NLB-1800 Rail Bolt Wrench The NLB-1800 Rail bolt wrench is novel in design, compact in structure, small in volume, light in weight, strong in maneuverability, two-stage shock absorption of handle, portable in hand, convenient in getting on and off the track, especially suitable for the regional maintenance operation of track bed where turnout, tunnel, bridge and culvert and other large and medium-sized railway maintenance machinery cannot work. Specification Model NLB-1800 Type Rail Bolt Wrench Material Stainless Steel Dimensions (L x W x H) 830*280*380mm Petrol engine Two stroke petrol engine Rated Revolution 12000r / min Rated power 3.6kw Spindle speed 1130R / min Torque â?¥ 1800n. M
Digital Rail Straight Edge Digital Rail Straight Edge is used for measuring vertical railway line rail abrasion and flank wear it includes reference positioning frame and installed on the framework of reference positioning auxiliary positioning screw and the depth of the rail vertical abrasion side abrasion measured in feet its structure is simple intuitive and accurate measurement data and upper and lower rapidly operator safety its light weight convenient to carry Benefits Digital Rail Straight Measuring Ruler has the advantages of high measuring accuracyeasy to operateLCD digital display etc Specification Model LJZDI Type Digital Straight Edge Material Carbon Steel Dimensions L x W x H 1201224 cm Measurement range 5 Indication error 006 Measuring length 1000
manufacturers Chery Automobile energy type plug-in hybrid engine 1.5T 156 horsepower plug-in hybrid Pure electric cruising range (km) NEDC 100 Maximum power (kW) 240 Maximum torque (N�·m) 545 gearbox 3 gear DHT Length x width x height (mm) 4590x1900x1690 Body structure 5-door 5-seat SUV Maximum speed(km/h) 180 Power consumption per 100 kilometers (kWh/100km) 21.2kWh Electric energy equivalent fuel consumption (L/100km) 1.7 motor type Permanent magnet/synchronous engine model/Intake form SQRE4T15C/turbocharged Number of drive motors dual motor Motor layout Front Battery Type Ternary lithium battery Battery capacity (kWh) 19.27 Battery energy density (Wh/kg) 143.8 gearbox type fixed gear ratio gearbox
Product Description NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. Specification Model NQG-5.8 Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM 4500 r/min Specification of cutting disc �?355x�?25.4 x3.8mm Cutting accuracy Vertical deviation of notch and railâ?¤0.30mm Deviation of bidirectional cutting interfacesâ?¤0. 35mm Cutting time â?¤110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
Product Description NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. Specification Model NQG-5.8 Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM â?¥4500 r/min Specification of cutting disc �?355x�?25.4 x3.8mm Cutting accuracy Vertical deviation of notch and railâ?¤0.30mm Deviation of bidirectional cutting interfacesâ?¤0. 35mm Cutting time â?¤110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
Product Description NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. Specification Model NQG-5.8 Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM 4500 r/min Specification of cutting disc 355x25.4 x3.8mm Cutting accuracy Vertical deviation of notch and rail0.30mm Deviation of bidirectional cutting interfaces0. 35mm Cutting time 110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
Product Description NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. Specification Model NQG-5.8 Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM 4500 r/min Specification of cutting disc 355x25.4 x3.8mm Cutting accuracy Vertical deviation of notch and rail0.30mm Deviation of bidirectional cutting interfaces0. 35mm Cutting time 110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
Product Description NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. Specification Model NQG-5.8 Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM 4500 r/min Specification of cutting disc 355x25.4 x3.8mm Cutting accuracy Vertical deviation of notch and rail0.30mm Deviation of bidirectional cutting interfaces0. 35mm Cutting time 110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
Product Description NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. Specification Model NQG-5.8 Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM â?¥4500 r/min Specification of cutting disc �?355x�?25.4 x3.8mm Cutting accuracy Vertical deviation of notch and railâ?¤0.30mm Deviation of bidirectional cutting interfacesâ?¤0. 35mm Cutting time â?¤110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. PRODUCT SPECIFICATIONS Model NQGâ??5.8 Type Abrasive Rail Saw Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM 4500 r/min Specification of cutting disc 355x 25.4 x3.8mm Cutting accuracy Vertical deviation of notch and rail 0.30mm Deviation of bidirectional cutting interfaces 0. 35mm Cutting time 110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
NQG-5.8 Abrasive Rail Saw NQG-5.8 lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail welding factories. Specification Model NQG-5.8 Type Rail Cutting Machine Material Stainless Steel Dimensions (L x W x H) (mm) 850*480*500mm Engine Single-cylinder, air-cooling two-stroke petrol engine (imported from Sweden K1270R)5.8 kW Cutting disc form Double- layer reinforced wire mesh Linear speed of cutting disc 100 m/s Rated RPM 4500 r/min Specification of cutting disc 355x 25.4 x3.8mm Cutting accuracy Vertical deviation of notch and rail 0.30mm Deviation of bidirectional cutting interfaces 0. 35mm Cutting time 110s( cut off 60kg/m rail) Fuel tank capacity 1.25 L Weight 22kg
manufacturers BYD energy type pure electric electric motor 204 Pure electric cruising range (km) Ministry of Industry and Information Technology 520 Charging time (hours) Fast charging for 0.5 hours and slow charging for 10.2 hours Quick charge capacity (%) 30-80 Maximum power (kW) 150(204Ps) Maximum torque (N�·m) 310 gearbox Electric vehicle single speed gearbox Length x width x height (mm) 4785x1890x1660 Luggage compartment volume (L) 175 Body structure 5 door 5 seat hatchback Maximum speed(km/h) 150 Official 100km acceleration time (s) 10.9 Power consumption per 100 kilometers (kWh/100km) 10.5kWh Electric energy equivalent fuel consumption (L/100km) 1.2 motor type Permanent magnet/synchronous Number of drive motors single motor Motor layout Front Battery Type BYD blade battery Lithium iron phosphate battery Battery capacity (kWh) 50.3-66.7 Battery energy density (Wh/kg) 152
Roots Blower For Sale The Roots blower is a volumetric fan, with impeller end face and front and rear end covers of the fan. The principle is to use two blade shaped rotors to move relative in the cylinder to compress and transport gas in a rotary compressor. This type of blower has a simple structure and is easy to manufacture. It is widely used in aquaculture oxygenation, sewage treatment aeration, cement conveying, and is more suitable for gas conveying and pressurization systems in low pressure situations. It can also be used as a vacuum pump, etc. Type of Roots Blowers for Sale Roots Vacuum Pump Roots vacuum pumps have been applied in petroleum, chemical, plastic, pesticide, turbine rotor dynamic balance, aerospace space simulation and other devices, so they should be vigorously promoted and applied in China. It is also widely used in industries such as petroleum, chemical, metallurgy, and textiles. Rotary Air Blower Small size, large air volume, low noise, and low energy consumption (the rotary blower adopts the principle of operating compressed air, although small in size, it has large air volume, energy saving, and silent operation that other forms of fans cannot compare with.). Smooth operation and convenient installation (for small models, as long as they are properly placed, the vibration is minimal and there is no need to install anti vibration devices, making installation convenient). Resistance to load changes and stable air volume (for example, if the pressure of the sewage treatment aeration tank changes, the load changes, but the air volume changes very little with the pressure change). Equipped with an air chamber for smooth air dissipation (all models are equipped with an air chamber to prevent air pulsation and ensure smooth air dissipation). The material is excellent, the structure is clever, and the performance is stable (all blowers are made of high-quality materials, the structure is exquisite, sturdy and durable, the performance is stable, and there are few long-term failures). Simple maintenance, few faults, and long service life (low speed, low wear, and long service life).
Our CNC turning precision parts are mechanically manufactured and mostly rotationally symmetrical parts that are produced by turning as a manufacturing process. Similarly, we speak of welded parts in welding, laser parts in laser cutting or milled parts in milling. DESCRIPTION OF CNC HARD TURNING What Is CNC Turning? CNC turning is a precise molding process that machines parts by â??turningâ?? a rod material. The rod is fed through to a cutting tool and then material is shaped into a finished product. In the process of making cnc precision turning parts, the cutter is normally fed through a rotating work piece and this rotating work piece typically uses a variety of different angles as well as many different tool shapes. CNC turning is generally used for creating turned metal parts that are symmetrical near their axis. For example a chess pawn would be a part that is symmetrical near its axis. The shapes that you can create using CNC turning vary greatly though and with the addition of other machining processes, the possibilities are endless! While most people use CNC turning to create turned parts that only utilize a single axis, it is also possible to use ones that have more than one axis. This allows for more flexibility. DISTINGUISHES OF TURNING PARTS What Distinguishes Our CNC Turned Parts? Part of our self-image is the continuous investment in our machinery. This is the only way we can guarantee the quality and precision in contract manufacturing for which our customers appreciate us. In the field of CNC turning (Computerized Numeric Control), we rely on automatic lathes and sliding headstock lathes. CNC long turned parts and precision turned parts on our CNC machines can be processed from 3 â?? 600 mm workpiece diameter and a maximum length of 2000 mm. For the production of individual parts or repair work in CNC turning, we also have conventional CNC lathes and automatic lathes with which we can machine turned parts up to a diameter of 400 mm and a maximum length of 1000 mm. If you need any kinds of precise molding, please contact us, as a professional precision molding company, Fangling is willing to offer you high quality products.
Parameter: Maximum swing diameter over bed: 800 mm; Maximum turning length: 3000 mm; Maximum length of two centers: 3000 mm; Spindle bore diameter: 104 mm; Spindle nose type D11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 5.4-720(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.06-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 480 mm; Transverse travel of lower tool rest: 500 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 5900 kg; Machine overall size: 5160x1450x1630 mm;
Parameter: Unit Maximum swing diameter over bed: 800 mm; Maximum turning length: 1500 mm; Maximum length of two centers: 1500 mm; Spindle bore diameter: 104 mm; Spindle nose type D11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 5.4-720(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.06-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 480 mm; Transverse travel of lower tool rest: 500 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4900 kg; Machine overall size: 3660x1450x1630 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 1000 mm; Maximum length of two centers: 1000 mm; Spindle bore diameter: 104 mm; Spindle nose type D11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 5.4-720(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.06-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 480 mm; Transverse travel of lower tool rest: 500 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4200 kg; Machine overall size: 3160x1450x1630 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 3000 mm; Maximum length of two centers: 3000 mm; Spindle bore diameter: 104 mm; Spindle nose type A11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 7.5-1000(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.05-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 350 mm; Transverse travel of lower tool rest: 400 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 5700 kg; Machine overall size: 5160x1380x1450 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 1500 mm; Maximum length of two centers: 1500 mm; Spindle bore diameter: 104 mm; Spindle nose type A11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 7.5-1000(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.05-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 350 mm; Transverse travel of lower tool rest: 400 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4700 kg; Machine overall size: 3660x1380x1450 mm;
Parameter: Unit Maximum swing diameter over bed: 400 mm; Maximum turning length: 1000 mm; Maximum length of two centers: 1000 mm; Spindle bore diameter: 104 mm; Spindle nose type A11 type; Spindle nose taper: 120(1:20) mm; Spindle speed range(clockwise): 7.5-1000(18 steps) rpm; Spindle motor power: 11 kw; Rapid motor power: 1.1 kw; Saddle feed speed: 4000 mm/min; Spindle longitudinal feed per revolution: 0.05-24.3/64 kinds mm/r; Spindle transverse l feed per revolution: 0.03-12.1/64 kinds mm/r; Lead screw pitch: 12 Metric ; Metric threads range(number): 1-240(50 kinds) mm; Inch threads range(number): 1-14(26kinds) t.p.i; Modular threads range(number): 0.5-120(53 kinds) mm; Diametral pitch threads range(number): 1-28(24 kinds) Dp; Tailstock sleeve diameter: 100 mm; Tailstock sleeve traverse: 250 mm; Tailstock center taper hole: MT5 ; Positions of tool rest: 4 positions vertical type pcs; Maximum swing diameter over tool rest: 350 mm; Transverse travel of lower tool rest: 400 mm; Transverse travel of upper tool rest: 200 mm; Section size of tool shank: 25*25 square mm; Machine weight: 4000 kg; Machine overall size: 3160x1380x1450 mm;
