X100 Fully Automatic Pallet Wrapping Machine Fully Automatic Pallet Wrapping Machine Fully Automatic Pallet Wrapping Machine Product Application 1.Pallet stretch wrapping machine use LLDPE stretch film as the main packing material to wrap the bulk cargos stacked on the pallet 2.Film provides extra support during transportation and storage to protect them from dust, moisture or damage 3.The pallet wrapping machine has been widely used in industries such as glassware, tools, electric & electronic, paper, pottery, food & beverage, etc Main Features 1. High efficiency and low electricity-consumption, convenient in operation. 2. The wrapping type and times can be designed on customersrequirements. 3. Photoelectric sensor test pallet height automatic 4. Auto reset of turn tab le 5. Pre-stretch ratio: 300% 6. Programmable control and frequency converter is available. 7.PLC control ,manual optional. Wrap cycle (top, bottom, reinforcement) adjustment.Variable lift speed/ film tension control. Film up/down controls. 8.Pallet stretch wraping machine soft start and soft stop. 9.Suitable for heavy pallet 10.Remote control sytem ,fully automatic cut and clamp film
X300 Top Pressure Fully Automatic Pallet Wrapping Machine Horizontal Pallet Wrapper Fully Automatic Pallet Wrapping Machine 1.Motor Drive Top Plate, stable pressure on goods 2.Pallet stretch wrapping machine use LLDPE stretch film as the main packing material to wrap the bulk cargos stacked on the pallet 3.Film provides extra support during transportation and storage to protect them from dust, moisture or damage 4.The pallet wrap machine  has been widely used in industries such as glassware, tools, electric & electronic, paper, pottery, food & beverage, et. 1. High efficiency and low electricity-consumption, convenient in operation. 2. The wrapping type and times can be designed on customersâ?? requirements. 3. Photoelectric sensor test pallet height automatic 4. Auto reset of turn table 5. Pre-stretch ratio: 300% 6. Programmable control and frequency converter is available. 7.PLC control ,manual optional. Wrap cycle (top, bottom, reinforcement) adjustment.Variable lift speed/ film tension control. Film up/down controls. 8.Pallet wraping machine soft start and soft stop. 9.Suitable for light and unsteady  pallet 10.automatic cut and clamp film 11.Remote control start machine
X3 Type Pressure Standard Pallet Wrapping Machine Smart Pallet Wrapper Standard Pallet Wrapping Machine 1.Motor Drive Top Plate, stable pressure on goods 2.Pallet stretch wrapping machine use LLDPE stretch film as the main packing material to wrap the bulk cargos stacked on the pallet 3.Film provides extra support during transportation and storage to protect them from dust, moisture or damage 4.The pallet wrap machine has been widely used in industries such as glassware, tools, electric & electronic, paper, pottery, food & beverage, et. 1. High efficiency and low electricity-consumption, convenient in operation. 2. The wrapping type and times can be designed on customers requirements. 3. Photoelectric sensor test pallet height automatic 4. Auto reset of turn table 5. Pre-stretch ratio: 300% 6. Programmable control and frequency converter is available. 7.PLC control ,manual optional. Wrap cycle (top, bottom, reinforcement) adjustment.Variable lift speed/ film tension control. Film up/down controls. 8.Pallet wraping machine soft start and soft stop. 9.Suitable for light and unsteady pallet 10.automatic cut film
X5 Model Standard E Type Turntable Pallet Wrapping Machine Turntable Pallet Wrapper Standard Pallet Wrapping Machine Product Application 1Pallet wrap machine use LLDPE stretch film as the main packing material to wrap the bulk cargos stacked on the pallet 2.Film provides extra support during transportation and storage to protect them from dust, moisture or damage 3.The pallet wrap machine  has been widely used in industries such as glassware, tools, electric & electronic, paper, pottery, food & beverage, et. Main Features  1. High efficiency and low electricity-consumption, convenient in operation. 2. The wrapping type and times can be designed on customers requirements. 3. Photoelectric sensor test pallet height automatic 4. Auto reset of turn table 5. Pre-stretch ratio: 300 % 6. Programmable control and frequency converter is available. 7.PLC control ,manual optional. Wrap cycle (top, bottom, reinforcement) adjustment. Variable lift speed/ film tension control. Film up/down controls. 8.Pallet wraping machine soft start and soft stop. 9.Suitable for Light pallet 10.Automatic cut film function 11.E type turntable ,easy for pallet jack load the pallet on machine
Portable residential A/C oil less refrigerant recovery equipment recharge system CM2000 price Products in CM2000/2000A/3000A series refrigerant recovery machine are special for out maintenance. Stability of these small refrigerant recovery machine are with todays�??s world advanced level. Applications are as follows: small household A/C,automotive A/C, refrigerator production factories, on-site maintenance of small and medium HVAC/R equipments(portable refrigerant recovery machine ) Unique Advantages of CM2000 series refrigerant recovery machine - Long time running sustainably up to 24 hours - Oil free compressor - Maintenance free - Capable of handling all kinds of refrigerants - Automatic high pressure cut-off switch for Safety - The outer shell adopts one-off rotary technology with high intensity and concussion resistance. - Overall protection device, safe credibility - Meet ARI700 Standards - Automatic Low Pressure Shut-off - 2 years warranty - Weighs only 16.8KG
Product Description 1. Product name: WHP mixing tube 2. Condition: New 3.Material: tungsten carbide 4.Feedback Time: Within 12 hours Quality Assurance 1. Strict control on choose of the raw material sources. 2. Speciific technology guide for the production of each product. 3. Completed quality testing system for the semi-finished products and finised products. Our Service Pre-sales Service * Inquiry and consulting support. * Sample testing support. * View our Factory. After-sales Service * Answer product doubts and solve usage problems * Product quality problem, give replacement About Miaoke "Miaoke" was our trademark for serving China domestic market since we established in 2007. Until 2013 the year for our brand evolution, we started brand-new logo WHP �® as our trade mark for global marketing. Absolutely, we already own the trademark right in many countries. Packing & Delivery Packing Details : Water jet cutting machine normal spare part package : soft packing inside ,Miaoke standard carton packing outside. Water jet cutting machine/Waterjet intensifier pump package : Standard carton packing inside,wooden packing outside. Delivery Details : 1-3 days for the goods in stock We support shipping cargo by international express normally. The mode of transportation can be specified by the customer.
TXM-500 Horizontal Machining Center can process the bigger component and as well as the indexing rotation process.Most suitable for multifaceted machining about the component, include milling,drilling ,boring and tapping.  Technical Characteristics : Powerful cutting capability with excellent precision and performance makes drilling and milling easily;High speed ,super pprecision and more reliable structure ;High rigidity .super efficient,high torque and heavy cut features ;make full use of higher productive and precision processing. Super-high processing efficiency: TXM-500 Horizontal Machining Center fertures in high rigidity ,stable performance and high performance-cost ratio,which is the optimal choice for sourcing horizontal machining center .  T-type base structure ,high-rigidity and slide way support .gantry column.hiigh rigidity saddle base .strong spindle support. X/Y/Z feeding drive system :high-torque servo motor directly connected with Φ50 bal screw by coupling ;both ends of ball screw are fixed and pre-stretched .High transmission rigidity structure ensure the positioning precision . Spindle transmission system :servo motor direct ransmission to high-precision spindle ;higher transmission efficiency ,lower noise and vibration;continuous output power for higher processing efficiency;specially-designed spindle from Taiwan . Anti-collision design to prevent nut base ,motor base and bearing base from colliding with each other for protect the machine precision . One-piece Oil-coolant separation system ensures that polluted lubricant adn coolant flow back separately ,prevent the coolant from being polluted . Newly-designed and fully-sealed cover:safe and convenient .
M-Triangel CP-301Mini Efficient Purification Fume Instrument Soldering Cleaner Fume Extractor Air Cleaner, M-Triangel CP-301 Desktop Smoking Welding Purifier fume extractor with clear cover for laser machines 110V/220V. Features: Small and exquisite: Small size, easy to carry and store. Lifetime warranty: We provide lifetime warranty for you. Variety of styles: Multiple functions, can be used to cut paper tape, glazes, etc. Reliable to use: Easy to use, fast and reliable to clean. Energy saving: High temperature resistance, low noise during operation, energy saving, high efficiency and convenient use. Ease of use: A practical and effective combination of smokers that may help prevent the Top quality: Brand new and high quality. Sharp blade: Three times quick cutting, easier to replace the damaged filter head, high efficiency and energy saving. Stability: The kit uses a special process that provides increases job site durability and stability. Wood: Wood burning kit can be used for the production and lighting of home, office, building or the vertical drawstring. Description: M-Triangel CP-301 is a portable Mini smoke purifier, which is suitable for fume filtration during electronic repair and soldering, and also for fume filtration during laser cutting. Installation is simple and convenient, without the need for alternative pipes, is conducive to a clean and beautiful working space. Triple filter design to ensure that the filter out the harmful substances in the smoke, to protect human safety. The pre-filter, medium-efficiency filter, and main filter can be replaced individually, extending the life of the main filter. Built-in air circulation filter to avoid indoor air/heating exhaust to the outside world, the real meaning To save energy, at the same time meet the national environmental requirements. High-power DC brushless motor, air volume, long life. Low noise design, strong absorption, high rotating speed Extension-type station design, air volume adjustable, directional duct adjustment, positioning freely. Product Parameters: Body size: 153 153 76.5 mm Power: 15W Interface diameter: 6 cm Air volume: 1.5 m/min Net weight: 1.2KG Shipping weight: 4 kg Packing list: 1 x CP-301 Fume Extractor 1 x Fiber cotton 1 x Expansion tube 1 x Manual 1 x Transparent shield (optional)
Choice of several systems available Choice of ratchet systems Endless or two part versions Choice of 25mm - 75mm wide polyester webbing Anti-abrasion protection available Anti cutting protection available Conforms to B.S. 5759: 1987 Ratchet Reference, Minimum Breaking Strength, Rated Assembly Strength, Web Width (mm), Two Part (kg), Endless (kg), Two Part (kg), Endless (kg), KRL-25, 1200, 2400, 600, 1200, 25, KRL-35, 3000, 6000, 1500, 3000, 35, KRL-50, 5000, 10000, 2500, 5000, 50, KRL-75, 8000, 16000, 4000, 8000, 75, Cambuckle Reference, Minimum Breaking Strength, Rated Assembly Strength, Web Width (mm), Two Part (kg), Endless (kg), Two Part (kg), Endless (kg), KCB-25, 250, 500, 125, 250, 25, KCB-35, 1000, 2000, 500, 1000, 35, KCB-50, 1500, 3000, 750, 1500, 35 Features Zebra manufactures two basic types of lashing systems, which are each available in either two part or endless configurations, with a wide variety of different end terminals. Cambuckle Compact and light in weight, Cambuckle lashings are ideal for securing light loads, the tension being applied by pulling the lashing hand tight. The Lashing release mechanism operates by depressing the thumb bar. No pre-tensioning of the webbing is possible. Cambuckle lashings are available in a range of Minimum Break Strengths from 250 to 1000 kg. Ratchet Systems For medium to heavy duty applications, Zebra offers a very wide variety of Ratchet Lashings Systems in Minimum Break Strengths ranging from 500 to 8000 kg. 25mm, 35mm, 50mm and 75mm webbing widths are available depending upon the loading requirements of the selected Lashing system.Within the range are many different types of Ratchet systems, all carefully designed and engineered to exert the right amount of pre-tensioning to the lashing. How to order Lashings Having first selected the appropriate Minimum Breaking Strength, the lashing format must next be considered. Here, there are two options: Two-Part or Endless, with the possibility to specify the fixed and overall lengths of a Two Part Lashing or the overall length of an Endless Lashing. FL= Fixed Length OL= Overall Length Two Part
D6 steel is a high-carbon, high chromium tool steel alloyed with tungsten that is characterized by high compressive strength, high wear resistance, high surface hardness and good hardening stability. It is also called SKD2 steel and DIN 1.2436 steel. And D6 steel chemical composition and heat treatment information are below. Tool steels are primarily used to manufacture tools that can be used for machining metals, woods, and plastics. They are generally ingot-cast wrought products, and have the potential to be stable at elevated temperatures and withstand high specific loads. D6 Steel Application SKD2 steel chemical composition makes it become good tool steel in the industry. SKD2 steel is used for forming tools; molds for abrasive plastics and ceramics; long-run press tools; blanking and shearing tools for hard materials; stamping tools; scraping tools and etc. D6 Steel Round Bar Sheet Plate Heat Treatment Forging SKD2 tool steel is heated slowly and uniformly to 700�°C (1292�°F) and then more rapidly to 900-1050�°C (1652-1922�°F). Annealing SKD2 tool steel is then annealed at 800-840�°C (1472-1544�°F) and cooled. Hardness of the steel after annealing will be approximately 225 Brinell. Stress Relieving Stresses from SKD2 tool steel can be eliminated before hardening by heating up to 650-700�°C (1202-1292�°F), if machining operations have been heavy. The steel is then allowed to cool slowly. Hardening SKD2 steel is pre-heated slowly to 750-800�°C (1382-1472�°F) and thoroughly soaked. Heating is then continued till the final hardening of 950-980�°C (1742-1796�°F), followed by air or oil quenching. Tempering The SKD2 steel is heated uniformly and thoroughly at the selected tempering temperature. Double tempering can also be carried out with intermediate cooling to room temperature. Notice We have our own cutting and processing equipment. Specifications can be cut and customized according to your requirements. We are a professional special steel stockist and supplier with a high-quality stand for many years. Please contact us for any request of D6/SKD2 steels materials. Songshun Steel always with you.
Product Description 1. Product name: WHP Sapphire nozzle 2. Condition: New 3.Material: Sapphire Crystal 4.Feedback Time: Within 12 hours Quality Assurance 1. Strict control on choose of the raw material sources. 2. Speciific technology guide for the production of each product. 3. Completed quality testing system for the semi-finished products and finised products. Our Service Pre-sales Service * Inquiry and consulting support. * Sample testing support. * View our Factory. After-sales Service * Answer product doubts and solve usage problems * Product quality problem, give replacement About Miaoke "Miaoke" was our trademark for serving China domestic market since we established in 2007. Until 2013 the year for our brand evolution, we started brand-new logo WHP ® as our trade mark for global marketing. Absolutely, we already own the trademark right in many countries. Packing & Delivery Packing Details : Water jet cutting machine normal spare part package : soft packing inside ,Miaoke standard carton packing outside. Water jet cutting machine/Waterjet intensifier pump package : Standard carton packing inside,wooden packing outside. Delivery Details : 1-3 days for the goods in stock We support shipping cargo by international express normally. The mode of transportation can be specified by the customer. FAQ Q: Do you have the products I want? A: We have the most complete waterjet machine parts. We have a professional technical team, which can provide customized services.Please feel free to contact us if you have any needs. Q: Are you trading company or manufacturer ? A: We are a company integrating industry and trade. Q: How long can I get my waterjet parts? A: We can arrange shipment with 24 hours if products in stock. Q: What is your terms of payment ? A: Payment=1000USD, 30% T/T in advance ,balance before shippment. Q: How long is my warranty? A: The waterjet spare parts without warranty, except waterjet high pressure cylinder, waterjet accumulator, waterjet intensifier.
Although the wide use of chicken wire mesh in chicken protection, chicken wire mesh is no longer just for chicken anymore. The distinctive feature of chicken wire mesh is its hexagons. And benefited from its light weight, it is found gradually that chicken wire mesh might also apply wonderfully to various garden applications. Chicken Wire Garden Fence Garden fence is commonly used to screen out the unwanted animals and pets like rabbits, rat, deer, neighbor dogs or cats out in a friendly way. Compared with welded wire fence and expanded metal fence, chicken wire mesh is lighter, inexpensive. Compared with chain-link fence, chicken wire mesh is not easy to unravel. Therefor chicken wire is an better option for medium security needed places. Nevertheless, the selection of type and specification of garden fence is determined by your garden circumstances and intruder you want to deter. Galvanized chicken wire mesh used for surrounding garden has usually 1 inch opening between two 20 gauge twisted wires. Stretching wires are added every 50 cm to increase the structure stability of the hexagonal wire mesh and then protect your plants. As for its selvedge wires, we take one or two threads of greater diameter than that used for the net. Before putting the chicken wire fence up, a trench should be created for the underground chicken wire installation. With the help of this underground chicken wire, no bunnies can dig holes through the vertical fence and get into the interior of your garden in secret. Or we could directly putting chicken wire on the surface of earth to create an illusion of intimidation. A small fence is made to protect three boxes of plants. GUCWM-01: Rolls of chicken wire mesh could be cut into small panels and then be nailed into planks individually.Chicken wire mesh with vegetables inside and flowers outside. GUCWM-02: Chicken wire mesh could be used without being cut and then fixed into wooden posts as a whole. A chicken wire mesh is fixed on the wooden frame and a trench is created for deterring gophers. GUCWM-03: The bottom of the chicken wire mesh is placed in a pre-dredged trench to prevent rabbits and gophers.Chicken wire mesh is spread on the earth and planks is linked together above the chicken wire.
Hole Openers can be quoted with new/unused surplus or used Steel Tooth or TCI Cutters Hole Openers. At some point it may be necessary to increase the size of a pre-drilled hole to a larger diameter or to drill large diameter holes. Hole opener bits are designed specifically for this purpose. Bits are custom manufactured in a wide range of styles to meet field requirements. A custom hole opener is an effective way of enlarging holes, hence the name "Hole Opener". The Hole Opener Advantage Straighter Holes - By drilling a smaller hole with a "pilot" bit, then attaching that said bit onto the bottom of the the hole opener. The hole opener will follow the path of the hole drilled by the smaller bit. Larger Holes with Smaller Rigs - By drilling a hole in stages, larger holes can be drilled with smaller rigs. A smaller hole requires less power. Replacing Cutters and Cutting Cost - On most Hole Opener designs, the cutters can be easily replaced. The cost to replace a cutter is a fraction of the cost to replace a large tricone rock bit. Cost of Large Rock Bits - Larger diameter rock bits not only cost a lot, they can be difficult to find. A more economic solution is to use a hole opener that uses smaller tricone rock bit segments.. Flexability - Hole Openers can be fabricated in just about any size, and can be configured to drill through any formation. Operational Considerations Drilling Weight - The choice of drilling weight is determined based on the recommendations of the bit manufacturer and the number of cutters on the hole opener. Number of Cutters - The number of cutters placed on a hole opener is governed by the following facts: 1.Maximum number which will fit around the perimeter. 2.The greater the number of cutters, the less the weight, which therefore reduces the penetration rate. 3.In softer formations, less weight is needed to penetrate. 4.The greater the number of cutters, the smoother the tool will run. 5.The greater the number of cutters, the greater the cost. 6.The greater the number of cutters, the longer the cutters will last Rotary Speed - Maximum speed is determined by the manufacturer's recommendation and the calculation to account for the linear distance the cutter is moving per revolution. Hole Cleaning - A frequently over looked point of hole opener operation is hole cleaning. The volume of cuttings to remove from a hole increase by a squared factor with an increase in hole diameter.
Choline Chloride-75% Aq Choline Chloride in Clay Stabilization for the Oil and Natural Gas Industry Choline chloride 75% is a chemical compound which is used into various industrial applications, predominately as a component for hydraulic fracturing of shale natural gas wells. Choline Chloride in Clay Stabilization for the Oil and Natural Gas Industry Drilling and stimulation in shale and other clay containing formations pose challenges due to day swelling. This swelling causes a number of issues including: -Wellbore instability -Cuttings disintegration Br balling Fines migration -Reductions in permeability of the formation to hydrocarbons Choline Chloride has proven itself as a safe and very effective clay stabilizer, at a reasonable cost functions through ion exchange, where choline chlonde provides a cation to replace the native solubilized clay cation (typically sodium) Choline Chloride is used as a shale swelling inhibitor in drilling fluid, completion fluid, and workover fuit, to prevent shale from expansion and hydration, providing wellbore stability. These issues can result in higher drilling costs and slower production rates. Clay stabilizers reduce day swelling and its associated risks leading to lower drilling costs and improved production rates Potassium chloride (KCL) is commonly used in preventing the swelling of clay as a temporary clay stablizer However, the use of KCL in drilling carries environmental concerns as chlorides do not degrade and can enter surface water carrying heavy metal including cadmium and mercury The key features offered by Choline salts as an alternative to traditional clay stabilizers include Biodegradability and reduction in the amount of chlorides Superior performance and use at much lower levels Compatibility with brine, calcium chloride and KCL solutions Ability to work well with known fracturing fluids, cross-linkers and breakers Minimization in chemical handling including pre-mixing and saltwater disposal Flexibility for use in all environments
We are manufacturer & exporter of Brass Neutral Links. They are designed with the intention of minimising issues during installation. The screws minimize the risk of shearing, stripping and cross threading which each hole is clearly identified with an engraved number. Brass Neutral Links are available in various configurations. Brass Neutral Links and Bars are used for ground or earth in mains electrical wiring system which provides a low impedance path to the earth to prevent hazardous voltages from appearing on equipment. Terminal Blocks are all developed exclusively as per Customers design & specification. Material : Free Cutting Brass, High Tensile Brass, CDA 360 Brass, Alloy 360 Brass, CDA 230 Brass. Size : Begins from M2 or equivalent threads, 2 ways to 50 ways. Length : 1 meter to 15 meter or as per customers requirement. Suitability : 70Amp, 90A, 110A, 165A through 350Amp Screws : Steel Multi-Head, Zinc plated - Headless set screw, Headed slotted machine screw, Headed machine screw combination & square slot, Headless Hex socket, etc. Finish : Natural, Nickel Plated, Tin Plated, Chrome Plated, Electrolyte Tin Plated or any coating as per customer specification. Features : Lighter and easier to handle. The use of modern polymer channel has reduced the weight of the products making them easier to handle. Pre-Drilled fixing holes for ease of installation. Plastic channel base is entirely corrosion proof. High Durability, Tensile strength and Resistant to adverse conditions. Additional Information: Production Capacity: 100000 Pieces per month Delivery Time: Depends upon order volume Packaging Details: Sea worthy export packaging : Wooden Pallet > Paper Box > Plastic Bag
We are manufacturer & exporter of Brass Neutral Links. They are designed with the intention of minimising issues during installation. The screws minimize the risk of shearing, stripping and cross threading which each hole is clearly identified with an engraved number. Brass Neutral Links are available in various configurations. Brass Neutral Links and Bars are used for ground or earth in mains electrical wiring system which provides a low impedance path to the earth to prevent hazardous voltages from appearing on equipment. Terminal Blocks are all developed exclusively as per Customers design & specification. Application : Used in Street Light Isolator, Distribution Board, Switchgear, Electrical Panels Boards, Electrical and Telecommunication, Circuit breaker, RCD, etc. In MCBs ELCBs and Isolators to protect the installation For termination of neutral and ground wires on bus bar For termination of Rated Conductors For mounting of DIN Rails and clamp type For surface mount applications Designed for Easy Installation and Termination Carries current back to the source Material : Free Cutting Brass, High Tensile Brass, CDA 360 Brass, Alloy 360 Brass, CDA 230 Brass. Size : Begins from M2 or equivalent threads, 2 ways to 50 ways. Length : 1 meter to 15 meter or as per customers requirement. Suitability : 70Amp, 90A, 110A, 165A through 350Amp Screws : Steel Multi-Head, Zinc plated - Headless set screw, Headed slotted machine screw, Headed machine screw combination & square slot, Headless Hex socket, etc. Finish : Natural, Nickel Plated, Tin Plated, Chrome Plated, Electrolyte Tin Plated or any coating as per customer specification. Features : Lighter and easier to handle. The use of modern polymer channel has reduced the weight of the products making them easier to handle. Pre-Drilled fixing holes for ease of installation. Plastic channel base is entirely corrosion proof. High Durability, Tensile strength and Resistant to adverse conditions.
We are manufacturer & exporter of Brass Neutral Links. They are designed with the intention of minimising issues during installation. The screws minimize the risk of shearing, stripping and cross threading which each hole is clearly identified with an engraved number. Brass Neutral Links are available in various configurations. Brass Neutral Links and Bars are used for ground or earth in mains electrical wiring system which provides a low impedance path to the earth to prevent hazardous voltages from appearing on equipment. Terminal Blocks are all developed exclusively as per Customers design & specification. Application : Used in Street Light Isolator, Distribution Board, Switchgear, Electrical Panels Boards, Electrical and Telecommunication, Circuit breaker, RCD, etc. In MCBs ELCBs and Isolators to protect the installation For termination of neutral and ground wires on bus bar For termination of Rated Conductors For mounting of DIN Rails and clamp type For surface mount applications Designed for Easy Installation and Termination Carries current back to the source Material : Free Cutting Brass, High Tensile Brass, CDA 360 Brass, Alloy 360 Brass, CDA 230 Brass. Size : Begins from M2 or equivalent threads, 2 ways to 50 ways. Length : 1 meter to 15 meter or as per customers requirement. Suitability : 70Amp, 90A, 110A, 165A through 350Amp Screws : Steel Multi-Head, Zinc plated - Headless set screw, Headed slotted machine screw, Headed machine screw combination & square slot, Headless Hex socket, etc. Finish : Natural, Nickel Plated, Tin Plated, Chrome Plated, Electrolyte Tin Plated or any coating as per customer specification. Features : Lighter and easier to handle. The use of modern polymer channel has reduced the weight of the products making them easier to handle. Pre-Drilled fixing holes for ease of installation. Plastic channel base is entirely corrosion proof. High Durability, Tensile strength and Resistant to adverse conditions.
We are manufacturer & exporter of Brass Neutral Links. They are designed with the intention of minimising issues during installation. The screws minimize the risk of shearing, stripping and cross threading which each hole is clearly identified with an engraved number. Brass Neutral Links are available in various configurations. Brass Neutral Links and Bars are used for ground or earth in mains electrical wiring system which provides a low impedance path to the earth to prevent hazardous voltages from appearing on equipment. Terminal Blocks are all developed exclusively as per Customers design & specification. Application : Used in Street Light Isolator, Distribution Board, Switchgear, Electrical Panels Boards, Electrical and Telecommunication, Circuit breaker, RCD, etc. In MCBs ELCBs and Isolators to protect the installation For termination of neutral and ground wires on bus bar For termination of Rated Conductors For mounting of DIN Rails and clamp type For surface mount applications Designed for Easy Installation and Termination Carries current back to the source Material : Free Cutting Brass, High Tensile Brass, CDA 360 Brass, Alloy 360 Brass, CDA 230 Brass. Size : Begins from M2 or equivalent threads, 2 ways to 50 ways. Length : 1 meter to 15 meter or as per customers requirement. Suitability : 70Amp, 90A, 110A, 165A through 350Amp Screws : Steel Multi-Head, Zinc plated - Headless set screw, Headed slotted machine screw, Headed machine screw combination & square slot, Headless Hex socket, etc. Finish : Natural, Nickel Plated, Tin Plated, Chrome Plated, Electrolyte Tin Plated or any coating as per customer specification. Features : Lighter and easier to handle. The use of modern polymer channel has reduced the weight of the products making them easier to handle. Pre-Drilled fixing holes for ease of installation. Plastic channel base is entirely corrosion proof. High Durability, Tensile strength and Resistant to adverse conditions.
We are manufacturer & exporter of Brass Neutral Links. They are designed with the intention of minimising issues during installation. The screws minimize the risk of shearing, stripping and cross threading which each hole is clearly identified with an engraved number. Brass Neutral Links are available in various configurations. Brass Neutral Links and Bars are used for ground or earth in mains electrical wiring system which provides a low impedance path to the earth to prevent hazardous voltages from appearing on equipment. Terminal Blocks are all developed exclusively as per Customers design & specification. Application : Used in Street Light Isolator, Distribution Board, Switchgear, Electrical Panels Boards, Electrical and Telecommunication, Circuit breaker, RCD, etc. In MCBs ELCBs and Isolators to protect the installation For termination of neutral and ground wires on bus bar For termination of Rated Conductors For mounting of DIN Rails and clamp type For surface mount applications Designed for Easy Installation and Termination Carries current back to the source Material : Free Cutting Brass, High Tensile Brass, CDA 360 Brass, Alloy 360 Brass, CDA 230 Brass. Size : Begins from M2 or equivalent threads, 2 ways to 50 ways. Length : 1 meter to 15 meter or as per customers requirement. Suitability : 70Amp, 90A, 110A, 165A through 350Amp Screws : Steel Multi-Head, Zinc plated - Headless set screw, Headed slotted machine screw, Headed machine screw combination & square slot, Headless Hex socket, etc. Finish : Natural, Nickel Plated, Tin Plated, Chrome Plated, Electrolyte Tin Plated or any coating as per customer specification. Features : Lighter and easier to handle. The use of modern polymer channel has reduced the weight of the products making them easier to handle. Pre-Drilled fixing holes for ease of installation. Plastic channel base is entirely corrosion proof. High Durability, Tensile strength and Resistant to adverse conditions.
We are manufacturer & exporter of Brass Neutral Links. They are designed with the intention of minimising issues during installation. The screws minimize the risk of shearing, stripping and cross threading which each hole is clearly identified with an engraved number. Brass Neutral Links are available in various configurations. Brass Neutral Links and Bars are used for ground or earth in mains electrical wiring system which provides a low impedance path to the earth to prevent hazardous voltages from appearing on equipment. Terminal Blocks are all developed exclusively as per Customers design & specification. Application : Used in Street Light Isolator, Distribution Board, Switchgear, Electrical Panels Boards, Electrical and Telecommunication, Circuit breaker, RCD, etc. In MCBs ELCBs and Isolators to protect the installation For termination of neutral and ground wires on bus bar For termination of Rated Conductors For mounting of DIN Rails and clamp type For surface mount applications Designed for Easy Installation and Termination Carries current back to the source Material : Free Cutting Brass, High Tensile Brass, CDA 360 Brass, Alloy 360 Brass, CDA 230 Brass. Size : Begins from M2 or equivalent threads, 2 ways to 50 ways. Length : 1 meter to 15 meter or as per customers requirement. Suitability : 70Amp, 90A, 110A, 165A through 350Amp Screws : Steel Multi-Head, Zinc plated - Headless set screw, Headed slotted machine screw, Headed machine screw combination & square slot, Headless Hex socket, etc. Finish : Natural, Nickel Plated, Tin Plated, Chrome Plated, Electrolyte Tin Plated or any coating as per customer specification. Features : Lighter and easier to handle. The use of modern polymer channel has reduced the weight of the products making them easier to handle. Pre-Drilled fixing holes for ease of installation. Plastic channel base is entirely corrosion proof. High Durability, Tensile strength and Resistant to adverse conditions.
