No. Type Nano acrylic Interior Wall Primer (Water Thinnable) is an economy water-based primer that enhances the application and finish of interior topcoats. 1 FEATURES Nano Acrylic Cement Primer is water based, Economical interior primer with good whiteness,good coverage and flow and leveling properties. 2 RECOMMENDED APPLICATION Nano Acrylic interior wall primer that can be suitable for priming plastered wall,asbestose,cement concrete etc. PRODUCT TECHNICAL DATA No COLOURS White 1. FINISH Smooth and matt 2. COVERAGE 1 coat: 90-100 sq.ft/ltr 2 coats: 60-70 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS NA 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized. Recommended Use :- It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected Industrial shades FINISH : Matt SOLIDS BY VOLUME : 63 + 3% THEORETICAL SPREADING RATE : 8.4 sq.mt / lt at a recommended DFT of 75 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 30C & 65% Relative Humidity) : HARD DRY : 16 - 18 hours FULL CURE : 7 days SHELF LIFE : Base: 6 months Hardener: 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation ) POT LIFE : 2 hours at 30�°C APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 �µ. OVERCOATING INTERVAL : MIN : 8 hrs. MAX : 24 hours (In case it is exceeded, the surface should be roughened byemery scuffing) OVERCOATABILITY : Epoxy, PU, Chlorinated Rubber and Synthetic Enamel intermediate &finish coat.
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 �± 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 �µ FLASH POINT : Base : Above 25�°C Hardener : Above 25�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO Base : Hardener ( As per our recommendations) : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Airless Spray POT LIFE : 2 - 3 hours min at 30�° C RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU
ULTRA PREMIUM weatherproof interior and exterior emulsion is a smooth, water-based, modified acrylic, interior and exterior wall finish with silicon additives. FEATURES :- ULTRA PREMIUM weatherproof interior and exterior emulsion is specially formulated to withstand extreme tropical conditions of rainfall, humidity and heat ULTRA PREMIUM provides excellent resistance from growth of algae and fungi on the walls. This prevents appearance of black spots due to algal growth. ULTRA PREMIUM provides extremely good protection against alkali and UV degradation, thus ensuring that the shade doesnâ??t fade for a long time and the paint lasts longer. RECOMMENDED USE :- ULTRA PREMIUM Acrylic interior and exterior emulsion is interior and exterior wall finish that can be applied on all type of smooth plaster, asbestos sheets, concrete etc. PRODUCT TECHNICAL DATA :- COLOURS : White & other shades FINISH : Smooth and soft sheen COVERAGE : On smooth primer masonry surface by brushing 1 coat: 140-170 sq. ft/ltr 2 coats: 85-95 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc) DRYING TIME : Surface drying time â?? 30 minutes GLOSS LEVELS/SHEEN LEVELS : Silky smooth with soft sheen FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable SUITABILITY OF THINNER PAINT Use within 24 hrs. SHELF LIFE 18 month from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat. PERFORMANCE DATA :- ABRASION RESISTANCE : Excellent WATER RESISTANCE : Excellent REMARKS : 1) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. 2) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. 3) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. 4) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling the paint-this is required for all paints. 5) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. 6) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. 7) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. 8) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is recommended as primer on M.S surface for OEM's as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT :- Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS :- SURFACE DRY : 60 to 90 minutes (At 30�°C & 65% Relative Humidity) :- HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE :- BASE : 6 months HARDENER : 6 months SURFACE PREPARATION Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray / By Airless Spray THINNER :- Epoxy Thinner 190 POT LIFE :- 4 hours min at 30�°C RECOMMENDED DFT :- 30 - 40 �µ. OVERCOATING INTERVAL :- MIN : 8 Hours MAX : 24 Hours COMPATIBILITY :- Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. . Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application:- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 1.4 mm Nozzle Pressure : 40 - 70 p.s.i. For Airless Spray Application:- Thinner : Epoxy Thinner 190 Addition : Max 5% Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
ShoHan Intensive Care Body Lotion delivers luxurious moisturization for decadently pampered skin all day long. The moisturizing body lotion for dry skin is crafted with Cocoa Butter, Shea Butter and Olive Oil extract to soften, hydrate and pamper for radiant, healthy-looking skin and 48 hour moisture. Lightweight, fast absorbing, non-greasy body lotion that's ideal for use on the entire body. Immediately boosts skin hydration and continues to strengthen skin moisture barrier throughout the day. The hypoallergenic, non-comedogenic formula is free of fragrances, parabens and sulfates, recommended by all dermatologists for Sensitive Skin. We use only the finest natural, raw ingredients for soft, hydrated and beautiful hair & skin. We support sustainable production of Shea & Cocoa Butter and Coconut Oil. You can feel good about what you put on your hair and skin Great for all skin types and your entire family 100% Vegan and Cruelty Free Product. GMP certified, ISO and Halal certified product. Available in 3 variants COCOA BUTTER SHEA BUTTER OLIVE OIL ShoHan Intensive Care Body Lotion has the following features Natural Ingredients â?? Natures most trusted ingredients used to be applied on your skin and body. Paraben Free -No harmful preservatives added to increase the shelf life of the product making it completely safe product. Phthalate Free -No harmful phthalates used, ensuring a safe product. Cruelty Free- Not tested on animals, making the product cruelty free. Mineral Oil Free -No mineral or synthetic oil added, which make skin rough and dry and causes skin problems. Sulfate Free - No skin damage, as no sulphates added. All Skin Types â?? Unique formulae, that blends and can be used for all skin types. Dermo Tested â?? Derma tested product proving its benefits. Hypo Allergenic- All pure ingredients used to not likely cause an allergic reaction when used. With The Essence Of Olive Oil Extracts â??Rich in omega-3 fatty acids and antioxidants, olive oil reduces wrinkles, protects against UV, and helps sooth the skin. With The Essence Of Cocoa Butter Extracts â?? Best known for its anti-inflammatory properties, heals cuts and scrapes, helps fight breakouts and boosts skin moisture. With The Essence Of Shea Butter Extracts - Rich in fatty acids, helps in keeping skin hydrated for the maximum time. Creates a barrier that holds moisture and prevents your skin from drying.
ShoHan Intensive Care Body Lotion delivers luxurious moisturization for decadently pampered skin all day long. The moisturizing body lotion for dry skin is crafted with Cocoa Butter, Shea Butter and Olive Oil extract to soften, hydrate and pamper for radiant, healthy-looking skin and 48 hour moisture. Lightweight, fast absorbing, non-greasy body lotion that's ideal for use on the entire body. Immediately boosts skin hydration and continues to strengthen skin moisture barrier throughout the day. The hypoallergenic, non-comedogenic formula is free of fragrances, parabens and sulfates, recommended by all dermatologists for Sensitive Skin. We use only the finest natural, raw ingredients for soft, hydrated and beautiful hair & skin. We support sustainable production of Shea & Cocoa Butter and Coconut Oil. You can feel good about what you put on your hair and skin Great for all skin types and your entire family 100% Vegan and Cruelty Free Product. GMP certified, ISO and Halal certified product. Available in 3 variants COCOA BUTTER SHEA BUTTER OLIVE OIL ShoHan Intensive Care Body Lotion has the following features Natural Ingredient Natures most trusted ingredients used to be applied on your skin and body. Paraben Free -No harmful preservatives added to increase the shelf life of the product making it completely safe product. Phthalate Free -No harmful phthalates used, ensuring a safe product. â?¢ Cruelty Free- Not tested on animals, making the product cruelty free. â?¢ Mineral Oil Free -No mineral or synthetic oil added, which make skin rough and dry and causes skin problems. â?¢ Sulfate Free - No skin damage, as no sulphates added. All Skin Types â?? Unique formulae, that blends and can be used for all skin types. â?¢ With The Essence Of Olive Oil Extracts â??Rich in omega-3 fatty acids and antioxidants, olive oil reduces wrinkles, protects against UV, and helps sooth the skin. With The Essence Of Cocoa Butter Extracts â?? Best known for its anti-inflammatory properties, heals cuts and scrapes, helps fight breakouts and boosts skin moisture. With The Essence Of Shea Butter Extracts - Rich in fatty acids, helps in keeping skin hydrated for the maximum time. Creates a barrier that holds moisture and prevents your skin from drying.
ShoHan Hair Vitalizing Serum is an extraordinary oil serum that is infused with Argan oil Olive oil and Almond Oils that deeply conditions your hair and restores moisture Controls frizz and revives dry and damaged strands making them shiny and nourished Adds 6X more shine provides deep nourishment and removes up to 98 frizz to completely transform dry hair into lustrous soft and bouncy hairSpecial formulae that restores the hair elasticity and nourishes the hair and protects hair against UV rays and heat damage enhances the colour of coloured hair Controls hair fall and repairs damaged hair and prevents further damage and breakage Contains no mineral oil or synthetic oil which make hair rough and dry and causes skinscalp problems 100 Vegan and Cruelty Free Product GMP certified ISO and Halal certified product ShoHan Hair Vitalizing Serum has the following features Deeply Conditions Hair With combination of 3 natural oils ensures deep conditioning stronger hair Restores Moisture Balance Hydrates and moisturizes hair making them lively and bouncy again Controls Frizz Hydrates and moisturizes hair and revives dry and damaged strands making them shiny and nourished Removes Split Ends Helps seal split ends avoiding unnecessary haircuts leading to longer and stronger hair No Phthalates No harmful phthalates used ensuring a safe product Even Smooth Shiny Hair Adds 6X more shine provides deep nourishment and removes up to 98 frizz to completely transform dry hair into lustrous soft and bouncy hair Restores Hair Elasticity Special formulae that restores the hair elasticity and nourishes the hair Protects Repairs HairProtects hair against UV rays and heat damage enhances the colour of coloured hair Detangles Hair Controls hair fall and repairs damaged hair and prevents further damage and breakage With The Essence of Olive Oil Extracts Rich in omega3 fatty acids and antioxidants olive oil helps in thicker and stronger hair With The Essence Of Almond Oil Extracts Rich in essential fatty acids that helps in moisturizing the scalp and strands leading to smooth hair and soft texture With The Essence Of Argan Oil Extracts Rich in antioxidants vitamin E and essential fatty acids that helps fight dandruff frizz adds shine and keeps hair protected from damage No Sulphates No hair damage as no sulphates added No Parabens No harmful preservatives added to increase the shelf life of the product making it completely safe product No Mineral Oil No Mineral or synthetic oil added which make hair rough and dry and causes skinscalp problems Skin Safe Fused with Natural Virgin Oils making it skin friendly and skin safe
Diacetyl Tartaric Acid Esters of Mono  and Diglycerides Characters: Ivory or straw yellow powder or granular solid which is easily soluble in hot water. It is a non-ionic emulsifier with HLB value of 8-10. Applications: It can produce strong effects such as emulsification, dispersing and aging resistance, so it can be used as good emulsifier and dispersant. (1) It can increase the springiness, toughness and gas-holding capability of dough effectively, reduce its softening degree, increase volume of bread and steam bread, and improve their organization and structure. (2) It can react with amylose to delay and prevent the food aging. (3) It can be used in cream to make it smoother and finer. (4) It can be used in butter and concentrated butter to prevent oil separating and enhance its stability. (5) It can also be sued in sugar, syrup and spices. (6) It can be used in non-dairy creamer to make the emulsion homogeneous , stable and supple in mouth. Usage: (1) Put this product in warm water at about 60�?? to get paste shaped substance, and then use it in appropriate proportion. (2) Dissolve this product in oils or fats homogeneously before further processing. (3) Directly mix it with flour for use. Recommended Addition Amount: Addition maximum is 1.0% for raw dried flour products and raw wet products, while 5.0% for non-dairy creamers. The addition amount can be changed based on production need for cream and fermented milk. Technical Index (Conform to GB25539-2010 standard Acid value (Calculated by KOH) / (mg/g) 65-85 Saponification value (Calculated by KOH) / (mg/g) 390-450 Total tartaric acid(W/%) 10-40 Total glycerol(W/%) 11-28 Total acetic (W/%) 8-32 Free glycerol(W/%) �?�2.0 Ignition residue (W/%) �?�0.5 Pb/(mg/kg) �?�2 Packaging�? Aluminized bag vacuum packing with nitrogen inside. Net weight:20KG/CTN(5 KG *4) Storage & Transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and trasporting with materials that is explorsive, combustible or deleterious. The shelf life is 12 months.
Sodium Stearoyl Lactylate(SSL) Characters: Ivory powder or flake-shaped solid. It can be dispersed well in hot water and soluble in ethanol and hot oils and fats with pleasant caramel-like odor. It is an anionic emulsifier with HLB value of 8.3. Applications: It can be used for multiple purposes su ch as emulsification, aging resistance, gluten fortifying and fresh-keeping in many kinds of food such as bread, steam bread, noodle, instant noodle and dumpling. It can also be used as an emulsifier in milk, non-dairy creamer, margarine, fresh cream, meat products, animal and vegetable oils, etc. (1) Increase the springiness, toughness and gas-holding capability of dough, increase volume of the bread and steam bread and improve the organization and structure. (2) It can react with amylose to delay and prevent the food aging. (3) It can make it easier to remove biscuits from moulds to produce smooth appearance, distinct layers and crisp feeling in mouth. (4) It can make hot and spicy food more pliable and softer and prolong the preservation time. (5) It can produce smoother surface, lower broken ratio, higher soaking and boiling resistance for noodle, dried noodle and instant noodle, and make them chewier. (6) Enhance the quality of quick frozen food, improve their organization and structure, and prevent surface cracking and filling escaping. Usage: (1) It can be directly mixed well with flour for use� (2) Put this product into warm water at about 60 with proportion of 1:6 to get paste shaped substance, ten add it into flour in proportion to obtain better effect. (3) When used in non-dairy creamer or this kind of substance, it should be heated well with emulsified substance to get homogeneous emulsion before further processing. Recommended Adding Amount: 0.2~0.5 %( Calculated by Flour, Refer to GB2760-2011) Technical Index Acid value(Calculated by KOH) / (mg/g)60- 80 Ester value (Calculated by KOH) / (mg/g)120- 190 Total lactic acid (W/%)23.0-40.0 Sodium content(W/ %3.5- 5.0 Pb(mg/kg)2 Packaging Aluminized bag vacuum packing with nitrogen inside. Net weight:20KG/CTN(5KG *4) or packaged with moisture proof paper bag, 25kg/bag.. Storage & Transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and trasporting with materials that is explorsive, combustible or deleterious. The shelf life is 12 months.
Calcium Stearoyl Lactylate(CSL) Characters: Ivory powder or flake-shaped solid. It can be dispersed well in hot water and soluble in ethanol and hot oils and fats with pleasant caramel-like odor. It is an anionic emulsifier with HLB value of 5.1. Applications: It can be used for multiple purposes such as emulsification, aging resistance, gluten fortifying and fresh-keeping in many kinds of food such as bread, steam bread, noodle, instant noodle and dumpling. It can also be used as an emulsifier in milk, non-dairy creamer, margarine, fresh cream, meat products, animal and vegetable oils, etc. (1) Increase the springiness, toughness and gas-holding capability of dough, increase volume of the bread and steam bread and improve the organization and stru cture. It can react with amylose to delay and prevent the food aging. It can make it easier to remove biscuits from moulds to produce smooth appearance, distinct layers and crisp feeling in mouth. (2) It can make hot and spicy food more pliable and softer and prolong the preservation time. (6) Enhance the quality of quick frozen food, improve their organization and structure, and prevent surface cracking and filling escaping. Usage: (1) It can be directly mixed well with flour for use. (2) Put this product into warm water at about 60 with proportion of 1:6 to get paste shaped substance, ten add it into flour in proportion to obtain better effect. (3) When used in non-dairy creamer or this kind of substance, it should be heated well with emulsified substance to get homogeneous emulsion before further processing. Recommended Adding Amount: 0.2~0.5 %( Calculated by Flour, Refer to GB2760-2011) Technical Index Acid value (Calculated by KOH) / (mg/g)50- 86 Ester value(Calculated by KOH) / (mg/g)125- 164 Total lactic acid (W/%)32.0- 38.0 Calcium content (W/%)4.2- 5.2 Pb / mg/kg 2 Packaging Aluminized bag vacuum packing with nitrogen inside. Net weight:20KG/CTN(5KG *4) or packaged with moisture proof paper bag, 25kg/bag.. Storage & Transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and trasporting with materials that is explorsive, combustible or deleterious. The shelf life is 12 months.
Sealing against heat Especially in food packaging industry, this film can resist moisture for longer periods of time than any other possible film. These films can also resist high temperatures and extreme pressures. Some of the chemicals that OCA is usually used for are water-soluble adhesives, solvents, oils and acrylics. OCA is mostly used for bonding and sealing purposes. Long shelf life When using OCA you donâ??t have to worry about changing your adhesive films frequently. You can easily use them for many years together without having to worry about their effectiveness. This property of OCA is used all over the world in several sectors. From automotive and construction to food packaging and medical devices industries, you name it and you have it! Better adhesive bond Itâ??s all about better bond especially when we talk about products with high friction and usage level. The OCA is very easy to use and has better adhesion properties. The film can also withstand extreme temperature variation, can handle pressure and is able to maintain its quality for a long time. No post flow problems It has no post flow limitations. It can be easily applied even on curved surfaces. It can also work well with polyethylene and vinyl and other related materials. Itâ??s clear that OCA doesnâ??t have any restriction for applying it on different objects. Better adhesive adhesion There are more than hundred unique OCA bonding agents which make it better than other possible adhesive media available in the market. Itâ??s also more durable than other known adhesive. It can resist heat, abrasion and chemical treatments. Its anti-stagnant quality allows the document to be used in any environment. Its anti-reflective property makes it work well with light and fluorescent. UV stabilization It also has the UV stabilization feature. It works well to safeguard documents from harmful ultraviolet rays. So, it will not be affected by UV rays. It can work with any type of document. Vibrant and bright white OCA is extensively used for signage and also used as labels in food products like dairy products, milk and juice, etc. They are applied in outdoor and indoor environments as well. The vibrant and bright white color make it easy to recognize and read. It has excellent scratch resistance. It is water, heat and moisture resistant as well. The fact that it can be applied on smooth and flat surfaces makes it popular for use in food packaging and household items.
Brief description YJS-525 is medium hardness silicone with hardness Shore A 25. It is a kind of of two- component materials consisting of a flowable part A which when mixed with the curing agent or catalyst,cures at room temperature by a condensation recation. It is widely used for resin, gypsum, concrete/cement and artificial stone molding. Features -Easy to demould -Good resistance to tearing -Good elastic -Good tear&tensile strength -Dimensional stability in time ( deformation - shrinking only up to 0.3 % ) -Remarkable resistance to high temperatures (up to 200 - 220â?? ) -Final curing at room temperature Specification Typical general characteristics Inspection Method Value Product data (Catalyzed A+B) YJS-525 Hardness Shore A 25�±2 Mix Ratio A:B 100:2 Color / White Pot life 25 �°C (77F) 30-40mins Curing time 25 �°C (77F) 3-4 hours Mixed viscosity mPa.s 15000�±1000 Tear-strength kg/cm â?¥25 Tensile-strength M.pa â?¥4.2 Elongation % â?¥480 Shrinkage % â?¤0.3% Package * Small size:1kg/jar A +20gram/jar B, 12 jars in one carton. MAX 336KGS in one pallet 5kg/jar A + 100gram/jar B, 6 jars in one carton. MAX 750KGS in one pallet(metal drum) 5kg/jar A+ 100gram/jar B, 4 jars in one carton. MAX 480KGS in one pallet(plastic drum) * General size: 20kg/pail A +400gram/pail B, 18 pails or 24 pails or 27 pails in one pallet 25kg/pail A + 500gram/pail B, 18 pails or 24 pails or 27 pails in one pallet 200kg/pail A + 4kg/pail B, 2 pails or 4 pails in one pallet 1kg package 12 jars in one carton. MAX 336KGS in one pallet 5kg metal drum 6 jars in one carton. MAX 750KGS in one pallet(metal drum) 5kg plastic drum 4 jars in one carton. MAX 480KGS in one pallet 20kg or 25kg plastic drum 18 pails or 24 pails or 27 pails in one pallet 20kg or 25kg metal drums 18 pails or 24 pails or 27 pails in one pallet 200kg metal drum 2 drums or 4 drums in one pallet Storage YJS-525 has a shelf life of at least 12 months in the sealed container between 5 C and 30 C. If the material is kept beyond 12 months it is not necessarily unusable, but a test should be performed on the product to check suitability to the application
Product information Product name: OPTICALBRIGHTENER ER Liquid(PS-1. ER330) Color Index No: C.I.199 Synonyms: FBA 199; OBA 199,Fluorescent Brightener PS-1(ER330); Optical Brightener Agent PS-1(ER330) Molecular Structure: Molecular Formula: C24H16N2 Molecular Weight: 332.3972 CAS No: 13001-39-3 C.I. No.: C.I.199 Appearance: yellowish pulpy liquid E-value: 330 Features: Thisproduct is mainly used for whitening and brightening of blending fabrics suchas polyester and polyester cotton, polyester silk, polyester yarn, polyesterramie, polyester wool as well as whitening of chemical fiber and plastic. Thisproduct applies to pad dyeing and HTHP dip dyeing, especially low temperatureadsorption and high temperature setting process. Applications 1. Pad-dyeing hot melt method: Use quantity: 1.5-3g/L Process flow: two dip dyeing and two paddyeing (mangle expression 70) pre-drying (100) curing and setting (180 190, 40-30s). 2. HTHP dip dyeing method: Use quantity: 0.2 0.5% (o.w.f) Dyeing temperature: 120 130 Dyeing time: 30 - 60 minutes PH value: 4.5 - 5.5 (adjusted withacetic acid) Low temperature adsorption and hightemperature color development dyeing method: Use quantity: 0.5 1.0% (o.w.f) Dyeing temperature: 50 60 Dyeing time: 30 minutes PH value: 4.5 - 5.5 (adjusted withacetic acid) Process flow: add BC-100 whitening agentand additive (anhydrous sodium sulphate 1-2% relative weight of dyed cloth,acetone is adjusted in PH) and fabric to dye bath at room temperature temperature rises to 50, deying for 30min washing dehydration and pre-drying (100) setting and baking (180-190, 40-30s). Package & Storage: 25kg/50kg plastic drums. It can be packedin other forms according to user's requirements. Shelf life: not more than 12 months inthe room temperature. Cautions: 1.If suspension liquid is foundprecipitated and separated, just shake it before use, which does not affect theuse effect. 2.Please note that use this product within its yellow spot, i.e. paddyeing 5g/l,dip dyeing 0.8%(o.w.f). If use this product beyond its yellow spot, it will be easy to becomeyellow.
What is a vacuum fryer machine? The equipment uses heat conduction medium to dehydrate and dry food under negative pressure,the processed food has very low water content and oil content, crisp but not greasy.To some extent, it preserves the original shape, color, aroma and taste of fruits and vegetables completely, and is rich in vitamins, minerals, fiber and other nutrients. It has the characteristics of low sugar, low salt, low fat and low heat. Model:XSD-WX, XSD-30,XSD-60,XSD-120 Capacity:10-100KG per hour Working temperature:70â??-120â??(adjustable) deoiling method:inner deoiling under the vacuum state deoiling speed :0-300r/min(adjustable) Material :vacuum kettle,inside storage tank:stainless steel 304 outside of pot body storage area has insulation layer,material is stainless steel matte plate control system microcomputer automatic control(manual/automatic) Application 1.Fruits: Apple, Banana, Pineapple, Peach, Cranberry, etc. 2.Vegetables: Carrot, Pumpkin, Snap bean, Sweet potato, Taro, Potato, Garlic, Green Pepper, Onion, etc. 3.Nuts: cashew nut, Peanut, etc. 4.Seafood, meat etc. Fish, shrimp, shellfish,chicken etc 5.Cooked wheaten food fried dough twist,crust of cooked rice,caramel treats etc Our Advantages 1.Low temperature fried, healthy food and low cost.It can prevent the loss of nutrients in the food at high temperature,effectively maintain the natural color and flavor of the food, and reduce the processing cost than the ordinary frying method. 2.Low oil content,good taste and no greasy. The oil content rate of food is below 15%. 3.Well stored and concentrated, the food is crisp and delicious 4.Rapid water evaporation and short drying time. 5.Safe, reliable and easy to operate. 6.Famous brand components. Electrical parts and operating parts are made of world advanced brand components. 7.Good expansion effect and high product rehydration 8.Long product shelf life. � Shandong Qinglei Environmental Technology Co.,Ltd is an equipment manufacturer integrating design, production and assembly. Our products include heat exchangers, heat exchange units, pressure vessels, storage tanks, TCU temperature control systems, reactors, distillation towers, VOCS purification and recovery systems, vacuum� frying machine. If you need any of them,please donâ??t hesitate to let me know,I will reply you ASAP.
We take your Custom Wood Manufacturing from prototype to shelf We can highly customize your product with qualities unique to your company. From our custom wood products, we can take your product to completion because we are always a reliable part of your supply chain. Request a quote from one of our knowledgeable salespeople today. Custom Wood Manufacturing are found everywhere in consumer, commercial and industrial markets. They range from large building support to home decor, musical instruments and furniture. At All Win , we specialize in standard and custom wood products to meet our customers' needs for longevity, style and high quality. Our manufacturing facility produces a wide range of wood products and components to bring unique products to life. Our in-house experts examine the wood to find the right strength, density, grain and wood type for each project based on its design specifications and intended application. We then grind, process and finish the product from start to finish before delivering the finished product to the next step in your supply chain. Categories of Custom Wood Manufacturing Furniture. This category offers any wooden furniture of your choice: dining tables, coffee tables, sideboards, armchairs, sofas, beds, stools, children's furniture. You can configure your wooden furniture by wood type, colour, size, design and style: modern, art deco, high-tech, minimalist, loft, etc. Decorative style. Decorative and decorative woodwork is best suited to decorate rooms and create a cosy atmosphere. You can model them yourself and we can make them come true. We will create customised decorative items such as wooden interior paintings, wooden wall clocks, wooden framed mirrors and much more, to suit any room style from modern to classic. Colours, sizes, wood types and shapes: create unique products to suit your own projects. Accessories. Wooden clocks, organisers, stands, key fobs, laptop mini-tables, boxes - we will make all these home furnishings to your individual order so that you can live in comfort. If you want to print your own logo, initials, choice of material, product shape, then go ahead! Together with Allwin you can create all your fantasies in eco-wood product design.
Calcium Stearoyl Lactylate(CSL) Characters: Ivory powder or flake-shaped solid. It can be dispersed well in hot water and soluble in ethanol and hot oils and fats with pleasant caramel-like odor. It is an anionic emulsifier with HLB value of 5.1. Applications: It can be used for multiple purposes such as emulsification, aging resistance, gluten fortifying and fresh-keeping in many kinds of food such as bread, steam bread, noodle, instant noodle and dumpling. It can also be used as an emulsifier in milk, non-dairy creamer, margarine, fresh cream, meat products, animal and vegetable oils, etc. (1) Increase the springiness, toughness and gas-holding capability of dough, increase volume of the bread and steam bread and improve the organization and structure. It can react with amylose to delay and prevent the food aging. It can make it easier to remove biscuits from moulds to produce smooth appearance, distinct layers and crisp feeling in mouth. (2) It can make hot and spicy food more pliable and softer and prolong the preservation time. (6) Enhance the quality of quick frozen food, improve their organization and structure, and prevent surface cracking and filling escaping. Usage: (1) It can be directly mixed well with flour for use.�?�¯ï¿½?�¿ï¿½?�½ (2) Put this product into warm water at about 60 with proportion of 1:6 to get paste shaped substance, ten add it into flour in proportion to obtain better effect. (3) When used in non-dairy creamer or this kind of substance, it should be heated well with emulsified substance to get homogeneous emulsion before further processing. Recommended Adding Amount: 0.2~0.5 %( Calculated by Flour, Refer to GB2760-2011) Technical Index Acid value (Calculated by KOH) / (mg/g)50- 86 Ester value(Calculated by KOH) / (mg/g)125- 164 Total lactic acid (W/%)32.0- 38.0 Calcium content (W/%)4.2- 5.2 Pb / mg/kg 2 Packaging Aluminized bag vacuum packing with nitrogen inside. Net weight:20KG/CTN(5KG *4) or packaged with moisture proof paper bag, 25kg/bag.. Storage & Transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and trasporting with materials that is explorsive, combustible or deleterious. The shelf life is 12 months.
Polyglycerol Esters of Fatty Acids(PGE) Chemical Structure: Characters: Straw yellow powder or granular solid which is easily soluble in oils and fats and soluble in organic solvents such as ethanol. It can be dispersed in hot water. Its an non-ionic surfactant with characteristics such as high temperature and acid resistance and HLB value is 7.2. Applications: This product is a kind of hydrophilic monoglyceride, and it can produce strong emulsification effect for oils and fats. 1. It can be used in margarine, butter, shortening oil and oyster sauce as emulsifier and crystal modifying additive to prevent oil-water separation and prolong the preservation period. 2 It can be used in food baking to make oils and fats dispersed more homogeneously in dough to get higher foamability and produce larger volume of product, fine and supple feeling in mouth. 3. It can be added into ice cream to make all components mixed more homogeneous, prevent forming of big ice crystal, help produce fin e and dense pore structure, enhance its expansion ratio and produce smooth and fine feeling in mouth. 4. It can be used in milk beverage as emulsifier, wetting agent, cosolvent and so on. It can also enhance flavor, aroma and color of them. 5. It can be used in meat products to prevent starch aging, shrinkage, water absorption and hardening. 6. It can be used in candies and chocolates to prevent oil-water separation and maintain a good taste. Usage: (1) Since this product is easily soluble in oils and fats, you can dissolve it in oils or fats homogeneously before further processing. (2) You can also dissolve this product in warm water at about 60 homogeneously, and then mix it with other raw materials for further use. Recommended Adding Amount: The addition maximum is 0.01% for bread and pastry, the maximum is 0.3% for ice cream. Technical Index (Refer to GB 1351092): Acid Value (mgKOH/g) 5.0 Saponification Value (mgKOH/g) 120-135 Iodine Value (g/100g) 3.0 Sulfated Ash Content % 1.0 Heavy Metal (Calculated by Pb)% 0.001 Arsenic(Calculated by As)% 0.0003 Melting Point () 53-58 Packaging Aluminized bag vacuum packing with nitrogen inside. Net weight:20KG/CTN(5KG *4) Storage & Transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and trasporting with materials that is explorsive, combustible or deleterious. The shelf life is 12 months.
The new iPAD (intelligent Public Access Defibrillator) from CU Medical builds upon the reputation of the original iPAD for being one of the best value high quality AED's available today. Using low energy biphasic technology (similar to the Philips/Laerdal AED's) it has been designed to be simple to use, easy to maintain, affordable to buy and inexpensive to run. Innovative features and extremely high build quality is making it the AED that the industry is talking about and that other manufacturers are trying to catch up with. Supplied with everything that you need to be up and running, including a FREE carry case (worth 102 +vat) and a FREE Responder Kit the iPAD SP1 Defibrillator offers incredible value and the peace of mind that in an emergency, the only shock you'll get is the one that you want. Key Features Same set of pads for both Adult and Children. Easily switch from Adult to Child mode without changing pads. Integrated pad storage - electrode pads are stored, pre-connected, in a clear compartment on the underside of the unit. - Pads are easily removed by pulling on the exposed tab - The pads are always ready for use and easily checked â?¢ CPR Detection - the iPAD SP1 detects if the CPR is being performed when required. - If CPR is not being performed, voice prompts encourage the responder to â??perform CPRâ?? - If CPR is being performed, voice prompts encourage the responder to â??continue CPRâ?? â?¢ Visual Indicator shows at a glance. - Battery Life - Unit Status - Pad Status. Visual Indicator gives 3 months notice before pads expire. Also, warns user if pre-used electrodes are attached ! â?¢ Internal memory stores the last 5 events/3 hours of data. - Data can be transferred via the built in SD card and IrDA ports - Data can be reviewed via the CU-EX1 software (for pc) Button performs the following functions; - Allows responder to select if CPR metronome is heard during CPR - Checks for faults and errors - Provides handover information to Ambulance crew (usage time and shocks delivered) - Allows the SP1 to be programmed with CPR protocols such as compression rate, number of compressions, breaths and cycles etc, ensuring that the SP1 is always up to date - Downloads data for review - Checks the units software version Longer Shelf-Life of pads and low cost of consumables. FREE carry case 7 year warranty on unit Contents : 1x iPAD SP1 Defibrillator Fully Automatic (AED) 1x Battery 1x Defib. Pads (Adult/Child) 2x AED Starter Kits which contain: 1 Pair of tuffcut scissors, 2 Patient Wipes, 1 Compact Resuscitation Face Shield, 1 Prep Razor and 1 Pair of Gloves. All kit contents are sealed in a foil pouch to ensure sterility. 1x FREE Carry Case
White And Brown Refined Sugar ICUMSA 45 RBU White Refined Sugar- Icumsa 45 RBU Shall Conform To The Following Specifications. The Sugar Being Supplied Is 100% Fit For Human Consumption. Specifications: ICUMSA : 45 RBU ICUMSA Attenuation index units Method # 10-1978 ASH CONTENT : 0.04% Maximum by Weight MOISTURE : 0.04% Maximum by Weight MAGNETIC PARTICLES : mg/kg 4 SOLUBILITY : 100% DRY & Free Flowing GRANULATION : Fine Standard POLARIZATION : 99.80Ã?º Minimum Max AS : 1 P.P.M. Max OS : 2 P.P.M. Max CU : 3 P.P.M. COLOUR : Sparkling White SEDIMENTS : NONE SO : mg/kg 20 REDUCING SUGAR : 0.010% Maximum in Dry Mass RADIATION : Normal w/o presence of cesium or iodine SO2: Certified SUBSTANCE : Solid, Crystal SMELL : Free of any Smell HPN STAPH AUREUS : per 1 gram â?? NIL MICROBIOLOGICAL LIMITS : Pathogenic Bacteria including Salmonella per 1 gram â?? NIL Bacillus per 1 gram â?? NIL PESTICIDE TRACES : Maximum mg/kg Basis DDT 0.005 â?? PHOTOXIN 0.01 â?? HEXACHLORAN â?? GAMMA ISOMER 0.005 CROP: :2013 or more recent crop PHYTOSANITARY CERTIFICATE of no radiation, no virus, no insect parts, no rodent excrement, no husks and no poisonous matter. Product is suitable for HUMAN CONSUMPTION SPECIFICATIONS ICUMSA : 45 RBU MÃ?¡x. or 100 RBU MÃ?¡x. Polarization : 99.8% MÃ?Ân. Ash Content : 0.04% MÃ?¡x. Moisture : 0.04% MÃ?¡x. Solubility : 100% free flowing. Color : Sparkling White Granulation : fine/medium/standard. Radiation : Normal Inspection : SGS or equal Min. Order : 12.500 MT Packaging : 50Kg. PP Bags Terms of Delivery: CIF/CFR ASWP Paymen t: FFDLC Shipment Within 30-45 days after receiving LC Product Available : 10,000,000 MT Product Type: Sugar Type: Crystal Sugar Form: Granular Processing Type: Refined Color: White Packaging: Bag ICUMSA: 45 Brix (%): 99.8 Purity (%): 99.9 Weight (kg): 50 Shelf Life: 24 Months Brand Name: SUGAR ICUMSA 45
