Product model: KY911 wear-resistant flux cored wire Product specifications: 1.2mm 1.6mm 15kg / box Post-weld hardness: HRC 65-70° Scope of application: It is suitable for high hardness and hard surface treatment of parts with high wear and high impact. It is suitable for surfacing welding with strong abrasion resistance. It has wide application range and high quality. Metal composition (%): C 3.00-6.00; Mn 2.00-3.00; B 5.00-8.00; Cr 20.00-25.00; Ni 2.00-3.00; Mo 2.00-3.00 Precautions: 1. Adopt DC reverse connection; 2. When welding, the flow rate of CO2 gas should be 20~25L/min; 3. The dry elongation of the wire should be controlled within the range of 15~25mm; 4. The temperature between the channels is recommended to be kept at around 300 °C; 5. Before welding, the weldment must be cleaned of rust, oil, moisture and other impurities. Precautions:   Precautions for use: The wear-resistant solder layer should generally be surfacing 1 layer. Because the number of layers is too much, the surfacing layer becomes brittle due to too high hardness and is easily broken after collision. Due to the high hardness, the welding wire has a cracking sound during the welding, and a small crack occurs, which is a normal phenomenon and does not fall off, and does not affect the service life.   We are a real wear-resistant welding consumables production factory, with a complete production process and inspection process, to provide you with high quality and cost-effective wear-resistant welding consumables.
Features for the Champion 100416 - Generator Tri-Fuel Technology Your 8000-watt portable generator operates on natural gas, propane, or gasoline, plus natural gas and propane hoses are included so the unit is ready to run on any fuel right out of the box. Electric Start Power up the 459cc Champion engine with the handy rocker switch, battery included. Intelligauge with CO Shield�® rack voltage, frequency, session run time, and total run time to monitor output and track maintenance intervals, plus the UL-recognized sensor uses an LED to indicate CO shutoff or fault. Powerful Gasoline: 10,000 starting watts and 8000 running watts, propane: 9000 starting watts and 7200 running watts, natural gas: 8750 starting watts and 7000 running watts and engine oil is included. SPECIFICATIONS Portable Generator Technology : Tri Fuel, CO Shield Gasoline Starting Watts: 10000W Gasoline Running Watts: 8000W Propane Starting Watts: 9000W Propane Running Watts: 7200W Natural Gas Starting Watts: 8750W Natural Gas Running Watts: 7000W Gasoline Starting Amps at 120V: 83.3A Gasoline Starting Amps at 240V: 41.7A Gasoline Running Amps at 120V: 66.7A Gasoline Running Amps at 240V: 33.3A Propane Starting Amps at 120V: 75A Propane Starting Amps at 240V: 37.5A Propane Running Amps at 120V: 60A Propane Running Amps at 240V: 30A Natural Gas Starting Amps at 120V: 72.9A Natural Gas Starting Amps at 240V: 36.5A Natural Gas Running Amps at 120V: 58.3A Natural Gas Running Amps at 240V: 29.2A Volts: 120/240 Frequency: 60Hz Outlets: GFCI 120V 20A Duplex (5-20R) (2), 120V 30A Locking (L5-30R), 120/240V 30A (L14-30R) GFCI Outlets: Yes Covered Outlets: Yes Covered Circuit Breakers: Yes Gasoline Run Time at 1/2 Load: 12.5 h. Propane Run Time at 1/2 Load: 5 h. Noise Level: 74 dBA Parallel Capability: No DC Operation: No Voltmeter: Intelligauge Automatic Voltage Regulation: No Battery: Yes Start Type: Recoil, Electric Engine Brand: Champion Engine Size: 459cc Engine Type: 4-stroke Engine Speed: 3600 Fuel Type: Gasoline, Propane (LPG), Natural Gas (NG) Fuel Gauge: Yes Gasoline Capacity: 8.5 gal. Gasoline Tank Material: Steel Engine Oil Type: 10W-30 Engine Oil Capacity: 1.1 qt. Engine Oil Included: Yes Low Oil Shut-Off: Yes Wheels: Yes Wheel Type: Solid Wheel Diameter: 10 in. PGMA G300-2018 Compliant: Yes EPA Certified: Yes CARB Compliant: Yes DIMENSIONS Length: 27.6 in. Width: 28.2 in. Height: 26.0 in. Weight: 207.0 lb.
30kw Ground-Mounted Type EV Charger DC Charging Station Charging Pile JIS Standard, EV Charger, Electric Vehicle Supplier Future Digital Energy Co., Ltd. Price $5200.00 Availability In Stock Model NO. JIS-DCL030A Mounting Ground-Mounted Charging Standard CCS-2/CCS-1/Chademo/ GB/T Single Output Max. Current 125 AMP IP Ratings IP 54 Input Voltage AC380V+-15% Output Voltage DC150-500V(JIS) Cooling Air-Cooled Interface Between Charger and Cms Ethernet/3G/4G/WiFi (Optional) Ocpp 1.6j Transport Package Wooden Case Specification L700*W450*H1680(mm) Trademark Future Digital Energy Origin China HS Code 8504409999 Production Capacity 10000 After-sales Service: 2 Years Warranty Type: Fast EV Charging Station Certification: ISO, RoHS, CE Warranty: 24 Months EV Charger Type: DC Charger Capacity: 30kw 30kw Ground-Mounted Type EV Charger DC Charging Station Charging Pile JIS Standard 30kw Ground-Mounted Type EV Charger DC Charging Station Charging Pile JIS Standard Features Delicate appearance, simple operation, convenient installation; High efficiency, reliable and stable performance; Friendly interaction interface, 7 inches color touch screen; Support Plug&Play, RFID Card/OCPP 1.6J (optional); Support Ethernet/3G/4G/WIFI telecommunication; Support CCS-2/CCS-1/CHAdeMO/ GB/T connector(or Socket) optional; Overload integrated Protection; Support online data upgrade Applicable Scene They are suitable for occasions such as city special charging stations that provide charging for bus, taxi, public service vehicles, sanitation vehicles,logistics vehicles, etc.; city public charging stations that provide charging for private cars, commuter, bus; intercity highway charging stations and other occasions that need special DC fast charging. Standard30kw Ground-Mounted Type EV Charger DC Charging Station Charging Pile JIS Standard Company Profile Future Digital Energy Co., Ltd. is a professional High-tech enterprise that integrates R&D, production, sales and service. We are committed to providing convenient, safe and reliable EV charging overall solutions for every customer. With 30,000 square meters of production plants and more than 50 researchers, our factory has strong R&D advantages and a stable production base in Shenzhen. Accumulative production and shipment quantity exceed 100000 units per year. Our main products include AC EV chargers, DC EV chargers and AC/DC all-in-one charging stations that suitable for home, commercial and public use with CE, ROHS and ISO Certification. We strive to provide customers with the best user experience, high quality assurance and reasonable price. Welcome customers from all over the world to discuss cooperation. Let's build a world that works for tomorrow together.
Hello everyone, We have been engaged in producing and exporting nuts and seeds for 18 years (2006). We export to European countries such as Italy, Austria and Switzerland, as well as to the Arab world. In Germany we work together with large corporations such as Kaufland, Metro, etc. We still have capacity available. Our passion is the distribution of high-quality, fresh nuts of Eastern European origin. Our nuts come from small farms in Eastern Europe. There the nuts are grown in harmony with nature without irrigation systems, pesticides and fertilizers and harvested by hand. It is important to us to promote and further expand these structures. Even without a seal, our walnuts are of organic quality. Our philosophy lies in meeting our customers' requirements and delivering high quality products. We attach particular importance to reliability, honesty and trust in order to build and maintain long-term relationships with our customers. We offer carefully selected premium products whose quality is constantly ensured from incoming goods to outgoing goods in accordance with the standards of ISO 9001 and ISO 22000. This guarantees the highest quality standards. You will receive quality certificates for our products with corresponding technical specifications and analysis reports. The fruits are harvested directly from private tree owners. Neither fertilizers nor pesticides are used. The nuts are only shelled after your order has been received. In addition to freshness, this guarantees an authentic, mild, nutty taste. We have different walnut categories: 1/2 - walnut kernels half 1/4 - quarter 1/8 - fraction 6-8 mm Breakage - 4-6 mm Filling - ready-made mixture for different confectionery (contains nuts, sugar, cinnamon, etc.). This filling can be made according to your wishes and recipe. The minimum order quantity with us is one pallet - 540 kg. However, you can put together the palette from several products. E.g.: 100 kg nuts, 200 kg kernels, 200 kg seeds etc. The nuts are packed in small boxes with air-permeable film (5kg per unit). This means that the nuts remain fresh during transport and storage at the customer's premises until the goods are used. We offer free advice and would be happy to create an individual offer for you. Delivery and VAT 7% are included in the price. The price can be negotiated. We are very flexible and look forward to finding a solution for you. Take a look at our other advertisements and tell us what kind of product you are looking for, we have over 100 products in stock!
CHAMPION 100161 - 7500 WATT ELECTRIC START GENERATOR W/ RV OUTLET & WIRELESS REMOTE Price:$521.08 SKU:100161 Brand:Champion Condition:New Weight:1.00 LBS Shipping:Calculated at checkout Product Description Features Champion 7500 Watt Remote Start Generator Ideal for RV and home backup applications Electric Start (Battery Included) w/ Wireless Remote Start Start and stop from up to 80 ft. away Auto-choke design for easy one-touch starting TT-30 RV & 50A (14-50R) Receptacles Easily connect your 30A RV cord (Not Included) for your power needs 439cc Champion OHV 4-Stroke Engine w/ Low-Oil Shutoff Sensor Provides added protection to extend the life of the generator Cast iron sleeve for long life and easy maintenance 6.1-Gallon Metal Fuel Tank Provides up to 8-hours of run time @ 50% load VoltGuard, Circuit Breaker Protection & GFCI Duplex Outlets Keeps your appliances protected while preventing overload to generator Intelligauge Digital Display Easily monitor your voltage, frequency & operating hours Never Flat Tires & Fold-Down Locking Handle Makes this generator easy to move on even the most bumpy terrain Also Includes Engine Oil 3-Year Limited Warranty - CARB Compliant Specifications Plugs NEMA 5-20R (GFCI) NEMA 5-20R (GFCI) NEMA L14-30R NEMA 14-50R RV Ready 30-Amp Engine Engine Brand Champion Starting System 12-Volt Button Start w/ Recoil CC 439 CC Consumer Engine Warranty 3 Years Engine RPM 3600 RPM Low Oil Alert/Shutdown Yes Cast Iron Sleeve Yes Product Specs Frequency 60 Hertz Surge Watts 9375 Watts Rated Watts 7500 Watts Fuel Type Gasoline Portability Kit Never Flat Wheels Tank Size 6.1 Gallons Run Time @ 50% Load 8 Hours Fuel Tank Material Metal Fuel Gauge No Decibel Rating @ 7m ? 74 dbA Hour Meter Yes Voltage Meter Yes Battery Included Grade Type Emergency Plugs NEMA 5-20R - GFCI 2 NEMA L14-30R 1 NEMA 14-50R 1 RV Ready 30-Amp 1 Overview Made in USA No Weight 207 Pounds Product Style Portable Generator Product Length 27.8 Inches Product Width 27.3 Inches Product Height 26 Inches Consumer Warranty 3 Years UPC 896682000892
Venus Legacy Body Shape slimming device fat removal Radio frequency Skin Tightening Machine. Model: iShape III+ 2024 upgraded best equipo cellulite SPRT v10 sculptor body slim shape machine weight loss for sale 1.Skin Tightening 2. Wrinkle Removal 3. Eyes' area treatments 4. lncrease skin elasticity 5. Fat and cellulite reduction 6. Face wrinkle removal & lifting 7. Warm vacuum cellulite massage 8. Body slimming, contouring & shaping 9. Promote cell metabolism, improveblood circulation 940nm Infrared laser reduces skin impedance by heating skin and RF energy penetrates deeply into connective tissue; The synergistic combination of infrared laser and conducted Bipolar RF energies increase the oxygen intracellular diffusion by heating the skin Vacuum plus specially designed rollers manipulate leads RF penetration to be even 5-15mm. At the same time, Cavitation and Rollers mechanical tissue manipulation nips and stretches fibrillar connective tissue, effectively breaks down subcutaneous fat as well as extruded capillary vessel, Increase lymphatic drainage, promotes metabolism and reduces or shrinks the size of the actual fat chamber and greatly improved body contouring effect; The technology that vacuum folds skin makes RF energy penetrate a specific folded skin, greatly improve effect and safety, even for the upper eyelid area treatment. Technology 1: Cavitation 40KHz Cavitation technology in itself means that the ultrasound causes the fat cells to vibrate so fast (high frequency) so vacuum bubbles are formed in the cell. As a consequence, the outer casing of the fat cells (the membrane) is "blown out" and the fat ends outside the cells. Outside of the membrane, the fat can be broken down to rapidly accessible energy, which is then taken up in the blood or transported by lymph nodes, after which they are either burned or stored in other fat cells elsewhere in the body. Technology 2: Mechanical roller massage The mechanical roller massage works profoundly on densified connective tissues. The mechanical massage rollers enhance the skin's cell-generating activity, resulting in thickened fat deposits being drained. Technology 3: Vacuum massage The vacuum massages lift, mold and massage the skin deep and on the surface. The massage also increases the blood circulation, which in turn leads to the release of fat from the fat cells. The massage further provides a tightening of the skin. Technology 4: Bipolar RF(radio frequency) Bipolar RF makes water molecules in the fat revolve with high speed to produce friction and shock, then triglyceride go out from fat. RF energy with 1-10M could get to 4-15mm skin depth, which makes every layer get heat evenly. The new collagen makes skin turn tighten. This Bipolar RF makes the reorganizing fat cells connect more closely, stimulate the collagen re-grow, avoiding flabby skin after slimming treatment. Technology 5: 980nm infrared light
Product Description 200A/250A/300A/400A/500A/630A DC TIG Welder/MMA Welder/DC Welder/TIG Welding Machine Lift TIG/Hf TIGWelding Machine, Tig Welder, Welding Equipment, Arc/MMA/ZX7 Welding Machine, Inverter Welding, Dc Welder, Welding, Welder, Arc Welder, Power Tool, Welding Solder, Tig Welding, Tig Welder, Mig Welding, Ac Welding Machine, Plasma Cutter, Cutting Machine, Plasma Cutting Machine, welding helmet and power tools. Features: 1.Intelligent interface conversion 2.Adopt IGBT single tube to ensure reliability 3.Unique switching power supply,wide application range of power supply 4.SMT chip design,ensure the duty cycle 5.32-bit microcomputer chip processor,real-time current display 6.Advanced high-efficiency inverter technology,35khz,high working frequency 7.Usable for generator, suitable for field operation 8.Automatically save the parameters of the last operation 9.Overheat,over voltage,under voltage protection to prevent machine damage 10.Colored LCD display,easy to use WHY CHOOSE US? Q1.Are you manufacturer or trading company? A.We are the only manufacturer of electrical products.Welcome to visit our factory at any time. Q 2. what's the payment term? A. We accept T/T etc. Q 3. What's the delivery time ? A. Normal model 1-3days,because we have ability to do the stock.For big order,it takes about 15-20days. Q 4. What is the standard of package? A. Export standard package or special package according to customer requirement. Q 5. what kind of product quality your factory offer? A. We are professional factory and we offer top quality to help client to get more market. Q 6. Do you accept OEM business? A. We do OEM . Q 7.Which market do you already sell? A.We already ship to Europe,America, Oceania etc. Q8. what kind of certificate you have ? A.We have CE, GS, ROHS, EMC etc. Model CUT-30 CUT-45PFC CUT-60CNC CUT-65CNC CUT-80CNC CUT-100CNC CUT-120CNC Rated Input Voltage(V) 1~230 95~275 3~400 3~400 3~400 3~400 3~400 Input Frequency(Hz) 50/60 50/60 50/60 50/60 50/60 50/60 50/60 Rated Input Current(A) 40 29 15.7 18 30 33 43 No-load Voltage(V) 320 265 400 400 415 415 415 Power Factor 0.65 0.99 0.7 0.7 0.7 0.7 0.7 Output Current Range (A) 10-30 10-45 15-60 15-65 15-80 15-100 15-120 Duty Cycle(%)40C�° 25% 25% 60% 60% 60% 60% 80% Efficiency(%) 80 80 80 80 80 80 80 Insulation Class H H H H H H H Protection Class Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Weight(Kg) 7 8.5 18 20 25 30 32 Dimension(mm) 360x180x330 410X180X330 410X220X405 410X220X405 450X220X405 450X220X405 550X260X490
Product Description 200A/250A/300A/400A/500A/630A DC TIG Welder/MMA Welder/DC Welder/TIG Welding Machine Lift TIG/Hf TIGWelding Machine, Tig Welder, Welding Equipment, Arc/MMA/ZX7 Welding Machine, Inverter Welding, Dc Welder, Welding, Welder, Arc Welder, Power Tool, Welding Solder, Tig Welding, Tig Welder, Mig Welding, Ac Welding Machine, Plasma Cutter, Cutting Machine, Plasma Cutting Machine, welding helmet and power tools. Features: 1.Intelligent interface conversion 2.Adopt IGBT single tube to ensure reliability 3.Unique switching power supply,wide application range of power supply 4.SMT chip design,ensure the duty cycle 5.32-bit microcomputer chip processor,real-time current display 6.Advanced high-efficiency inverter technology,35khz,high working frequency 7.Usable for generator, suitable for field operation 8.Automatically save the parameters of the last operation 9.Overheat,over voltage,under voltage protection to prevent machine damage 10.Colored LCD display,easy to use WHY CHOOSE US? Q1.Are you manufacturer or trading company? A.We are the only manufacturer of electrical products.Welcome to visit our factory at any time. Q 2. what's the payment term? A. We accept T/T etc. Q 3. What's the delivery time ? A. Normal model 1-3days,because we have ability to do the stock.For big order,it takes about 15-20days. Q 4. What is the standard of package? A. Export standard package or special package according to customer requirement. Q 5. what kind of product quality your factory offer? A. We are professional factory and we offer top quality to help client to get more market. Q 6. Do you accept OEM business? A. We do OEM . Q 7.Which market do you already sell? A.We already ship to Europe,America, Oceania etc. Q8. what kind of certificate you have ? A.We have CE, GS, ROHS, EMC etc. Model CUT-30 CUT-45PFC CUT-60CNC CUT-65CNC CUT-80CNC CUT-100CNC CUT-120CNC Rated Input Voltage(V) 1~230 95~275 3~400 3~400 3~400 3~400 3~400 Input Frequency(Hz) 50/60 50/60 50/60 50/60 50/60 50/60 50/60 Rated Input Current(A) 40 29 15.7 18 30 33 43 No-load Voltage(V) 320 265 400 400 415 415 415 Power Factor 0.65 0.99 0.7 0.7 0.7 0.7 0.7 Output Current Range (A) 10-30 10-45 15-60 15-65 15-80 15-100 15-120 Duty Cycle(%)40C�° 25% 25% 60% 60% 60% 60% 80% Efficiency(%) 80 80 80 80 80 80 80 Insulation Class H H H H H H H Protection Class Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Weight(Kg) 7 8.5 18 20 25 30 32 Dimension(mm) 360x180x330 410X180X330 410X220X405 410X220X405 450X220X405 450X220X405 550X260X490
Hydraulic end assembly AH0501010500 AH35001-05.00 Sealing washer AH0501010203 AH35001-02.03 Crankshaft assemble AH1301010200 AH36001-02.00 Oil seal ring AH1301010405 AH36001-04.21 Adapter connectorZG2-1/2â?³ AH1001010807 AH33001-08A.07 Hydraulic end assembly AH0801010500 AH34001-05.00 Sealing washer AH0801010203 AH34001-02.03 Crankshaft assemble AH1601010100 AH37001-01.00 O-ring �?190�?3.55 530301011900035507 GB3452.1-82 Short circuitZG2-1/2â?³-NPT2-1/2 AH1001010808 AH36001-08C.04 Hydraulic end assembly AH1001010500 AH33001-05.00 Sealing washer AH1001010203 AH33001-02.03 Pinion Shaft assemble AH1301010300 AH36001-03.00 Two-lip seal 5"X6.25"X0.625" AH1301010406 AH36001-04.08A Flexible pipe �¦22�?�¦37 AH1001010180001 L=1500 Exhaust filter assembly AH0501011400 AH35004-11.00 Inner ring AH0501010204 AH35001-02.04 Pinion Shaft assemble AH1601010200 AH37001-02.00 Locking spring AH1301010407 AH36001-04.13 Gladhand �¦22�?�¦37 AH100101080900 AH33001-08.18.00 Exhaust filter assembly AH1001011900 AH33014-04.00 Inner ring AH0801010204 AH34001-02.04A Crossing Head Assemble AH1301010400 AH36001-04.00 Splash guard AH1301010408 AH36001-04.10 90�°Elbow NPT1â?³ AH1001010810 AH33001-08.16 Cross head assembly AH0501010400 AH35001-04.00 Inner ring AH1001010204 AH33001-02.04 Hydraulic End Assemble AH1301010500 AH36001-05A.00 Extension rod AH1301010409 AH36001-04.11 Adapter connector NPT2-1/2³ AH0801020801 AH34001-08B.07 Cross head assembly AH0801010400 AH34001-04.00 Outer ring AH050101020500 AH35001-02.05.00 Power end lubrication assembly AH1301010600 AH36001-06C.00 Crosshead pin AH1301010410 AH36001-04.12A Sealing washer AH1001010814 AH36001-08B.09 Cross head assembly AH1001010400 AH1001010400 Outer ring AH080101020500 AH34001-05.00 Base Seat AH1301010700 AH36001-07K.00 O-ring �?160�?7 530301011250070000 GB3452.1.-82 NPT1â?³Flange AH1001010815 AH36001-08B.10 Pinion shaft assembly AH0501010300 AH35001-03.00 Outer ring AH100101020500 AH33001-02.05.00 Spray Pump Assembly AH1301010800 AH36001-08C.00 Bolt M20�?65 T502-6005K T52-6005K Bead apex A-3708 140301012031500000 GB1171-74 Pinion shaft assembly AH0801010300 AH34001-03.00 connecting rod AH0501010206 AH35001-02.06 Sealing washer AH10010109 AH33001-09 Sealing gasket AH1301010411 AH36001-04.15 Flexible pipe �¦38�?�¦53 AH100101080002 �¦38�?�¦53-L=750 Pinion shaft assembly AH1001010300 AH33001-03.00 connecting rod AH0801010206 AH34001-02.06 Breather Cap T515-1001.00 T515-1001.00 O-ring 160�?7 530301011600070000 GB3452.1-82 90 Elbow
CE Approve 2024 Intense Pulsed Light Hair Removal Ipl Laser Depilador Ipl Vascular Electrolysis Hair Removal Machine Home Use Ipl Machine. QM-120 Different combination from IPL Diode Laser, Nd:YAG Laser, RF,etc. Applications 1. Permanent hair removal for all skin types and all hair colors! 2. Skin rejunvenation 3. Pigments removal 4. Wrinkle removal 5. Acnes removal 6. Vascular Removal Working Principle IPL Intense Pulse Light("IPL") used broad spectrum of white light and with filters to marrow the spectrum to target specfic chromophores and structures. IPL is a non-invasive skin treatment that emits powerful bursts of light energy to treat unwanted hair, sun damaged skin, and wrinkles, etc. without damaging the surface of your skin, IPL systems use flash xenon lamps to emit micro pulses of light across a broad band of visible wavelengths. IPL work by using particular wavelengths of light that is called by melanin which colors the hair and brown skin and black. Since melanin absorbs light to be warm or hot, that the production of cells called melanocytes and melanin are denatured more produce more melanin. By using gentle pulses of light momentarily to create heat, IPL can permanently disable hair follicles, preventing hair follicles` future growth. The melanin in the hair (which gives it its colour) absorbs the light, which is then converted into heat. This heat is transferred to the growth cells surrounding the root of the hair, disabling them. By the IPL, pigments are Shattered and eliminated out of body via metabolism. At the same time,IPL also helps increase collagen production, which rejuvenates the skin leading to a more youthful, radiant, bright and few fine wrinkle skin. The light with long wavelength can pass through epidermis to the hair follicles deep underneath the skin. At the targeted area, IPL occurs heating to destroy follicles and hair structures leading to permanent hair removal. SSR It is a revolutionary approach, rather that bombarding your skin with high amounts of damaging energy. SSR fires multiple shots but at low Joules, in doing so it gently heats the hair follicle to the heat needed and the most you will feel is warmth and a tingling sensation, some clients comparing it to a warm massage. SSR also utilizes In-Motion technology, where the hand piece is always in motion over the skin. Specialty of QM-120 Unique and Ergonomic design Handpiece.(2 designs for option) 5 filters for different treatment Top-level Spare parts adopted, guarantee its golden quality and long-lasting lifetime!
Professional HIFU-Q3 New arrival skin tightening focused ultrasound anti-wrinkle face hifu 7d facial and body. Model:HIFU-Q3 Working Theory: High Intensity Focused Ultrasound (HIFU) directly delivers heat energy to skin and subcutaneous tissue that can stimulate and renew the skin's collagen and thus consequently improving the texture and reducing sagging of the skin. It literally achieves the results of a facelift or a body lifts without any invasive surgery or injections, moreover, an added bonus of this procedure is that there is no downtime. This technique can be applied to the face as well as the whole body, and also, it works equally well for people of all skin colours, in contrast to that of lasers and the intense pulse lights. HIFU machine is a non surgical and a non laser procedure that directs high intensity focused ultrasound, also known as HIFU knife into the deep skin layer in order to gently heat the tissue to lift and tighten aged skin without any incisions of disrupting skin surface. HIFU technology is able to transfer the heat energy into 3-4.5mm under the surface of the skin. It will heat the SMAS up to 60-70 temperature the raises thermal coagulation point which accelerates skin rejuvenation process and maximizes tightening effect of the skin layer. How it works? Advanced High Intensity Focused Ultrasound(HIFU) adopts technology which is not like lasers, radio frequency, surgery and other technologies, HIFU is non-surgical. HIFU steer around the surface of the skin to deliver the precise and fractional of ultrasound energy at the right depths(i.e.3.0mm/ 4.5mm SMAS layer) without damaging or disrupting the epidermal tissue of skin and the right temperature 65~70ºC.This energy stimulates the new collagen to reproduction, which rejuvenates the skin leading to a more youthful and bright or to sharpen contouring. HIFU is especially suitable for treating sagging skin with reasonable thickness as well. Machine Advantages: 1. Non-Invasive treatment both for face and body with different cartridge; 2. Adopts HIFU technology, the temperature of focused ultrasound can reach 65 ºC to 100 ºC; 3. Security control system can distinguish different cartridge automatically; 4. Special Cartridge connect method make sure no energy loss during the treatment; 5. Professional mode with free setting parameter and memory function for saving data; 6. Smart mode with limited energy and preset parameters for simple and safe treatment; 7. Uniform energy distribution brings better clinical effect and quickly treatment; 8. Cartridge with long life span of 10,000 shots; 9. HIFU-Q3 has 2 extra transducer 8mm and 13mm,which give you an option for body treatment: body tightening ,lifting and slimming.
TECHNICAL NAME: IRON ORE FROM 63% TO 64%. ORIGIN: PERU QUANTITY: 50.000- 150,000 MT PER MONTH. PACKAGING :BULK CONTRACT :SUPPLY YEAR 2.000.000 MT. PAYMENT METHOD: SBLC / DLC TRANSFERABLE, DIVISIBLE and IRREVOCABLE. MT 760 DIVISIBLE AND TRANSFERABLE /MT 103 - TT- WIRE (TOP 25 BENCH). TYPE OF CONTRACT AND VALUE OF PRODUCT: FOB Port of Peru USD 72 MT DURATION OF THE CONTRACT: 12-MONTH CONTRACT, RENEWABLE BY AGREEMENT OF THE PARTIES. CERTIFICATIONS :SGS OF QUALITY AND QUANTITY AT PORT OF ORIGIN. VENDOR COMPANY: MAKES CONTRACT AND OFFERS 2% PERMANCE BOND GUARANTEE TO THE BUYER. Additional Information: Consider That, Once The Contract Has Been Signed, The First Shipment Will Be Made 15 Days After The Payment Document Has Been Accepted, And Successive Deliveries Every 30 Days. COMMERCIAL PROCEDURE 1.- The buyer issues an official order (LOI / CPO accompanied by CP company profile), proof of funds (RWA), passport copy and company registration to the seller to which the seller responds with an FCO. 2.- The Buyer as a token of acceptance sends by e-mail the signed and stamped confirmation of the offer submitted by the Seller, with the respective date of acceptance. 3.- Buyer and Seller discuss the conditions set forth in the Draft Supply Contract, as a sign of acceptance, sign the terms and conditions, procedure to formalize the contract, which will be sent via e-mail. 4. The Buyer's Bank shall, within five business days, send the draft financial instrument (SBLC) to the Seller's nominated Bank. 5. The Seller will then send the POP documents to the buyer: A.- Certificate of Origin. B.- Supply commitment. C.- Product passport. d.- Declaration of product availability. Once the draft of the financial instrument is approved, the Buyer's Bank issues the instrument (SBLC) to the Bank designated by the Seller. 7.- Once the Financial Instrument is confirmed, the Seller will send the complete POP and the following documents v�?Ã?Âa Swift from bank to bank: A.- Export Permits of the Product, B.- Certificate of title of the allotment title. C.- Port Storage Contract. D.- Transportation contract to the port of unloading. E.- Quality and quantity certificate from SGS. F.- Bill of Lading (BL). 8.- contract deliveries start as agreed. 9.- The buyer performs an SGS inspection at the port and/or airport of delivery. Note: Immediate availability to load 200,000 MT IRON.
Miniature Circuit Breaker Automatic Assembly and inspecting line MCB Automatic Assembly and inspecting line Keyword: Miniature Circuit Breaker Automatic Assembly, Miniature Circuit Breaker, Automatic Assembly line, Assembly Machine, Assembly Production Line Product Introduction Basic operation process: ï?¼Loading by AGV robots, printing QR codes based on the product work order issued by the SAP system, and then separating the upper and lower shells. ï?¼Bottom coating of the upper shell: The installation of three components is completed through ten processes, and after each assembly is completed, there is a corresponding installation accuracy testing process to ensure that the assembly is completely qualified. ï?¼Installation of lower shell components, upper and lower shell assembly: A total of 25 processes are used to install 12 components. After each part is assembled, guide pins are used to ensure the upper and lower assembly. After the installation of internal components is completed, the product's on/off function is tested. After passing the test, rivets are installed, pressed again, and the screws are removed. All installations are checked, and after passing the test, they are transferred to the inspection station. ï?¼Unipolar products undergo instantaneous detection, delay detection, cooling tower and other unit inspections, and are then labeled with QR codes and covers before being transferred to the next workstation. ï?¼Multi pole products require 9 steps of multi pole assembly, and after assembly, a second delay is performed to verify the stability and reliability of the product ï?¼Finally, it is transferred to the automatic packaging unit through pressure resistance testing, transfer printing, laser labeling, and buckle installation. The specific parameters: (1) Equipment input voltage: 220V �± 10%, 50Hz; (2) The equipment has functions such as automatic shell loading, lid opening, assembly of arc extinguishing plates, magnetic guide plates, handle springs, base springs, positioning pins, handles, jump buckles, locks, coil components, iron core components, wiring columns, adjustment screws, arc extinguishing covers, CCD recognition, lid closing, identification of qualified and unqualified products, assembly of cutting processes, online detection, real-time monitoring, component life monitoring, data storage, MES system and ERP system networking, parameter arbitrary formula, smart energy analysis and energy-saving management system, intelligent equipment service big data cloud platform, etc. (3) Theoretical production effeciency: 2 seconds per unit; Daily production of approximately 14400 pieces/8 hours; (4) This device has the function of power-off to save data for 30 days, making it easy to manage production data; (5) This device adopts touch screen operation, has a computer communication interface, and printing function
Miniature Circuit Breaker Automatic Assembly and inspecting line MCB Automatic Assembly and inspecting line Keyword: Miniature Circuit Breaker Automatic Assembly, Miniature Circuit Breaker, Automatic Assembly line, Assembly Machine, Assembly Production Line Product Introduction Basic operation process: ï?¼Loading by AGV robots, printing QR codes based on the product work order issued by the SAP system, and then separating the upper and lower shells. ï?¼Bottom coating of the upper shell: The installation of three components is completed through ten processes, and after each assembly is completed, there is a corresponding installation accuracy testing process to ensure that the assembly is completely qualified. ï?¼Installation of lower shell components, upper and lower shell assembly: A total of 25 processes are used to install 12 components. After each part is assembled, guide pins are used to ensure the upper and lower assembly. After the installation of internal components is completed, the product's on/off function is tested. After passing the test, rivets are installed, pressed again, and the screws are removed. All installations are checked, and after passing the test, they are transferred to the inspection station. ï?¼Unipolar products undergo instantaneous detection, delay detection, cooling tower and other unit inspections, and are then labeled with QR codes and covers before being transferred to the next workstation. ï?¼Multi pole products require 9 steps of multi pole assembly, and after assembly, a second delay is performed to verify the stability and reliability of the product ï?¼Finally, it is transferred to the automatic packaging unit through pressure resistance testing, transfer printing, laser labeling, and buckle installation. The specific parameters: (1) Equipment input voltage: 220V �± 10%, 50Hz; (2) The equipment has functions such as automatic shell loading, lid opening, assembly of arc extinguishing plates, magnetic guide plates, handle springs, base springs, positioning pins, handles, jump buckles, locks, coil components, iron core components, wiring columns, adjustment screws, arc extinguishing covers, CCD recognition, lid closing, identification of qualified and unqualified products, assembly of cutting processes, online detection, real-time monitoring, component life monitoring, data storage, MES system and ERP system networking, parameter arbitrary formula, smart energy analysis and energy-saving management system, intelligent equipment service big data cloud platform, etc. (3) Theoretical production effeciency: 2 seconds per unit; Daily production of approximately 14400 pieces/8 hours; (4) This device has the function of power-off to save data for 30 days, making it easy to manage production data; (5) This device adopts touch screen operation, has a computer communication interface, and printing function
Xiongcai Water Pump Motor Controller Approved by The Biggest Water Pump Manufacturer In China. 1. Voltage DC16~36V 2. Rated Current 4.6A 3. Working Temp -40 125 4. Working Humidity 95% 5. Size: 61*56*17mm 6. Protection under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Xiongcai Technology has been specializing in motor controller since 2011, we engineer, analyze, test and supply finished products. At present, in China, most of manufacturers provide OEM service only, they don�¢??t support you in technology, but just provide OEM. We serve you from initial concept to product supply. Unicent Automotive Tech, a company focused in automotive thermal management, contacted us and inquired ab out motor controller for automotive water pump. They have high requirements on reliability, performance and safety. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed budget. Xiongcai team wanted to give a shot. R&D team designed a potent combination of software and hardware meticulously, called XCA107 with power system of 4.6A, DC16-36V, making parameters up to the customer's requirements. After one year test and verification, XCA107 motor controller for water pump was approved. The client has introduced this product for 4 years till now. XCA107 Motor Controller For water pump provides protection measures including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit. That means this product would stop when the protection measure is triggered, but never be damaged. Furthermore, this product is certified by CSIPER25, ISO11452-2, ISO10605, ISO16750, ISO7637. You don�¢??t need to worry about the reliability. We are one of the few engineering companies providing a full service from design to supply, and serving top clients in auto industries, such as NISSAN, XPeng, Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto(FLACC), Keshen, Unicent and more.
Xiongcai Motor Controller Applied In Cummins Engine 1. Voltage DC16~36V 2. Rated Current 10A 3. Working Tempï¼?-40ï½?85â?? 4. Working Humidityï¼?95% 5. Size: 87*84*15mm 6. Protectionï¼?under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Since 2011, Xiongcai Technology has been a pioneering company in specialized field of motor controller for automotive Fuel Pump. Founded by experienced engineer, Xiongcai tends to be at the leading edge of technological development of motor controller for automotive fuel pump. In 2018, Joinhands Auto Parts, a company specialized in design and manufacture of automotive fuel pump, contacted us and inquired about motor controller for their products. The client was really picky and particular, their engineer team set a standard on protection measure beyond the industry because this product is designed for Wuhan Cummins, one of greatest engine manufacturers in China. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed budget. Xiongcai team evaluated the requirements and decided to have a try. Engineered from ground up, Xiongcai R&D team designed a combination of software and hardware meticulously called XCA105, making all parameters up to customer�¢??s standard. After one year test and verification, Xiongcai XCA105 motor controller for fuel pump was approved. The client has introduced this product for 6 years till now. Xiongcai XCA105 motor controller for fuel pump with 8A current, DC8-18v power system, working humidity 95% max, providing protection including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit protection. And this product certified by CSIPER25, ISO11452-2, ISO10605, ISO16750, ISO7637. XCA105 motor controller is a trusted product and Xiongcai is a trusted partner. We are one of the few engineering companies providing a full service from design to supply of product, which means we design, analyze, test and supply finished products. Xiongcai is partnering with top clients in auto industries, Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto(FLACC), Keshen, Unicent and more.
Xiongcai Motor Controller Has Been Introduced By The Largest Auto Fuel Pump Manufacturer 1. Voltage DC16~36V 2. Rated Current 10A 3. Working Temp -40 85 4. Working Humidity 95% 5. Size: 87*84*15mm 6. Protection under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Xiongcai Technology tends to be at the leading edge of technological development of motor controller for automotive Fuel Pump. XIONGCAI TECH is one of the few manufacturers that focus on motor controller (electronic speed control or ESC) only, especially for automotive fuel pump. In 2017, ACHR Electrical Machinery, a company specialized in design and manufacture of automotive fuel pump. They contacted us and inquired about motor controller for their products. The client was really picky and particular, their engineer team set a standard on protection measure beyond the industry because this product is designed for the greatest automobile engine group in China�¢??FAWDE. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed cost budget. Xiongcai team wanted to give a shot. Xiongcai R&D team designed a combination of software and hardware meticulously called XCA105, making all parameters up to customer�¢??s standard. After one year test and verification, Xiongcai XCA105 motor controller for fuel pump was approved. The client has introduced this product for 6 years till now. Xiongcai RD team designed perfect protection measures to protect the motor. a. Peak current limit. This measure will limit the peak current to avoid damage to motor; b. Single PWM periodical current detection limit reduces impact of pulse current to motor; c. Waterproof is designed for all weather condition, up to IP67. The ESC is potted in epoxy to protect the electronics and improve heat transfer, enabling motor controller working in any condition at a lower temperature; And more protection measures including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit protection. Furthermore, XCA105 motor controller was certified by CSIPER25, ISO11452-2, ISO10605, ISO16750, ISO7637. We are one of the few engineering companies providing a full service from design to supply of product, including design, analyze, test and supply finished products. Xiongcai is serving top clients in auto industries, ACHR, Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto(FLACC), Keshen, Unicent and more. Contact us Shenzhen Xiongcai Technology Co., Ltd for detail. We try to assist you in achieving your idea.
Perimeter Detection Systems Raycom utilizes Perimeter Intrusion Detection Systems (PIDS) to ensure organizations are completely secure and help reduce operational risk. As threat levels continue to increase, it is becoming critical for organizations to properly protect their assets. This starts at the perimeter of their sites, and there has never been a more important time to deploy a robust, reliable and secure detection strategy to reduce operational risk. Timely and highly accurate location information about potential intruders ensures a quick and appropriate response to minimize damage. Ensure that your perimeter intrusion detection system is fully integrated into your security solution, providing real-time data. Thus creating the ability to track and respond to intruders. Fiber optic technology is fast becoming the technology of choice. Especially for organizations looking to deploy a cost-effective, reliable solution and significantly reduce the entire lifecycle cost of ownership. Raycom's family of advanced fiber-optic intrusion detection solutions provides covert buried and fenced or wall-mounted detection through a single detection unit. With fully scalable systems for sites ranging from less than 5 kilometers to more than 100 kilometers, Raycom has a solution for you. Resistant to cable cuts and vandalism All Raycom PIDS detection units are available in 1-channel or 2-channel models. 2-channel models will continue to provide uninterrupted detection along the perimeter. This is true even if the cable is cut or damaged. Lower cost of ownership Overall lower installation and maintenance costs compared to alternative technologies. In addition, no power supply is required on site. Minimize nuisance alarms Utilizing artificial intelligence technology, our market-leading detection algorithms are able to develop acoustic fingerprints of different events. This allows differentiation between genuine security risks and irrelevant ambient noise Multiple fence types Due to its unique configuration capabilities, the Raycom solution is suitable for every fence type without compromising location accuracy or event categorization capabilities. Positioning accuracy Advanced signal processing technology combined with intelligent algorithms can quickly and accurately identify the exact location of a potential threat within �±5m. Integration Our advanced software seamlessly integrates with a wide range of commonly used third-party systems. This provides operations teams with real-time information from a range of devices through a single interface. Covert Buried Detection Our buried solutions are fully covert and can detect people and vehicles long before they enter the site, ideal where there is a lack of physical boundaries.
Like other members of the Cordyceps genus, C. militaris produces the pharmacologically active compound cordycepin. Cordycepin is a nucleoside analogue of adenosine-differing by only a single hydroxyl group. It has been shown to induce apoptosis, reduce inflammation, and inhibit RNA transcription in cell cultures. Cordyceps, a genus of more than 400 species within the order Hypocreales, are commonly known as vegetable caterpillars, or caterpillar fungi. C. militaris parasitizes insects. It forms a small, 3- or 4-centimetre (about 1.3-inch) mushroomlike fruiting structure with a bright orange head, or cap. 6 Benefits of Cordyceps, All Backed by Science Cordyceps is a genus of parasitic fungi that grows on the larvae of insects. When these fungi attack their host, they replace its tissue and sprout long, slender stems that grow outside the hostâ??s body. The remains of the insect and fungi have been hand-collected, dried and used in Traditional Chinese Medicine for centuries to treat fatigue, sickness, kidney disease and low sex drive. Supplements and products containing Cordyceps extract have become increasingly popular due to their many purported health benefits. Of the more than 400 species of Cordyceps discovered, two have become the focus of health research: Cordyceps sinensis and Cordyceps militaris. However, much of this research is limited to animal or lab studies, so health experts currently canâ??t draw conclusions about their effects on people. However, their potential health benefits are promising. This article highlights 6 potential benefits of Cordyceps, based on science. 1. May Boost Exercise Performance 2. Anti-Aging Properties 3. Potential Anti-Tumor Effects 4. May Help Manage Type 2 Diabetes 5. Possible Benefits for Heart Health 6. May Help Fight Inflammation Dosages Due to limited research in humans, there is no consensus on dosages. The dosage commonly used in human research is 1,000â??3,000 mg per day. This range is not associated with side effects and has been found to have certain health benefits. Side Effects and Safety No studies have yet examined the safety of Cordyceps in humans. However, a long history of use in Traditional Chinese Medicine suggests they are nontoxic. In fact, the Chinese government approved Cordyceps CS-4 for use in hospitals and recognizes it as a safe, natural drug (32).
Product Details Main Difference Between Art Paper &art Board Coated paper and copperplate card are often used in printing, so what is the difference between copperplate paper and copperplate card.In general,coated paper is lighter and thinner than copper cardboard. The quality of copper paper is better. Uses are also different. The characteristic of coated paper is that the paper surface is very smooth and smooth, high smoothness and good gloss. Because the whiteness of the coating used is more than 90%, and the particles are very fine, and after the super calender, so the smoothness of coated paper is generally 600-1000s. At the same time, the paint is very evenly distributed on the paper and shows a pleasing white. The requirement for coated paper is that the coating is thin and uniform, without bubbles, and the adhesive dose in the coating is appropriate to prevent the paper from depowdering and hair shedding in the printing process. In addition, the absorption of xylene on coated paper should be appropriate The following is the detailed difference between coated paper and copperplate card: First, the characteristics of coated paper 1, molding mode: a molding 2, material: high quality raw materials 3, thickness: general 4. Paper surface. exquisite 5, dimensional stability: good 6,intensity:. A. Toughness: Average B.Internal combination: Good 7,the main use: album, packaging noodles Two, the characteristics of copper plate card 1, molding mode: a molding multiple molding together, generally three layers 2.Material: cheap fiber can be used in the middle 3,thickness: thick 4. Paper surface: slightly rough 5,dimensional stability: slightly poor 6, intensity. A. Toughness: High B. Internal bonding: easy to be layered 7,main use: packaging box, manual cover Product Description: Name: High Bulk art board Color: White Material: 100% Wood Pulp Substance,230gsm,250gsm,270gsm,300gsm,325gsm,350gsm,365gsm,400gsm,etc Size: 600*900mm, 700*1000mm,787*1092mm, 880*1194mm or width >600mm in roll size, etc. Features: 100% virgin pulp, High printing gloss, Smooth printing surface High gloss, Excellent brightness and smoothness Competitive stiffness and caliper , True color reproduction ISO 9001:2000,ISO14001:2004,SGS,FSC ARE ALL AVAILABLE Application Good quality business card,wedding card,invitation card,etc. Books Cover High class box like medicine box,cosmetics box,perfume box,shoe box,etc. Food packaging like tray,hamburger box,chicken box or other food packaging box. Product Packing Roll packing Wrapped with 3 layers strong PE coated craft liner paper. in case of paper damaged during the transit. Bulk sheets packing BOPP film wrapped, baled on strong wooden pallet, 4 angles be protected by carton board Ream packing 100 sheets wrapped by strong PE coated craft paper, baled on wooden pallets with 4 angle protectors