Product details Introduction: This tester is designed to not-destructively measure thisckness of non-magnetic coatings (including paint, enamel, plastic,epoxy, etc.) on iron, steel and aluminum. General Specifications: Conversion of public and imperial units Automatic calibration Compact and easy to carry Power-saving, auto power off Data-hold mode Ergonomic Design Ergonomic design, Easy to use "UNIT" Button Press the "UNIT" button to select dsired unit: mm or mil mil: A unit of length equal to one thousandth of an inch; used to specify thickness(e.g., of sheets or wire) mm: A metric unit of length equal to one thousandth of a meter Low Battery Indicator When the indicator appears on the display, the button cell is low and must be replaced immediately. "TEST" Button 1. Press the "TEST" button to turn on the tester. Press and hold down this button for about 1 second to turn off the tester. 2. Press this "TEST" button to delete the reading on the display, will show"--". PROBE Measuring probe of the tester. Before measurement, place the tester with its probe firmly and in a right angle against the surface to be tested. EM2271,SPECIFICATION Measuring Range 0.0 mm to 2.0 mm, 0 mil to 80 mil Accuracy 2% rdg ±0.1 mm, or 2% rdg ± 4 mil Resolution 0.1 mm/1 mil Power Supply 3V button cell, CR2032 or equivalent, �1pc Size 69�38�20mm Weight About 23g (including button cell)
1 Overview: This heating device is specially designed for the on-line annealing of copper tubes. For the characteristics of continuous heating in the movement and the workpiece being heated is copper, special design should be made for the parameters of the power supply and the inductor in the system design. The whole system is heated by a set of 800KW/6KHZ power supply. The outside of the inductor is made of aluminum closed casing and filled with protective gas (nitrogen) to prevent oxidation and oxidation of the copper pipe. This system has the following characteristics: 1.1 The intermediate frequency power supply is 800KW/6KHz. Due to the high power and high frequency, the power supply design has some special requirements. These will be detailed in the description of the power supply. 1.2 The intermediate frequency power supply and the sensor are all water-cooled, making the equipment small and easy to install. 1.3 Automatic continuous production, the production speed can be automatically adjusted according to different workpiece parameters. 1.4 Production line transmission raceway adopts frequency conversion speed regulation, plus PLC can realize closed-loop control of temperature, speed and power. 2. Process parameters: Copper tube size: Φ9.52�0.37mm; Φ12.7�0.43 mm Copper tube lifting temperature: 700 ° C Roller speed: >200 m/min 3. System equipment operation plan: 3.1 System power selection: The choice of total heating power is 800KW depending on your requirements. 3.2 Choice of program:
Quick DetailsPlace of Origin: Guangdong,China (Mainland)Brand Name: PIngoodModel Number: OEMStandard: ISOMaterial: SteelPackaging & DeliveryPackaging Details: opp bag /cartonDelivery Time: 7 daysShenzhen Pingood Precision Hardware Co. Ltd. is a professional large-scale manufacturer of all types of metal precision parts. Our main products include screw, nut, bolt, CNC parts and related products. We have established a good cooperative relationship with many famous brands in the worldOur company was established in 2000. We are an intelligent plant which have 50 sets of CNC lathes, 70 sets of Bolt Formers machines, 60 sets of Tapping machines. Our factory in strict accordance with the ISO9001 quality management system and ISO14000 management system.All the products are tested by laser testing machine and ROHS tester. The products are fully in conformity with international standards.We hope to cooperate with more customers for mutual development and benefitsBefore the Quotation, please help us to know, as below: cnc brass parts1.Size drawing ( if you have no drawing, please tell us your products detail size and send us your picture.)2.Material (Aluminum, copper, brass, stainless steel, steel, iron, alloy, zinc etc.)3.Quantity (If your quantity reach our MOQ the price will be better)4.Surface treatment (Polishing; Anodize; Nickel, Zinc, Tin, chrome, Silver plating etc.)5.Hardness6.Packing Term
Quick DetailsPlace of Origin:Guangdong, China (Mainland)Brand Name:PIngoodModel Number:OEMStandard:ISOMaterial:SteelPackaging & DeliveryPackaging Details: opp bag /cartonDelivery Time: 7 daysShenzhen Pingood Precision Hardware Co. Ltd. is a professional large-scale manufacturer of all types of metal precision parts. Our main products include screw, nut, bolt, CNC parts and related products. We have established a good cooperative relationship with many famous brands in the worldOur company was established in 2000. We are an intelligent plant which have 50 sets of CNC lathes, 70 sets of Bolt Formers machines, 60 sets of Tapping machines. Our factory in strict accordance with the ISO9001 quality management system and ISO14000 management system.All the products are tested by laser testing machine and ROHS tester. The products are fully in conformity with international standards.We hope to cooperate with more customers for mutual development and benefitsBefore the Quotation, please help us to know, as below: cnc brass parts1.Size drawing ( if you have no drawing, please tell us your products detail size and send us your picture.)2.Material (Aluminum, copper, brass, stainless steel, steel, iron, alloy, zinc etc.)3.Quantity (If your quantity reach our MOQ the price will be better)4.Surface treatment (Polishing; Anodize; Nickel, Zinc, Tin, chrome, Silver plating etc.)5.Hardness6.Packing Term
Quick DetailsPlace of Origin:Guangdong,China (Mainland)Brand Name:PIngoodModel Number:OEMStandard:ISOMaterial:SteelPackaging & DeliveryPackaging Details:opp bag /cartonDelivery Time:7 days Shenzhen Pingood Precision Hardware Co. Ltd. is a professional large-scale manufacturer of all types of metal precision parts. Our main products include screw, nut, bolt, CNC parts and related products. We have established a good cooperative relationship with many famous brands in the worldOur company was established in 2000. We are an intelligent plant which have 50 sets of CNC lathes, 70 sets of Bolt Formers machines, 60 sets of Tapping machines. Our factory in strict accordance nwith the ISO9001 quality management system and ISO14000 management system.All the products are tested by laser testing machine and ROHS tester. The products are fully in conformity with international standards.We hope to cooperate with more customers for mutual development and benefits Before the Quotation, please help us to know, as below: cnc brass parts1.Size drawing ( if you have no drawing, please tell us your products detail size and send us your picture.)2.Material (Aluminum, copper, brass, stainless steel, steel, iron, alloy, zinc etc.)3.Quantity (If your quantity reach our MOQ the price will be better)4.Surface treatment (Polishing; Anodize; Nickel, Zinc, Tin, chrome, Silver plating etc.)5.Hardness6.Packing Term
Quick DetailsPlace of Origin:Guangdong, China (Mainland)Brand Name:PIngoodModel Number:OEMStandard:ISOMaterial:SteelPackaging & DeliveryPackaging Details:opp bag /cartonDelivery Time:7 days Shenzhen Pingood Precision Hardware Co. Ltd. Â is a professional large-scale manufacturer of all types of metal precision parts. Our main products include screw, nut, bolt, CNC parts and related products. We have established a good cooperative relationship with many famous brands in the worldOur company was established in 2000. We are an intelligent plant which have 50 sets of CNC lathes, 70 sets of Bolt Formers machines, 60 sets of Tapping machines. Our factory in strict accordance with the ISO9001 quality management system and ISO14000 management system.All the products are tested by laser testing machine and ROHS tester. The products are fullyin conformity with international standards.We hope to cooperate with more customers for mutual development and benefits Before the Quotation, please help us to know, as below: cnc brass parts1.Size drawing (if you have no drawing, please tell us your products detail size and send us your picture.)2.Material (Aluminum, copper, brass, stainless steel, steel, iron, alloy, zinc etc.)3.Quantity (If your quantity reach our MOQ the price will be better)4.Surface treatment (Polishing; Anodize; Nickel, Zinc, Tin, chrome, Silver plating etc.)5.Hardness6.Packing Term Â
PCD disc CBN tip cutting tools blanks diamond tool segment PCBN is made by high pressure high temperature sintering of cubic boron nitride with a binder phase, and there are mainly tow groups of binders, namely metal binder and ceramic binder. CBN and diamond are very similar in crystal structure,chemical bond and lattice parameters,thus they perform quite similar hardness and strength. In cutting applications, thewear resistance of PCBN exceeds 50 times that of tungsten carbide. If you need any products, do not hesitate to contact PCD PCD(Polycrystalline Diamond)is a synthesized, extremely tough, intergroup mass of randomly orientated diamond particles in a metal matrix. It is produced by sintering together selected diamond particles at high pressure and temperature. 51mm diameter round shape PCD cutting tools PCD blanks 1. The introduction of PCD cutting tool blanks(PCD cutter/ PCD blanks) : PCD cutting tool blanks are composed of diamond powder and tungsten carbide in high temperature and pressure. They have the high hardness and abrasion resistance of nature diamond, and combined with the toughness that of tungsten carbide 2.The Application of PCD cutting tool blanks(PCD cutter/ PCD blanks): Suitable for the machining of non-ferrous metal and alloys, such as aluminum, copper, zinc, as well as wood, ceramics, rubber, plastic, fibre, etc. 3. Some useful tips of PCD cutting tool blanks(PCD cutter/ PCD blanks): The normal shape is round, also could be cut into rectangles, triangles, sectors, etc. as request. The main controlling factor determining PCD grade(the work piece surface finish and the abrasion resistance(tool life) )is the grain size. It is generally accepted that abrasion resistance increases with increased grain size, and the work piece surface finish are increases with the decreasing grain size. The medium grain size PCD blanks are generally used for their ability to strike a balance between good abrasion resistance (tool life) and maintaining good work piece surface finish. The PCD blank is thermally stable up to 750°C, so its better to be welded with silver solder in a very short time, otherwise will cause carbonizing reaction or crack.
Round and square PCD diamond blank PCD piece 51mm diameter round shape PCD cutting tools PCD blanks 1. The introduction of PCD cutting tool blanks(PCD cutter/ PCD blanks) : PCD cutting tool blanks are composed of diamond powder and tungsten carbide in high temperature and pressure. They have the high hardness and abrasion resistance of nature diamond, and combined with the toughness that of tungsten carbide If you need any products, do not hesitate to contact 2. The Application of PCD cutting tool blanks(PCD cutter/ PCD blanks): Suitable for the machining of non-ferrous metal and alloys, such as aluminum, copper, zinc, as well as wood, ceramics, rubber, plastic, fibre, etc. 3. Some useful tips of PCD cutting tool blanks(PCD cutter/ PCD blanks): The normal shape is round, also could be cut into rectangles, triangles, sectors, etc. as request. The main controlling factor determining PCD grade(the work piece surface finish and the abrasion resistance(tool life) )is the grain size. It is generally accepted that abrasion resistance increases with increased grain size, and the work piece surface finish are increases with the decreasing grain size. The medium grain size PCD blanks are generally used for their ability to strike a balance between good abrasion resistance (tool life) and maintaining good work piece surface finish. The PCD blank is thermally stable up to 750C, so its better to be welded with silver solder in a very short time, otherwise will cause carbonizing reaction or crack. 26 years experience in the cutting tool industry, factory in Chengdu, China Grinding and inspection equipments imported from UK, Germany, Japan Inspection in every process to ensure 100% qualified World-class technical team and R&D capacity Pass ISO, Germany TUV and Swiss SGS certificates Samples free for testing
crankshaft CBN grinding wheel crankshaft CBN grinding wheel with high speed and high precision control standard can equip with various high precision CNC crankshaft/ camshaft grinding machines. It suitable for high efficient, heavy grinding of crankshaft pin grinding, journal grinding. Steel: 20Crã??GCr15ã?? CF53ã??45# steel, 55#steel, 80 Bhigh carbon steel. Applicable grinding machine: NAXOS (NOXOS-UNION ,P310*1250, GF70) , TOYODA (GCS63 GL5P-63 GL6P-100 GCH120B GC32M-63 GCH63B GL63M-T), JUNKER ( JUCAM5002/10, JUCAM500, JUCRANK5000, 6000), SCHAUDT (CF41, CF61, ZEUSMX,ZXII, etc) . PCD tools for piston processing Our PCD tools are successfully used in many automobile and engineering industries for milling and grooving aluminum and Non-Ferrous materials. PCD mold milling cutter is used for rough,fine machining of piston pin hole,hole and chamfer at the bottom of the hole. PCD end milling cutter for rough finish machining piston top platform.PCD grooving /slot cutter for finishing machining ring grooves, etc. * CBN internal grinding wheel for hydraulic tappet of automobile motor CBN internal grinding wheel with high efficiency, good workpiece consistency and long life time are used for hydraulic tappet of automobile motor diamond honing stone for auto parts processing Diamond honing stone is mainly used for fine grinding engine Pump Body, Hydraulic Cylinder Bore, Hydraulic Pump Inner Bore, Cylinder Block, Valve,Air Cylinder Hole Of Compressor, etc. *Vitrified CBN slotting grinding wheels for cutting and fine grinding of sealing components and hydraulic parts , electroplated grinding wheel for camshaft grinding, diamond dressing roller and resin diamond grinding disc, etc. Our diamond and CBN tools are widely used in the automotive industry . We provide some solutions to some leading names in the automotive sector including:BMW, Ford, Toyota, Volovo,Beijing Hyundai,Mitsubishi and others.
Appearance: Colorless transparent liquid Color(Pt-Co) â?¤25 Molecular Weight 221.4 Specific Gravity (Ï?20°C, g/cm3): 0.946 Refractive Index (nD25) 1.420 Boiling Point (°C) 217 Flash Point (°C) 98 Purity (%) â?¥97.0 Applicationsï¼? ï??Coatings, Adhesives and Sealants The aminosilane is an excellent adhesion promoter in acrylic coatings, adhesives and sealants. With polysulfide, urethane, RTV silicones, epoxy, nitrile, phenol formaldehyde resin, adhesives and sealants, the product improves pigment dispersion and maximizes adhesion to glass, aluminum and steel. ï??Fiber glass Reinforcement In fiberglass reinforced thermosetting plastics and thermoplastics, the aminosilane enhances the flexural, tensile and interlaminar shearing strengths before and after exposure to humidity. This product greatly improves wet electrical properties. Fiberglass reinforced thermoplastics, polyamides, polyesters and polycarbonates exhibit increased flexural and tensile strengths before and after wet exposure when this silane is used. ï??Glass Fiber and Mineral Wool Insulation As a phenolic resin binder additive, the aminosilane imparts moisture resistance and allows recovery after compression ï??Mineral Filler and Resin Systems The aminosilane maximizes the physical and electrical properties of mineral-filled phenolics, polyester resin, epoxies, polyamides, polycarbonate and a host of other thermoset and thermoplastic composites. Wettability and dispersibility of filler in the polymer matrix are also improved. ï??Foundry Application In shell molding, the aminosilane strengthens the bond between the phenolic binder and foundry sand. ï?? Grinding Wheel Manufacture The aminosilane promotes an improved, water resistant bond between the abrasive grit and phenolic resin binder. ï??Wood plastic composite production The mechanical properties of composites made of wood meal, such as impact strength, bending strength and bending modulus, will be improved after these composites are processed with this product. Packing/Storage 25 kg, 200kg plastic or iron drum
4WD Foxwing Awning Product Description The 4WD Foxwing Awning provides the best shade solution for you and your family when you're out travelling and enjoying the outdoor. It is a brilliantly designed and easy to operate swing out awning that will cover the side and rear of your vehicle, providing 270 degrees of shade. The Foxwing Awning can be set up and packed down in minutes for you to enjoy more of your day. 4WD Foxwing Awning, Car Awning, Foxwing Awning on sale Car Side Awning Features Car Side Awning can offer shade for campers when camping,usually used together with car roof top tents Poles are light-weight and adjustable,apply to almost cars High quality and waterproof fabric support to use in any rough weather Awning walls are optional as accessory to make awning houses Quick & easy to set up and pack down ( can be set up by 1 person) Car Side Awning Specification Fabric Optional 280g poly-cotton rip-stop canvas/420D Oxford Cover Heavy duty 1000D PVC Parts All metal assemble and mounting parts are made by stainless steel, all eyelets on tent are copper to avoid rusting Pole Aluminum alloy telescopic pole dia 22/25mm, Height 120cm - 200cm Color Optional Khaki/Green/Grey Size Diameter 2m / Diameter 2.5m Optional Awning walls Gross Weight 11kg/12kg Package Size 212*15*9cm / 262*15*9cm
The best power banks for mobile of 2018: portable chargers to keep your gadgets going Do find your phone battery often dies before the end of the day. Then buy a best Power Bank Charger so you can keep it pumped up with battery while on the go. We've put together a selection of great portable power banks that you can get right now. We've got options no matter what you're looking for. Whether you`re looking for a high capacity battery, slim design, lots of ports or something that can charge up both your phone and your laptop at the same time, we`ve got you covered. High quality and cheap power banks for great capacity. Welcome inquiry. Best Power Bank for Mobile Parameters Model : p07 Input : DC 5V/2.4A Output : DC 5V-1.5A/2.4A Capacity : 11000mAh Rated energy : 40.7 Wh Best Power Bank Charger introduction It`s so light and handy , with a simple style of fashion , easy to carry when you go out. Its shell uses Aluminum materials ; shock-resistant and resilient safety protection . High density and high capacity , capable of storing large volumes of power ; high conversion rate , providing sufficient power to the phone , saving energy and time . Uses advanced battery real-voltage tracking technology ; 4 LED lights to indicate remaining power so that you can always know how much power remains . Uses highly integrated IC chips , providing protection against overcharging , overdischarge , overcurrent and short circuit , etc ; safe and secure. Looking for ideal Best Power Bank for Mobile Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Cheap Power Bank are quality guaranteed. We are China Origin Factory of Best Power Bank Charger. If you have any question, please feel free to contact us.
If mobile turn down is an all-too-familiar scenario, a best portable charger (otherwise known as a Power Bank mobile charger) would be a wise investment. for that matter an extra power bank mobile 20000mah will see you through . An excellent capacity of 20,000mAh, which should give your iPhone X, for example, around seven full charges, bearing in mind efficiency. Two USB ports give 2.4A output individually, or can combine for a speedy 3.4A, so it`s good for charging multiple devices at once. Power Bank 20000mah description Exquisite quality High safety Quick charge Model : p09 Input : DC 5V/2.4A Output : DC 5V/2.4A Capacity : 20000mAh Dimension : 76*17.5*158mm Rated energy : 74.0 Wh Best Portable Charger introduction Founder modelling , fashion simple , portable , go out easily . Shell using aluminum alloy material , impact resistant , good toughness and safety protection . High density , high capacity , store a lot of energy , high conversion rate , for the hand to provide enough power , energy conservation and save time . Advanced battery voltage real tracking technology , precise digital power , according to remind power status . High level of integration of IC chip , over charge , over discharge , over current and shout circuit protection function . Looking for ideal Best Portable Charger Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Power Bank 20000mah are quality guaranteed. We are China Origin Factory of Power Bank Mobile Charger. If you have any question, please feel free to contact us.
Located in shijiazhuang city hebei province China. Hebei baisiwei import&export Co., ltd. Can provide you Power Bank lowest price with good performance. Whether you're a teenager glued to your phone, a tech savvy individual with a hundred tabs open, or a businessman on a conference call, sometimes you can run out of power when we need it most. Thankfully the battery Power Bank will keep you powered during all those crucial moments. Stay Charged For When You Need It Most. Whether power bank 10000 or other capacity. Turn to us definitely you will find one meet your request. Battery Power Bank description USB X2 Smart and safe fashion Anodized aluminum cover amrican silergyic synchronous rectification output , working efficiency is higher than 91% . no product heat when it works 10000mAh Exquisite quality High safety Quick charge Power Bank 10000 Parameters Model : p08 Input : 5V/2.4A Output : 5V/2.4A Capacity : 10000mAh Rated energy : 37.0 Wh Looking for ideal Power Bank Lowest Price Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Battery Power Bank are quality guaranteed. We are China Origin Factory of Power Bank 10000. If you have any question, please feel free to contact us.
Want to buy the best Power Bank for smartphone. but don`t want to pay for all the extra features. Then contact us. You can get portable power bank, iphone power bank high quality with competitive price. And if your smartphone is compatible with Quick Charge 3.0 then there are few faster chargers out there. It weighs 275g, so for the power it provides, it`s not too hefty. It`s USB-C compatible, too. The charger itself can also be powered up by a Lightning Cable, which means you may only have to carry one cable around with you, device-permitting. There`s a built-in flashlight ?? you never know when you might need it ?? and although it`s not the best looking device around, it`s still perfectly portable. The power button lights up different colors to indicate battery level. Portable Power Bank description Exquisite quality High safety Quick charge Model : p09 Input : DC 5V/2.4A Output : DC 5V/2.4A Capacity : 20000mAh Dimension : 76*17.5*158mm Rated energy : 74.0 Wh Best Power Bank for Smartphone introduction Founder modelling , fashion simple , portable , go out easily . Shell using aluminum alloy material , impact resistant , good toughness and safety protection . High density , high capacity , store a lot of energy , high conversion rate , for the hand to provide enough power , energy conservation and save time . Advanced battery voltage real tracking technology , precise digital power , according to remind power status . High level of integration of IC chip , over charge , over discharge , over current and shout circuit protection function . Looking for ideal Iphone Power Bank Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Portable Power Bank are quality guaranteed. We are China Origin Factory of Best Power Bank for Smartphone. If you have any question, please feel free to contact us.
Offers great slim Power Bank. and it's one of the cheapest options on our product list yet boasts a substantial 10,000mAh cell inside. It may be heavy, but it have the thinnest type, making it the great device to slip into your back pocket when you're out and about. You'll want to grab a cable to go with it. Choose our Ultra slim and easy to carry mobile phone power bank. Good efficiency for energy storage Good memory effect , low power consumption , ensure high capacity Intelligent identification When the digital product connects with the cell phone power bank , it can automatically identify and charge to the power bank . plug and charge , intelligent and convenient if the digital product is not disconnected after fully charged , the power bank can automatically identify , initiate over-charge protection and stop outputs ,which can save the power consumption . Slim Mobile Phone Power Bank description USB X2 Smart and safe fashion Anodized aluminum cover amrican silergyic synchronous rectification output , working efficiency is higher than 91% . no product heat when it works 10000mAh Exquisite quality High safety Quick charge Parameters Model : p08 Input : 5V/2.4A Output : 5V/2.4A Capacity : 10000mAh Rated energy : 37.0 Wh Looking for ideal Slim Power Bank Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Cell Phone Power Bank are quality guaranteed. We are China Origin Factory of Mobile Phone Power Bank. If you have any question, please feel free to contact us.
2018 Power Bank for sale, large capacity. Power Bank 11000mAh Super Thin battery bank for mobile Charger. Compatible with all Apple and Android smartphones, tablets and other USB charged devices with a 5V charge input. The power bank has smart LED lights on the top panel lending it an element of beauty. While these beautiful lights will light up your world; they will also indicate to you the amount of charge left in the power bank. Between 71% to 100% the LED lights will turn green; between 31% to 70% you will see blue lights and low power between 1% - 30% will be indicated to you through red lights. Now that`s what we call beauty and brains. Power Bank 11000mah Parameters Model : p07 Input : DC 5V/2.4A Output : DC 5V-1.5A/2.4A Capacity : 11000mAh Rated energy : 40.7 Wh Product introduction It`s so light and handy , with a simple style of fashion , easy to carry when you go out. Its shell uses Aluminum materials ; shock-resistant and resilient safety protection . High density and high capacity , capable of storing large volumes of power ; high conversion rate , providing sufficient power to the phone , saving energy and time . Uses advanced battery real-voltage tracking technology ; 4 LED lights to indicate remaining power so that you can always know how much power remains . Uses highly integrated IC chips , providing protection against overcharging , overdischarge , overcurrent and short circuit , etc ; safe and secure. Looking for ideal Power Bank Sale Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Power Bank 11000mah are quality guaranteed. We are China Origin Factory of Battery Bank for Mobile. If you have any question, please feel free to contact us.
This USB Type C Cable is 4-foot.It makes use of a braided-nylon design and attractive metallic housing, the latter of which adds durability. The cable is safe to use with USB-C smartphones.It also has a current output of 3.0A, ensuring a quick charge when paired with a 3.0A Wall Charger.This cable is great. Solid, molded USB Type Cconnector, durable, flexible. The usb type c to usb type a cable is durable.Enjoy a topnotch aluminum wire with a premium nylon braided jacket that can bear 5000+ bending tests for extra protection and durability.Extra-durable 10,000+ insertion lifespan: Freely plug in and unplug your devices without worrying of tearing the cable thanks to the connector's unibody design that's made to outlast over 10,000 insertions.And dark fiber for a cleaner look: With its dark gray nylon fabric, the cable stays clean and won't pick up dirt as easily as other light-colored cables. Product description Charge transmission in one High-purity copper wire core , high current 3.1A output TPE environmentally friendly materials , feel soft Brushed appearance , non-slip , difficult to wound Zinc alloy interface material , solid , anti-oxidation Looking for ideal Usb Type C to Usb Cables Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Best Usb Type C Cable are quality guaranteed. We are China Origin Factory of Usb Type C to Usb. If you have any question, please feel free to contact us.
The USB Type C vs Micro USB Cable has a metal housing that will be aesthetically pleasing while dispersing heat more efficiently.There is a 56kΩ resistor keeping things safe in there. The best usb c cable is 3.3 feet long and supports USB 3.0 and can charge at 3.3 amps. The usb type c smartphone cable is a good-looking, well-made cable.It is made of nylon fiber and aluminum ports. It measures 3.3 feet, and it is built on the USB 3.0 standard,which means those transfer speeds can go up to 5 GB/s. Best Usb Type C Cable description A , Surface woven nylon material ,easy to cope with tension , bending , swing and other harsh tests , solid , durable , dirt resistant , anti winding . B , Metal integrated plug design , concise appearance , safe and reliable . C , High quality tin plated copper core , transmission charging two in one , charging fast , stable data transmission . Environment protection wire , strong tensile properly , metal connectors are more durable . Data weave cable Looking for ideal Micro Type C Usb Cable Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Best Usb C Cable are quality guaranteed. We are China Origin Factory of Usb Type C Smartphone Cable. If you have any question, please feel free to contact us.
This new USB Type C Cable measures at 6.6-foot.And it makes use of a braided-nylon design and attractive metallic housing, the latter of which adds durability. The USB Type C to usb a cable offers a Type-C to Type-A connection and both are reversible.It support fast charging - delivering up to 2.4A - and it can also handle data syncing at up to 480Mbps. The type c cables has a USB-C connector on one end, and a USB-A 2.4 connector on the other. It can deliver up to 2.4A of power. The design is minimalist, with slim connectors, which makes it easy to plug in. The necks are also reinforced. New Usb Type C Cable Product description Aviation aluminum shell , integrated molding , precision adapter interface , plug effort . High purity copper core , each piece of copper wire through tin plating , anti oxidation and anti interference to prolong the service life and ensure the integrity of data signal transmission , durable . Nylon woven bag is , fashion environmental protection , tensile and durable refused to wrap . Charge transfer both no error , charging / data transfer synchronization . Looking for ideal New Usb Type C Cable Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Usb Type C Cables are quality guaranteed. We are China Origin Factory of Type C Cables. If you have any question, please feel free to contact us.
