Diesel is a light petroleum product, a complex mixture of hydrocarbons (with a carbon atom number of about 10-22), used as fuel for diesel engines. It is mainly composed of diesel fractions produced through processes such as crude oil distillation, catalytic cracking, thermal cracking, hydrocracking, and petroleum coking. It can also be produced through shale oil processing and coal liquefaction, and can be divided into two categories: light diesel (with a boiling point range of about 180-370 â??) and heavy diesel (with a boiling point range of about 350-410 â??). Widely used in large vehicles, railway locomotives, and ships. The most important use of diesel is for diesel engines in vehicles and ships. Compared with gasoline engines, diesel engines have higher thermal efficiency and lower fuel consumption. Diesel has low energy consumption, so some small cars and even high-performance cars have switched to diesel.
Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS
PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS.
Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS
PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS.
Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS
Diesel fuel is generally a liquid fuel used in diesel engines, which ignites the fuel without sparking by compressing the inlet air mixture and then injecting the fuel. (Glow plugs, grid heaters, and block heaters help achieve high combustion temperatures during cold weather starting.) The most common type of diesel fuel is specific fractional distillation of fuel oil, but alternatives that are not derived from oil, such as biodiesel, biomass to liquid (BTL) or gas to liquid (GTL) diesel, are increasingly being developed and adopted. To distinguish these types, in some academic circles, petroleum-derived diesel fuel is increasingly referred to as oil-oil. Ultra Low Sulfur Diesel (ULSD) is the standard for determining substantially reduced sulfur diesel.
Diesel fuel is generally a liquid fuel used in diesel engines, which ignites the fuel without sparking by compressing the inlet air mixture and then injecting the fuel. (Glow plugs, grid heaters, and block heaters help achieve high combustion temperatures during cold weather starting.) The most common type of diesel fuel is specific fractional distillation of fuel oil, but alternatives that are not derived from oil, such as biodiesel, biomass to liquid (BTL) or gas to liquid (GTL) diesel, are increasingly being developed and adopted. To distinguish these types, in some academic circles, petroleum-derived diesel fuel is increasingly referred to as oil-oil. Ultra Low Sulfur Diesel (ULSD) is the standard for determining substantially reduced sulfur diesel.
Fishing boat, business boat, passenger boat, cabin boat, fiberglass boat, FRP boat, yacht, fish speed boat, leisure boat, rowing boat, power boat. Name : Specification Boat Materials : Fiberglass Boat size: 9.8m*2.81m*1.26m Max people : 11+1 Engine : outboard :115 x 2 Waterline : 0.45m above speed : 50km/h
1. d2 gas oil: one of the most widely traded petroleum products, it is commonly used in diesel engines. 2. en590: a high quality diesel fuel that meets european standards for emission control. 3. gasoline: a versatile fuel used in automobiles, motorcycles, and small engines. 4. lpg: liquefied petroleum gas, commonly used for heating, cooking, and as a fuel in vehicles. 5. lng: liquefied natural gas, a cleaner alternative to traditional fossil fuels, primarily used in power generation and transportation. 6. jp54: jet fuel used in aviation, meeting stringent quality standards and regulations. 7. jeta1: a type of aviation turbine fuel with specific characteristics suitable for use in low temperature conditions. 8. espo: east siberian pacific ocean blend, a high quality crude oil grade originating from russia. 9. lco etc: light cycle oil, used in various industries as feedstock or fuel..Trading, shipping , logistics services, import and export
Automobile diesel fuel (EN 590) Grade E (winter), recommended for use at ambient temperatures up to minus 15 C (limiting filterability temperature). Diesel fuel EN 590 (EN 590) Grade E is obtained from petroleum refined products and is intended for use as automotive fuel for diesel engines of cars and trucks. Diesel fuel meets the requirements of the international standard EN 590/2000 and is characterized by a low content of sulfur, aromatic hydrocarbons and a high cetane number, which leads to an overall reduction in sulfur oxide emissions, a decrease in the amount of particulate matter in exhaust gases and the formation of deposits in the fuel system of cars and heavy vehicles, reducing exhaust smoke and is the key to good starting properties of the fuel during cold start of the engine. The oil refining industry produces diesel fuel in accordance with GOST 305-82 of three grades: L - summer, used at ambient temperatures above 0 C; 3 - winter, used at temperatures up to -20 C (in this case, winter diesel fuel should have a stagnation
D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400 Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil. The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol. D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.
Our commitment to blending / packing of lubricants and greases as per iso standards. All our products are blended at iso certified plants, at whichever location the products may be blended. Product range 1- petrol engine oils 2- tractor fluids 3- transmission fluids 4- marine engine oils 5- industrial fluids 6- diesel engine oils 7- coolant & anti freeze 8- brake fluids Packaging - ctn 12x1 l - ctn 4x4l - ctn 4x5l - pali 20l - drum 208l - iso tanks or flexi tanks Private labeling available Manufactured at iso certified plants Meet & exceed various api certifications Oem approvals Please don't hesitate to contact us.
Used Engines HS Code 840820 PRICE = US$1,800/PIECE CIF ORIGIN: THAILAND PACKAGE: TONS MIN ORDER:5 PIECES DESCRIPTION There are several types of engines used in automobiles. The car engine types are generally described based on two factors: the fuel type and engine layout/number of cylinders (cylinder configuration. One of the most common types of engines is petrol and diesel engines. But that's a generic way to describe a car engine. SPECIFICATION General Engine Specifications Basic Engine Specifications I-6, 4-Stroke-Cycle-Diesel Displacement .......................................................................... 12.88 L (in3) Rated engine speed .................................................................... 2300 rpm High idle speed ........................................................................... 2530 rpm Low idle speed (programmable) ................................................... 550 rpm Peak torque ......................................................... 3,355 N m @ 1200 rpm Bore ....................................................................................... 135 mm (in) Stroke ...................................................................................... 150 mm (in) Aspiration .................................. Supercharged-Turbocharged-Aftercooled Governor ............................................................................................. ECU Fuel system type .................................................................. Common Rail Length ........................................................................... 1960 mm (77.1 in) Length to flywheel housing ........................................... 1476 mm (58.1 in) Width ............................................................................. 1195 mm (47.0 in) Height ............................................................................ 1117 mm (43.9 in) Weight, net dry (approx.) ................................................1672 kg (3686 lb) Rotation (from flywheel end) .......................................... Counterclockwise Flywheel housing/flywheel .................................................... SAE No. 01M Flywheel teeth ....................................................................................... 155 Tolerances Power ............................................................................................... +/- 3% Exhaust Stack Temperature ............................................................ +/- 8% Inlet Air Flow .................................................................................... +/- 5% Intake Manifold Pressure ............................................................... +/- 10% Exhaust Flow ................................................................................... +/- 6% Specific Fuel Consumption .............................................................. +/- 3% Heat Rejection ................................
"Diesel D6 virgin oil" is not a standard term in the oil industry. However, based on common industry terminology and understanding, it seems you might be referring to a specific type of diesel fuel. Here's a general description that could apply: Diesel D6 is typically classified under the category of middle distillates, which are refined products derived from crude oil. It is a specific grade of diesel fuel used primarily for automotive engines and industrial applications. The term "virgin oil" is not commonly used in this context; instead, "virgin" could imply that the diesel fuel is of high quality and meets certain specifications without being mixed or blended with lower-grade fuels. Key characteristics of Diesel D6 may include: High Energy Density: Diesel D6 is known for its high energy content per volume, making it efficient for use in diesel engines which are common in transportation (e.g., trucks, buses, trains) and industrial machinery. Low Sulfur Content: Modern regulations often require diesel fuels like D6 to have low sulfur content to reduce emissions and comply with environmental standards. Suitable for Various Climates: It is formulated to perform well in a range of temperatures and conditions, ensuring reliable operation in both cold and warm climates. Industrial and Automotive Use: Besides transportation, Diesel D6 is used in various industrial applications where a reliable and efficient fuel source is needed. For oil exporters, Diesel D6 represents a valuable product that can be sold to domestic and international markets where there is demand for high-quality diesel fuel. Exporting Diesel D6 requires compliance with international standards and specifications to ensure it meets the requirements of customers and regulatory authorities in the receiving countries. Origin: Kazakhstan / Russia.
Product Details: Storage : Dry Place Form : Liquid Grade : Industrial Grade Application : Industrial Supply Ability : 2500000 Kilograms Per Month Price And Quantity Minimum Order Quantity : 50 Kilograms Product Specifications Grade Industrial Grade : Application Industrial : Form Liquid Storage : Dry Place Trade Information Payment Terms : Cash in Advance (CID) Supply Ability : 2500000 Kilograms Per Month Delivery Time : 1 Week Main Domestic : Market All India Product Description We are offering D2 Diesel Oil that is distilled from crude oil. It can be used without reformers and additives. The first invented engines used this fuel before the petrol cars were invented. Nowadays this is used for diesel engine vehicles mostly in trucks, buses, boats, construction engines, agricultural vehicles and so on. Some small cars, boats and small trucks also have diesel engines that use this fuel. D2 Diesel Oil is an industrial grade liquid that is to be stored at a dry place to store for longer period of time.
Diesel generator, forklift, tower lights, scissor lifts, used construction equipment, spare parts, used engine, used equipment, spare parts, new equipment, komatsu, cat, perkins, cummins, all after market parts, used engine, new engine, refurbished equipments.
Ultra-Clean Diesel EN590 10PPM - Engineered for Environmental Excellence! Experience the future of diesel with our EN590 10PPM, a premium fuel designed with low sulfur content to minimize emissions and protect the environment. Ideal for modern engines, it enhances performance while significantly reducing your carbon footprint. Drive clean, drive smart. Diesel EN590 Ghost - The Invisible Shield for Your Engine! Our Diesel EN590 Ghost variant stands as a testament to innovation, offering superior protection and efficiency for your engine. With advanced formulation to combat wear and tear, it ensures your engine runs smoother, longer. Embrace the ghostly power that keeps you moving forward.
Gasoil, diesel, mazut, lpg, lng, jet fuel, bitumen, urea, used engine oil, occ, plastic waste, agrifood.Trade