V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Forging hammer, hydraulic forging press, ring rolling machine, steel ball making machine, hot forging machine.
The hydraulic forging hammer is a new energy saving and environmental protection forging hammer. It can save more than 90% energy comparing with the steam forging hammers and the forging hammers with compressor. --roger(at)chinesehammers(dot)com--- The pressure of compressed Nitrogen is constant, and the hammer is operated just by controling the hydraulic system. When you feed blanks, the hydraulic pressure will lift the hammer head. When you hit the blank, the hydraulic pressure will unload fastly and the pressure of compressed Nitrogen and the gravity will drive the hammer head to hit the blank at a very high speed. The hydraulic forging hammer can promote the efficiency and production with good quality. The hammer has safety locking motion so that working is safe and convenient. As further, It can improve the working condition, which is environmental and good for workers. The advantage, structure and design feature of hydraulic forging hammers is as follows, 1;Energy conservation and environmental protection. 2;The operation is convenience,lowering and the act is agility 3;System work safety,it has fully safety locking motion 4;Special structure is more fair and more safety. wooden case.
Electro hydraulic forging hammer The electro hydraulic forging hammer model: 1t, 2t, 3t, 5t wooden case
box type hydraulic rock breaker hammer made in china yantai chengtai construction machinery co.,ltd is a excavator front attachment factory in china ,we specialized in manufacture YTCT hydraulic breaker ,YTCT plate compactor ,YTCT ripper and YTCT bucket ,YTCT quick hitch ,YTCT wood grapple etc front attachment for any brand excavator
****OUR FACTORY ***we are a factory in yantai city,shandong province,China specialized in manufacturing hydraulic breaker ,quick hitch ,ripper ,etc for excavator attachment . OUR FACTORY IN YANTAI CITY,SHANDONG PROVINCE ,CHINA OUR PRODUCT HYDRAULIC HAMMER MOQ 1 SET OEM YES.BECAUSE WE ARE A FACTORY COLOR ANY COLOR COULD DO FOR YOU PAYMENT 30% DEPOSIT ,BALANCE BEFORE SHIPPING ,T/T OR L/C DELIVERY DATE 1-50 SET 1-25DAYS. SHIPPING BY SEA O BY AIR * Yantai Factory Direct Price * Small order is welcome, MOQ 1 set * Nice quality, one year warranty * Chisel diameter from 35-210mm * Breaker suit any brand 0.5-70 ton excavator ALL THE PRICE WITH SPARE PARTS AS BELOW: 1.all the price with wooden box pacakage . 2.all the price with the standard spare parts. ** -----2 chisels ** -----2 oil tube ** -----1 N2 gas bottle. ** -----1 tool box ** -----1 N2 pressure gauge PACKING AND SHIPPING 1.Inner is stretch film, outside is export plywood case or as customer's request 2.Delivery time:Usually 3-7days (1-5sets) after down payment. 3..We can arrange ocean or air transportation according to your request from any port of China. HOW TO CHOOSE OUR BREAKER ? 1. PLEASE LET US KNOW YOUR EXCAVATOR MODEL NUMBER OR WEIGHT OF MACHINE. 2.PLEASE LET US KNOW WHAT COLOR DO YOU NEED FOR BREAKER . 3.PLEASE CHECK THE ABCDE SIZE FOR US ,ARM EAR WIDTH ,PIN DIAMETER AND PIN CENTER TO PIN CENTER SIZE . 4.CHOOSE WHAT TYPE OF HYDRAULIC BREAKRE DO YOU NEED ,THANKS.
The quality inspection of die forgings includes appearance quality inspection and internal quality inspection, including numerous inspection items respectively. The first is the chemical composition inspection, usually based on the smelting before the furnace sampling analysis as. Especially for important or suspect die forgings, some chips can be cut from the forgings and chemical composition can be tested by chemical analysis or spectral analysis. Secondly, the size and shape of die forgings are checked. Visual inspection is a more common method to observe the surface of forgings with the naked eye whether there are folding, cracks, bruises, scars, surface burns and other defects. And the surface of die forgings hidden deep defects, often after heat treatment and cleaning for observation. And its dimension measurement inspection includes length, width and height dimensions; Parallelism and perpendicularity of the plane; The curvature of the axis; Ellipticity of inner and outer circles; Radius of fillet; The concentricity; The included Angle and the misshift, etc. When the die forgings are required to carry out the precise size inspection, in addition to the marking inspection and the special sample can be used, the inspection instrument controlled and analyzed by the computer can be used, or the optical comparator, optical projector can be used for the relevant size inspection, to ensure the accuracy of the inspection results. Surface flaw detection is also a part of the quality inspection of die forgings. The surface quality of membrane acid and base is determined by magnetic particle test and fluorescence test. In addition, there are ultrasonic inspection, low tissue inspection, microscopic inspection, residual stress inspection and so on, each link can not be ignored.
Bearing Housing (for chip cutter) Material : S.S. 304 (Cast Steel)
Bearing Ring (SAE-52100) Forged, Heat Treated, Machined & Ground
Bin Bell (Machined) Cast Steel (IS 1030-1982,Gr.2)
Bowl Top Forgings AISI 316 Forged, Solution Annealed & Proof Machined
Cage Front Forged & Proof Machined Cage Front for High Speed Gear Box
EN - 24 Forged, Hardened & Tempered (248-302BHN) & Proof Machined
Clevis (C-45 Material) Forged, Normalized & Proof Machined (Weight: 550 KG) Load Carrying Capacity 100 T
Compressor Connecting Rod Material : EN 19 Proof Machined & Heat Treated to "T" Condition.
Rupex Coupling Motor Side hub for main hoist of Quay Crane. Material : EN 19 / 42CrMo4, Forged Heat Treated to 280-300 BHN, Finish Machined & Dynamically Balanced.
Crank Shaft C-45 (For Textile Loom Application) Dia. 45 X 3151 mm Long Throw : 80 mm (One Piece Construction)
Fabricated Bracket Folax Cooler (928 S) (For Cement Plant Application) Boiler Quality Plate IS : 2002, Gr.1 for Pull Rod & Movable Frame for Drive Mechanism
