Silicon Plates Suppliers and Manufacturers

The LCV series silicon cloth is a kind of cloth production which made based on fiberglass substrate through special processing. Because of its nice thermal conductivity, insulation and convenient assembly, it widely used in electronic appliances industry. When using, you should select different thickness of the thermal conductive silicon tape to cut according to the size of the fever interface and the height of the gap. Then putting the silicon tape in the gap between the fever interface and their components gap to play as a heat-conducting medium. Features & Benefits: Heat resistance, insulation, fire prevention, shock resistance Typical Applications: Heating power components Automobile electronic heating module Power module Household appliances Computer and peripherals, the filling and any place need heat dissipation between the heating element and the bottom plate.

LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-corona, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH UL. Typical Applications High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost. Applying Process 1.Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil. 2.Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural. 3.Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected. For more , please kindly feel free to contact rita(at)szutd.com

High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact rita(at)szutd.com

Silico manganese slag ferro manganese hc (hc femn) ferro silico manganese (fesimn) silicon carbide silico manganese baghouse dust ferro silicon ferro silicon dross calsifer 50 and calsifer 75.Producer

Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or  the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact rita(at)szutd.com

LCN is a kind of thermal conductive pad which do not contain silicone oil and do not volatilize and apply in optical instrument and those have sensitivity on silicone oil. There is silicone oil exuding from traditional thermal pad after heating, however, LCN absolutely solve this problem of silicone oil leakage. Whats more, the LCN series are especially fitting for filling no flat and high cumulative tolerance interface. Features & Benefits: No siloxane, no volatilization, no pollution Soft and low hardness material, good for filling High thermal conductive, low contact heat resistance Electric insulator Typical Applications: The products you are afraid of being polluted by silicone oil Optical precision equipment Laptop and projector Mobile and communication equipment, high speed large storage driver Heat pipe assembly, control equipment of car engine Telecommunication hardware and equipment High-end industrial control, and medical electronic area

The material is heat reinforced polymer, designed to meet the Thermal conductivity and reliability demand for the thermal conductivity of high application terminal. In addition, the heat sinks performance benefits a lot from the low heat resistance. And improve the microprocessor, DC - DC converter of memory module and the reliability of power module. The phase change characteristics: the material is solid in room temperature and installation is completely convenient, used between heatsink and devices. The material can be softened and flowing when the products reach phase-change temperature to fill the devices tiny irregular contact surface. Thus, the material has the ability to fill the gap between the devices and heat sink completely, make the phase change better than non-current elastomers or thermal graphite pad and get the performance of thermal conductive silicon grease. The material is nonconductive, however, as the material has endured the phase change at high temperature, may make the metal get to the metal, so the phase change interface material cannot Features & Benefits: Low heat resistance and low stress Natural sticky, easy to use-no need to use glue No radiator preheating Flow but not silicon oil Low volatility--less than 1%

Foil Thickness: 0.05-0.5 mm; Width:300-500 mm, Sheet Thickness: 0.6-30 mm; width:1500-2000 mm. Grade 1, 2, 4, 5, and 7. Submit LOI / RFQ along with KYC/CIS. one full service of the shipments, we are available provide FOB, CIF, DDU and DAP.

Stainless steel base plates, Kaftans, Indian ladies wear.

Silicon carbide raw materials and resources including silicon carbide sand and powder, as well as silicon carbide products. different qualities of silicon carbide are available for sale including sic98, sic90, and sic75..

Looking for a buyer. We have a large quantity of certified aluminum plate ranging from 3/4 of an inch up to 8 inches in thickness various sizes.

Synonym: Silica Sand, Quartz Sand, SiO2 Color: Rose Weight: 1-Ton, 100-lb, 50-lb, 5-lb, 1-lb, 8-oz, 4-oz, 1-oz Features: Industrial Sand, Low Cut (higher color) Loading Level (%): Varies, typically 40-60. Uses/applications: Aquaculture, Agriculture, Apothecary, Ceramics, Dental Laboratory Technicians, Hobbyists, Hydrothermal Technologies, Jewelers, Lapidaries, Machinists, Medical, Metal Workers, Manufacturers, 3D Printing, Abrasives, Aggregates, Automobile, Cement, Ceramic, Chemical, Detergents, Electronics, Industrial, Feeds, Filters, Dynamite / Fireworks, Glass, Hydroponics, Oil and Gas, Paint, Pesticides, Plastics, Rubber, Sealants, Solar Panel, Salt-water-pool-delivered, Veterinarian, Model Makers, Optical, Painters, Woodcrafters Brand: American Tripoli Condition: New Shipping: Standard Shipping (USPS First Class�®) Loading Level (%): Varies, typically 40-60. Technical Data: Cilas Particle Size Distribution: Mesh R-30 65 0.00 100 0.00 150 0.00 200 Trace 325 .035 400 .113 -400 99.851 99.9% Less than 50 micron 95% Less than 20 micron Chemical Analysis: (typical values) SiO2 94.03 TiO2 0.08 Al2O3 2.34 Fe2O3 0.83 FeO 0.03 MnO 0.01 MgO 0.23 CaO 0.89 Na2O 0.03 K2O 0.16 P2O5 0.01 CO2 0.03 Unreported 1.33 Loss on ignition 1.85 Ph 5.3-6.0 Fusion point (degrees C) 1640 Bulk density (lb/cu. Ft) 41 Oil absorption (g/100g) 45 Specific Gravity 2.55 Buy direct from the manufacturer, with no middleman. Manufactured and distributed by American Tripoli, Seneca, Missouri 64865 - U.S.A. Depending on the quantity (weight) purchased, each purchase includes: (1) purchased weight of the product (1) appropriate weight bag (1) Wooden Pallet (for 100lb & 1Ton) (1) Stretch Wrap double wrapped (for 100lb & 1Ton)

There is a layer of oxidized film on the surface of titanium plate GR7, which is equivalent to a good long-term wear-resistant hair separating agent. The use of titanium plate saves the separating agent, makes the plate peeling easily, and eliminates the pre-treatment process. The plate is half lighter than the copper board. The service life of titanium plate is more than 3 times that of copper plate, which can reach 10 to 20 years according to operating conditions. The titanium plate GR7 can increase production capacity and reduce the production cost of electrolytic copper, so that it has better economic benefits. Grade 5 titanium alloy also known as Ti6Al4V, Ti-6Al-4V or Ti 6-4titanium alloy, is the most commonly used alloy. It has excellent specific strength, excellent corrosion resistance and fracture toughness, as well as good weldability and ability to withstand extreme temperatures, and can be strengthened by heat treatment. The alloy was originally developed for the aerospace market and is widely used in aerospace structural components. Because of its very good biocompatibility, it is also widely recognized in the medical industry. Typical applications include aero-engine components, fuselage components, marine equipment, offshore oil and gas equipment, power generation, chemical industry, automotive moving parts, medical equipment, surgical implants, sports equipment. Titanium Sheet Grade 5 has excellent corrosion resistance, small density, high specific strength and good toughness and weldability. It has been successfully applied in aerospace, petrochemical, shipbuilding, automotive, pharmaceutical and other sectors. We also have ti6al4v eli and ti6al4v. https://www.yunchtitanium.com/titanium-sheet-1