Mine detection cable is mainly used in various oil and gas Wells with Oil well wax removal, viscosity reduction and coagulation reduction, coring and well logging, perforation etc., can also be used in ocean research and river, harbor, water conservancy hydrological measurement, as well as coal field geological prospecting, geothermal well logging, etc.,The detection cable is connected with the sensor and the signal terminal, which has a strong anti-interference signal transmission function.
Product Introduction SANDI AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-750VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface (Optional)
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Power supply cables.
Cat 6 Cable
PVC Flexible Cable
Cable Tray & Trunking
Submersible Flat Cables
Variety Part No Color 220 7521B - 7521R 325 7522B - 7522R 440 7523B - 7523R
Switching power supply, cable ties, insulated terminals, connectors.OEM
C to lightning Cable. Fast charging Support .
PA(NYLON) UNFILLED. IT COMES FROM AUTOMOTIVE INDUSTRY, WE COULD SUPPLY 40TONS EACH MONTH.
This product is made of high quality oxygen-free copper conductors, fluorinated plastics, Silicone rubber resistant to high / low quality materials as insulation and sheathing materials, Has good heat resistance, heat aging resistance and excellent electrical properties, Meet the conditions for saft operation under the particularity of wire and cable, and provides High cable life and improve the economic and social benefits.
Power supplies, cable accesories tools , cable markers , pcb terminal blocks , cable ties..
Jet fuel and diesel Pattimura Gelora Indonesia, We are currently also providing diesel fuel or A1 jet fuel for commercial aircraft needs for your company or airline needs we can discuss it on whatsapp.
1. Aviation Jet Fuel A1 2. Aviation Jet Fuel JP 54 3. EN590 10 ppm FOB Rotterdam, Fujairah, Houston Minimum 1,000,000 bbl Maximum 5,000,000 bbl No upper limit PROCEDURE ------------------ TRANSACTION PROCEDURES FOR FOB DELIVERY 1. Buyer accepts seller working procedure and issues ICPO with company registration certificate alongside copy of passport page 2. Seller issues commercial invoice (CI), Buyer signs and returns back commercial invoice. 3. Seller issue TSR with GPS coordinate to Buyer Company, 4. Buyer contacts the Seller's storage facility for tank extension to enable Buyer approval to gain access to the facility and execute the Quality & Quantity Inspection in Seller Tank Farm for FRESH Analytical Report/Result by SGS. 5. After successful DIP test, (NCNDA/IMFPA) will be signed by all parties. 6. Seller injects product into Buyers vessel or injects into Buyers tanks Buyer or buyer take over the storage tanks, within maximum 48 hours Buyer pays via MT 103/TT for the spot transaction and seller issues all export documents to buyer. 7. Upon conclusion of first lift transaction seller pays all intermediaries involved in the Transaction. Payment Terms : LC / SBLC / MT 103/TT ---------------------------------------------------------------------- Commodity: Bonny Light Crude Oil (BLCO) Grade: NNPC STANDARD Origin: NIGERIA BLCO Quantity: Initial 1 million or 2 million barrels. Contract: 1year + 2 further years rolling Term: SPOT LIFT / OFF OPEC Price: Dated Brent 3days Before & 3days after the bill of lading $12 Less $5 GROSS $9:00 to buyer, $4:00 to buyer/seller mandate/agents, $1:00 to consultant/handler.
SpO2 cables are specifically designed to connect the SpO2 sensor, typically placed on a patient's finger or earlobe, to the monitoring device. These cables transmit the optical signals captured by the sensor to the monitor, where the data is processed and displayed as oxygen saturation levels.
Medical cable assembly for electrosurgical pencil
Runthrough Ns Extra Floppy Tw-as418xa Runthrough Ns Floppy Tw-as418fa Runthrough Ns Hypercoat Tw-ds418fh Runthrough Ns Intermediate Tw-ds418ia
Length Positive 12 Inches 7601 15 Inches 7602 18 Inches 7603
