Model L126TIM Engine type 4 cycle, In line, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 400(294)/2,100 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.85 Compression ratio 17 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 77 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 6.0 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 24 / 19 Fresh water pump type Centrifugal type, driven by gear Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT144H (Dong-I ) Gear ratio 1.83 2.09 2.51 3.08 3.43 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,414 x 933 x 1,077 with M. gear mm 1,683 x 933 x 1,159 Engine dry weight without M/G kg 1,060 with M. gear kg 1,345
Model L126TIH Engine type 4 cycle, In line, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 360(265)/2,000 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.33 Compression ratio 17 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 67 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 6.0 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 24 / 19 Fresh water pump type Centrifugal type, driven by gear Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT144H (Dong-I ) Gear ratio 1.83 2.09 2.51 3.08 3.43 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,414 x 933 x 1,077 with M. gear mm 1,683 x 933 x 1,159 Engine dry weight without M/G kg 1,060 with M. gear kg 1,345
Model MD196TI Engine type 4 cycle, In line, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 320(235)/2,000 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.33 Compression ratio 16.5 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 61 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 6.0 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 24 / 19 Fresh water pump type Centrifugal type, driven by gear Sea water pump type Rubber impeller type driven by gear Marine gear Model TK450 (TaePyongYang) Gear ratio 1.97 2.53 3.04 3.42 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,397 x 933 x 1,077 with M. gear mm 1,695 x 933 x 1,155 Engine dry weight without M/G kg 1,009 with M. gear kg 1,329
Model L086TIM Engine type 4 cycle, In line, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 315(232)/2300 Displacement( cc ) 8,071 Cylinder number - bore x stroke( mm ) 6 - 111x 139 Mean piston speed (m/sec. ) 10.66 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 62 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 4.5 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 27 / 25 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT110A (Dong-I) Gear ratio 1.77 2.09 2.42 2.82 3.19 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,364 x 919 x 965 with M. gear mm 1,552 x 919 x 1,062 Engine dry weight without M/G kg 790 with M. gear kg 1,015
Model L136TI Engine type 4 cycle In line direct injection water cooled with turbo charger inter cooler Rating output BHP PSkWrpm 2301692200 Displacement cc 8071 Cylinder number bore x stroke mm 6 111x 139 Mean piston speed msec 1019 Compression ratio 167 1 Firing order 1 5 3 6 2 4 Governor type of injection pump Mechanical all speed RSV Fuel consumption lit h 45 Starting system Electric Starting by starter motor Starter motor capacity V kW 24 45 Alternator capacity V A 24 50 Battery V Ah 24 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max Min lit 27 25 Fresh water pump type Centrifugal type driven by V belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT110A DongI Gear ratio 177 209 242 282 319 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size L x W x H without MG mm 1364 x 911 x 937 with M gear mm 1552 x 911 x 1027 Engine dry weight without MG kg 773 with M gear kg 994
Model L136T Engine type 4 cycle, In line, direct- injection, water cooled, with turbo charger Rating output (B.H.P) PS(kW)/rpm 200(147)/2200 Displacement( cc ) 8,071 Cylinder number - bore x stroke( mm ) 6 - 111x 139 Mean piston speed (m/sec. ) 10.19 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 37 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 4.5 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 27 / 25 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT90A (Dong-I) Gear ratio 1.61 2.06 2.45 2.82 3.12 3.46 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,351 x 893 x 937 with M. gear mm 1,351 x 893 x 937 Engine dry weight without M/G kg 748 with M. gear kg 938
Model L136 Engine type 4 cycle, In line, direct- injection, water cooled, aspirated naturally Rating output (B.H.P) PS(kW)/rpm 160(118)/2200 Displacement( cc ) 8,071 Cylinder number - bore x stroke( mm ) 6 - 111 x 139 Mean piston speed (m/sec. ) 10.19 Compression ratio 17.6 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 32 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 4.5 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 25 / 23 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT90AF (Dong-I) Gear ratio 1.61 2.06 2.45 2.82 3.12 3.46 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,266 x 875 x 937 with M. gear mm 1,542 x 875 x 963 Engine dry weight without M/G kg 743 with M. gear kg 928
Parameter: Maximum swing diameter over bed: 800 mm; Maximum turning length: 3000 mm; Maximum length of two centers: 3000 mm; Spindle bore diameter: 104 mm; Spindle nose type D11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 5.4-720(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.06-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 480 mm; Transverse travel of lower tool rest: 500 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 5900 kg; Machine overall size: 5160x1450x1630 mm;
Parameter: Unit Maximum swing diameter over bed: 800 mm; Maximum turning length: 1500 mm; Maximum length of two centers: 1500 mm; Spindle bore diameter: 104 mm; Spindle nose type D11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 5.4-720(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.06-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 480 mm; Transverse travel of lower tool rest: 500 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4900 kg; Machine overall size: 3660x1450x1630 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 1000 mm; Maximum length of two centers: 1000 mm; Spindle bore diameter: 104 mm; Spindle nose type D11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 5.4-720(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.06-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 480 mm; Transverse travel of lower tool rest: 500 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4200 kg; Machine overall size: 3160x1450x1630 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 3000 mm; Maximum length of two centers: 3000 mm; Spindle bore diameter: 104 mm; Spindle nose type A11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 7.5-1000(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.05-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 350 mm; Transverse travel of lower tool rest: 400 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 5700 kg; Machine overall size: 5160x1380x1450 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 1500 mm; Maximum length of two centers: 1500 mm; Spindle bore diameter: 104 mm; Spindle nose type A11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 7.5-1000(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.05-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 350 mm; Transverse travel of lower tool rest: 400 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4700 kg; Machine overall size: 3660x1380x1450 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 1000 mm; Maximum length of two centers: 1000 mm; Spindle bore diameter: 104 mm; Spindle nose type A11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 7.5-1000(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.05-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 350 mm; Transverse travel of lower tool rest: 400 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4000 kg; Machine overall size: 3160x1380x1450 mm;
S&S Cycle V111 V Series Black Edition Complete Engine with 585 Camshaft The Black Edition S&S motors combine classic wrinkle black with high gloss covers for a subtle contrast and elegant look while still producing the power and reliability you've come to expect from S&S, which is legendary performance Durable powder coat finish, wrinkle black cases, cylinders and heads, and gloss black covers are all a part of this engine S&S V111 engines are perfect for applications that require great horsepower and torque, but not at the expense of dependability and engine life They are similar to the V124 engines, but the shorter stroke results in lower piston speed for longer engine life and less vibration The lower compression ratio makes fuel requirements less critical, and the automatic electric compression releases make starting even easier Large cooling fins increase cooling efficiency Shorter than stock height makes installation easy Gloss black rocker covers, air cleaner cover, oil pump, gear cover, tappet blocks and pushrod tubes are all included 9.8:1 Compression ratio 4-1/8 bore Two year warranty Available for most 1984-2017 Harley-Davidson Big Twins in 111, 124 and 143 cubic inch formats
Powerful - 65cc petrol earth auger with 1.2 Liter fuel tank capacity. 3.2HP, 9000rpm for maximum power. Uses 2 stroke oil mixture - 30:1 - which will extend engine life, reduce emissions and run reliably in all weather conditions. Comfortable - Ergonomic design; dual handles for operator control and comfort. Anti-vibration foam grips reduce fatigue. Compact, attractive and easy to operate. Effortless - Easy pull recoil starter for virtually effortless starting. The drill digs no less than 70 pits per hour, and at 8 working hours, it can dig 560 pits in a day, which means it can do more than 30 times as much work as manual work. Versatile - The throttle control system is very popular with operators because it allows simple control of the auger. It has a damper lever to simplify start-up procedures and reduce the possibility of flooding, while the auger brake is designed to automatically stop the auger when it hits a hard underground obstacle. MODEL: EA650G Engine type : 1E48F Power : 2.4kW / 3.2HP Displacement : 65cc Motor type : Gasoline Drill diameter : 30mm - 200mm Fuel Tank Capacity : 1500ml Fuel mixture ratio : 30:1 Weight : 20kg
Merchant Marine Chittagong, a premier ship supply and ship repairing company in the Bangladesh region. Our dedicated technical and supply team is committed to serving ship managers, ship owners, and agents 24/7 at Chittagong Port, Mongla Port, and Payra Port. Our Services Ship Supply / Marine Stores Ship Repairing and Main Engine Overhauling Spare Parts Supply and Export Annual Inspecting and Survey Owner Agent and Crew Change Sludge Disposal, Garbage Cleaning Navigation and Safety Equipment WHY CHOOSE US We take pride in being one of the leading entities in the industry, offering comprehensive services to ship managers, ship owners, and agents 24/7 at key ports such as Chittagong, Mongla, Matarbari Port and Payra. Our dedicated technical and supply team is committed to providing a wide range of services, including the supply of ship stores (deck/engine/electric/safety/provision), lube oil, technical repair jobs (ME/aux engine/pump/motor), spares fabrication, spare parts provision, and annual inspection & calibration. ____________________________ Ensuring customers receive the highest standard of excellence Merchant Marine Chittagong
A&S Construction Machinery Co., Ltd. supplies all types of drive shafts. All the brands of drive shafts we can provide: CAT drive shafts, KOMATSU drive shafts, JOHN DEERE drive shafts, SANY drive shafts, XCMG drive shafts, VOLVO drive shafts, HITACHI drive shafts, SUMITOMO drive shafts, LIEBHERR drive shafts, DOOSAN drive shafts, CASE drive shafts, BOBCAT drive shafts, KUBOTA drive shafts, YANMAR drive shafts, HYUNDAI drive shafts, DAEWOO drive shafts, etc. For other parts of the brands above we can also provide cylinder liners, crankshafts, oil pumps, solenoid valves, solenoid coils, fuel injectors, batteries, radiators, compressors, gaskets and seals, mufflers, manifolds, turbochargers, hydraulic pumps, hydraulic motors, hydraulic valves, hydraulic couplers, bearings, reducers, bearing seats, gears, pulley, sprocket, coupling, drive shaft assembly, brakes, clutches, drive chains, actuators, alternators, cables, controllers, distributors, fuses and relays, harnesses, sensors, switches, gearcases, filters, counterweights, heater and A/C accessories, belts, etc. Contact Us A&S Construction Machinery Co., Ltd.
A&S Construction Machinery Co., Ltd. supplies all types of controllers. All the brands of controllers we can provide: CAT controllers, KOMATSU controllers, JOHN DEERE controllers, SANY controllers, XCMG controllers, VOLVO controllers, HITACHI controllers, SUMITOMO controllers, LIEBHERR controllers, DOOSAN controllers, CASE controllers, BOBCAT controllers, KUBOTA controllers, YANMAR controllers, HYUNDAI controllers, DAEWOO controllers, etc.. For other parts of the brands above we can also provide cylinder liners, crankshafts, oil pumps, solenoid valves, solenoid coils, fuel injectors, batteries, radiators, compressors, gaskets and seals, mufflers, manifolds, turbochargers, hydraulic pumps, hydraulic motors, hydraulic valves, hydraulic couplers, bearings, reducers, bearing seats, gears, pulley, sprocket, coupling, drive shaft assembly, brakes, clutches, drive chains, actuators, alternators, cables, distributors, fuses and relays, harnesses, sensors, switches, gearcases, filters, counterweights, heater and A/C accessories, belts, etc.. Contact Us A&S Construction Machinery Co., Ltd.
A&S Construction Machinery Co., Ltd. supplies all types of gears. All the brands of gears we can provide: CAT gears, KOMATSU gears, JOHN DEERE gears, SANY gears, XCMG gears, VOLVO gears, HITACHI gears, SUMITOMO gears, LIEBHERR gears, DOOSAN gears, CASE gears, BOBCAT gears, KUBOTA gears, YANMAR gears, HYUNDAI gears, DAEWOO gears, etc. For other parts of the brands above we can also provide cylinder liners, crankshafts, oil pumps, solenoid valves, solenoid coils, fuel injectors, batteries, radiators, compressors, gaskets and seals, mufflers, manifolds, turbochargers, hydraulic pumps, hydraulic motors, hydraulic valves, hydraulic couplers, bearings, reducers, bearing seats, pulley, sprocket, coupling, drive shaft assembly, brakes, clutches, drive chains, actuators, alternators, cables, controllers, distributors, fuses and relays, harnesses, sensors, switches, gearcases, filters, counterweights, heater and A/C accessories, belts, etc. Contact Us A&S Construction Machinery Co., Ltd.
A&S Construction Machinery Co., Ltd. supplies all types of Compressors. All the brands of Compressors we can provide: CAT Compressors, KOMATSU Compressors, JOHN DEERE Compressors, SANY Compressors, XCMG Compressors, VOLVO Compressors, HITACHI Compressors, SUMITOMO Compressors, LIEBHERR Compressors, DOOSAN Compressors, CASE Compressors, BOBCAT Compressors, KUBOTA Compressors, YANMAR Compressors, HYUNDAI Compressors, DAEWOO Compressors, etc. For other parts of the brands above we can also provide cylinder liners, crankshafts, oil pumps, solenoid valves, solenoid coils, fuel injectors, batteries, radiators, gaskets and seals, mufflers, manifolds, turbochargers, hydraulic pumps, hydraulic motors, hydraulic valves, hydraulic couplers, bearings, reducers, bearing seats, gears, pulley, sprocket, coupling, drive shaft assembly, brakes, clutches, drive chains, actuators, alternators, cables, controllers, distributors, fuses and relays, harnesses, sensors, switches, gearcases, filters, counterweights, heater and A/C accessories, belts, etc.
