Wheels For Robotics Used In Robowar Wheels Specially For RC Cars High Quality Genuine Products Material: ABS Plastic And Rubber
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
1.Blue elastic rubber wheel industrial caster wheel 2.Tread:elastic rubber 3.Hub:nylon 4.Roller bearing 5.Stainless steel ok Art no. Pcs/ctn capacity(kg) wheel size(d*w) 052075 60 50 75*26 052085 60 55 85*32 052100 38 70 100*34 052125 28 100 125*36 052160 12 150 160*39 Company Infromation Qingdao Pingyang International Trading Co., Ltd., was established in 2014,a famous and professional blue elastic rubber casters supplier. we are located in Qingdao, north of China. Our factory near the Qingdao Liuting International Air Port and Huangdao Sea Port,the traffic is very convenient. Which specializes in Industrial Casters. Bead Roller Machine . Hand Trolley. Corner Guards . Wire Springs . If you want to get high quality blue elastic rubber caster, please visit Qingdao Pingyang International Trading Co., Ltd. Packing&Shipping each caster put in a transparent bag, than put into a carton. 3" caster fixed and swivel: 50pcs/ctn, 4" fixed or swivel caster: 40pcs/ctn; 5" fixed or swivel casters: 30 pcs/ctn. 3" caster with brake: 40 pcs/ctn. 4" caster wieh brake: 30 pcs/ctn. 5" caster with brake: 25 pcs/ctn. Contact Us If you want to get more information about Qingdao Pingyang or blue elastic rubber caster,please feel free to contact us as follows.we will feedback to you within 24 hours.
Hole 4 5 8 10 Diameter 18" 19" 15" 16" 17" PCD: 120mm, 108mm, 112mm, 100mm, 114.3mm ET: 20mm, 30mm, 35mm, 25mm Warranty: 3 years Material: Aluminium alloy Finishing: Gloss Black with Machine Face Width: 6.5/7/7.5/8.0/8.5 Design: Multi Spoke Model Number: REW027 Product Name: Alloy Wheels Size: 15 16 17 18 19inch Color: any colour available Type: casting alloy wheels
- Standard grip ring stem 7/16" fits HM, Hon, Knoll, DX Racer, Razer and countless other brands (except IKEA); - Utility Patent No.10,434,820; - Rollerblade Polyurethane wheel - safest material for your floor; - No Chair Mat!; - ABEC-9 bearing for quiet smooth rolling; - Steel body withstands up to 660 lbs; - Roller color according to your request; LA warehouse pick up:
6" swivel heavy duty caster wheel with total brake,Top Plate Fitting.
Type furniture caster Place of origin guangdong, china (mainland) Brand name tianfu Model number ec-a-75-idb Type industrial caster Color black / others Diameter 75-200mm Load capacity 50-250kg Material rubber Brake swivel / fixed Bearing roller bearing Carton
China Big Factory Mute Caster Black Color Industrial Stem Heavy Duty adjustable Caster caster wheels Model Number 1B Width 75mm/100mm/125mm Warranty 1 years Material PVC Certification EPA Style Swivel & Rigid Customized support OEM Place of Origin China Product name caster Application Industry Color red Delivery Time 7 Days
ROLL CONTAINER 1. Model No.:RC1011N(Z base, without intermediate plate) 2. HS code:871680000 3. Size:L760*W830*H1535mm 4. Castor wheel:2pcs 5'' Nylon swivel+2pcs 5'' Nylon fixed 5. Max capacity:300kg 6. Surface treatment:Galvanized 7. Packing:Wrapping film 8. Net Weight:42KG 9. Bottom plate:Plastic 10. Payment terms:T/T 11.Application:Industry, mass retail, recycling, laundry, food and beverage, warehouse storage, wine-producing, PET preform, automobile part and tyre/tire industry
Industrial casters are mainly used in factories, mechanical equipment or transportation equipment, etc. We choose single wheels made of high-grade imported reinforced nylon (PA6), super polyurethane and rubber. The overall product has high impact resistance and strength. The metal parts of the bracket are made of high-quality steel plates and treated with galvanized or chrome-plated anti-corrosion treatment, and precision ball bearings are installed inside by means of integral injection molding. Customers can choose 3mm, 4mm, 5mm and 6mm steel plates as caster brackets.
name:furniture caster pin type wheel size:1.5''2.0''2.5''3.0'' type:pin type,fitting bolt,plate material:pp pvc nylon moq:500pcs
size:2inch material plastic type:top plate,bolt type,pin type color:black,white and black moq:200pcs delivery time:7days
Pu Industrial Cart Caster Wheel
wheel dia.:75mm, mount type: plate swivel wheel material:tpr
Grey Iron Casting Swivel Caster Wheels Heavy Duty / Semi Steel Cast Iron Caster Wheels Description Product Name: Cast Iron Caster Wheel, Swivel Caster wheel, Gray Iron Trundle,Transformer Casting Parts Material Grades: Gray Cast Iron, Grey Iron, Cast Iron ISO185 GRADE 100, 150, 200, 250, 300 USA ASTM A48 CLASS NO.20, NO.25, NO.30, NO.35, NO.40, NO.45 GERMANY DIN1691 GG10, GG15, GG20, GG25, GG30 EURO EN1561 EN-GJL-100, EN-GJL-150, EN-GJL-200, EN-GJL-250, EN-GJL-300 UK BS1452 100, 150, 180, 200, 220, 250, 260. 300 AUSTRALIA AS1830 T150, T180, T200, T220, T250, T260, T300 CHINA GB HT100, HT150, HT200, HT250, HT300 Application The caster wheel is used for transformer device. A caster is a wheeled device typically mounted to a larger object that enables relatively easy rolling movement of the object. Factory Information Our products are widely used for heavy duty and super-heavy industry, transportation, scaffolding, furniture. We can provide casters and wheels for nearly every mobility purpose, as we have many different types of high quality caster. Our products are 100% for exporting, mainly to Europe, USA and Japan. Please feel free to contact us for further information. Specification Wheel Size Wheel Width L.Capacity Setting Height Plate Size Spacing Hole 100mm 50mm 320kgs 142mm 102*115mm 85*72mm 125mm 50mm 370kgs 164mm 102*115mm 85*72mm 150mm 50mm 480kgs 190mm 102*115mm 85*72mm 200mm 50mm 520kgs 240mm 102*115mm 85*72mm Grey Iron Casting Swivel Caster Wheels Heavy Duty / Semi Steel Cast Iron Caster Wheels Our Advantages 1. Free charge & fast action for samples. 2. OEM & ODM acceptable. 3. Short lead time. 4. LOGO on products are acceptable. 5. Advanced machinery and equipments. 6. Strict quality control system. 7. Package could be adjusted. 8. Quick and effective reply by salesmen. Tag: gray cast iron castings, gray iron casting process
Many types and sizes are available Cartons size: 355*355*205mm
