% Outer Yellow Skin Off Well Dressed and Cleaned No Black Pads or Ammonia Burns No Bad Smells, No Excessive Blood or Blood Stains No Excess Water No-Broken Bones Fresh and Hard Nail * No Bruises No Feathers * No Hairs Moisture Contents Less Than 2% Production Age: Not More Than 60 days from the shipping date Chemical Burns Presence: No Chemical Burns Black Spot: Less than 1% Broken Bone: Less Than 1% Antibiotics: Presence Not Allowed Pathogenetic Organisms (Including Salmonella): Not Allowed Foreign Substances: Not Allowed * Remanants of Feathers: Not Allowed Frozen Requirement Drainage: 1�°C - 5�°C For 8 hours Moisture Content Less Than 1% Blasted at: -40�°C SIF code: 1, 103, 87, 121, 1001
Aluminium oxide is used in blasting cabinet or blast rooms, in an area where you can recycle. It is used to shot blast chassis components, alloy wheels, brake callipers, small ferrous components. Aluminium Oxide is used in the aero space industry . Aluminum oxide is used in boned abrasives or refractory or coated abrasives. Barmac/angular Available in pink/brown/white. F12-F220 0-1mm 1-3mm 3-5mm 5-8mm P12-P220
Products Name: Pure Aluminum A7 Ingot 99.9% Chemical Composition: Al Weight: 20/25kg Al (Min): 99%-99.9% Appearance: silvery white Aluminum ingot for remelting is produced by molten salt electrolysis method using alumina and cryolite. Products meet the national standard GB/T1196-2002. The surface of ingot is clean and smooth. Item: A7 Aluminum ingot 99.7 high quality Standard: GB/T 3190-2008 JIS H4040:2006 JIS H4001:2006 ASTM B221M:2006 ASTM B209M:2006 ISO 209:2007(E) EN 573-3:2003 etc. Material: 1000 Series Size: Thickness:0.1-200mm,or as requiredWidth:0.1-2000mm,or as required Size can be customized according to customer needs Surface Bright, polished, hair line, brush, sand blast, checkered, embossed, etching, etc. Application: mainly used for melting ingot; discontinuous melting with scrap; easy control and operation; fast melting; Used for industry such as automobile, pinning and weaving, electron broadly and so on . Export to: Worldwide etc. Package Standard airworthy export packaging: wooden pallets with plastic protection or according to customer requirements Packaging Details: Packing 25KG/INGOT, 1000KG or 1050KG/bundle, or as your requirement AL â?¥ Fe Si Cu Ga Mg Zn others Total 99.9 0.07 0.05 0.005 0.02 0.01 0.025 0.016 0.01 99.85 0.12 0.08 0.005 0.03 0.02 0.03 0.015 0.15 99.7 0.2 0.1 0.01 0.03 0.02 0.03 0.03 0.3 99.7 0.2 0.12 0.01 0.03 0.03 0.03 0.03 0.3 99.6 0.25 0.16 0.01 0.03 0.02 0.03 0.03 0.49 99.5 0.3 0.22 0.02 0.03 0.05 0.05 0.03 0.5 99 0.5 0.42 0.02 0.05 0.05 0.05 0.05 1
Hexamethylene or methenamine is a heterocyclic organic compound with the formula (CH2)6N4. This white crystalline compound is highly soluble in water and polar organic solvents. It has a cage-like structure similar to adamantane. It is useful in the synthesis of other chemical compounds, e.g., plastics, pharmaceuticals, rubber additives. It sublimes in vacuum at 280 �°C. Application The dominant use of hexamethylenete tramine is in the production of powdery or liquid preparations of phenolic resins and phenolic resin moulding compounds, where it is added as a hardening component. These products are used as binders, e.g. in brake and clutch linings, abrasive products, non-woven textiles, formed parts produced by moulding processes, and fireproof materials. Medical uses As the mandelic acid salt (methenamine mandelate) or the hippuric acid salt (methenamine hippurate), it is used for the treatment of urinary tract infection. Histological stains Methenamine silver stains are used for staining in histology, Solid fuel Together with 1,3,5-trioxane, used by campers, hobbyists, and relief organizations for heating camping food. Reagent in organic chemistry Hexamethylene is a versatile reagent in organic synthesis. It is used in the Duff reaction (formylation of arenes), the Sommelet reaction (converting benzyl halides to aldehydes), and in the Delepine reaction (synthesis of amines from alkyl halides). Explosives Hexamethylene is the base component to produce RDX