Flexible Perovskite Solar Cells Perovskite is a crystalline material with the general molecular formula ABX3, in the shape of an octahedron. It is widely used in photovoltaics, LEDs and other fields because of high photoelectric conversion efficiency. Perovskite solar cells (PSCs) are utilized perovskite structural materials as light-absorbing materials, and are representative of the third generation of high-efficiency thin-film cells. Perovskite solar cells, as the current global research and development hotspot, are known as the next-generation energy sources as the lowest-cost photovoltaic cells. Compared with traditional crystalline silicon cells, flexible perovskite solar cells have the following features and advantages: 1. Good soft light performance and good light transmittance. 2. High efficiency. The conversion efficiency of perovskite cells is significantly higher than that of crystalline silicon solar cells. 3. Low cost, it means material cost and production cost. (1).Low material cost. The raw materials are all basic chemical materials, do not contain rare elements, are easy to obtain and have lower purity requirements than silicon materials. In addition, the use of perovskite materials is small, and the total thickness is about 1um. (2).Low production cost. Perovskite solar cells mainly use coating process and PVD process, and the production process is greatly simplified, which is suitable for large-scale production. 4. Flexible perovskites solar cells can be produced in roll-to-roll. It is very light in weight, which can save transportation and labor costs. 5. It can be made into color and translucent films, which can achieve different color effects. 6. The flexible perovskite solar cells can be directly attached to the surface of the building structure, and the installation cost is low. Application Flexible perovskite solar cells (FPSCs) have shown great potential in the field of wearable power supply and integration with architectures in the future due to their advantages of high flexibility, light weight, portability, and compatibility with irregular electronic products. The applications are included BIPV , BAPV, Portable Applications, 3C Applications, Active tag& 5G Communication (Sensor + Photovoltaic), Smart Bus Stations and Billboards, Light Boxes, etc.
Model number: x-280a 10r 280w 3in1 wash light led spot moving head with dmx concert light We produce dmx led moving head spot light. We devoted ourselves to stage special effect equipment for many years, covering most of europe and the america market. We are expecting become your long-term partner in china. Specification of the 10r 280w 3in1 wash light led spot moving head with dmx concert light: Power consumption: 470w Power supply: ac 100-240v 50/60hz Light source: 280w 10r lamp Average lifespan: 2200hrs Color wheel: 13 dichroic filters + white Gobo wheel: 9 bidirectional and indexable gobos (outside diameter: 15, 4 mm, image diameter: 13 mm) static gobo wheel with 14 fixed gobos, at variable rotation Prism 1: 8-facet circular prism rotating in both directions at different speeds Prism 2: 6-facet linear prism rotating in both directions at different speeds Zoom: parallel beam angel 2.5â°-20 change Wash effect: adjustable wash effects angle Product features of the 10r 280w 3in1 wash light led spot moving head with dmx concert light: 1. This newest style 280 3in1 disco lights chinese has novel design and compact structure can be as a very professional moving head light 2. It has small beam angle, bean angle scale freely, has multistage beam angle change effect. 3. It has high brightness, downy lighting, and professional linear focus. 4. This new technology fixture even travels efficiently in a case of 4 and will cover all your needs beam, spot, wash
Welcome To Mask Machine ! We are a high quality machine shop that wants to meet your needs in a timely manner. Please look through our pages and see how we can meet your needs.We welcome both new and regular customers at home and abroad to visit us and cooperate with us to achieve mutual profits and create a better future. We are convinced that your partnership with us can help your business scale a new high. Technical Description 1.Adopt Intelligent CNC touch screen Man-Machine Interface System 2.Conveyor Belt, the film can be placed on the belt by worker 3.Output Port : the finished product can be out from there 4.High Speed and Fast Speed Technical Parameters 1.Production Flow Put the dry mask sheet in the belt by hands,then auto folding and bagging 2.Production Speed 3000 to 4000 PCS/H 3.Width of Mask Bag 95-160 mm 4.Length of Mask Bag 140-220 mm 5.Power Source 220 V 6.Power Supply 0.5 KW 7.Pressure 0.6 Mpa Main Parts 1.Servo KINCO 2.Cylinder AIRTAC 1.Solenoid AIRTAC 3.Sensor Taiwan RIKO 4.Sucker AIRTAC 5.PLC Taiwan Delta Main Features 1. PLC + touch screen control system, easy to operate 2.The automatic folding film, automatic load bags, saving labor 3. When No film it will stop to work ,and no bags will alarm, optional automatic and manual functions 4. Stainless steel welded frame, solid and reliable 5. Can be folded single, double and triple mask 6.Can stored 20 groups parameter patterns
Li Series Indoor LED Screen,Indoor LED Wall panel,Indoor Rental LED Screen Item: 500*500 Indoor LED Screen:  Applications: Conferences, Concerts, Stage Background, TV Stations, Shopping Centers,Church LED Video Wall.  Certificates: FCC, CE, EMC, LVD.     Services: 5 Years Warranty  Indoor Rental LED Screen Specification Item Li Series Li Series  Li Series  Li Series Pixe Pictch 2.6mm 2.97mm 3.91mm 4.81mm Led encapsulation SMD1514 SMD1515 SMD2121 SMD2121 Scan Mode 1/24 Scan 1/14 Scan 1/16 Scan 1/13 Scan Pixe Per Sq.m 147,456 Pixel 112,896 Pixel 65,536 Pixel 43,264 Pixel Maintenance methods Front/Rear Service Both Cabinet Material Die Casting Aluminum Module Size(W*H) 250*250mm Cabinet Size(W*H*D) 500*500*80mm Refresh Rate 3840hz Color temperature 8000K ±500 Adjustable Grey Scale 14-16bits Cabinet Weight 8.2KG/Pieces Brightness(Nits/) 1200nits Average Power Consumption 350-400Watt/ Max Power Consumption 800Watt/ IP Protection IP43 Operating Temperature -20°C to 50°C Working Voltage 110-240Volt(50-60hz) Hot Sale LED Video Wall, which include Outdoor Advertising Screens, Indoor Rental LED Screen, Floor Standing LED Display, See-Through LED Display, HD LED Vedio Panel. Low price, high quality. All LED Video Display provides 5 years warranty service. If you want to know more product information, please click here
Si Series Indoor LED Screen,Indoor LED Wall panel,Indoor Rental LED Display Item: 500*500 Indoor LED Screen:  Applications: Conferences, Concerts, Stage Background, TV Stations, Shopping Centers, Church LED Video Wall.  Certificates: FCC, CE, EMC, LVD.     Services: 5 Years Warranty  Indoor Rental LED Screen Specification Item Si Series Si Series Si Series Si Series Pixe Pictch 2.6mm 2.97mm 3.91mm 3.91mm Led encapsulation SMD1514 SMD1515 SMD2121 SMD1919 Scan Mode 1/24 Scan 1/14 Scan 1/16 Scan 1/16 Scan Pixe Per Sq.m 147,456 Pixel 112,896 Pixel 65,536 Pixel 43,264 Pixel Maintenance methods Front/Rear Service Both Cabinet Material Magnesium Alloy Module Size(W*H) 250*250mm Cabinet Size(W*H*D) 500*500*80mm Refresh Rate 3840hz Color temperature 8000K ±500ï¼?Adjustableï¼? Grey Scale 14-16bits Cabinet Weight 6KG/Pieces Brightness(Nits/ã?¡) 1200nits/800~3500nits Average Power Consumption 350-400Watt/ã?¡ Max Power Consumption 800Watt/ã?¡ IP Protection IP43/IP65 Operating Temperature -20°C to 50°C Working Voltage 110-240Volt(50-60hz) Hot Sale LED Video Wall, which include Outdoor Advertising Screens, Indoor Rental LED Screen, Floor Standing LED Display, See-Through LED Display, HD LED Vedio Panel. Low price, high quality. All LED Video Display provides 5 years warranty service. If you want to know more product information, please click here
N Series HD Small Pixel LED Video Wall,HD LED Video Wall,Small Pixel LED Display Item: 600*337.5*85 HD Small Pixel LED Video Wall. Applications: Control Room, Stage , TV Stations, Meeting Room. Certificates: FCC, CE, EMC, LVD.        Services: 5 Years Warranty Small Pixel 16:9 LED Screen Specification Item N Series N Series Not Available Not Available Pixe Pictch 1.25mm 1.56mm 1.875mm 2.5mm Scan Mode 1/30 Scan 1/24 Scan 1/30 Scan 1/30 Scan Pixe Per Sq.m 640,000 Pixel 409,600 Pixel 284,444Pixel 160,000 Pixel Led encapsulation SMD1010 Maintenance methods Front/Rear Service Both Cabinet Material Die Casting Aluminum Module Size(W*H) 160*180mm Cabinet Size(W*H*D) 640*360*58mm Refresh Rate 3840hz Color temperature 10000K ±500 Adjustable Grey Scale 16bits Cabinet Weight 7.4KG/Pieces Brightness(Nits/ã?¡) 1000nits Average Power Consumption 100Watt/Pieces Max Power Consumption 200Watt/Pieces IP Protection IP43 Operating Temperature -10°C to 40°C Working Voltage 110-240Volt(50-60hz) Hot Sale LED Video Wall, which include Outdoor Advertising Screens, Indoor Rental LED Screen, Floor Standing LED Display, See-Through LED Display, HD LED Video Panel. Low price, high quality. All LED Video Display provides 5 years warranty service. If you want to know more product information, please click here
General specification 1. Main features Operationg syetemno Monitor 10.4 inch crt monitor Scanning modeb, 2b, 4b, b/m Keyboardback-lit silicone keyboard (option) Cine loopup to 256 frames Gain0-100db Tgc8 segment Scanning depthup to 240mm Dynamic range0-100db Pseudo-color8 colors Body marking30 Focus4 Magnification1.0, 1.2, 1.5, 2.0 Probe connector2 Languagechinese/english Matching printerlaser/vedio/inkjet/thermal printer Peripheral portusb, vga, dicom3.0, rs232, video out Measurement & calculationdistance, c/a, hr and pw(obstetrics:bpd, crl, ofd, ttd, fl, hc, ac) measurement Image processingdynamic range, dsc, the line average turnover, contrast, edge enhancement, gray-scale transformation&adjustment, brightness, gamma correction 2. Applications Abdominal Gynecology Obstetric(bpd, crl, ofd, ttd, fl, hc, ac) Cardiology Urology 3. Standard configuration Main system unit, 3.5mhz convex probe, user manual and disc 4. Optional items Biopsy bracket, ultrasonic stands, usb flash disk 5. Probes selection 3.5 mhz convex probe (3.5-14mhz variable frequency ) 7.5 mhz linear probe (3.5-14mhz variable frequency ) 7.5 mhz transvaginal probe (3-10mhz variable frequency) 5.0 mhz micro-convex probe (2-6mhz variable frequency) 7.5 mhz rectal probe(80 elements) 6. Advanced technologies User-friendly interface Dual connector support various probes Back-lit keyboard Packaging & delivery Packaging details: box package Net weight: 12 Gross weight: 18kg Package size: 500*400*450mm Delivery time: 5-10 working days Warranty Two years for main unit (one year warranty for probes)
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
S Series Outdoor LED Screen,Outdoor LED Display,Outdoor LED Video Wall Item: Outdoor Football Stadium LED Screen. Applications: Football Stadium. Certificates: FCC, CE, EMC, LVD. Services: 5 Years Warranty Outdoor Football Stadium LED Screen Specification Item S Series S Series S Series S Series S Series Pixe Pictch 4mm 5mm 6mm 8mm 10mm Led encapsulation SMD1921 SMD2727 SMD2727 SMD3535 SMD3535 Scan Mode 1/8 Scan 1/8 Scan 1/8 Scan 1/4 Scan 1/2 Scan Pixe Per Sq.m 62,500 Pixel 40,000 Pixel 27,777 Pixel 15,625 Pixel 10,000 Pixel Module Size(W*H) 256*128mm 160*160mm 192*192mm 256*128mm 320*160mm Cabinet Size(W*H*D) 1024*768mm 960*960mm 960*960mm 1024*768mm 960*960mm Cabinet Weight 45KG/Pieces 55KG/Pieces 40KG/Pieces 45KG/Pieces 50KG/Pieces Max Power Consumption 1200Watt/ã?¡ 1000Watt/ã?¡ 1000Watt/ã?¡ 800Watt/ã?¡ 750Watt/ã?¡ Brightness(Nits/ã?¡) 5500Nits 5500Nits 6000Nits 6500Nits 8000Nits Maintenance methods Rear Service Cabinet Material Steel Refresh Rate 1920hz Color temperature 6500K ±500ï¼?Adjustableï¼? Grey Scale 14-16bits Average Power Consumption 500Watt/ã?¡ IP Protection IP65 Front/Rear Operating Temperature -20°C to 50°C Working Voltage 110-240Volt(50-60hz) Hot Sale LED Video Wall, which include Outdoor Advertising Screens, Indoor Rental LED Screen, Floor Standing LED Display, See-Through LED Display, HD LED Vedio Panel. Low price, high quality. All LED Video Display provides 5 years warranty service. If you want to know more product information, please click here
ON Series Small Pixel LED Screen,Transparent LED Display,High definition LED Vedio Panel Item: 480*480*63 HD Small Pixel LED Video Wall. Applications: Control Room, Stage , TV Stations, Meeting Room. Monitoring Center, Surveillance Center Certificates: FCC, CE, EMC, LVD. Services: 5 Years Warranty Small Pixel LED Screen Specification Item ON Series ON Series ON Series ON Series Pixe Pictch 1.579mm 1.875mm 2.5mm 3mm Scan Mode 1/31 Scan 1/32 Scan 1/32 Scan 1/20 Scan Pixe Per Sq.m 401,111 Pixel 284,444Pixe 160,000Pixel 111,111 Pixel Led encapsulation SMD1010/SMD1515/SMD2020 Maintenance methods Front/Rear Service Both Cabinet Material Die Casting Aluminum Module Size(W*H) 240*240mm Cabinet Size(W*H*D) 480*480*63mm Refresh Rate 3840hz Color temperature 10000K ±500ï¼?Adjustableï¼? Grey Scale 16bits Cabinet Weight 5.5KG/Pieces Brightness(Nits/ã?¡) 1000nits Average Power Consumption 100Watt/Pieces Max Power Consumption 200Watt/Pieces IP Protection IP43 Operating Temperature -10°C to 40°C Working Voltage 110-240Volt(50-60hz) Hot Sale LED Video Wall, which include Outdoor Advertising Screens, Indoor Rental LED Screen, Floor Standing LED Display, See-Through LED Display, HD LED Vedio Panel. Low price, high quality. All LED Video Display provides 5 years warranty service. If you want to know more product information, please click here
