Alloy And Crc Suppliers and Manufacturers

We are glad to propose 500 MT of stain less steel mill scale. Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products. At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel. The recovery ratio after melting in furnace for the most valuable alloy elements is: - Ni: 3.5 - 4.5% - Cr: 6-8% From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows: Waste code: 10 02 10 The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers. Chemical analysis of the material is available on request.

65Mn CK67 high carbon cold rolled spring steel strip Hardened and Tempered Steel Strip Hardened and Tempered is a thermal process that strengthens steel strips through a controlled heating and cooling process. The hardening process involves heating the steel strip to above the rapidly cooling. The steel strip in this condition is extremely brittle and requires further treatment in the tempering. Then strips are reheated to a lower temperature and holding it at the given temperature for a given period of time. This process is done in an inert atmosphere to avoid oxidation. This type of steel strip has big degree of toughness and has excellent spring properties Standard AISI, ASTM, BS, DIN, GB, JIS Place of Origin China Material Hot Rolled Surface Polished Application shutter door, plastic trowel, bricklayer trowel, putty knives, scraper, springs, metal part, shoe insole, shoe accessories, blade, band saw blade Brand Name HENSON Width 2.0mm-300.0mm Length Customize Tolerance +/-10% Hardness 40-55HRC Surface nature, blue, yellow, white, polish Edge Slit,Round,Square MOQ 1000KGS Tolerance thickness+/-0.01mm max,width +/-0.05mm max Type strip,coil,sheet Coil ID 300-500 mm Tensile Strength 540-1575N/mm2 Yield Strength 370-1475N/mm2

High purity Pure Copper Foil / strip / Tape For PWE(PCE) using 99.9% Pure copper tape / strip / foil Cu%99.90 C11000 Cu ETP Min thickness:0.001mm little order can accept Specification of red copper strip we supply: Strip: thick:0.15-3.0mm width:610mm Plate:thick:0.5-3mm width:610mm Length:2500mm

Below is a comprehensive list of our alloys arranged by type. More detailed information can be found on each alloys specific page. All of our products are purchased to normal industry standards and come with material test reports (MTR) also known as material certifications.

Aluminium Alloy Wheel Scrap Enriched with massive industry indulgent and understanding of this sector, we are involved in presenting a wide assortment of Aluminium Alloy wheel scrap. These scraps are widely used for the purposes of reusing and recycling. Available with us in bulk orders, our customers can get these from us at affordable costs. Also, we assure delivering these on time.

Hot selling high quality 99.9% aluminium Scrap Aluminium Wire Scrap Item Quality standard Si 0.2-0.6% Fe 0.35% Cu 0.1% Mn 0.1% Mg 0.45-0.9% Cr 0.1% Zn 0.1% Applications 1. Mainly used for melting ingot 2. Discontinuous melting with scrap 3. Easy control and operation 4. Fast melting 5. Energy saving This Scrap Aluminium is produced in the production of industrial waste. Such as: Scrap Aluminium Wire, Scrap Aluminium block and so on 6. It mainly used for drawing back non-ferrous metal typical material is: Wasted copper, aluminum, cable, aluminum stuff, wasted auto spare part, non-ferrous metal scrap, dross for printing, broken glass contains non-ferroous, electronic waste etc.

99.995 Zinc Ingot with Large Stock Application: Aviation, Electronics, Industrial, Medical, Chemical Standard:JIS, GB, DIN, BS, ASTM, AISI Purity: Custom Made Type: Zinc Bar Alloy: Custom Made Powder: Not Powder

Monel 400 (UNS N04400, NCu30) The structure of Monel 400 alloy is a high-strength single-phase solid solution. It is a corrosion-resistant alloy with the largest amount, the widest application and excellent comprehensive performance. This alloy has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium, and also has excellent corrosion resistance to hot concentrated lye. At the same time, it is also resistant to corrosion by neutral solutions, water, sea water, atmosphere, organic compounds, etc. An important feature of this alloy is that it generally does not produce stress corrosion cracks and has good cutting performance. The alloy has excellent corrosion resistance in fluorine gas, hydrochloric acid, sulfuric acid, hydrofluoric acid and their derivatives. At the same time, it is more corrosion resistant than copper-based alloys in seawater. â?² Acid medium: M400 is corrosion-resistant in sulfuric acid with a concentration of less than 85%. M400 is one of the very few important materials in durable hydrofluoric acid. â?² Water corrosion: M400 alloy not only has excellent corrosion resistance under most water corrosion conditions, but also pitting corrosion and stress corrosion are rarely found, and the corrosion rate is less than 0.25mm/a. â?² High temperature corrosion: The maximum temperature of M400 continuous work in the air is generally around 600�°C, and in high temperature steam, the corrosion rate is less than 0.026mm/a. â?² Ammonia: Due to the high nickel content of Monel 400 alloy, it can resist corrosion under anhydrous ammonia and ammoniation conditions below 585�°C. American standard designation: UNS N04400, Specifications: ASTM B164, ASTM B127, ASTM B165, ASTM B725, ASTM B163, ASTM B366, ASTM B164, ASTM B564, ASTM B164, AMS 4574, AMS 4675, AMS 4730, AMS 4731, AMS 4544, AMS 4574, AMS 4675, AMS 4730, AMS 4731, AMS 4544. German standard designation: W.Nr. 2.4360, Specifications: DIN 17743, DIN 17750, DIN 17752, DIN 17753, DIN 17754. Japanese standard designation: JIS NW4400, Specifications: JIS G4902, JIS G4903, JIS G4904, JIS G4905, JIS G4906, JIS G4907. Chinese standard designation: NS111, Specifications: GB/T 2054, GB/T 2055, GB/T 2056, GB/T 2057, GB/T 2058, GB/T 2059, GB/T 2060, GB/T 2061. We can provide the following the form:Monel alloy 400 coil; Monel alloy 400 strip;Monel alloy 400 plate; Monel alloy 400 sheets; Monel alloy 400 tube; Monel alloy 400 pipe; Monel alloy 400 flat; Monel alloy 400 bar GB: NS111 ;JIS:NW4400;UNS:N04400;W.Nr:2.436 This alloy is mainly used for 1. Seamless water pipes and steam pipes in power plants 2. Sea water exchanger and evaporator 3. Sulfuric acid and hydrochloric acid environment 4. Crude oil distillation 5. The pump shaft and propeller of the equipment used in seawater 6. The nuclear industry is used to manufacture equipment for uranium refining and isotope separation 7. Manufacture of pumps and valves used in the production of hydro

Monel 400 (UNS N04400, NCu30) The structure of Monel 400 alloy is a high-strength single-phase solid solution. It is a corrosion-resistant alloy with the largest amount, the widest application and excellent comprehensive performance. This alloy has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium, and also has excellent corrosion resistance to hot concentrated lye. At the same time, it is also resistant to corrosion by neutral solutions, water, sea water, atmosphere, organic compounds, etc. An important feature of this alloy is that it generally does not produce stress corrosion cracks and has good cutting performance. The alloy has excellent corrosion resistance in fluorine gas, hydrochloric acid, sulfuric acid, hydrofluoric acid and their derivatives. At the same time, it is more corrosion resistant than copper-based alloys in seawater. â?² Acid medium: M400 is corrosion-resistant in sulfuric acid with a concentration of less than 85%. M400 is one of the very few important materials in durable hydrofluoric acid. â?² Water corrosion: M400 alloy not only has excellent corrosion resistance under most water corrosion conditions, but also pitting corrosion and stress corrosion are rarely found, and the corrosion rate is less than 0.25mm/a. â?² High temperature corrosion: The maximum temperature of M400 continuous work in the air is generally around 600�°C, and in high temperature steam, the corrosion rate is less than 0.026mm/a. â?² Ammonia: Due to the high nickel content of Monel 400 alloy, it can resist corrosion under anhydrous ammonia and ammoniation conditions below 585�°C. American standard designation: UNS N04400, Specifications: ASTM B164, ASTM B127, ASTM B165, ASTM B725, ASTM B163, ASTM B366, ASTM B164, ASTM B564, ASTM B164, AMS 4574, AMS 4675, AMS 4730, AMS 4731, AMS 4544, AMS 4574, AMS 4675, AMS 4730, AMS 4731, AMS 4544. German standard designation: W.Nr. 2.4360, Specifications: DIN 17743, DIN 17750, DIN 17752, DIN 17753, DIN 17754. Japanese standard designation: JIS NW4400, Specifications: JIS G4902, JIS G4903, JIS G4904, JIS G4905, JIS G4906, JIS G4907. Chinese standard designation: NS111, Specifications: GB/T 2054, GB/T 2055, GB/T 2056, GB/T 2057, GB/T 2058, GB/T 2059, GB/T 2060, GB/T 2061. We can provide the following the form:Monel alloy 400 coil; Monel alloy 400 strip;Monel alloy 400 plate; Monel alloy 400 sheets; Monel alloy 400 tube; Monel alloy 400 pipe;Monel alloy 400 flat; Monel alloy 400 bar GB:NS111;JIS:NW4400;UNS:N04400;W.Nr:2.436 This alloy is mainly used for 1. Seamless water pipes and steam pipes in power plants 2. Sea water exchanger and evaporator 3. Sulfuric acid and hydrochloric acid environment 4. Crude oil distillation 5. The pump shaft and propeller of the equipment used in seawater 6. The nuclear industry is used to manufacture equipment for uranium refining and isotope separation 7. Manufacture of pumps and valves used in the production of hydrochlo

Monel K500 Monel alloy is a high-strength nickel-copper alloy with excellent corrosion resistance. Its main components are nickel and copper, and it also contains a small amount of beneficial elements such as aluminum, iron, and titanium. This alloy not only has corrosion resistance, but also has excellent mechanical properties, high strength, hardness and toughness, and can withstand high temperature, high pressure and corrosion in marine environments. Monel K500 alloy is widely used in marine and subsea oil and gas industry, machinery manufacturing, aerospace and other fields. Compared with other nickel-copper alloys, Monel K500 alloy is more corrosion-resistant. It can resist the erosion of nitric acid, seawater, alkaline solution and other media, and can also maintain stable performance under high temperature and high pressure conditions. Due to its low magnetic properties, Monel K500 alloy is also widely used in the electrical and electronic industries. In addition, it also has good weldability and processing performance, and can be formed and manufactured by various methods such as casting, forging, and cold working, so as to meet the manufacturing needs of complex workpieces in different industrial fields. In general, Monel K500 alloy has good corrosion resistance, high mechanical strength, excellent stability and comprehensive performance, and is a very excellent high-performance alloy material. With the continuous development and innovation of science and technology, Monel K500 alloy has a very broad application prospect in the future, and will bring more benefits to human production and life. American standard designation: UNS N05500, Specifications: ASTM B865, ASTM B164, ASTM B127, ASTM B165, ASTM B564, ASTM B865, ASTM B366, ASTM B865, AMS 4676, AMS 4676, AMS 4677, AMS 4677, AMS 4678, AMS 4678, AMS 4679, AMS 4679. German standard designation: W.Nr. 2.4375, Specifications: DIN 17743, DIN 17750, DIN 17752, DIN 17753, DIN 17754. Japanese standard designation: JIS NW5500, Specifications: JIS G4902, JIS G4903, JIS G4904, JIS G4905, JIS G4906, JIS G4907. Chinese standard designation: NS321, Specifications: GB/T 2054, GB/T 2055, GB/T 2056, GB/T 2057, GB/T 2058, GB/T 2059, GB/T 2060, GB/T 2061. We can provide the following the form:Monel alloyK500 coil; Monel alloy K500 strip;Monel alloy K500 plate; Monel alloy K500 sheets; Monel alloy K500 tube; Monel alloy K500 pipe;Monel alloy K500 flat; Monel alloy K500 bar GB:NS321; JIS:NW5500; UNS:N05500; W.Nr:2.4375

Monel R-405 alloy (UNS N04405) increases the sulfur content in the Monel 400 composition to enhance the machinability and become a free-cutting Monel alloy. Alloy 405 is an easy-to-machine version of Alloy 400. Alloy 405 adds a certain amount of sulfur, and the sulfide produced has chip breaking effect during machining, so it is suitable for automatic nut machine. Like Alloy 400, Alloy 405 is resistant to corrosion by seawater, steam, and alkaline solutions at elevated temperatures. Alloy 405 is a solid solution alloy that can only be hardened by cold working. This nickel-based alloy also exhibits good corrosion resistance, weldability and high strength. The alloy exhibits low corrosion rates in fast-flowing brine and seawater environments and is well resistant to stress corrosion cracking in freshwater environments. Good corrosion resistance makes it widely used in marine and non-oxidizing chloride solution environment American standard designation: UNS N04405, Specifications: ASTM B164, ASTM B127, ASTM B165, ASTM B725, ASTM B163, ASTM B366, ASTM B164, ASTM B564, ASTM B164, AMS 4674, AMS 7234. Chinese standard designation: NS111, Specifications: GB/T 2054, GB/T 2055, GB/T 2056, GB/T 2057, GB/T 2058, GB/T 2059, GB/T 2060, GB/T 2061. We can provide the following the form:Monel alloy405 coil; Monel alloy 405 strip;Monel alloy 405 plate; Monel alloy 405 sheets; Monel alloy 405 tube; Monel alloy 405 pipe;Monel alloy 405 flat; Monel alloy 405 bar