This lighting fixture designed for sliding installation is more convenient, and this led linear light adopts stainless steel base, so that the intensity of this led linear luminaire can achieve IK10. This linear luminaire has high transmittance milky diffuser and high lumen out put SMD2835 LED chips, so that the luminous efficiency of this led batten light fitting can achieve 125lm/w. The safety hooks design of this led� light fitting is more convenient and safe for installation. The clip-fixed backup battery design of this led linear light fitting makes the maintenance and replacement more easier. And the� emergencny function enable the led batten light � to operate continuously for more than 3 hours in emergency situations. It's very practical. Lighting solutions service: Lighting and circuitry design, DIALux evo layout, Agi32 layout Model Number: ZL-NSBLP60-5FT-CES Color Temperature(CCT): 3000/4000/6000K Input Voltage(V): AC 220V(± 10%) Color Rendering Index(Ra): 80 Support Dimmer: Yes Lifespan (hours): 50000 Working Time (hours): 50000 Length: 5ft Beam angle: 120 Degree
This machine is an indispensable tool for railway maintenance, construction and emergency repair operations. It uses a hollow drill bit, fast clamping, accurate positioning, fast drilling, simple operation and safety use.The rail clamping device has self-locking function, and high drilling precision. The hollow drill bit is used, and special twist drills below 13.5 can also be clamped according to needs. It has automatic water supply function when drilling, and is suitable for maintenance, emergency repair and overhaul operations in public works departments. Item Petrol Engine Rail Drilling Machine Dimensions (L x W x H) (mm) 650*230*250mm Place of Origin China Model NZG-31Internal Combustion Steel Rail Drilling Machine Internal Combustion Engine Honda Gasoline Engine GX35 Rotate Speed without load 270r/min Rate of Power 1.2KW Driling Diameter 31, 13.5, 9.8 Drilling Time 25s Weight 17KG
Lithium battery powered Rail bolt wrench machine (model: LJ-LDB171X) is composed of host, control system, battery system and rail traveling part. The utility model has the advantages of compact structure, light weight, flexible assembly and disassembly, convenient use and no exhaust emission. It can be transported separately, which is convenient for single person to carry on site. The weight of the separated part is less than 15kg. It is applicable to the laying, maintenance and emergency rescue of railway, and is specialized in various railway bolt operations Specification Model NGM-4.4II Type Rail Profile Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 1480*470*810mm Engine Two-stroke petrol engine/4.4KW Main shaft rpm 4670r/min Bolt screwing flat grinding wheel 125*65*M20 Grinding head angle of inclination 90 ° Grinding head stroke 45 mm Total weight 61kg
This machine is powered by the M165 two-stroke petrol engine imported from Spain. It is a small machine used for forming and grinding the rail head welding joints and surface repairs. It is suitable for rails of 43~75kg/m. The special diaphragm carburetor make sure the engine does not stall after turning 90�°, and the output torque is stable without power attenuation, thus ensuring the precision of rail grinding. Specification Model NGM-6.0 Type Rail Profile Grinder Material Stainless Steel Dimensions (L x W x H) (mm) 1410*500*850mm Engine 2 stroke petrol engine M165 Power 6.0kW Grinding stone speed â?¥3900r/min Grinding stone inclination 0~90�° Grinding stone feeding stroke 42mm Grinding stone specification �?150x�?55x70mm Fuel tank volume 4.5L Profile wheel span 1000mm Feed adjustment accuracy 0.125mm Weight 60kg
This machine is powered by the M165 two-stroke petrol engine imported from Spain. It is a small machine used for forming and grinding the rail head welding joints and surface repairs. It is suitable for rails of 43~75kg/m. The special diaphragm carburetor make sure the engine does not stall after turning 90�°, and the output torque is stable without power attenuation, thus ensuring the precision of rail grinding. Specification Model NGM-6.0 Type Rail Profile Grinder Material Stainless Steel Dimensions (L x W x H) (mm) 1410*500*850mm Engine 2 stroke petrol engine M165 Power 6.0kW Grinding stone speed â?¥3900r/min Grinding stone inclination 0~90�° Grinding stone feeding stroke 42mm Grinding stone specification �?150x�?55x70mm Fuel tank volume 4.5L Profile wheel span 1000mm Feed adjustment accuracy 0.125mm Weight 60kg
Lithium battery powered Rail bolt wrench machine (model: LJ-LDB171X) is composed of host, control system, battery system and rail traveling part. The utility model has the advantages of compact structure, light weight, flexible assembly and disassembly, convenient use and no exhaust emission. It can be transported separately, which is convenient for single person to carry on site. The weight of the separated part is less than 15kg. It is applicable to the laying, maintenance and emergency rescue of railway, and is specialized in various railway bolt operations Specification Model LJ-LDB1701X Type Lithium Battery Torque Wrench Material Stainless Steel Dimensions (L x W x H) (mm) 1100*700*450mm Type Battery powered rail bolt wrench Rated voltage (DCV) 24-48 Max. torque 3000 N.m Motor speed (RPM) 0-3000 optional Impact frequency (BPM) 0-5000 optional Battery pack capacity (ah) 24-48 Operating temperature range (-40 ~ 50 â??) Operating range m6-m30 Torque control adjustable and controllable Weight 22kg
Ceramic Fiber Blanket Introduction Rosewool ceramic fiber blanket has excellent specialties of low thermal conductivity, good heat stability, thermal shock resistance and tensile strength, good thermal insulation, fire proof and noise reduction. It is widely used in power generation, iron and steel, aluminum/n-ferrous metals, glass, ceramics, aerospace, super alloys, petrochemical, semiconductors, cement, automotive, domestic appliances etc. Temperature level is 1100-1430 (2012 --2600 ). Ceramic Fiber Blanket Application 1. Linings and back-up insulation for all types of furnaces, heaters and kilns 2. External insulation such as boiler, turbine, duct and piping, precision casting shell etc 3. Vehicles and domestic appliance insulation 4. High temperature sealing material such as ladle lid, duct connecting part etc 5. Noncombustible materials for building 6. High temperature gas filtration material, high temperature part sound absorbing material 7. Pressure and cryogenic vessel fire protection 8. Furnace repairs Rosewool Company Supply Ceramic Fiber, Rock Wool, Calcium Silicate Products, Glass Wool, Airgel Felt, Airgel Board With 30+ Years Of Experience. Contact Us For The Best Quotation!
Rail Clamp The Rail Clamp is an innovative temporary rail joint clamp used prior to welding and to safeguard rail defects prior to repair. The Rail Clamp has been engineered to eliminate many of the disadvantages of other traditional rail clamp designs and provides enhanced performance under all conditions of use. The Rail Clamp design is radically different to the legacy design and guarantees a positive pre-torque angle so as the bolt is tightened the bolt holes remain aligned, eliminating the risk of bent bolts. We test have proved that bolts remain straight even at twice the recommended torque. · Allows suction jars to be attached to stand rail · One rail clamp holds one canister · Rail can hold up to four rail clamps and canisters Specification Model LJ-JJQ-C Type Rail Clamps Material Stainless Steel Dimensions (L x W x H) 335mm*175mm*42mm Application Rail Type 43,50,60kg
Rail Clamp The Rail Clamp is an innovative temporary rail joint clamp used prior to welding and to safeguard rail defects prior to repair. The Rail Clamp has been engineered to eliminate many of the disadvantages of other traditional rail clamp designs and provides enhanced performance under all conditions of use. The Rail Clamp design is radically different to the legacy design and guarantees a positive pre-torque angle so as the bolt is tightened the bolt holes remain aligned, eliminating the risk of bent bolts. We test have proved that bolts remain straight even at twice the recommended torque. · Allows suction jars to be attached to stand rail · One rail clamp holds one canister · Rail can hold up to four rail clamps and canisters Specification Model LJ-JJQ-C Type Rail Clamps Material Stainless Steel Dimensions (L x W x H) 335mm*175mm*42mm Application Rail Type 43,50,60kg
Double Side Rail Hole Chamfering Kit The double chamfer is used for chamfering the holes on the waist of railway rail. The structure of the bilateral chamfering device: It has a door frame, the left and right holder through a set of four bar linkage hinge, and equipped with upper locking lever handle, install left axle shaft sleeve of the bottom of the left bracket, left axis right side is equipped with disc blade, left left end shaft with a ratchet wrench, right shaft are installed in the shaft sleeve from the lower pole of the right holder, the right shaft suits a compression spring, right left end shaft is equipped with the disc blade, The right end of the right axle is fitted with a ratchet wrench. The double-sided chamfering device has the advantages of simple structure, convenient operation and high working efficiency. The blade is disk-shaped, the blade on the whole circumference is sharp and wear-resistant, and the service life is long. Specification Model LJ-DJQ-S Type Rail Chamfering Tool Material Stainless Steel Dimensions (L x W x H) 40*15 cm Chamfer Diameter �?31-�?32 Chamfering Size 1�?45�°, 2.5�?45�° Application 43kg/m,50kg/m,60kg/m rail Weight 2.8KG
Double Side Rail Hole Chamfering Kit The double chamfer is used for chamfering the holes on the waist of railway rail. The structure of the bilateral chamfering device: It has a door frame, the left and right holder through a set of four bar linkage hinge, and equipped with upper locking lever handle, install left axle shaft sleeve of the bottom of the left bracket, left axis right side is equipped with disc blade, left left end shaft with a ratchet wrench, right shaft are installed in the shaft sleeve from the lower pole of the right holder, the right shaft suits a compression spring, right left end shaft is equipped with the disc blade, The right end of the right axle is fitted with a ratchet wrench. The double-sided chamfering device has the advantages of simple structure, convenient operation and high working efficiency. The blade is disk-shaped, the blade on the whole circumference is sharp and wear-resistant, and the service life is long. Specification Model LJ-DJQ-S Type Rail Chamfering Tool Material Stainless Steel Dimensions (L x W x H) 40*15 cm Chamfer Diameter 31-?32 Chamfering Size 145°, 2.5 45° Application 43kg/m,50kg/m,60kg/m rail Weight 2.8KG
Railway Crow Bar It is for situations such as these that the jim-crow comes into its own. The jim crow was slotted over the rail about four or five sleepers away from the offending joint.and the screw tightened until it engaged with the edge of the rail. Then tightened the screw a further half-turn - thus bending the rail slightly.This process was repeated, moving the jim crow one sleeper nearer the joint each time and each time adding one more half-turn. This introduces a gradually increasing curve to the rail as it nears the joint.If you compare these two pictures with those showing the kinks above, you can see the difference. The amount of bend can be tailored to suit each location - and if it turns out that have made the curve too severe, the jim crow can be slotted on the opposite way round and tightened up to ease the curve. Specification Type Crowbar Railway Material Steel Dimensions (L x W x H) 1500mm, 1800mm Place of Origin China Hubei Brand Name Linkage Item railway crowbar Brand Name Linkage Application Wrecking & Demolition, DiggingChiseling Tip Type Chisel End, Rolled Nail Puller for High Leverage, Heeled Pinch End Length 1500mm, 1800mm Weight 6 KG
Hydraulic Railway Track Jack It is new type equipment that is used on the railway line's maintenance and repairing. The most important feature of this machine is that is a dual-purposed machine what meet the needs of the lifting work of the line, as well satisfy lining operations. Hydraulic Track Lifting and Lining Tool is mainly composed of: power part, operating mechanism, body, running gear, landing gear, hook rail device, starting device, dialing device, lower guiding device, lower track, etc. Hydraulic Track Lifting and Lining Tool is specially used for the railway track maintenance. It is used for the track lifting and lining. It has features with simple and compact structure, simple and flexible operation, easy maintenance,fast and reliable performance when go up and down the track Specification Model YBD-245A Type Hydraulic Railway Track Material Stainless Steel Rated lifing force/ Rated lining force(kN) 245/145 Maximm lifting Quantity/ lining quantity(mm) 135/95 Weight(kg) 23
Place of Origin Hubei, China Type Rail switch grinding machine Material Stainless Steel Dimensions (L x W x H) (mm) 2100*1120*1030mm Brand Name Linkage Product name Rail switch grinding machine for track maintenance function Rail switch point grinding Engine Honda GX270 Petrol engine Grinding wheel speed: â?¥3600r/min Feed adjustment accuracy: â?¤l0mm Weight â?¤117kg Rated power: 5.1kW Grinding wheel feeding stroke: â?¥80mm Grinding wheel rotation angle: â?¥30�° NCM-5.1 frog and switch grinding machine is specifically designed for grinding operations through switch and crossings and either side of the rail head. The grinding device of the machine can be tilted by 30�° from the vertical direction to the left and right, and the position of the grinding wheel can be adjusted along the vertical and horizontal directions So that the grinding device of the machine can work very accurately in the narrow space between the rails. The machine adopts the pull rod transverse feed mode, which is easy for the operator to grasp the feed force and improve the grinding quality and efficiency. It has the characteristics of precise turning and positioning at any position and angle of the turmout rail head.
Place of Origin Hubei, China Type rail profile grinding machine Material Stainless Steel Dimensions (L x W x H) (mm) 1410*500*850mm Brand Name Linkage Product name rail profile grinding machine Profile wheel span: 1000mm Engine 2 stroke petrol engine M165 Grinding stone speed: â?¥3900r/min Grinding stone feeding stroke: 42mm Fuel tank volume: 4.5L Feed adjustment accuracy: 0.125mm Power: 6.0kW Grinding stone inclination: 0~90�° Grinding stone specification: 150*55*70mm NGM-6.0 Internal Combustion Rail Profile Grinding Machine This Rail Profile Grinding Machine is powered by the M165 two-stroke petrol engine imported from Spain. It is a small machine used for forming and grinding the rail head welding joints and surface repairs. It is suitable for rails of 43~75kg/m. The special diaphragm carburetor make sure the engine does not stall after turning 90�°, and the output torque is stable without power attenuation, thus ensuring the precision of rail grinding.
NGM-5.1 Rail Profile Grinding Machine This machine is mainly used for forming and grinding operations of railway rail welding joints and rail surface repairs. The development and application of the CNC feed unit realizes the intelligent control of the grinding wheel feed. Significantly improve the profiling accuracy and polishing efficiency. BENIFITS â?? Angle of the grinding head is set using an adjustment wheel, lowering/raising of the grinding stone is electrically contlled â?? Equipped with spark protection device â?? Equipped with electric control system prevents over grinding by limiting the lowering of the grinding stone â?? Grinds the whole head of rail in one single operator, no need to turn the machine or to handle it Specification Model NGM-5.1 Type Rail Profile Grinding Machine Material Stainless Steel Dimensions (L x W x H) 1500 * 450 * 750 mm Engine HONDA GX270 Power 5.1 kW Grinding wheel specifications �?125x65 mm Feeding accuracy 0.1 mm Turning angle of grinding stone �±90�° Spindle revolution 4100r/min Grinding stone feeding stroke 42 mm Profile wheel span 1000 mm Weight 100 kg Weight of supporting rod 14 kg
Place of Origin Hubei, China Type Other Material alumunium Dimensions (L x W x H) (mm) 1900*1200*2500mm Brand Name Linkage Product name automatic rail tamping machine Usage automatic rail tamping machine Application automatic Hydraulic rail tamping machine Standard crcc Quality Control iso Certificate CE Warranty 1YEAR Customize yes Other name track ballast tamping machine YD-22III Smart rail tamping machine unit is a renewal product developed by our factory with new material and new technology. It has collected the tamping experience of users at home and abroad. It can do tamping works not only on the ballasted track of concrete sleeper type II and III in China, but also on various kinds of concrete sleepers and steel sleepers in foreign countries.This machine is suitable for tamping operation of different types of rails and concrete sleeper line after large and medium repair and sieving operations, and also suitable for tamping operation of ballast on newly built track bed. The equipment has superior performance, reasonable structure, safety and reliability, and high working efficiency. It fully meets the needs of railway ballast tamping operation
NQGâ??5.1 Rail Cutting Machine To furnish the varying desires of our customers, we are immersed in offering a world class consignment of Abrasive Rail Cutter. Abrasive Rail Cutter is suitable for cutting upto 60 Kg. 110 uts Rails. the machine has features of fast cutting speed, high utilization rate of cutting discs, high quality of cutting profile, convenient operation, easy motion and safe use. the machine comprises of petrol driven engine, integrated with a cutting unit fitted with an abrasive disc. Place of Origin Hubei, China Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 800*560*500mm Brand Name Linkage Engine GX270 petrol engine 5.1KW Specification of cutting disc 400*32 *4mm Cutting disc no. of revolutions 3320 r/min Linear speed of cutting disc 70m/s Cutting accuracy Verticalityâ?¤0. 4mm, flatnessâ?¤0.3mm Cutting time 2 min ( cut off 60kg/m rail) Weight 50kg
NQG 5III Internal combustion rail cutting machine is suitable for cutting rails of 43kg/m 75kg/m . The quality of cutting section meets the requirement of railway industrial standards. Its a necessary tool used in railway overhaul, maintenance and rush repairing operation. It has features of fast cutting speed, high utilization rate of thin grinding wheel, high quality of cutting section, easy operation, easy movement, safe use and wide application range etc. Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 670*600*510mm Brand Name Linkage Internal combustion engine HONDA GX200 Engine Power 4.8kW Engine Speed 3600r / min Thin grinding wheel (spindle) Spindle speed 3030r / min Specification (linear velocity) 400 * 32 * 4 (â?¥70m /s) Cutting time 60kg / m rail, â?¤120S Number of usage 50kg /m rail, use â?¥ 4 times Number of usage 2 60kg /m rail, use â?¥ 3 times Machine weight 39.5kg
Place of Origin Hubei, China Type Sleeper Drilling Machine Material Stainless Steel Dimensions (L x W x H) (mm) 420*500*1070mm Brand Name Linkage ENGINE 2 stroke petrol engine 1.42kW Max. drill diameter 20mm Drill speed â?¥350r/min Drill speed2 â?¤20s Weight 14kg NZMZ-20 Portable Sleeper Drilling Machine This machine is light-weight and easy to use and has the purpose of quickly drilling wooden sleepers ensuring precision andmaximum safety for the operator. It is composed of: * 4-stroke petrol engine with valves at the top and special lubrication to work on 360�°; * High-strength speed reducer gears lubricated by special TK3 grease that guarantees excellent lubrication and long life; * Ergonomic handle with throttle lever and engine safety lock; * Safety system with centrifugal clutch; * Possibility of inserting a lever able to rotate the drill bit in case of blockage; * Quick coupling / uncoupling spindle of the drill bit. Optionally we can supply: * Drill bit protection and drilling depth regulator ; * Trolley with 3 wheels for different types of track gauge; * SleeperDrill Bits.
