This is 3 pin to OBD2 OBD adapter cable for Fiat.Adaptor lead has a female OBD2 connector to 3 pin Fiat plug. This is only an adaptor and must be used in conjunction with hardware compatible with the vehicle.The 3 pin socket is found under the bonnet. You need this adaptor to convert from the standard 16 pin socket used on diagnostic interfaces. Our 3pin For Fiat 16 Pin Female Diagnostic Tool is a must-have tool for any car enthusiast or professional mechanic. This versatile adapter cable allows you to connect your OBD2 scanner to a wide range of vehicles, including Lancia, Alfa Romeo, and Fiat models.(normally before 2001, check your vehicle to ensure) Fitment: Fits for Fiat Alpha Romeo
The cable has two connectors: one is for GM 12 Pin connector, another is 16 Pin OBD OBDII connector. The quality cable can be used for converting connection from GM 12 Pin to OBD OBDII 16 Pin interface, allows you use OBD OBDII diagnostic tools working with your vehicles with 12 Pin interface. And connects a 16 pin OBD 2 diagnostic tool to a for GM car with 12 pin socket. Works with all for GM & Daewoo cars made after 1996 with a 12 pin diagnostic connector. OBD Connector It is an improvement over OBD-II in both capability and standardization. The OBDII Connector standard specifies the type of diagnostic connector and its pinout, In addition to the electrical signaling protocols available too, likewise the messaging format. It also provides a candidate list of vehicle parameters to monitor along with how to encode the data for each. There is a pin in the connector that provides power for the scan tool from the vehicle battery, which eliminates the need to connect a scan tool to a power source separately. The amount of diagnostic information available via Universal OBD Connector OBDII has varied widely since its introduction in the early 1980s versions of on-board vehicle computers, It also Early versions of OBDII would simply illuminate a malfunction indicator light or â??idiot lightâ?? if a problem was detected but would not provide any information as to the nature of the problem. Modern Universal OBD2 Connector OBD implementations use a standardized digital communications port to provide real-time data in addition to a standardized series of diagnostic trouble codes, or DTCs, which allow a person to rapidly identify and remedy malfunctions within the vehicle. Other Policies: 1. If you order in bulk, price can be negotiate. 2. We wholesale al kinds car obdii cables, such as: (lowest price in China)
Place of Origin:CN;GUA Application:Automotive Type:M12 Gender:female or male Brand Name:STA Gender:Male or Female Code type:A.B.C.D Shell Material:Copper/Zinc Core material:PA66 Terminal material:Phosphor copper PINS:2P,3P, 4P, 5P, 6P,8P,12P,17P Cable diameter:4mm-8mm IP degree:IP67 Temperature range:-40°C -- +80°C Mating cycle:more than 500cycles
Place of Origin:CN;GUA Application:Automotive Type:M12 Gender:female or male Brand Name:STA Gender:Male or Female Code type:A.B.C.D Shell Material:Copper/Zinc Core material:PA66 Terminal material:Phosphor copper PINS:2P,3P, 4P, 5P, 6P,8P,12P,17P Cable diameter:4mm-8mm IP degree:IP67 Temperature range:-40°C -- +80°C Mating cycle:more than 500cycles
Place of Origin:CN; Brand Name:CAZN Type:female or male Gender:Male or Female Code type:A/B/C/D Shell Material:Copper/Zinc Core material:PA66 Terminal material:Phosphor copper PINS:3P, 4P, 5P, 6P,8P,12P.17P Cable diameter:4mm-8mm IP degree:IP67 Temperature range:-40°C -- +80°C Mating cycle:more than 500cycles
Fasteners like wedge anchor, nylon anchor, sleeve anchor, heavy duty anchor, chemical anchor rod, tam anchor fastener, drop in anchor fastener, chemical anchor and stone under cut anchor, stone cladding clamp like chair type clamp, z clamp, adjustable clamp pin/split type and rcc clamp/ split type and other products like lightning arrestor and air termination..
This 10.4-inch stainless steel capacitive touch waterproof fully bonded embedded panel industrial control all-in-one self-service terminal is a feature-rich device. It is made of stainless steel material, offering excellent waterproof performance and durability, suitable for various harsh environments. Equipped with a 10.4-inch capacitive touch screen, this industrial control all-in-one self-service terminal provides precise touch operation and clear image display. The fully bonded technology eliminates the air layer, providing a more realistic visual effect. It also has waterproof performance, preventing the intrusion of liquids and dust, ensuring reliable operation of the device in wet or dirty environments. This embedded panel industrial control all-in-one self-service terminal has multiple functionalities, suitable for applications like self-service terminals. It supports multiple interfaces and communication methods, such as USB, RS232, and Ethernet, facilitating the connection of external devices and data transmission. Additionally, it features multi-touch capability, allowing multiple users to operate simultaneously, enhancing the user experience. This 10.4-inch stainless steel capacitive touch waterproof fully bonded embedded panel industrial control all-in-one self-service terminal also has durability and impact resistance. The stainless steel material effectively prevents corrosion and damage, ensuring long-term stable operation of the device. It also features high brightness display and wide viewing angles, suitable for various self-service scenarios, such as self-service vending machines and self-service inquiry terminals. Whether used as a self-service terminal or an embedded industrial control device, this 10.4-inch stainless steel capacitive touch waterproof fully bonded embedded panel industrial control all-in-one self-service terminal delivers stable and reliable performance and comprehensive functionality.
Description: The terminal pull force tester is especially designed for measuring pull forces of crimping connections, weld connections and many other possibilities. Simple LCD display for easy programming and read out, it provides standard interface for curve analysis and downloading test data. Force range: 500N(1000N) Resolution: 0.01N Accuracy: ±0.5% Power supply: nickel cyanide battery(22V AC changing 4 to 6 hours) Ambient temperature: 0 to 60 oC Ambient humidity:
40G&100G Transponder supports three 40G or 100G service access. The wide range of optical infrastructure solutions includes media conversion, signal repeating, lambda conversion. Function: Media conversion Signal repeating Lambda conversion Highlight: Support single channel 40Gbps/100Gbps large particle transmission Client side interface: support 3xQSFP28 module Line side interface: support 3xQSFP28 module Support DDM digital diagnosis Support ALS function Support LFP function 40G&100G Transponder supports three 40G or 100G service signals are relayed and amplified, and can be converted into three WDM standard wavelength optical signals, so that the multiplex unit can perform wavelength division multiplexing demultiplexing on optical signals of different wavelengths. A metropolitan wavelength division short-range transmission scheme suitable for 40G or 100G rates.
POWER AC Â 110 Â / Â 220V Â 50 0 Â HZ MOTOR AC220V 550W CRIMPING FORCE 2Ton FIT FOR ALL KINF OF TERMINAL OPERATION FOOT SWITCH SIZE 290W 290L 600H(mm) WEIGHT 45KG
With this cable you can connect the standardized OBD2 cable with the diagnostic interface of KTM. In addition, you can also connect other OBD2 diagnostic devices to the motorcycle. With the 6-pin to OBD2 adapter cable, you can connect your KTM motorcycle to a K-Line or CANbus compatible OBD2 diagnostic interface or ELM327 scanner. This adapter converts a 16-pin OBD2 standard plug into a 6 pin KTM plug. It works with various programs / apps and even with standard OBD2 readers. Compatible with various programs (e.g. TuneECU Read / delete the fault memory Reading of live engine data such as speed, rpm, temp, O2 sensor data, emissions, voltages, etc. Compatible motorcycles: K-T M 990 LC8, 1190 RC8, 690 Duke from 2011, 690 Supermoto,690 SMC and Enduro. K-T M Duke 125, Duke 200, Duke 390. K-T M RC 125,RC 200, RC 390 Please note: KTMs from 2016 on use mostly the Euro5 connector. If you are not sure, please contact us. Often a look under the seat is enough.
Selling of all Fire and safety items like fire extinguishers, mobile foam units, water monitors, foam monitors, hydrant valves, hose reel drums, hose boxes, cp/ rrl hoses, branch pipes, butterfly / sluice / non return valves, pressure switch, pressure gauges, sprinkler heads, flow switch, sprinkler gang bells, flexible drops, passive fire stopping material, intelligent addressable detectors, smoke detectors, heat detectors, flame detectors, sounders / hooters, manual call points, response indicators, control modules, microprocessor based conventional / addressable panels, solenoid valves, gas nozzles, actuators, safety shoes, safety goggles, safety helmets, safety gloves, safety masks, breathing apparatus, safety belts, emergency sirens, wind socks, eye wash showers and signage.
This 15.6-inch aluminum alloy fully bonded waterproof wall-mounted touch industrial control self-service terminal display signboard is a powerful industrial-grade monitor. It is made of aluminum alloy material and features full bonding technology, providing higher durability and reliability. This display is suitable for various industrial control and self-service terminal applications, such as query terminals, self-service solutions, and signboard displays. The display exhibits excellent waterproof performance, resisting water splashes and humidity to ensure stable operation in damp environments. It employs a waterproof sealing design, effectively preventing water from infiltrating the internal circuits, allowing it to adapt to various harsh environmental conditions. Furthermore, this display utilizes full bonding technology, eliminating the air gap and providing clearer and more realistic image display. It features high brightness and high contrast, enhancing image sharpness and color richness. The display also features a wall-mounted design, allowing for easy installation on walls or other support structures. It adopts a sturdy mounting bracket to ensure a secure fixation in the chosen location. This 15.6-inch aluminum alloy fully bonded waterproof wall-mounted touch industrial control self-service terminal display signboard also supports multi-touch functionality, offering more interaction options and operational features. It is equipped with multiple connection interfaces, such as HDMI, VGA, and USB, facilitating connection and integration with other devices. In summary, this 15.6-inch aluminum alloy fully bonded waterproof wall-mounted touch industrial control self-service terminal display signboard is a powerful, durable, and reliable industrial-grade monitor. It features waterproof performance, full bonding technology, wall-mounted design, and multi-touch functionality, making it suitable for various industrial control and self-service terminal applications.
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
12 Pin Round Connector A 12-pin round connector is an electrical connector with twelve circular pins or contacts that are used for transmitting electrical signals, power, or data. These connectors come in various sizes and configurations, and their usage can vary depending on the specific application. Features 4U Gold Plating Terminals Real Gold Plating, Strong Conductivity Without Oxidize, Extend Service Life International Certification We have passed a number of domestic and international certifications, such as China CQC (former CCC), Germany TUV, and USA UL. Multiple certificates are for your protection. Current 5-20A Optional Different Pin number meets different current and will meet power and signal used at the same time. Application Cases of Security Equipment Monitoring system, Information Security Door, Outdoor video monitor Applications 12-pin round connectors are used in a variety of applications, including: Audio and Video: They are commonly found in the audio-visual industry for connecting cameras, microphones, and other audio or video equipment. Industrial Control: In industrial settings, these connectors may be used for connecting sensors, control systems, and machinery. Automotive: Some automotive applications require 12-pin round connectors for power distribution, lighting, or data connections. Medical Equipment: In the medical field, these connectors can be used in medical devices and diagnostic equipment. Advantages Our wide range of circular connectors is always the ideal solution Reliable transmission of signals, data, and power thanks to plastic + metal housing Savings in connection times through innovative connection solutions for devices with all industry-standard protection classes The high degree of flexibility for individual adaptation to your requirements.
12 Pin Round Connector A 12-pin round connector is an electrical connector with twelve circular pins or contacts that are used for transmitting electrical signals, power, or data. These connectors come in various sizes and configurations, and their usage can vary depending on the specific application. Features 4U Gold Plating Terminals Real Gold Plating, Strong Conductivity Without Oxidize, Extend Service Life International Certification We have passed a number of domestic and international certifications, such as China CQC (former CCC), Germany TUV, and USA UL. Multiple certificates are for your protection. Current 5-20A Optional Different Pin number meets different current and will meet power and signal used at the same time. Application Cases of Security Equipment Monitoring system, Information Security Door, Outdoor video monitor Applications 12-pin round connectors are used in a variety of applications, including: Audio and Video: They are commonly found in the audio-visual industry for connecting cameras, microphones, and other audio or video equipment. Industrial Control: In industrial settings, these connectors may be used for connecting sensors, control systems, and machinery. Automotive: Some automotive applications require 12-pin round connectors for power distribution, lighting, or data connections. Medical Equipment: In the medical field, these connectors can be used in medical devices and diagnostic equipment. Advantages Our wide range of circular connectors is always the ideal solution Reliable transmission of signals, data, and power thanks to plastic + metal housing Savings in connection times through innovative connection solutions for devices with all industry-standard protection classes The high degree of flexibility for individual adaptation to your requirements.
Product Description: The Arduino/Genuino Uno can be programmed with the (Arduino Software (IDE)). Select "Arduino/Genuino Uno from the Tools > Board menu (according to the microcontroller on your board). For details, see the reference and tutorials.The ATmega328 on the Arduino/Genuino Uno comes preprogrammed with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files). You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar; see these instructions for details. Speed(MHz) 16MHZ Core Size (Number of Bits) 8 Bit RAM Size 2KBYTE ROM Type EEPROM Flash Number of Pins 28 Other Detail: Microcontroller ATmega328P Input Voltage (recommended) 7-12V Input Voltage (limit) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328P) EEPROM 1 KB (ATmega328P) Clock Speed 16 MHz LED_BUILTIN 13
Product Description: The Arduino/Genuino Uno can be programmed with the (Arduino Software (IDE)). Select "Arduino/Genuino Uno from the Tools > Board menu (according to the microcontroller on your board). For details, see the reference and tutorials.The ATmega328 on the Arduino/Genuino Uno comes preprogrammed with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files). You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar; see these instructions for details. Speed(MHz) 16MHZ Core Size (Number of Bits) 8 Bit RAM Size 2KBYTE ROM Type EEPROM Flash Number of Pins 28 Other Detail: Microcontroller ATmega328P Input Voltage (recommended) 7-12V Input Voltage (limit) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328P) EEPROM 1 KB (ATmega328P) Clock Speed 16 MHz LED_BUILTIN 13
