CASR No. 127-19-5 Pharmacopoeia / DMF : USDMF, Ph.Eur, CDMF BET Test Limit : 2.0 EU/ml MLT Test (TAMC) Limit : 100 cfu/ml MLT Test (TYMC) Limit: 10 cfu/ml For price, specifications and other details please contact us.
CASR No. 872-50-4 Pharmacopoeia / DMF : USP-NF, Ph.Eur BET Test Limit : 2.5 EU/ml MLT Test (TAMC) Limit : 100cfu/ml MLT Test (TYMC) Limit: 10 cfu/ml For price, specifications and other details please contact us
CASR No. 25322-68-3 Pharmacopoeia / DMF : USP-NF, Ph.Eur BET Test Limit : 2.5 EU/ml MLT Test (TAMC) Limit : 100 cfu/ml MLT Test (TYMC) Limit: 10 cfu/ml. For price, specifications and other details please contact us.
CASR No. 7447-40-7 Pharmacopoeia / DMF : USP, Ph.Eur, BP, IP BET Test Limit : 2.5 EU/g MLT Test (TAMC) Limit : 100 cfu/g MLT Test (TYMC) Limit: 10 cfu/g For price, specifications and other details please contact us
CASR No. 7778-77-0 Pharmacopoeia / DMF : USP-NF, Ph.Eur BET Test Limit : 2.5 EU/mg MLT Test (TAMC) Limit : 100cfu/g MLT Test (TYMC) Limit: 10 cfu/g. For price, specifications and other details please contact us.
CASR No. 6131-90-4 Pharmacopoeia / DMF : USP, Ph.Eur , IP, BP BET Test Limit : 0.5 EU/mg MLT Test (TAMC) Limit : 100 cfu/g MLT Test (TYMC) Limit: 10 cfu/g For price, specifications and other details please contact us
CASR No. 7631-90-5 Pharmacopoeia / DMF : JP, CDMF BET Test Limit : 6.0 EU/g MLT Test (TAMC) Limit : 100 cfu/g MLT Test (TYMC) Limit: 100 cfu/g For price, specifications and other details please contact us
CASR No. 7558-80-7 Pharmacopoeia / DMF : USP, BP, IP BET Test Limit : 2.5 EU/g MLT Test (TAMC) Limit : 100 cfu/g MLT Test (TYMC) Limit: 10 cfu/g For price, specifications and other details please contact us
CASR No. 6106-24-7 Pharmacopoeia / DMF : USP-NF BET Test Limit : 2.5 EU/g MLT Test (TAMC) Limit : 100 cfu/g MLT Test (TYMC) Limit: 10 cfu/g. For price, specifications and other details please contact us.
CASR No. 110-15-6 Pharmacopoeia / DMF : USP-NF, CDMF BET Test Limit : 2.5 EU/g MLT Test (TAMC) Limit : 100 cfu/g MLT Test (TYMC) Limit: 10 cfu/g For price, specifications and other details please contact us
CASR No. 102-71-6 Pharmacopoeia / DMF : USP-NF, Ph.Eur, CDMF BET Test Limit : 0.5 EU/mg MLT Test (TAMC) Limit : 100 cfu/ml MLT Test (TYMC) Limit: 10 cfu/ml For price, specifications and other details please contact us
We supply different engine parts of Locomotive Engines. Few of the parts are mentioned here- insert bearings set bush wrist pin bush HP Piston inlet valve discharge valve low pressure compression ring low pressure oil ring high pressure compression ring high pressure oil ring Nut self locking Blade retainer SS bolt Locking Key Bolt shroud Bolt OIL SEAL For price, specifications and more details please contact us
Available in sizes 3/4" through 3 " up to 15,000 PSI non-stock cold working pressure, our Swivel Joints offer the following features. Minimum flow restriction Heavy duty hex head style ball loading plug Grease retainer ring (ensures clean ball race) Standard packing units Superior hardened ball races ensure uniform surface hardness and depth for longer life under severe thrust and radial loading Standard Swivel Joints are provided with API line pipe threads. Other end connections are available on request Available for standard and sour service All sizes are available in 8 styles, for 360 rotation in 1, 2 or 3 planes. For price and specification please contact us
Key attributes Other attributes Brand Name All Brands Available Processor Manufacture custom Memory Capacity custom Processor Type custom Graphics Card Type custom Hard Drive Capacity 200GB,500gb, othres Screen Size Other Display Ratio 15:09, other Display resolution 1280*800, other Plugs Type US,UK,JP, EU, others Hard Drive Type SSD, custom Video Memory Type Hbm2,other Operating System Window- 10, other Processor Main Frequency 2.10ghz, other Processor Core Hexa Core PPI 261 Refresh Rate 165Hz WLAN / Keyboard language English, other Private Mold no Appearance No scratch Grade A+ ( Almost new ) Accessories Without accessories Model Number All Models Available Product name Used Laptops Packaging and delivery Packaging Details as per customer's want Port Bangkok Package Type: as per customer's want attribute-list Supply Ability 100000 Piece/Pieces per Month Product information Model HP Probook 840 G5 CPU Intel Core i5 8th Graphics AMD Radeon RX 540 Display pixel 1366*768(14.1'') Camera Dedicated Card Operating System Windows10 Battery 3-cell lithium battery Colour Silver Size 326-234*17.9mm Weight 1.48kg Hard disk capacity 8G+256GB Interface 2xUSB, USB Type-C hdmi Headphone/Microphone 2 in 1 RJ45 SIM card slot Expansion dock interface Packaging and delivery Packaging Details Note: Neutral brown craft box for each unit K=A strengthens the export standard outer box Single package size: 41*9.5*36.4 cm FCL size: 61.5*43*38.5 cm 6/box Box weight: (depending on item) Package Type: Note: Neutral brown craft box for each unit K=A strengthens the export standard outer box Single package size: 41*9.5*36.4 cm FCL size: 61.5*43*38.5 cm 6/box Box weight: (depending on item)
Product Details: Minimum Order Quantity 200 Piece Frequency 860-960MHz Material pvc/metal/pc/pet Chip Alien H3 ISO Protocol EPC Class 1 Gen2 ISO 18000-6C Operating Frequency 65-868MHz (EU)/900-928MHz (US)/952-955MHz (JP)IC Type Alien Higgs 3 Memory EPC 96bit User: 512bit UID : 64bit Data Retention 50 years We are offering RFID Asset Tag to our clients.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".