High Performance Naphthalene Superplasticizer For Concrete CAS No. 9008-63-3 Naphthalene superplasticizer Chemical name: �² Sodium naphthyl sulfonate formaldehyde condensate. Molecular formula: (c10h6ch2naso3) n, n is mainly 9-12. Joyreach Fdn Powder Naphthalene Water Reducing Admixture Superplasticizer for Concrete Package 25kg/50kg Naphthalene superplasticizer has good adaptability to various cements and improves the operability of concrete.FDN has the advantage of high water reducing ratio, non-delayed coagulation, non-air entraining and strong adaptability. It can improve the workability of concrete to a large extent so as to reduce the water consumption for blending. Meanwhile, it can improve the strength of concrete. It is widely used in concrete engineering: highway, railway, bridge, tunnel, power station, dam, high-rise building and other projects.It has good dispersion, water reduction and early-strength effect.Adding naphthalene series superplasticizer into ordinary concrete can improve the physical and chemical properties of concrete, improve the concrete strength, construction speed, project quality, technology and working conditions. 1. early strength admixture - improve construction progress; 2. retarding admixture - prevent cracking of large infrastructure such as airports and bridges; 3. pumping type admixture - transported by pump, such as high-rise buildings; 4. antifreeze admixture - used for winter construction. FDN-A High concentration product with sodium sulfate content no more than 5 percent. FDN-AI Middle concentration product with sodium sulfate content no more than 10 percent. FDN-AII Low concentration product with sodium sulfate content no more than 18 percent. FDN-23 sodium sulfate content no more than 23 percent,cheapest type to save cost. Usage method: --Powder 0.5%-1.0%, recommended dosage 0.75%; --Liquid is 1.0%-2.0%, and the recommended mixing amount is 1.5%. The mixing amount can be appropriately increased according to the grade of concrete. --Each batch of goods must be tested to meet the engineering requirements before use. 1. As the requirement of engineer,the dosage can be adjusted after testing. 2. It can be put into blender with mixing water,making mixing before concrete pouring,the plasticizing effect could be better.
High Performance Naphthalene Superplasticizer For Concrete CAS No. 9008-63-3 Naphthalene superplasticizer Chemical name: �² Sodium naphthyl sulfonate formaldehyde condensate. Molecular formula: (c10h6ch2naso3) n, n is mainly 9-12. Joyreach Fdn Powder Naphthalene Water Reducing Admixture Superplasticizer for Concrete Package 25kg/50kg Naphthalene superplasticizer has good adaptability to various cements and improves the operability of concrete.FDN has the advantage of high water reducing ratio, non-delayed coagulation, non-air entraining and strong adaptability. It can improve the workability of concrete to a large extent so as to reduce the water consumption for blending. Meanwhile, it can improve the strength of concrete. It is widely used in concrete engineering: highway, railway, bridge, tunnel, power station, dam, high-rise building and other projects.It has good dispersion, water reduction and early-strength effect.Adding naphthalene series superplasticizer into ordinary concrete can improve the physical and chemical properties of concrete, improve the concrete strength, construction speed, project quality, technology and working conditions. 1. early strength admixture - improve construction progress; 2. retarding admixture - prevent cracking of large infrastructure such as airports and bridges; 3. pumping type admixture - transported by pump, such as high-rise buildings; 4. antifreeze admixture - used for winter construction. FDN-A High concentration product with sodium sulfate content no more than 5 percent. FDN-AI Middle concentration product with sodium sulfate content no more than 10 percent. FDN-AII Low concentration product with sodium sulfate content no more than 18 percent. FDN-23 sodium sulfate content no more than 23 percent,cheapest type to save cost. Usage method: --Powder 0.5%-1.0%, recommended dosage 0.75%; --Liquid is 1.0%-2.0%, and the recommended mixing amount is 1.5%. The mixing amount can be appropriately increased according to the grade of concrete. --Each batch of goods must be tested to meet the engineering requirements before use. 1. As the requirement of engineer,the dosage can be adjusted after testing. 2. It can be put into blender with mixing water,making mixing before concrete pouring,the plasticizing effect could be better.
COMPANY PROFILE QUANZHOU TOGETHER ECO TECH CO.,LTD� are devoted to� Popularize 100% Recycled and Biodegradable Non-woven fabric, Provide quality solutions and customer satisfaction through valued-added products and services. biodegradable materials PLA SPUNBOND NON WOVEN FABRIC PLA meltblown nonwoven fabric PLA/PET/RPET SPUNLACE NON-WOVEN RPET Spun-bond nonwoven fabric PET spunbond non-woven fabric RPET stitchbond non woven fabrics SMS/SMMS/SSMMS NON-WOVEN FABRIC FACE MASK.DIAPER.MEDICAL PRODUCT MATERIAL RPET stitchbonded nonwoven bag PLA non woven shopping bag RPET spunbonded non-woven bag What is polylactic acid (PLA)? PLA is not plastic. It is derived from nature. Starch is extracted from plants such as corn and cassava and fermented by microorganisms to produce lactic acid. Lactic acid undergoes an advanced polymerization process to produce a 100% green and safe new polymer material called polylactic acid (PLA). Products made from this material are healthy and safe, non-toxic and odorless, and have no harm to the human body. In addition, if the product is discarded under composting conditions, it can be completely decomposed by microorganisms, eventually generating carbon dioxide and water, and returning to nature. The environment does not cause any pollution, so PLA is recognized as a â??green materialâ?? for low-carbon environmental protection and sustainable development in the 21st century. PRODUCT DESCRIPTION Material: 100% Polylactid Acid Technics : Spunbonded� Weight:� 10-250GSM Width: 160-300-320cm or customized Color:� customized MOQ:� 1tons/white, 5tons/other color Special Process: with UV/Laminated(PP+PE) / Printed /Hydrophilic/pre-cut/Fire treatment Hard or soft finition with nice and shinny surface Main Uses (1) medical and health care cloth: surgical clothing, protective clothing, sterilizing cloth, mask, diapers, sanitary napkin, etc; (2) home decoration fabric: wall cloth, tablecloth, bedspread, bedspread, etc; (3) follow the cloth: lining, bonding,, shaping cotton, various synthetic leather soles, etc; (4) industrial fabrics: filtration materials, insulating materials, cement packaging bags, geotextiles, covering cloth, etc; (5) agricultural cloth: crop protection cloth, seedling cloth, irrigation cloth, thermal insulation curtain, etc; (6) other: space cotton, thermal insulation materials, linoleum, cigarette filters, bags and tea bags, etc.
Miniature Circuit Breaker Automatic Assembly and inspecting line MCB Automatic Assembly and inspecting line Keyword: Miniature Circuit Breaker Automatic Assembly, Miniature Circuit Breaker, Automatic Assembly line, Assembly Machine, Assembly Production Line Product Introduction Basic operation process: ï?¼Loading by AGV robots, printing QR codes based on the product work order issued by the SAP system, and then separating the upper and lower shells. ï?¼Bottom coating of the upper shell: The installation of three components is completed through ten processes, and after each assembly is completed, there is a corresponding installation accuracy testing process to ensure that the assembly is completely qualified. ï?¼Installation of lower shell components, upper and lower shell assembly: A total of 25 processes are used to install 12 components. After each part is assembled, guide pins are used to ensure the upper and lower assembly. After the installation of internal components is completed, the product's on/off function is tested. After passing the test, rivets are installed, pressed again, and the screws are removed. All installations are checked, and after passing the test, they are transferred to the inspection station. ï?¼Unipolar products undergo instantaneous detection, delay detection, cooling tower and other unit inspections, and are then labeled with QR codes and covers before being transferred to the next workstation. ï?¼Multi pole products require 9 steps of multi pole assembly, and after assembly, a second delay is performed to verify the stability and reliability of the product ï?¼Finally, it is transferred to the automatic packaging unit through pressure resistance testing, transfer printing, laser labeling, and buckle installation. The specific parameters: (1) Equipment input voltage: 220V �± 10%, 50Hz; (2) The equipment has functions such as automatic shell loading, lid opening, assembly of arc extinguishing plates, magnetic guide plates, handle springs, base springs, positioning pins, handles, jump buckles, locks, coil components, iron core components, wiring columns, adjustment screws, arc extinguishing covers, CCD recognition, lid closing, identification of qualified and unqualified products, assembly of cutting processes, online detection, real-time monitoring, component life monitoring, data storage, MES system and ERP system networking, parameter arbitrary formula, smart energy analysis and energy-saving management system, intelligent equipment service big data cloud platform, etc. (3) Theoretical production effeciency: 2 seconds per unit; Daily production of approximately 14400 pieces/8 hours; (4) This device has the function of power-off to save data for 30 days, making it easy to manage production data; (5) This device adopts touch screen operation, has a computer communication interface, and printing function
Miniature Circuit Breaker Automatic Assembly and inspecting line MCB Automatic Assembly and inspecting line Keyword: Miniature Circuit Breaker Automatic Assembly, Miniature Circuit Breaker, Automatic Assembly line, Assembly Machine, Assembly Production Line Product Introduction Basic operation process: ï?¼Loading by AGV robots, printing QR codes based on the product work order issued by the SAP system, and then separating the upper and lower shells. ï?¼Bottom coating of the upper shell: The installation of three components is completed through ten processes, and after each assembly is completed, there is a corresponding installation accuracy testing process to ensure that the assembly is completely qualified. ï?¼Installation of lower shell components, upper and lower shell assembly: A total of 25 processes are used to install 12 components. After each part is assembled, guide pins are used to ensure the upper and lower assembly. After the installation of internal components is completed, the product's on/off function is tested. After passing the test, rivets are installed, pressed again, and the screws are removed. All installations are checked, and after passing the test, they are transferred to the inspection station. ï?¼Unipolar products undergo instantaneous detection, delay detection, cooling tower and other unit inspections, and are then labeled with QR codes and covers before being transferred to the next workstation. ï?¼Multi pole products require 9 steps of multi pole assembly, and after assembly, a second delay is performed to verify the stability and reliability of the product ï?¼Finally, it is transferred to the automatic packaging unit through pressure resistance testing, transfer printing, laser labeling, and buckle installation. The specific parameters: (1) Equipment input voltage: 220V �± 10%, 50Hz; (2) The equipment has functions such as automatic shell loading, lid opening, assembly of arc extinguishing plates, magnetic guide plates, handle springs, base springs, positioning pins, handles, jump buckles, locks, coil components, iron core components, wiring columns, adjustment screws, arc extinguishing covers, CCD recognition, lid closing, identification of qualified and unqualified products, assembly of cutting processes, online detection, real-time monitoring, component life monitoring, data storage, MES system and ERP system networking, parameter arbitrary formula, smart energy analysis and energy-saving management system, intelligent equipment service big data cloud platform, etc. (3) Theoretical production effeciency: 2 seconds per unit; Daily production of approximately 14400 pieces/8 hours; (4) This device has the function of power-off to save data for 30 days, making it easy to manage production data; (5) This device adopts touch screen operation, has a computer communication interface, and printing function
Product Description OVERVIEW Level of Play Elite Fit Profile Low, Medium, High Volume Weight 899 grams (Size 9) Heritage JetSpeed FT2 / FT1 Model Number JSFT4P Available Sizes 4.0-11.5 Available Widths Tapered, Regular, Wide Specifications KEY TECHNOLOGIES One-Piece Boot Compared to its two-piece counterparts, the One-Piece design is lighter, better at transferring energy and better wraps around the foot for an improved fit. What does this mean? One-Piece boots make players quicker and faster. Learn even more about it here. SpeedBlade XS Tongue System An easy and secure clip system gives you the ability to use one of three aftermarket CCM tongues. Slim is the lightest and slimmest, which reduces weight and increases internal volume. Regular is the most similar to the stock tongue but comes with D3O Smart Foam for top-tier protection. Extra is the thickest and most protective, which also reduces internal volume. View all of the options here. Asymmetrical Toe Cap A new, lower-profile design provides an even better foot-to-ice connection with a comfortably snug feel. Plus, traditional toe caps reduce energy transfer since the feet are not as secure as they could be. BOOT Construction 3D One-Piece Speed Material RocketFrame Composite Heat Moldable Yes Tongue Replaceable, Asymmetrical Metatomic XS Tendon Guard Injected, Reinforced Facing Low Profile Laces Unwaxed Midsole Composite Outsole None LINER Lining Material TotalDri+ Abrasion Reinforcement Yes Collar Padding Yes Ankle Padding ADPT Memory Comfort Foam Footbed CCM Ortholite UltraLite RUNNER Construction Step Steel Black +4mm Removable Yes Material High-Grade Steel Finish Carbon Chrome Height 21mm Radius 10' HOLDER Construction SpeedBlade XS Release Mechanism Tool-less Dial Branch Office Best Scooter Store Menara Karya 23rd floor Jl. H.R. Rasuna Said, Blok X-5, Kv. 1-2 Jakarta 12950 - DKI Jakarta Indonesia Phone : +62 (21) 57945487 Fax : +62 (21) 57944748 Whatsapp : +62 852 1840 2436 Instagram : @bestscooterstore Website : bestscooterstore.com
Application The CLRT-01 Carbon Dioxide Volume Tester is a crucial tool in the beverage industry, focusing on gauging carbonation levels, which significantly impact the bubbly and sensory qualities of drinks, thus influencing product excellence and customer contentment. Specially crafted for CO2 volume assessment, the CLRT-01 employs an automated process to uncover the connection between pressure and temperature, a pivotal factor in thorough beverage quality analysis. By seamlessly merging these elements, it offers a profound understanding of carbonation dynamics, granting manufacturers the ability to maintain consistency, adapt formulations, and provide effervescence that resonates with consumer preferences and brand achievement. Automatic Testing and Shaking The tester automates the traditional manual process: Piercing the bottle cap â?? Opening the vent valve to release pressure â?? Closing the vent valve â?? Vigorously vibrating for 40 seconds â?? Recording the stabilized MPa pressure (while measuring liquid temperature) â?? Obtaining the carbon dioxide gas capacity test results. Technical Features 1.This unit is under precise PLC control (at an industrial-grade stability level) and operated through an HMI touch screen interface. 2.Agitating the sample bottle is achieved using a servo motor and gearbox transmission mechanism. 3.The design incorporates anti-leak features and includes accurate temperature and pressure measurement. 4.The process involves automated piercing and shaking. 5.Displacement and speed during piercing are controlled for accuracy. 6.The shaking parameters, including frequency and duration, can be customized. 7.Test results are guaranteed accurate due to the implementation of a highprecision pressuresensor. 8.Real-time temperature display is enabled by a precision temperature sensor. 9.Post-test, the carbonation volume is automatically and presented. 10.Designed to prevent leaks, this versatile tester is suitable for both bottles and cans. 11.(Optional) A microprinter can be incorporated for additional functionality. 12.(Optional) The inclusion of an RS 232 port and professional software provides further versatility. Main Parameters Test Range 0~1MPa Resolution 0.01KPa Shaking Speed Adjustable Piercing Speed 5mm/s (other available) Sample Height â?¤ 350mm (other available) Temp. range 0 ~ 30 Shaking time 40s (other available) Resolution 0.1
Product overview 1. It is composed of polysiloxane, dispersing agent, stabilizer, etc.; 2. It is highly compatible with foaming medium, with rapid defoaming speed and excellent bubble elimination performance; 3. It is easy to disperse in water. Technical specifications Appearance: White to yellowish emulsion pH value: 6ï½?8 Effective ingredients: 99% Performance characteristics 1. Dyeing at normal temperature in textile slurry; 2. Industrial water treatment, coating and pesticide defoaming; 3. Elimination of other aqueous phase bubble with quick defoaming as required; 4. For the oilfield drilling fluid defoaming, the reversion rate of slurry is close to 100%. Usage tips The antifoaming agent has excellent foam elimination and inhibition performance, and can be added to product after foam generation or as foam inhibition components. The additive amount of defoaming agent can be 10~100ppm. The optimal additive amount is determined by customers through test according to specific condition. Defoaming agent product can be used directly or after dilution. If the product can be fully stirred and dispersed in foaming system, and can be directly added without dilution. If it needs to be diluted, it can't be directly diluted with water, otherwise the layering, demulsification, etc. easily occur, thus influencing the product quality. For consequences generated due to direct dilution with water or process of use of the product in other incorrect methods, our company doesn't undertake the responsibilities. Packing and storage �· The product is packaged with 25kg, 50kg, 120kg or 200kg plastic bucket. In case of special requirements, the bucket can be customized through consultation according to the special requirements. �· Its storage temperature shall be at 5~30â??. It shall not be placed near heat sources or insolated in the sunshine. The acid, alkali, salt, etc. shall not be added to product. The container shall be sealed in case of non-use to avoid being polluted by harmful bacteria. If it is layered after being placed for a long time, it shall be stirred evenly, and its using effect isn't influenced. The product would not freeze below 0 . In case of freezing, its using effect isn't influenced after melting and stirring. The guarantee period of product at the suggested storage temperature and without sealing, lasts for 12 months from the production date.
This system contains below parts and its description is as below: Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type ) Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images. DM water tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only. Blue Color PU Tubing. : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref. Small Plastic Connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images. Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image. Other Instructions: The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage. Keep minimum distance in between DM water tank and Lead acid Battery. When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point. When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell. Package Contents: Water Storage Tank Pipeline /Water tubes Feed water Pump End Plugs Battery watering Plug
This system contains below parts and its description is as below: Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type ) Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images. DM water Tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only. Blue color PU Tubing. : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref. Small Plastic Connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images. Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image. Other Instructions: The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage. Keep minimum distance in between DM water tank and Lead acid Battery. When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point. When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell. Package Contents: Water Storage Tank Pipeline /Water tubes Feed water Pump End Plugs Battery watering Plug Auto Feed Water Control Unit
Quality Product : Lowest Price : Benefit to the end user : Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type ). Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images. DM water tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only. Blue color PU tubing : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref. Small Plastic connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images. Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image. Other Instructions: The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage. Keep minimum distance in between DM water tank and Lead acid Battery. When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point. When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell. Package Contents: Water Storage Tank Pipeline /Water tubes Feed water Pump End Plugs Battery watering Plug Auto Feed Water Control Unit
Product Features * We have dedicated server to view online through Mobile / Laptop absolutely Free. * No Need and Static IP or DDNS Port Forwarding. It works with help of Unique ID. * It has 16 Video input, Four Audio Input and with HDMI Output Port with VGA and BNC. Features: 1. H.264 compression format 2. Mobile monitoring through their own software 3. One RJ45 / Lan / Ethernet Connector to connect DVR with your Modem. 4. Audio and video recording and play back simultaneously, 5. support NTSC/PAL video system 6. 16 CH video inputs, 1CH monitor output, 1CH spot monitor output, 1CH VGA output(1280*1024) 7. 4CH audio inputs, 1CH audio output 8. High quality image, brightness, contrast, sharpness and color adjustable for each channel 9. Support video sequence display 10. Display modes: PIP, FULL, QUAD, 8 SPLIT, 9/16 SPLIT 11. Recording modes: always recording, manual recording, schedule recording, sensor recording and motion recording 12. Detailed event log support 13. Searching modes: time/date searching, event searching, urgent searching 14. Support fast forward and rewind: x2, x4, x8, support jog-shuttle operation 15. Back up modes: network backup, USB back up 16. Support USB mouse and infrared remote controller operation 17. Support 2 SATA port upto 2 TB of HDD 19. Multiplex operation: live/recording/playback/network can be operated at the same time 20. Telemetry network control: live view, playback, recording and so on 21. Dimension: 25 x 23 x 4.5cm/9.84 x 9.05 x 1.77"(L x W x H) In The Box 1 x ZVision 16 Channel H.264 DVR Network Digital Video Recorder with HDMI Port 1 x Mouse 1 x Charger 1 x Power cord 1 x Remote control 1 x CD Disk
Product Features * We have dedicated server to view online through Mobile / Laptop absolutely Free. * No Need and Static IP or DDNS Port Forwarding. It works with help of Unique ID. * It has 16 Video input, Four Audio Input and with HDMI Output Port with VGA and BNC. Features: 1. H.264 compression format 2. Mobile monitoring through their own software 3. One RJ45 / Lan / Ethernet Connector to connect DVR with your Modem. 4. Audio and video recording and play back simultaneously, 5. support NTSC/PAL video system 6. 16 CH video inputs, 1CH monitor output, 1CH spot monitor output, 1CH VGA output(1280*1024) 7. 4CH audio inputs, 1CH audio output 8. High quality image, brightness, contrast, sharpness and color adjustable for each channel 9. Support video sequence display 10. Display modes: PIP, FULL, QUAD, 8 SPLIT, 9/16 SPLIT 11. Recording modes: always recording, manual recording, schedule recording, sensor recording and motion recording 12. Detailed event log support 13. Searching modes: time/date searching, event searching, urgent searching 14. Support fast forward and rewind: x2, x4, x8, support jog-shuttle operation 15. Back up modes: network backup, USB back up 16. Support USB mouse and infrared remote controller operation 17. Support 2 SATA port upto 2 TB of HDD 19. Multiplex operation: live/recording/playback/network can be operated at the same time 20. Telemetry network control: live view, playback, recording and so on 21. Dimension: 25 x 23 x 4.5cm/9.84 x 9.05 x 1.77"(L x W x H) In The Box 1 x ZVision 16 Channel H.264 DVR Network Digital Video Recorder with HDMI Port 1 x Mouse 1 x Charger 1 x Power cord 1 x Remote control 1 x CD Disk
Product Specification Model River-F Plus Device, Measurement Range FRONT- 3000 Mtr. DEPTH- 1200 Mtr. Brand GER DETECT Display Type Digital Minimum Order Quantity 1 Set Product Description RIVER-F PLUS Device Long Ranger Water Detector For the explorers of wells and underground water. GER DETECT Company provide you with the latest technology specifications and high-resolution techniques and discrimination. GER DETECT Company put all the high-tech in device to be the first device among other long range devices the specifications and features provide the navigator great effort in the search-and-water exploration. The Long Range System The latest device to detect underground water and artesian wells RIVER - F a device with multiple features searching underground water and artesian wells 1- Fresh water Search system 2- Natural water search system 3- Salty water search system RIVER - F, in its new version, allows users to operate two systems the touch system, and the keyboard system This version is also characterized by several functions It operates in six different languages (German - English - French - Italian - Spanish, and Arabic) The user can choose the type of soil desired in the search area (natural - clay - rocky - sandy - mixed, and mineral). This feature is designed for the user to obtain more accurate results. It operates with a front range up to 3000 square meters and 1200 meters of depth. The device allows the user to select a suitable front range of the search area to be covered (500 - 1000 - 1500 - 2000 - 2500 - 3000) square meters. It's got a digital compass to help the user set the north and south directions. It's got a settings menu (Sound Adjustment - brightness adjustment, and the device information) Technical and operational steps of the smart digital screen for signal tracking how to use River-F Plus by keypad how to use River-F Plus by touch screen River-F Plus Technical Specification (1) Small size and easy to use. (2) Touch screen to show full search data. (3) The Device depth of 1200 meters. (4) Possibility of identifying the target depth underground. (5) Front range up to 3000 meters with the possibility of determine the desired front Range. (6) Determine the Target to be searched for. (7) The user can choose the type of soil desired in the search area (8) It operates in six different languages (German - English - French - Italian - Spanish, and Arabic) (9) Certificate of origin and warranty for two years from the date of purchase Germany industry first class. (10) Full weight of the device with accessories only (6 kg).The device fit all circumstances and different terrain.
RO technology introduction : The principle of RO technology is that under the action of higher osmotic pressure than the solution, RO water equipment will leave these substances and water according to other substances can not pass through the semi-permeable membrane. Reverse osmosis, also known as reverse osmosis, is a membrane separation operation that uses the pressure difference as a driving force to separate the solvent from the solution. Pressure is applied to the material liquid on one side of the membrane. When the pressure exceeds its osmotic pressure, the solvent will reverse osmosis against the direction of natural osmosis. Thus the low pressure side of the membrane to get through the solvent, namely osmotic liquid; The high pressure side produces a concentrated solution, that is, a concentrated solution. For example ,if the seawater is treated with reverse dredging, fresh water is obtained on the low pressure side of the membrane and brine is obtained on the high pressure side. Advantages and Applications : RO Reverse osmosis equipment has been developed rapidly in the past 20 years due to its advantages of good water quality, low energy consumption, simple process and easy operation. The main application areas of reverse osmosis equipment include: 1. Flowers and aquaculture water: flower seedling and tissue culture; Fish xing buckwheat colonization, beautiful fish and so on. 2. Fine chemical water: cosmetics, detergent, biological engineering, genetic engineering, etc 3. Alcohol drink water: liquor, beer, wine, carbonated drinks, tea drinks, dairy products, etc 4. Electronics industry ultra-pure water: monocrystalline silicon semiconductor, integrated circuit block, liquid crystal display, etc 5. Pharmaceutical industry water: pharmaceutical preparations, infusion, extraction of natural substances, traditional Chinese medicine drinks, etc 6. Quality drinking water: community, hotels, airports, schools, hospitals, enterprises and institutions 7. Industrial production water: washing glass water, automobile, electroplating ultra-pure water, coating, paint, paint, boiler softening water, etc 8. Seawater brackish water desalination: making drinking water from islands, ships and saline-alkali areas 9. Water for textile and papermaking: water for printing and dyeing, water for jet loom, water for papermaking, etc 10. Water for food processing: cold drink food, canned food, livestock and meat processing, vegetable finishing, etc 11. Circulating cooling water: air conditioning, smelting, water cooled air conditioning 12 .Swimming pool water purification: indoor natatorium, outdoor elephant view pool, etc 13. Drinking water: purified water, mineral water, mountain spring water, bucket bottled water, etc.
PP Spunbonded Nonwoven Fabrics, Non Woven Fabric Mattress Cover, Disposable Mattress Cover REASONS TO CHOOSE MATTRESS: PP spunbonded nonwoven Fabrics 1ï¼?Material: 100% polypropylene 2ï¼?Weight: 15~200gsm 3ï¼?Width: within 320cm 4ï¼?Color: any colors available 5ï¼?factory direct: low price, steady supply PRODUCT SPECIFICATIONS: Item PP spunbonded nonwoven fabrics material 100% polypropylene technics Spun-bonded design dot color any color acceptable weight 15~200gsm width within 320cm length according to customer's requests roll weight around 35kg or customized MOQ 1000kgs 20'FT container around 4~5 tons ( the details quantity is up to the diameter of the roll) 40â??FT container about 10-11tons (the details quantity is up to the diameter of the roll) 40'HQ container around 11~12 tons ( the details quantity is up to the diameter of the roll) delivery time within 3 weeks upon receipt of advance payment A. T/T, 30% deposit, balance against copy of B/L B. Confirmed irrevocable L/C at sight packaging in the roll, inside the paper tube, outside PE film feature waterproof, mothproof, eco-friendly, breathable, anti-static, anti-bacteria, anti-pull, tear-resistant, flame-retardant application home textile, hospital, agriculture, bag, hygiene, garment, car, industry, shoes,interlining,lining,bedding, and so on. factory Qingdao yihe packing products manufacturer We are a factory specializing in producing PP spun-bonded nonwoven fabrics, and PP nonwoven bags, and have been exported for many years. Our products are superior, and are very competitive, because we are manufactory, we are the source. Our products are exported mainly to Europe, North America, Japan, South Korea, Middle East and so on. Should you be interest of any of items, please let us know. We shall be glad to give you our lowest quotations upon receipt of your detailed requirements. Qingdao Yihe is specializing in Baby Diaper Non Wovens Fabrics and Sanitary Napkin Non Wovens Fabrics. The transportation is convenient, the location is properly. We are Pet Pads Non Wovens Fabrics Manufacturer, and our Polypropylene Spun bonded Non woven Fabrics are guaranteed.
Jump Rope Description: Most consider a good long jog to be the ultimate form of exercise. Yet, jumping rope is known to have some benefits over running. Because the body's weight is distributed on the balls of the feet when landing, jumping rope is less stressful on the knees and ankles.Jumping rope has a lower-impact on the joints and lessens the chances of injury. This type of exercise is great at building cardiovascular stamina. The entire body will benefit, including the arms, shoulders, legs, and wrists. Jumping rope also builds coordination and precision. Boxers are well known for jumping rope in order to improve footwork. Even mixed martial artists use jump ropes to compliment their regimens. Jumping rope does not require much. A single piece of very inexpensive equipment, and an area to jump is all a user needs. Just you alone and a small space. Grab a rope, and go. 1) Skipping method is used before the soles of the feet takeoff and landing, can not remember the toe or heel landing, so as to avoid brain shock, when jumping in the air, not extreme bending the body, and become the natural bending posture. Jump, breathing naturally rhythm. 2) Hand rope method hands respectively hold the rope ends, usually with a foot hold of the rope, arms elbow will arm lift flat, the rope was straightened at suitable length. 3) Rope swinging forward swing, big arm near the elbow slightly on both sides of the body, the upper arm abduction, the approximate level, wrist force for rotation abduction, the hands circle action in the side of the body, and each swing once, the rope from the back up and down, swing a week, the rope. Speed and hand rope is proportional to the speed, shaking more quickly, then the rope swing faster. 4) Stop rope forward roll, kick out, before the soles of the feet off the ground, heels make rope stopped at the footbackward roll, then after a foot, heel, sole on the ground, so that the rope stop in the soles of the feet. 5) Should be gradual exercise.Start practicing rope skipping, action should be slow to fast, from easy to difficult. All kinds of action learning first single rope skipping, and then learn more complex or group of people jumping rope skipping movements. Here are some of the brilliant benefits: 1. Easily adjustable length to fit both kids and adults. 2. Conveniently lightweight for perfect portability. 3. Improve speed and coordination. 4. Use the tried and true exercise of jumping to improve your fitness level, build strength and endurance and lose weight. Bingehua specializes in the production and export of fitness accessories, body-sculpting and power training goods, mainly including yoga ball, Resistance Band Loop, Half Balance Ball, etc. Our own factory was founded more than 10 years.
Hydraulic end assembly AH0501010500 AH35001-05.00 Sealing washer AH0501010203 AH35001-02.03 Crankshaft assemble AH1301010200 AH36001-02.00 Oil seal ring AH1301010405 AH36001-04.21 Adapter connectorZG2-1/2â?³ AH1001010807 AH33001-08A.07 Hydraulic end assembly AH0801010500 AH34001-05.00 Sealing washer AH0801010203 AH34001-02.03 Crankshaft assemble AH1601010100 AH37001-01.00 O-ring �?190�?3.55 530301011900035507 GB3452.1-82 Short circuitZG2-1/2â?³-NPT2-1/2 AH1001010808 AH36001-08C.04 Hydraulic end assembly AH1001010500 AH33001-05.00 Sealing washer AH1001010203 AH33001-02.03 Pinion Shaft assemble AH1301010300 AH36001-03.00 Two-lip seal 5"X6.25"X0.625" AH1301010406 AH36001-04.08A Flexible pipe �¦22�?�¦37 AH1001010180001 L=1500 Exhaust filter assembly AH0501011400 AH35004-11.00 Inner ring AH0501010204 AH35001-02.04 Pinion Shaft assemble AH1601010200 AH37001-02.00 Locking spring AH1301010407 AH36001-04.13 Gladhand �¦22�?�¦37 AH100101080900 AH33001-08.18.00 Exhaust filter assembly AH1001011900 AH33014-04.00 Inner ring AH0801010204 AH34001-02.04A Crossing Head Assemble AH1301010400 AH36001-04.00 Splash guard AH1301010408 AH36001-04.10 90�°Elbow NPT1â?³ AH1001010810 AH33001-08.16 Cross head assembly AH0501010400 AH35001-04.00 Inner ring AH1001010204 AH33001-02.04 Hydraulic End Assemble AH1301010500 AH36001-05A.00 Extension rod AH1301010409 AH36001-04.11 Adapter connector NPT2-1/2³ AH0801020801 AH34001-08B.07 Cross head assembly AH0801010400 AH34001-04.00 Outer ring AH050101020500 AH35001-02.05.00 Power end lubrication assembly AH1301010600 AH36001-06C.00 Crosshead pin AH1301010410 AH36001-04.12A Sealing washer AH1001010814 AH36001-08B.09 Cross head assembly AH1001010400 AH1001010400 Outer ring AH080101020500 AH34001-05.00 Base Seat AH1301010700 AH36001-07K.00 O-ring �?160�?7 530301011250070000 GB3452.1.-82 NPT1â?³Flange AH1001010815 AH36001-08B.10 Pinion shaft assembly AH0501010300 AH35001-03.00 Outer ring AH100101020500 AH33001-02.05.00 Spray Pump Assembly AH1301010800 AH36001-08C.00 Bolt M20�?65 T502-6005K T52-6005K Bead apex A-3708 140301012031500000 GB1171-74 Pinion shaft assembly AH0801010300 AH34001-03.00 connecting rod AH0501010206 AH35001-02.06 Sealing washer AH10010109 AH33001-09 Sealing gasket AH1301010411 AH36001-04.15 Flexible pipe �¦38�?�¦53 AH100101080002 �¦38�?�¦53-L=750 Pinion shaft assembly AH1001010300 AH33001-03.00 connecting rod AH0801010206 AH34001-02.06 Breather Cap T515-1001.00 T515-1001.00 O-ring 160�?7 530301011600070000 GB3452.1-82 90 Elbow
Definition: A type of hidden color carbon paper with a direct copy and direct color capability is carbonless copy paper, also known as CCP, Non-carbon copy paper, or NCR paper. In order for the micro-capsule in the pigment and oil solution to overflow and come into touch with the color development agent following the dyeing reaction, it must be subjected to an external force. mostly used for bills,continuous receipts, multi-link forms, general business receipts.Both blue and black picture carbonless copy paper is available. Characteristics: 1. Carbon pad free "carbon paper," direct writing is convenient and time-saving, carbon copy number 2-6 pages, and electric printing 2-10 pages, all of which may significantly increase job efficiency and satisfy modernization needs. 2: Clear, brilliant, non-fading, copy-writing that can thwart change and copying 3: Keep your hands clean and avoid contaminating your clothes or other paper products 4:Colorful and simple to distinguish processing. 5. Excellent paper with a smooth surface, superior strength to color paper weighing 28 grams, durability, and vivid printing colors 6:Safe and dependable, does not include any hazardous raw chemicals, and color graphics can be preserved for up to 15 years after production Applications : 1: Documents primarily use carbonless paper. Carbon-free carbon paper has been used for all previously existing invoices, contracts, treaties, and other legal effects of formal documents. Since traditional documents are merely plain paper, a copy layer must be added underneath them. Contrarily, special paper is used to bind carbon-free paper 2: In the case of the triple carbon-free paper receipt, it can be divided into upper paper, middle paper, and lower paper. The top paper is also known as CB Coated Back. Micro-capsules containing force-sensitive pigment oil are coated on the back of the paper. The medium paper is also known as the double Coated paper (code CFB, that is, Coated Front and Back). The front of the paper is coated with a chromogenic agent and the back is coated with micro-capsules containing force-sensitive pigment oil. The bottom paper is also known as the Coated paper (code CF, that is, Coated Front) the paper surface is coated with only the color agent. Self-Contained paper (SC, self-contained) is contained in a micro-capsule layer coated with chromatin oil on the back and chromatin and micro-capsule contained in chromatin oil on the front. 3:The upper paper and the lower paper do not have the carbon copy effect, only the medium paper has the carbon copy effect. In the use of non-carbon paper printed documents are usually equipped with a small piece of cardboard separated on the joint document, so as to avoid excessive writing force, resulting in other joint documents under the carbon copy. 4:Carbonless paper has roughly four colors: White/red/blue/green and other four colors, to distinguish the role of the joint order.
2.Technical parameters: 1. Box size in the laboratory: DL-120LA W1200 * D1000 * H500 (mm), Approximate dimensions: 2300 * 1300 * 1400mm, 2 standard temperatures, Laboratory temperature: nss acss 35 ± 1 /pass 50 ± 1 Pressure bucket humidity: nss acss 47 ± 1 /pass 63 ± 1 , Salt water temperature: 35 ± 1 It can be heated without water, 3 volumes, Laboratory capacity: 800L Salt water tank capacity: 40L, 4 compressed air, Compressed air pressure: 1.00 ± 0.01kgf/c 5 spray volume: 1.0-2.0ml/80c /h, 6 spray mode: continuous spray, timed spray, programmable spray, intermittent spray, demisting in the box, 7. Power supply: AC220V 50Hz/20A, 8. Material: The entire PVC board is made, and the salt spray testing machine adopts advanced three-dimensional reinforcement technology internally, with a strong and solid structure that never deforms. 9. Water adding method: An automatic water adding system is adopted, which has the function of automatically replenishing the water level when the water level is insufficient, and the test is not interrupted. 10. Nozzle: Precision glass nozzle, salt spray testing machine used for 4000 hours to ensure no crystal blockage. 11. Protection system: Equipped with dual over temperature protection and insufficient water level warning to ensure safe use. 12. Temperature controller: digital display, PID control, high stability platinum temperature probe, error 0.3 13. Heating method: The laboratory adopts direct steam heating method, which increases the temperature quickly and shortens the standby time of the salt spray testing machine. 14. The spray tower is equipped with two conical dispersers, which have the functions of guiding fog, adjusting fog volume, and even fog falling. 15. The pressure bucket adopts Henry's law to heat and humidify, and provide the humidity required by the salt spray testing machine laboratory. 16. Opening method: Pneumatic automatic opening is adopted, The salt spray testing machine is one of the "three prevention" (humid heat, salt spray, mold) testing equipment for artificial climate environments. It is an important salt spray testing equipment for studying the adaptability and reliability of various environments in industries such as machinery, national defense, light industry, electronics, light industry electronics, and instruments. This salt spray testing machine can perform neutral salt spray tests in accordance with GB/T2423.17 "Basic Environmental Testing Regulations for Electronic and Electrical Products - Test Ka: Salt Spray Test Method", and can also perform acetate spray tests. This salt spray tester complies with CNS, ASTM, JIS and ISO standards. The salt spray test is to test the corrosion resistance of the products after coating, electroplating, Anodizing, anti-rust oil and other anti-corrosion treatments on the surfaces of various materials.
