We are glad to propose 500 MT of stain less steel mill scale. Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products. At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel. The recovery ratio after melting in furnace for the most valuable alloy elements is: - Ni: 3.5 - 4.5% - Cr: 6-8% From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows: Waste code: 10 02 10 The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers. Chemical analysis of the material is available on request.
We are proposing about 2000tons of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag - European Code: 19.12.01 - Basel Code: B1010 - HS Code: 2619.0020 - Quantity: 2000 tons currently available - Monthly quantity: 500-1000 tons depending on production - Size: 350 1200 mm - Fe content: from 77 to 86% - C content: above 2,5-3% - Bulk density: 2,8-3,4 tons/m3 - Loading type: loose in 20 (26-27 tons on average) The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact us
This Cast Iron slag is a by-product derived from the production of thermal insulating products. The byproduct is a ferrous slag which can be utilised in an electric arc furnace to produce crude steel. Physical Description On visual inspection, it appears to be made up of irregular shapes. Dimension: 500mm -800mm Chemical Composition Its chemical composition is homogeneous and stable with Fe contents in the range of 90 +/- 5% and P contents < 0.6% S around 0.15% and C% around 3.5%. Packing: Loose in container Loading: in 20 Container For further information, please feel free to contact us.
Mill scale, is formed on the outer surfaces of plates, sheets or profiles when they are being produced by rolling hot iron or steel billets in rolling or steel mills. It looks like a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in color. Being produced during the reheating, conditioning and hot rolling operation for the production of steel articles, the mill scale initially adheres to the steel surface and protects it from atmospheric corrosion, provided no break occurs in this coating. From the chemical and physical analysis performed on the scrap, and according to the european environmental rules, the material has been classified as a special non dangerous waste, listed in green list In particular the mill scale can be classified as follows: Einecs (european commission no.): 266-007-8 Waste code: 10 02 10 Basel code: b 12 30 Hs code: 2619.00
We are proposing about 1000 1200 Mt/ton monthly of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag : 1. >85% Fe Average 600mm Max Fraction 2. >78% Fe Average 20-300mm Fraction The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact
Waste Specification: European Classification: E46 EWC Code: 19.01.02 Basel Code: B10 10 The material is loose steel scrap processed through an incinerating plant for domestic waste followed by magnetic separation, fragmentized into pieces and consisting partly of tin coated steel cans. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. Due to the scrap dimensions and the material conditions, this particular scrap, should be carefully evaluated first, by the end users, to confirm its adequate recovery ratio and its suitability to be re-melted in the electric arc furnace. Please feel free to contact us for further details
Desulphurisation Slag is an iron slag derived from the desulphurisation skimming process. This material is an iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si), but has a stable chemistry with 75 -80% chemistry. The level of Fe% in the slag has been estimated by water displacement test. This material con offer competitive advantages respect other metal scraps: Price; Stable Chemistry; The material can be loaded loose in 20 heavy duty container. For further details feel free to contact us.
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.
The Tire derived Steel or Tire Wire Scrap is a light melting scrap obtained during the shredding and granulation process of used tires. Generally 10% - 20% of the weight of an old passenger car tyre usually consists of steel. An average shredding plant produces about 100-200 MT of steel tyre wire and its quality can vary according to technology, storing and management systems adopted by the producing plants. We can provide tire wire scrap that still contains up to 20% rubber/fiber. This percentage is detected by manual separation test. The material can be loaded loose in 40 HC container. For further details, please feel free to contact us.
The Aluminium Incinerated scrap is the by-product derived from the reprocessing IBA Incinerator bottom ash). It can be classified as follows: Basel code B1010. EW Code: 17 04 02. With a low melting point at 660'C, on visual inspection, aluminium can be found as melted and re-solidified particles or rocks. This happens to aluminium foil that is converted into small droplets during the incineration process. Some larger and thicker aluminium packaging items can still be partially recognised as they retain their shape. The heterogeneous nature of the processed material is due to the diversified conditions present in the combustion chamber, (some relatively cooler regions in the furnace). The stock can contain all kind of aluminium packing. We can currently provide this material in three different fractions and with different aluminium content: 3-8 mm split in two different qualities: 65% ± 3% Al 85% ± 3% Al 8-16 mm: about 70% ± 3% Al 16-60 mm: about 80% ± 3% Al The material contains minor impurities typically stones, ash, glass. Such components are inherent and adhere to the scrap surface. The total impurities can be sorted, but not fully removed. The collected stock is stored in warehouse on cemented flooring. It can be loaded loose in 20' Feet heavy duty container.
We offer a wide plethora of Zinc in many forms including LME registered and non registered Special High Grade Ingots and Jumbos, cathodes, dust, foil, granules, powder, pieces, anodize activated powder, shot, and a mossy form. Zinc is a bluish-white, lustrous metal. It is brittle at ambient temperatures but is malleable at 100 to 150°C. It is a reasonable conductor of electricity, and burns in air at high red heat with evolution of white clouds of the oxide. Plating thin layers of zinc on to iron or steel is known as galvanizing and helps to protect the iron from corrosion.
We hold immense expertise in making available Copper in many forms including LME registered and non registered cathodes, billets, rods, cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire, insulated wire, mesh and “evaporation slugs”. Copper is one of the most important metals. Copper is reddish with a bright metallic lustre. It is malleable, ductile, and a good conductor of heat and electricity (second only to silver in electrical conductivity). Its alloys, brass and bronze, are very important. Monel and gun metals also contain copper. The most important compounds are the oxide and the sulphate, (blue vitriol
Steel
We are able to supply Tin in many forms including LME registered and non registered, ingots, slabs, bars, foil, granules, powder, anodized activated powder, shot, wire, sticks, ingots, and “mossy tin”. Tin is a silvery-white metal, is malleable, somewhat ductile, and has a highly crystalline structure. The element has two colours, with a cubic structure which changes at allotropic forms. On warming it is grey, the ordinary form of the metal. When Tin is cooled below 13.2°C, it changes slowly from white to grey or tetragonal structure. This change is affected by impurities such as Aluminium and Zinc, and can be prevented by small additions of Antimony or Bismuth.
We put forward a high quality of assortment of Nickel which is available in many forms including LME registered and non registered cathodes, cut cathodes, briquettes, pellets, disks, shots, granules, foil, powder, flakes, sheet, wire, mesh, spheres, “evaporation slugs”, and rods. Nickel is a silvery white metal that takes on a high polish. It is hard, malleable, ductile, somewhat ferromagnetic, and a fair conductor of heat and electricity
We are engaged in making Lead available in several forms including LME registered and non registered 99.97% and 99.99% as well as secondary ingots, foil, granules, powder, rod, shot, sheet, and wire. Lead is a bluish-white lustrous metal. It is very soft, highly malleable, ductile, and a relatively poor conductor of electricity. It is very resistant to corrosion but tarnishes upon exposure to air. Alloys include pewter and solder.
Disposable Plates, Cake, Tea, Swimming Goggles, Diving Mask, Arecanut Palm Leaf Plates And Cups.
Hoodies and jackets, winter shirts, cashmere sweat shirts, wool jackets, leather products like working gloves, welding gloves, driving gloves, industrial gloves, bike gloves, leather aprons, leather belt, arm covers, safety jackets, motor bike jackets, water proof leather, fire proof leather, waterproof leather gloves, fireproof leather jackets, nubuck leather, crust leather, finished leather, buffalo leather, suede leather, cowhide leather, goat and sheep leather, lederhosen, caps, hats, beanies.Manufacturing and exporting
Product name : Food Serving Tray, Material : ASH wooden, Size : Custom size accepted,
LEAF PALTES for food serving , pure natural
