Hebei yida anti impact rebar coupling system is a mechanical rebar splicing system, be made of high quality alloy steel. It has already passed the high speed tensile test of anti instant impact by germany berlin bam laboratory. It has been widely applied at the sites where required high level of resistance to impact. The coupler sleeve will be perfect connected with rebar by cold swaged deformation in the application, and dual couplers will be connected by a high strength bolt.Its size can be from 12mm into 40mm different diameter bars. Special advantages: (1)each rebar is connected by cold swaged with a coupling, it was processed by large-tonnage hydraulic machine and unique split mould to ensure high quality and reliable radial deformation swage. (2)rebar sleeve bond press is done prior to site connection saving precious site time. (3)the two sleeves are connected through a high-strength bolt, quality ensured. (4)installation on site is easy and fast, even in dense cages. No x-ray check is needed and installation can be done in any weather conditions. (5)no thread cutting, no need heat or pre-heat on rebar, hence the rebar retains its original characteristics after splice. (6)the yida acj rebar coupling system stands complex or full tension as well as full compression state. Application guide: Proper installation is very important to ensure the design load will be reached in the application. Yida strongly recommends that the installation and site quality check be done according to the required guidelines and dimensions. Site installation method Step 1:screw the bolt into female coupler swaged with rebar, till unable to screw continually. Step 2:screw another side of bolt into the other sleeve after swaged with rebar, till unable to screw continually. Step 3:with help of two pipe wrench, tighten the connection by turning both rebar / couplers in opposite direction at the same time. -
Advantages: Bar-break feature guarantees fully ductile elongation. No reduction of the bar cross-section area. Material of the rebar coupler is No.45 steel. Working principle: 1.First,We use GQ50 rebar cutting machine to splice up the end of rebar. 2.Secondly,we use Upset Forging Parallel Thread Machine (BDC-Auto1 Machine) to forge the end of rebar. 3.Third, we use Parallel Thread Cutting Machine (LW-I500 Machine) to thread the ends of the rebar which have been forged. 4.Fourth,an upsetting coupler is used to link the two ends of rebar in parallel thread.
Product parameter: The GL-12 Rebar Material Organizer & feeder Machine is widely cooperated with rebar automatic cutting,rebar upset forging,rebar thread cutting as well as thread rolling procedure,saves labor force and higher working efficiency in construction rebar mechanical splice technology .Its product design is compact,flexible and effective; and the unit size is 4m*3m*1.5m, which realizes the decomposition of the whole bundle of 16-40 rebars, the lateral displacement of the single rebar, the longitudinal fast forward, feeding and fast backward in work area and the second lateral displacement to the reservior. Use the Siemens frequency converter to regulate the moving speed. The cylinder controls the inverting and feeding of the material. The feeding speed is 0.5m/s. Product features: 1.The equipment is very flexible to use and with widely scope application. The bottom bracket of GL-12 Rebar Material Organizer & Feeder Machine is detachable and equipped with adjustable anchor feet, which can adapt to different height of equipments application. The equipment adopts the design of application expansion and it is easy to combine and lengthen. It can adapt to rebars of varying length and various processing equipments as well as flexibly transmitting the rebar. The rebar material organizer is widely used in construction, expressway, nuclear power plant and other industries and applies to organizing and conveying the rebars of various specification and varying length. Well-designed and efficient and durable We adopt the well-known brand motor and gear reducer to ensure product's durability. Use Siemens frequency converter to regulate the moving speed can effectively reduce the assistant machining time. The well-known brand large diameter cylinder to invert and feed is stable and durable. The specially designed turnover fixture is efficient and safe. The soft chain type collecting rack is well-adapted and capacious, and does little harm to rebar. Simple maintenance can ensure the normal operation as the simplified design can adapt to complicated processing environment, for which the purchase and use cost is low. Working Principle: Step1. Prepare rebars and use the crane to sling them on the shelf. Decompose the whole bundle of bars then can make the single ones lateral displacement. Step 2.Remove the single rebar to the working area by reversing device. The rebar can realize the the longitudinal fast forward, feeding and fast backward in this area. Step 3.Carry the rebar to the reservior through the second lateral displacement after processing and realize the storage function of rebar.
Application Guide: Proper installation is very important to ensure the design load will be reached in the application. Yida strongly recommends that the installation and site quality check be done according to the required guidelines and dimensions. Site installation method Step 1:Screw the bolt into female coupler swaged with rebar, till unable to screw continually. Step 2:Screw another side of bolt into the other sleeve after swaged with rebar, till unable to screw continually. Step 3:With help of two pipe wrench, tighten the connection by turning both rebar / couplers in opposite direction at the same time.
Ydzts-40c rebar taper thread cutting machine is designed and manufactured by hebei yida reinforcing bar connecting technology co., ltd. It is mainly used as a special equipment to make taper thread on the end of the rebar in the processing of rebar connection. Its applicable diameter is from 16 to40. It applies to grade and level rebar. It has reasonable structure, light and flexible, simple operation, high production efficiency. It is widely used in steel bar end processing of taper thread joints in concrete works .It adapts to a variety of complex construction site environment. The main performance parameters: Processing of bar diameter range: 16mm 40mm Processing thread length: less than or equal to 90mm Processing steel length: greater than or equal to 300mm Power: 380v 50hz Main motor power: 4kw Reduction ratio reducer: 1:35 Rolling head speed: 41r/min Overall dimensions: 1000 480 1000 (mm) Total weight: 510kg
PARAMETER: 1. Range of application: Ï?16-Ï?40 2. Threading speed: 32r/min 3. Back off speed: 64r/min 4. Pitch size: 4 sizes 5. Electric motor power: 2.4 KW /3 6. Rolling (cut) head moving distance: 150mm 7. Out dimension: 1325*570*1070mm Principle:
Specifications: Steel bar connection 1.Material:carbon steel 2.Easy operation 3.Saving time& rebar material 4.No.45 steel Specifications Steel bar connection 1.Material:carbon steel 2.Easy operation 3.Saving time& rebar material 4.No.45 steel Spec.: 1. Sleeve material: #45 high quality carbon steel 2. Diameter :14~40mm (enough quantity in stock) 3. Carbon sleeve thread pitch:1.75/2.5/3/4 4. Sleeve standard thread angel: 60/75 5. Steel bar sleeve is used to connect two pieces of rebar together. 6. Passed the tensile strength test, the tensile strength is 594mpa, test report canbe supplied as well. 7. The steel bar connecting sleeve has passed iso9001 international quality system, so quality can be guaranteed with no doubt. 8. Types: standard type / left-handed and right-hand type/ reducing type sleeve. 9. We are well-known enterprise in bar connecting field in china. 10.Different spec.Is available as per your requirements, free sample can be supplied for your reference.
Led bulb, tube light, panel light, decoration light, wall light, steel wires, steel plate, stainless steel plate, twisted wire rods, galvanized wires, wire mesh, site fencing, mosquito mesh, thread rods, rebar, twisted rods, t bar, nuts and bolts, hardware, pvc pipes, upvc pipes, api pipes, melamine, mdf board, plywood, film faced, shuttering, packing, core veneer, face veneer, hdf molded door skin, door filler, tubular particle boards, pvc boards, wpc boards, doors, block board, hard board, gypsum board, canopy, carpet, flooring wooden, bamboo, laminated engineering, tiles, granite tiles, granite blocks, black galaxy, wash basin, water closets, washbasins, ss sinks, faucets, furniture, pvc edge bending, crew, locks, pvc seals, silicone cartridges, shower enclosures, shower door hinges, handles, knobs, brackets, slides, nails, solar panels, flexible solar panels, solar power station, battery, inverters, rechargeable fans, lights, spring, 3ply disposable face mask, oxygen concentrator ,.Buying office, oem, components sourcing, value added services
Hebei Yida BTS-3 Rebar Parallel Thread Cutting Machine is used for thread cutting on the end of rebar after cold forging. Processing different diameter rebar, only chaser need to be changed, so it's very easy and simple for working man.
China iron rebar stirrup bending machine manufacturer China zhihaomachinery is a leading China iron Rebar Stirrup Bender manufacturer, reliable supplier and exporter. Adhering to the pursuit of perfect quality of products, so that our iron Rebar Stirrup Bender have been satisfied by many customers. Extreme design, quality raw materials, high performance and competitive price are what every customer wants, and that's also what we can offer you. Of course, also essential is our perfect after-sales service. If you are interested in our iron Rebar Stirrup Bender services, you can consult us now, we will reply to you in time!
construction automatic rebar bending machine Technical parameter: Model KT6 double bending way Single wire 5-16mm Double wire 5-12mm Max bending angle ±180 Max traction speed 75m/min Max bending speed 800 /sec Dimension 4000*2000*2200mm Machine color Yellow (customized) Total power 52.5kw(include air compressor) Work temperature -5 --40 Length accuracy ±1mm Angle accuracy ±1 Average power 12kw/h Weight 3000kg Optional with long platform
RC-20 Portable Rebar Cutting Machine is of light weight, small size, easy to carry, easy to operate, cutting process does not produce sparks, dust, no odor. Mainly used to cut steel bars used in construction, such as rebar. Round. Steel bars. Screws, etc. Voltage 220V/110V Wattage 830W/900W Gross weight 17.5kg Machine weight 13kg Cutting speed 3.0-3.5 s Max rebar 20MM Min rebar 4MM Package One Pc /Metal Box/Cardboard Ctn Carton Size 460*160*270mm Machine Size 410*115*220mm Certificate CE ROHS
Model GW50B 1. Bending round steel diameter 6-50mm 2.Grade thread screw steel diameter 6-42mm 3. Working plate diameter spec 320mm 4. Main shaft speed 8-15r/min 5. Motor spec 4KW/380V 6. Motor speed 1440t/min 7. Dimension 1060, 850, 730mm 8. Net weight/Gross weight 360kgs/380kgs 9. packing size 1100, 900, 900mm
Bending diameter o steel bar of round steel Round bar:6-50mm III class reinforced bar :6-42mm Speed of working disc 10r/mm Motor power 4KW Diameter of working disc 400mm
Place of Origin: Shandong China (Mainland) Brand Name: zhongyun Model Number: RC-16 Type: REBAR BENDER Voltage: 220/110V Wattage: 800/900W Bending speed: 5.0 s Max.diameter: 16mm Min.diameter: 4mm Gross weight: 16.5kg Machine weight: 15kg Certificate CE ROHS
Name: Portable Electric Hydraulic Rebar Bender Type: NRB-32 Voltage: 220V Wattage: 1350W Gross weight: 32KG Net weight: 24KG Bending speed: 5.0-8.0S Max.rebar: 32MM Min.rebar: 4MM Carton size: 760*290*220MM Machine size: 560*260*200MM Bend angle: 0-130 Package: One Pc /Metal Box/Cardboard Ctn Certificate: CE ROHS
Model No. ZM-22 ZM-40 ZM-50 Max Tying Diameter 21mm 40mm 50mm Time of Making a Knot 0.8 seconds 0.8 seconds 1.0 seconds Voltage DC9.6V DC9.6V DC9.6V Weight 2.15kgs 2.2kgs 2.25KGS Turns per Tie 2 turns/3turns 2turns/3turns 3turns/4turns Ties per Coil Approx. 260ties(2turns) Approx.160ties(2turns) Approx. 100 ties(3 turns) Ties per Charge 4-5 Coils 6-7 Coils 7-8 Coils -
Model KW0041 Applicable rebar Sizes 8-68mm Wire Diameter 1.5mm Time of Making a knot 1.2 seconds Voltage DC9.6V Weight 3.3kgs Turns per tie 1turn Ties per coil Approx 140ties/1 turn Ties per charge 5coils/700 ties Wire Length Per Coil 28m Length of Wire for Tying 100-220mm/1turn Machine Size(L*W*H)(mm) 330mm*310mm*80mm -
FEATURE: 1 Max. Tying Knots: more than1200knots on a single charge 2 Typing time: 0.8second/knot 3 The number of the knot can be select to be 2 turns or 3 turns 4 Packing precast concrete products 5 Precast steel or mental tubing packing in architecture engineering scen 6 Rebar tying machine Widely used in construction industry 7 Rebar tying machine ( KP-400A ) conforms to 89/336/EEC Electromagnetism Compatible, 73/23/EEC Low Voltage and 98/37/EC Machinery Requirement of ECC Instruction. 8 Rebar tying machine (KP-400A) is hand-held machine used to pack rebars quickly. 9 Automatic rebar tying machine by iwiss made is a miniature motor tool possesses the trait of safety and credibility. Rebar Tying Machine Model KP-400A Exerior size(mm) 290Ã?100Ã?277 Machine weight(Kg) 2.1 Motor voltage(v) 9.6 Max tying diameter(mm) 40 -
Model: RTM-21 Tying Diameter: 21mm Time Of Making A Knot: 0.8 Seconds Voltage: DC9.6V Weight: 2.15kg Turns Per Tie: 2 Turns/ 3 Turns Ties Per Coil: Approx. 260 Ties(2 Turns) Ties Per Charge: 4-5 Coils Length Of Wire For Tying: 380mm/2 Turns ( 510mm/3 Turns ) Dimension(L)X(W)X(H): 268X100X296mm -
