Theaoson zinc coating spray is composed of aerosol can, aerosol valve, paint liquid and propellant. This product uses bright silver powder imported from Germany. The color of the paint film produced after use has the same high-gloss galvanized color as the galvanized parts, it has the same color as the galvanized color that fades with the exposure time, so that there is no color difference in the repaired part coated on the galvanized part. Features High-gloss bright zinc Color consistent with galvanized parts Good atomization, easy to use Application It is suitable for color changing and anti-corrosion treatment of stainless steel, carbon steel, galvanized parts and other metal parts. Base material to prepare Clean the oil, dust and water stains thoroughly before use, and polish or spray primer on the base material if necessary. Instructions: Before use, you must shake up, down, left, and right, and continue to shake the can for about 1 minute after hearing the sound of glass to ensure that the paint liquid is fully mixed and even. 15 ~ 30cm away from the surface of the object to be sprayed, press the nozzle with the index finger to spray uniformly back and forth. When a small amount of remaining liquid cannot be sprayed, please rotate the nozzle 180 �° and spray again. If spraying is not finished one time, put the can upside down before storage, press the nozzle for about three seconds, and clean the nozzle to prevent plugging. Ending working After spraying, it should be placed in a clean and ventilated environment for about 12 hours. If it is not sprayed, the remaining material needs to be kept away from the light, and avoid being near fire sources. The solution of normal problem 1. Paint film whitening: It is recommended to avoid rainy days (especially high temperature and high humidity) and the next day after continuous rain. 2. Shut up: shake evenly and spray for 3 seconds or change nozzle. 3. Spray up: low temperatures suggest using 50 â?? warm water to heat up, one-time finish spray, spray avoid angle 45 degrees. 4. Flow: use the correct spraying distance (15-25cm) and spray movement speed (30-60cm/s) to avoid a thick spray. 5. Bite bottom: remove the bottom part of the bite, fill the bottom ash, and then spray the paint after the coating is dry and flat. Attention Keep away from children, please work in the air. If swallowed, you should immediately cause vomiting and seek medical advice. Spray must be kept in aerosol cans are vertical and horizontal angle of no less than 45 �°. Flammable, pressure vessel, do not use near fire source. The weight changes over time, which is normal, and the attrition rate is less than 2%/ year.
Over the years, we have emerged as one-stop destination for acquiring Parasol Paint and Varnish Removers at leading market prices! We strive to deliver powerful and high performance paint and varnish remover that is precisely developed in line with stated quality norms. We are noted Manufacturer, Exporter & Supplier of Parasol Paint and Varnish Removers and assure time bound deliveries. More about Parasol Paint and Varnish Removers It can effectively use to strip paint and varnish from wooden surface like old furniture & from metal surface like Automobile bodies e.g. car, bus, truck, auto, tractor, etc. & home appliances like refrigerators, cupboards & fans etc. & employed in wide array of industrial and household applications such as paint shops, workshops, garages, railways, defense, shipping industries & at home. These unique product offer impressive performance on almost all types of paint system like two pack wood finishes, air drying & baking industrial finishes like melaminised, alkyds, polyamides, polyurethane, polyester & powder coating. The main characteristic properties of PARASOL is it can dilute with NC thinner with almost no loss in performance characteristic when apply on metals. This is a significant benefit to user as cost & labor saving can be achieved while maintaining or even improving the stripping performance. PACKING : 500g, 1Kg & bulk. Packaging Details 500g, 1Kg, Bulk packing also available. Additional Information Specifications PACKING : 500g, 1Kg & bulk.
PAINT REFILL DME Bottle filled with 300ml mix of solvents, propellants and additives. It is compatible with most paints: acrylic, nitro-acrylic, nitro-synthetic, nitrocellulose. The reseller adds the paint according to the required color. In case of special filling the color can slightly change. We recommend using the product soon after filling the paint
It is the enamel that makes surfaces bright and visible from a distance, even in the absence of light. The fluorescent effect is brought out by applying AMBRO-SOL FLUORESCENT on a white background. It dries to the touch in roughly 15 minutes and dries fully in roughly 24 hours. Sku : V400FLUOR
A spray paint for marking masonry, pavements, asphalt, cement and wood. It is resistant to weathering and wear. It is available in fluorescent colors. The product comes with a special 360 valve, so it can be used in any position.
Ideal for creating general parking signs and signaling danger zones. To make visible the terms of reference such as siting, excavation, demarcation of maintenance works. It is resistant to weathering and chemicals. It can be used on numerous surfaces such as cement, asphalt, glass, wood, synthetic materials. Lines of high precision can be made with this product. The width of the line can vary from 4 to 6 inches depending on the setting. The length varies depending on the traveling speed and the porosity of the surface: 40-50 m.
It is a high quality enamel with a modified silicone resin base, which allows you to renew all surfaces normally exposed to high temperatures. Heat resistant up to 300 C-700 C (check the Technical data sheet). Application: parts of heaters, stoves, ovens, chimney flues, barbecues, fire screens, motorcycle mufflers, etc. don't expose in direct contact with flames. Important: to obtain an optimal and long lasting result it is necessary for the painted parts to be exposed even if only once, to a temperature of at least 180 ' C; any less will make the hardening and adhesion of the enamel only partial. Clean carefully the surface before application and shake vigorously the can. After use, it's advisable to spray for 2/3 seconds with the spray upside down, to avoid the block of the nozzle. Sku:V400TEMP
It's a professional enamel spray ideal for for the paiting of rims wheels of motorcycles and cars. Thanks to its textured / embossed fi nish, this special paint is specifi c for repainting or renewing bumpers, side panels and spoilers. Sku:V400FAS
A metallic enamel that has a particular brightness that looks similar to a mirror. It is adhesive and can be used on any material that is not non-stick (Polyethylene, etc..). Ambro-Sol Leafing is designed for indoor/outdoor use to brighten different surfaces and objects such as frames, furniture, iron, vases, mask, cups, medals, Christmas ornaments, etc. It is dry to the touch approximately 30 minutes after use and its completely dry approximately 1 hour after application. It does not provide protection from abrasions. Once applied handle with care. Sku:V400MET
It's a professional enamel spray that is resistant to scratches, alcohol and gasoline. Ideal for painting tractors and agriculture machines. Before applying this paint it is mandatory to use the suitable primer (V400PRIMER3 or V400PRIMER5) Sku : V400CAR
A special paint that temporarily changes the color of a surface. It can be used on non-porous surfaces. It creates a decorative, protective removable film and has a soft touch effect. The original surface remains intact after the painted surface has been removed. It can be used on cars, sports gear, furnishings and more. To apply, vigorously shake the bottle for at least 1 minute, until the marbles inside the can move freely. Carefully clean the surface before application. Keep a distance of 20-30cm/8-1 2in. Apply 4 to 5 crossed layers (horizontal and vertical), each one every 10-15 minutes. It will be completely dry approximately 2 hours after application
It's the enamel with antiquing effect for internal and external, based on lamellar micaceous iron-oxide, particularly suitable for the protection from the elements and the decoration of internal and external furnishing. The use of special corrosion inhibitors and the possibility of applying high thicknes-ses, allow to obtain excellent protection over time. It dries to the touch in roughly 15 minutes and dries fully in roughly 24 hours. Application: metal and wood surface, plaster, doors, railings, gates, metal grates, metal cabinets, flashings, furniture, garden furniture. Sku:V400MIC
RAD: it s a special paint for the decoration and protection of all internal and external surfaces of heaters and radiators, resistant to 120 ' C. Suitable for home radiators, heat registers, electric convectors. PAST.2 it's an acrylic enamel for the decoration and protection of all surfaces of all appliances, as washing machines, dishwashers, refrigerators, etc. It dries to the touch in roughly 15 minutes and dries fully in roughly 24 hours. Sku:V400RAD/PAST.2
This primer is designed to be used as the strong base coat to ensure the perfect adhesion of all enamel spray on diffi cult surfaces such as metal alloys and metals. It protects metal surfaces from rust. Also suitable as a fi ller in bodywork car sector for small imperfections and scratches. Clean carefully the surface before application and shake vigorously the can. For overcoating are required at least 24/48 hours. After use, it's advisable to spray for 2/3 seconds with the can upside down to avoid the block of the nozzle. Sku:V400PRIMER
SHRUB COVER It's a formulate that gives high hiding power after just one coat to completely eliminate any stain at all by penetrating deep below the surface and then creating a seal for the prevention of new stains. Suitable for all stains caused by smoke on walls, mildew, and dirt in general. The STAIN COVER covers any stain when applied evenly over the area to be treated. The removal of particularly â??resistantâ?? stains may require repeated application of product always from a distance of 20-30 cm, paying attention to avoid runs. The product dries in 5-8 minutes if applied at a temperature of 20�°C. Sku:V500COPRI
Wood stain formulated for deep penetration and long lasting protection. Made for interiors and exteriors, it suitable for protection of wooden products such as fixtures, matchboards, boats, garden furniture, and more. It effectively protects the wood from aggressive atmospheric conditions such as sun and water. It guarantees easy maintenance, even after long periods of time from the original application. It can be painted over or left as clean sheen allowing the natural grains and knots of the wood to be more visible and accentuated. Sku:V407
This paint is designed to be used as the base coat for a fi nishing enamels. It provides a strong base to ensure the perfect adhesion of the enamel spray on difficult surfaces such as plastics and metals. It protects metal surfaces from rust. On cars it covers small imperfections and scratches. Clean carefully the surface before application and shake vigorously the can. It dries on touch in roughly 15 minutes and dries fully in roughly 22 hours. For overcoating are required at least 24/48 hours. After use, it;s advisable to spray for 2/3 seconds with the can upside down, to avoid the block of the nozzle. Sku:V400PAST