Sintered Filter Cartridge Feature 1. Sintered filter cartridge is surface filtration 2. Sintered filter cartridge is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Sintered filter cartridge has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Sintered Wire Mesh Filter Cartridge Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Maximum Operation Temperature: 816 degree celsius Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Characteristic of Diesel Engine Power Industrial Winch 1.Speedy and efficient 2.Safe and reliable 3.Compact structure 4. Large towing capacity 5.extensively applied to an under construction set of electric power, post and tele wire ways to tower group sets up the pole. 6.apply to use in the wild non-transformer station, it will be convenient and agility. Installation Requirement of Diesel Engine Power Industrial Winch 1. Set up an operating shed and ensure that the operator can see the commander and objects that are being dragged or lifted. Buildings, scaffolding, and stacking of materials and components on the site during construction shall not affect the driver's monitoring of the entire process within the operating range. The operating shed is located in the hazardous work area and the top shall meet the requirements of the protective shelter. 2. Strong foundation. The hoisting machine should be kept away from dangerous working areas as far as possible, and choose a place with a high topography and a strong earthy place. The steel wire ropes used to bury the ground anchors should be securely locked with the hoisting frame and the piles should be piled in front to prevent the movement and tipping of the winch. 3. Reel direction. The center of the reel and the guide pulley is aligned. The distance from the reel to the first guide pulley is as follows: The reeled reel should be more than 15 times the width of the reel, and the slotless reel should be more than 20 times to prevent the reel. The ropes are misaligned with each other during operation of the drum, and the guide wheel flanges and the wire rope are worn.
Specifications Size:1/2"~24" DN15~DN600 Pressure:150lb~600lb,PN20~PN100 Standard reference 1.Design and manufacture standard API599, API6D, DIN3356 2.Face to face dimension standard ASME B16.10,DIN3202-F1 3.Flange connection standard ASME B16.5, DIN2543-2545, EN1092-1. 4.Test and inspection standard API 598, API6D, DIN3230 Material for main parts Body Cast Iron,WCB,WC1,WC6,WC9,C5,CF8,CF8M,CF3,CF3M Plug A182-Gr.F6a, A182-F22.A182-F304 ,F316,F321,F304L,F316 FAQ 1.Q:What is your main market? A:Our main market is North America, South America, Eastern Europe, Southeast Asia, Africa, Mid East, Eastern Asia, Western Europe. 2.Q:Are there products standard? A:Our model is standard, if you have specific demand, pls tell us. 3.Q:Do you have interest to do our own design items? A:Absolutely!It's our pleasure. Our Services 1)Our advantage: We are the manufacturer with almost 20 years experience on valves.Best price,quality and service, Also we can control the production status.NEWSWAY VALVE team with strong ability in designing and after sell service.Cooperation with Carrier has improved our quality to a new level. 2)Terms of payment:T/T, L/C, Western union. 3)Shipment:Average 20-25days after receiving deposit. 4)Delivery:Shanghai/Ningbo ,by sea or air. 5)Gurantee:One year since delivery. 6)Inspection:100% testing for all the valves.
Helical Gearboxes for Print Machine1. Product description Usually we can select one machine which is suitable for you with some informations from you,Website:http://www.srgearboxes.com, such as ratio/motor speed/mounting dimension/ out torque etc. We accept customized products as per your special requirement.2. Characteristics 1)Mounted form: foot-mounted, flange-mounted, axis mounted, shrink mounted. 2)High modularization design: may equip with various motor or other power input conveniently. Same machine type may equip with various power motor. It is easy to realize the combination and junction between every machine type. 3)The gear processed by Carburizing, Nitriding & Grinding.3. Application area Can be used in metallurgy, agitator, mine, blast fan, machine, hoister, energy, compressor, transportation, petroleum industry, water conservancy, air compressor, tobacco, crusher, pharmacy, plastic extruder, printing package, conveyer, chemical industry, textile industry.4. Our service 1) One year warranty from delivery 2)Free components for replacement within warranty period 3)Professional solution provider 4)Free technical support at any time 5)Customer training is available. 6)On-site installation and commissioning is available.5. Product Pictures6. Our Factory7. Our Certificate8. FAQ 1. What's your MOQ for each series gearboxes? 1 unit is ok for different types gearboxes motor.2. How long is your delivery time? Generally it is 30 days. or it is 60 days, it is according to quantity.3. Can you make as per custom drawing? Yes, we offer customized service for customers.4. How about your payment terms? TT, total payment by T/T in advance.5. What about your products' quality ? Don't worry about the quality. There're advanced testing equipments and professional QCs in our company. The testing actions are taken during every procedure from material to the finished products.
PPR 45 DEG ELBOW Water Supply use Material : Polypropylene Random Standard : DIN8077,DIN8088,ISO15874 Connection : Hot melting SIZE :20mm-110mm Working Pressure : 1.25MPA,1.6MPA,2.0MPA,2.5MPA Color : White,green,light grey or according to customer Rongde PPR Fittings Including PPR End Cap, PPR Reducing Elbow, PPR Male Coupling, PPR Reducing Tee, PPR Male Elbow Wall Plate, PPR union , PPR Flange, PPR Female Tee etc. Best quality and factory price will give you. Applications: 1)Hot and cold water pipeline, including solar energy system 2)Heating system, include floor-heating pipeline; 3)Central air-conditioning system 4)Irrigation system 5)Industrial pipeline for supplying or government projects Advantages: 1) Long durability due to high resistance to aggressive elements, which gives the system extremely long service life of 50 years and more. 2) Incomparable smooth and porosity-free internal surface of both pipes and fittings, which results in a very low pressure loss and absence of incrustation. 3) Nontoxic and physiologically harmless material. 4) Resistance to wide range of chemicals and corrosion is avoided in service lines. 5) Heat preservation and energy-saving abilities. 6) High acoustic insulation against fluid noise. 7) Light weight compared to the metallic pipie systems. 8) Convenient and reliable installation methods and No furring while cutting. 9) Cost effective pipeline network and Safe environment with recyclable ability
The main characteristics is a superior wear resistance: Severe wear on the surface has a work-hardening effect on the austenitic structure of this steel. This, when combined with the level of carbon in accordance with the international standards, leads to an increase in hardness from 200BHN (in as delivered plates) up to an in-service hardness of at least 600BHN. Typical Applications: · Quarries and Constructions: Earth moving crusher jaw, grizzly, screen, stone chutes, chain guide and shredder plates, shovel buckets. · Mines: Bucket blade of loader, chain conveyor parts, sprocket wheel, various armouring elements. · Iron Industry, Foundry: Guiding and shifting plates, scraps container, liner of shot blasting unit, pedestal liner, flanged bolster cup, wear liner. · Concrete and Brickworks: Core and dividing wall of parpen mould, grinding mill scraper, mixer paddle. · Scraps â?? Recoveries: Wheel disk, striker and hammer mill. · Automotive Industries: Shot blasting equipment. It is also used for its low coefficient of friction in metal-to-metal applications, its non-magnetic properties in electrical transformer assemblies and for industrial lifting magnets. A high manganese, fully austenitic, quench annealed, non magnetic, work-hardening steel with an exceptionally high level of wear resistance when subjected to work-hardening by shock or high impact pressure in service. The main characteristics is a superior wear resistance: Severe wear on the surface has a work-hardening effect on the austenitic structure of this steel. This, when combined with the level of carbon in accordance with the international standards, leads to an increase in hardness from 200BHN (in as delivered plate) up to an in-service hardness of at least 600BHN. This work-hardening capability renews itself through out in-service life.The underlayers not work-hardened maintain an excellent resistance to shock and a very high ductility.
SC slip ring capsule is a standard,off-the-shelf unit that uses gold contacts at the rotary interface.Color-coded lead wires are used on both the stator and rotor to distinguish, with double contacts & double precision roller bearings, it utilizes 90°V-groove rings to provide smoother running, lower torque and lower electrical noise. Flame-retardant plastic shell,6, 12, and 24 circuit models for Power and /or signal. A.)Specification: Channels 1~24 Ways Voltage 240V AC/DC Current Rating 2A/Ring Speed 300PRM Insulation Resistance 1000M@500VDC Dielectric Strength AC250V@60Hz, 60S Electrical Noise 60 milliohms MAX @ 5~10 rpm,50milliamps,6V DC Lead Size/Type AWG28 Sliver plated coppe,Type ET Teflon Lead Lengths 250mm Operate Temp -20+80 Storage Temp -30+90 B.)Feature: Compact miniature design, small size,fit for harsh space; Double precision roller bearings for lower torque & long life; Signal and power can be combined to deliver in the same slip ring; More installation flanges for option. C.) Option: Higher speed; Metal shell; Available connector and Heat-shrink tube; Length of lead wires can be customized. Our products are widely used in: Security, Factory Automation, Electric Instrumentation, Medical, Aerospace, Marine,Civil and Military Fields. Such as: Crane, Giant Wheel, Cotton Picker, Medical Equipment, Detector,Rotary Tables,Robots,Strander, Webcam, Automatic Revolving Door,Exhibit / Display Equipment, Food Manufacturing Machine,Packaging Machine,Amusement Equipment, Irrigation Machine,Heated Rollers etc.
Description: Explosion-proof slip ring have more safety and more high reliability, it was designed for explosive condition. Fit for oil platform, explosive material packing, agro-product processing, coal mine and spray finishing, etc. Slip rings passing the electricity by rub between the brush and rings, so it is no possible to prevent the spark in theory, Normal slip rings only pay attention on its electric property,but less in protection. So it is very danger to use normal slip rings in explosive condition. Victory-way know the disadvantage of explosion deeply, and we know the philosophy of the explosion, and its protective measures. We designed the Explosion-proof slip ring according to our high reliability slip rings design experience. This slip ring fit for both Explosive Gas atmospheres and Explosive Dust atmospheres, Protect class: IP66. The slip rings passed EX test and got the certificate of conformity fromCNEX (Nanyang),the Cer. No. : CNEx12.2698X. Marking: EX d IIC T6 Gb,DIP A21 Ta,T6 Feature EXd mark, fit for IIC,IIB & IIA; Safest Temp range, reached T6 class, fit for T1~T6 working condition; Working condition: -30,60 ; Protect class IP66, IP68 for option; Can be used in explosive gas and or explosive dust atmospheres (Zone 1 or Zone 2, Zone 21, Zone 22); EPL Class :Gb; Explosion marking: Ex d IIC T6 Gb, DIP A21 TA,T6 (equate to Ex tb IIIC,T6); Stainless steel body have good environmental suitability; Weak signal is viable; Power & Signal can be combined in one body; Without any maintain. Typical Application Oil platform; Explosion-proof packing machine; Spraying equipment; Chemical equipment; Farming industry; Fit for explosive Gas and or Explosive Dust atmospheres; Option: Higher voltage and current capacity Higher speed Wider range of temperature Higher protection class Style of lead exits Flange for install
Hybrid slip ring is designed for setup at the end of shaft or side of the machine,fit for passing fluid + signal or low current power.The slip ring is set in the body of rotary joint, and the wires of rotor lead out from the center. Rotor side has flanges for setup.(More product information welcome to visit slipring.net.) Feature: 1) High quality bearing on both sides of shaft for smoothly operating; 2) High quality sealing materials for long life circle; 3) Special finished shaft provides a excellent wear resistance; 4) Al, Bass, stainless steel body for option; 5) Specially designed leak detection holes; 6) No need to maintain. Technical spec: Speed 100Rpm Operate temperature -30,90 protect degree IP54 Housing Al alloy Part A:(Electornic Slip Rings) Channels 12 rings(for signal) Operation Voltage 0~240VAC/DC Current 2A/Ring Contact material Precious Metal Electric Nosice Max.40m Ω Dielectric strength 500VAC@50Hz,60s Insulation resistance 500MΩ @600VDC Part B:(Rotary Joint) Channels 2 Ways Pressure 1.6Mpa Max Media compressed air/ vacuum Our products are widely used in: Security, Factory Automation, Electric Instrumentation, Medical, Aerospace, Marine,Civil and Military Fields.Such as: Crane, Giant Wheel, Cotton Picker, Medical Equipment, Detector,Rotary Tables,Robots,Strander, Webcam, Automatic Revolving Door,Exhibit / Display Equipment, Food Manufacturing Machine,Packaging Machine,Amusement Equipment, Irrigation Machine,Heated Rollers etc.
High current slip ring was designed for welding machine, planting line, electric generating set, and high current charging set. this kind of slip rings usually using carbon alloy, copper alloy or silver alloy as contact material. High current working condition need reliable contact and good radiating. Victory-way select the best fit contact material according to customers work condition. Constant pressure set and running-in contact surface lead good contact. Low resistance and optimized radiating structure to make sure the slip rings can used for long time stability. Type Code Most of high current slip ring was designed for customer, so there havent standard product, below sheet is some typical high current slip ring for reference, If you have same require, please contact us ,and we will select the best fit product for you. No Model Inner size Current (A) Voltage(V) Speed(Rpm) Ways Contact material Type 1 DTS-38X3P120 38 120 380V 3000 3 Sliver Separated 2 DT-65X3P360 65 360 380 120 3 Copper integral Feature High current; Wide Temp range:-60,260; Without any maintain; Easy to setup; Typical Application Rotary index tables, test equipment; Plating line. High-power system Cable reels. Option Higher voltage and current capacity Higher speed Wider range of temperature Higher protection class Style of lead exits Flange for install Our products are widely used in: Security, Factory Automation, Electric Instrumentation, Medical, Aerospace, Marine,Civil and Military Fields.Such as: Crane, Giant Wheel, Cotton Picker, Medical Equipment, Detector,Rotary Tables,Robots,Strander, Webcam, Automatic Revolving Door,Exhibit / Display Equipment, Food Manufacturing Machine,Packaging Machine,Amusement Equipment, Irrigation Machine,Heated Rollers etc.
Plug straightly slip ring is also known as connect directly slip ring or plug-in slip ring.It is also called thermocouple slip ring or thermal resistance slip ring according to practical use. The H series slip rings are compact, cost effective, mercury free, designed for industrial manufacturing.Standard H3 has three rings, each is able to carry 7 amps. H series slip rings overcome mercury slip ring's disadvantages of not environmental protection and use on environment-demanding. Advanced technology and reliable structure, maximum utilization of contact materials realize the highest performance but low cost.Standard terminals fit to quickly install. This product is fully compatible with Moog P4 slip ring and can also replace mercury slip ring M330,A3H, etc. They are best applicable in the food production industry and packaging industry. A.)Outline: B.)Specification: Voltage: 240V AC/DC Current Rating:7A/Ring Speed:400PRM Insulation Resistance:200M@500VDC Dielectric Strength:AC 600V@60Hz, 60S Electrical Noise:10 milliohms MAX @5rpm,50milliamps,DC Contact Material:Precious metal Operate Temp: -20+80 Storage Temp:-30+85 C.)Feature: Mercury free; Reliable & rotational connections for power, signal and data transmission; Speeds up to 400rpm; Fast mounting. D.)Application: Rotary tables and rotary sensors; Robots; Test equipment; Exhibit / display equipment; Heated rollers; Food manufacturing machine; Automation equipment; Packaging machine. E.)Option: Higher voltage and current; Higher speed; Wider range of temperature; Higher protection class; Layout & size of terminals can be customized; Flange for installation.
Hastelloy C276 Sheets Plates & Coils Manufacturer, Hastelloy ASME SB575 Shim Sheets, Hastelloy C22 Perforated Coils, Hastelloy Sheets Plates Coils Exporter ASTM B575 Hastelloy B2 Cold Rolled Sheets , Hastelloy X Blank Sheets, Hastelloy X Flat Plates, ASME SB333 Hastelloy Coils, Hastelloy Plain Sheets & Plates Leading Manufacturers. Hastelloy X Chequered Sheets, Hastelloy B2 Hot Rolled Plates , Hastelloy C22 Strips Sheets Plates & Coils Suppliers. We offer a qualitative variety of these Hastelloy Sheets in the market. Made as per the set industry rules, these Hastelloy Alloy Plates have strong design in nature. Meanwhile, as a manufacturer, supplier, stockiest and exporter, we offer these sheets, plates and coils in custom-made sizes and thicknesses as per the exact demands of our esteemed clients. ASTM B575 / B333 Hastelloy Sheets Plates & Coils Specification Specifications : ASTM / ASME SB 575, ASTM / ASME SB 333 Dimensions :ASTM, ASME and API Length : Single Random, Double Random & Cut Length Size:6 mm to 120 mm. Finish :Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) Hardness :Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc. Specialize :Shim Sheet, Perforated Sheet, B. Q. Profile. Grade : Hastelloy C276 (UNS No. N10276), Hastelloy C22 (UNS No. N06022), Hastelloy B2 (UNS No. N10665), Hastelloy C-4 (UNS No. N06455) Form:Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange)
Hastelloy C276 Sheets Plates & Coils Manufacturer, Hastelloy ASME SB575 Shim Sheets, Hastelloy C22 Perforated Coils, Hastelloy Sheets Plates Coils Exporter ASTM B575 Hastelloy B2 Cold Rolled Sheets , Hastelloy X Blank Sheets, Hastelloy X Flat Plates, ASME SB333 Hastelloy Coils, Hastelloy Plain Sheets & Plates Leading Manufacturers. Hastelloy X Chequered Sheets, Hastelloy B2 Hot Rolled Plates , Hastelloy C22 Strips Sheets Plates & Coils Suppliers. We offer a qualitative variety of these Hastelloy Sheets in the market. Made as per the set industry rules, these Hastelloy Alloy Plates have strong design in nature. Meanwhile, as a manufacturer, supplier, stockiest and exporter, we offer these sheets, plates and coils in custom-made sizes and thicknesses as per the exact demands of our esteemed clients. ASTM B575 / B333 Hastelloy Sheets Plates & Coils Specification Specifications : ASTM / ASME SB 575, ASTM / ASME SB 333 Dimensions :ASTM, ASME and API Length : Single Random, Double Random & Cut Length Size:6 mm to 120 mm. Finish :Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) Hardness :Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc. Specialize :Shim Sheet, Perforated Sheet, B. Q. Profile. Grade : Hastelloy C276 (UNS No. N10276), Hastelloy C22 (UNS No. N06022), Hastelloy B2 (UNS No. N10665), Hastelloy C-4 (UNS No. N06455) Form:Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange)
Hastelloy C276 Sheets Plates & Coils Manufacturer, Hastelloy ASME SB575 Shim Sheets, Hastelloy C22 Perforated Coils, Hastelloy Sheets Plates Coils Exporter ASTM B575 Hastelloy B2 Cold Rolled Sheets , Hastelloy X Blank Sheets, Hastelloy X Flat Plates, ASME SB333 Hastelloy Coils, Hastelloy Plain Sheets & Plates Leading Manufacturers. Hastelloy X Chequered Sheets, Hastelloy B2 Hot Rolled Plates , Hastelloy C22 Strips Sheets Plates & Coils Suppliers. We offer a qualitative variety of these Hastelloy Sheets in the market. Made as per the set industry rules, these Hastelloy Alloy Plates have strong design in nature. Meanwhile, as a manufacturer, supplier, stockiest and exporter, we offer these sheets, plates and coils in custom-made sizes and thicknesses as per the exact demands of our esteemed clients. ASTM B575 / B333 Hastelloy Sheets Plates & Coils Specification Specifications : ASTM / ASME SB 575, ASTM / ASME SB 333 Dimensions :ASTM, ASME and API Length : Single Random, Double Random & Cut Length Size:6 mm to 120 mm. Finish :Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) Hardness :Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc. Specialize :Shim Sheet, Perforated Sheet, B. Q. Profile. Grade : Hastelloy C276 (UNS No. N10276), Hastelloy C22 (UNS No. N06022), Hastelloy B2 (UNS No. N10665), Hastelloy C-4 (UNS No. N06455) Form:Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange)
Inconel 600 Sheets Plates & Coils Manufacturer, Inconel Alloy 625 Shim Sheets, Inconel 718 Perforated Coils Exporter. Inconel Alloy Cold Rolled Sheets, 800 Incoloy Hot Rolled Plates,ASME SB168 Inconel Coils, Inconel Strips Exporter, Inconel Plain Sheets & Plates Leading Manufacturers. ASTM B424 Incoloy 825 Chequered Sheets, Inconel DIN 2.4816 Sheets Coils, Inconel 601 Shim Plates, Inconel Sheets Plates & Coils Suppliers. Manufactured in accordance with the set industry guidelines, these Inconel Alloy Plates have robust design. We offer these Inconel Plates in international and national quality of standards at cost-effective rates to our patrons. Meanwhile, as a manufacturer, supplier, stockiest and exporter, we offer these sheets, plates and coils in custom-made sizes and thicknesses as per the exact demands of our esteemed clients. ASTM B424 / 168 / 443 Inconel Sheets Plates & Coils Specification Specifications : ASTM / ASME SB 168, ASTM / ASME SB 424 , ASTM / ASME SB 443 Dimensions : ASTM, ASME and API Size : 0.5 MM TO 200 MM THICK IN 1000 MM TO 2500 MM WIDTH & 2500 MM TO 12500 MM LENGTH Finish : Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) Hardness : Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc. Specialize : Shim Sheet, Perforated Sheet, B. Q. Profile. Grade : Inconel 600 Bars UNS N06600, Inconel 601 Rods UNS N06601, Inconel 625 Wire UNS N06625, Incoloy 800 Bars UNS N08800, Incoloy 800H / HT Rods UNS N08810, Incoloy 825 Round Bars UNS N08825 Form : Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange)
Inconel 600 Sheets Plates & Coils Manufacturer, Inconel Alloy 625 Shim Sheets, Inconel 718 Perforated Coils Exporter. Inconel Alloy Cold Rolled Sheets, 800 Incoloy Hot Rolled Plates,ASME SB168 Inconel Coils, Inconel Strips Exporter, Inconel Plain Sheets & Plates Leading Manufacturers. ASTM B424 Incoloy 825 Chequered Sheets, Inconel DIN 2.4816 Sheets Coils, Inconel 601 Shim Plates, Inconel Sheets Plates & Coils Suppliers. Manufactured in accordance with the set industry guidelines, these Inconel Alloy Plates have robust design. We offer these Inconel Plates in international and national quality of standards at cost-effective rates to our patrons. Meanwhile, as a manufacturer, supplier, stockiest and exporter, we offer these sheets, plates and coils in custom-made sizes and thicknesses as per the exact demands of our esteemed clients. ASTM B424 / 168 / 443 Inconel Sheets Plates & Coils Specification Specifications : ASTM / ASME SB 168, ASTM / ASME SB 424 , ASTM / ASME SB 443 Dimensions : ASTM, ASME and API Size : 0.5 MM TO 200 MM THICK IN 1000 MM TO 2500 MM WIDTH & 2500 MM TO 12500 MM LENGTH Finish : Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) Hardness : Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc. Specialize : Shim Sheet, Perforated Sheet, B. Q. Profile. Grade : Inconel 600 Bars â?? UNS N06600, Inconel 601 Rods â?? UNS N06601, Inconel 625 Wire â?? UNS N06625, Incoloy 800 Bars â?? UNS N08800, Incoloy 800H / HT Rods â?? UNS N08810, Incoloy 825 Round Barsâ?? UNS N08825 Form : Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange)
Inconel 600 Sheets Plates & Coils Manufacturer, Inconel Alloy 625 Shim Sheets, Inconel 718 Perforated Coils Exporter. Inconel Alloy Cold Rolled Sheets, 800 Incoloy Hot Rolled Plates,ASME SB168 Inconel Coils, Inconel Strips Exporter, Inconel Plain Sheets & Plates Leading Manufacturers. ASTM B424 Incoloy 825 Chequered Sheets, Inconel DIN 2.4816 Sheets Coils, Inconel 601 Shim Plates, Inconel Sheets Plates & Coils Suppliers. Manufactured in accordance with the set industry guidelines, these Inconel Alloy Plates have robust design. We offer these Inconel Plates in international and national quality of standards at cost-effective rates to our patrons. Meanwhile, as a manufacturer, supplier, stockiest and exporter, we offer these sheets, plates and coils in custom-made sizes and thicknesses as per the exact demands of our esteemed clients. ASTM B424 / 168 / 443 Inconel Sheets Plates & Coils Specification Specifications : ASTM / ASME SB 168, ASTM / ASME SB 424 , ASTM / ASME SB 443 Dimensions : ASTM, ASME and API Size : 0.5 MM TO 200 MM THICK IN 1000 MM TO 2500 MM WIDTH & 2500 MM TO 12500 MM LENGTH Finish : Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) Hardness : Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc. Specialize : Shim Sheet, Perforated Sheet, B. Q. Profile. Grade : Inconel 600 Bars UNS N06600, Inconel 601 Rods UNS N06601, Inconel 625 Wire UNS N06625, Incoloy 800 Bars UNS N08800, Incoloy 800H / HT Rods UNS N08810, Incoloy 825 Round Bars UNS N08825 Form : Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange)
4-person bench tablematerial10 gauge bench top flanged 2" all aroundsupportbench top supported by 2-1/2" schedule 40 steel pipe supports,intermediate supports provided at36" on center where bench exceeds 4" lengthdimensions50"W X 72"L X 30"Hfinishingpowder coat finishstainless steel bench topall stainless steelBench Table Designed for heavy duty institutional seating needs. Tops and benches are 10 gauge, vertical support is contracted of 7 gauge formed channels. Seat support is 2"x3"x3/16" angle. Features include prime finish, bolted or welded in place, shipped fully assembled, and warrantee to match project specifications. Options include powder coat finish available, seat top can be mild steel or stainless, available in 8 seat configurations, embedded sublimation image available, and engineered to your projects specifications. Construction: Table top fabricated from 12 gauge steel stainless steel optional. Seats fabricated from 14 gauge steel with stainless steel optional. Table top and seats to be smooth, true, level, and free of sharp edges. Floor mounting plate to be 3/8" thick 18" square with 4 holes for anchor bolt installation. One piece welded assembly and all welds neatly finished. Powder-coat finish, with standard color on all mild steel components and color to be selected by architect. Game top will be embedded into the surface to a depth of less then one millimeter.FAQ Q.1: About MOQ: Small quantity is acceptable. Q.2: Can you produce by OEM? Welcome, you can send your own design and drawings. Q.3: What about warranty ? We are very confident in our products, and we pack them very well, so usually you will receive your order goods in good condition. But due to long time shipment damage will be negotiated to settle well. Any quality issue, we will deal with it immediately.
Application and features : Applies in the workshop production of PE, PP, PVDF elbow, equal tee, four-way such as diameter, extended injection short pipe fittings, production pipe assembly; 45 ° and 60 ° y-shaped tee (Y type tee needs to choose and buy of 45 ° and 60 ° y-shaped three-way welding jig); Integration structure design, different welded pipe need to change the corresponding fixture can; The heating plate temperature control system independently, teflon coating; Electric cutter, safety limit switch, prevent accidental start milling cutter; Low start-up pressure, and high reliability sealing structure; Independent dual channel timer, can record the two periods of heat and cooling, timing alarm over, convenient for the user. Big dial, high-precision shock pressure, more readings clear; The heating plate, cutter adopts tilting, convenient operation; Products comply with 98/37 / EC and 73/23 / EEC standards. Optional components: Short flange welding special fixture. Short pipe welding special fixture 45 °, 60 ° y-shaped three-way welding jig The Main parameters: Model SD-AF315 Pipe sizes (mm) 90,110,125,140,160,180,200,225,250,280,315 Applications 0~90°Elbow, tee, cross, 45° and 60° wyes(optional parts should be used) Heating plate Max. Temp. 270?? Temp. deviation in surface(170~250??) ±7?? Pressure adjustable ranges 0ï½?16MPa Working voltage 380V,50Hz Heating plate power 5KW Hydraulic unit power 1.5 KW Planing tool power 0.75 KW Total power 7.25 KW Weight 760KG(Don`t include optional parts ) Packing Cases 4 Plywood Cases Volume 3.1 CBM
Johnson stainless steel Slot Continuous screen for sand control (customized): Johnson Wedge wire screen also be named Vee-Wire screen pipe,Continuous slot Vee-wire screen tube,Water well screen, Wire wrapped screen,Wire wound screen,water filter, etc. It is made up of Vee-shaped wrapped wire and round rod in each intersection,welded together. Accurate slot and high filtration precision. 1.Name: stainless steel Slot Continuous screen for sand control (customized) 2.Material details: stainless steel 304 316L, carbon steel, 3.Hole Shape: Vee shaped 4.Slot size: 0.02mm~15mm, Customized 5.Length: up to 6m, Customized 6.Color: Original Matel color 7.Application: water well screen, filter, mining, coal, petroleum, fertilizer, grain 8.Wire shape: V type wedge wire 9.connection type: weld/thread/flange 10.surface treatment: galvanzied or coating 11.End Connection: Plain, Beveled or Thread Coupling 1.Inroduction: The welded stainless steel water well screen is made up of support wire and filter wire. with the material of stainless steel 302,304,316,304L,316L. 2.Component: The support wires can be round wires, triangular wires or trapezoidal wires, while the filter wires is triangular wires(V shape wires). 3.Characteristics: precise aperture size, high filter precision,firm structure, high-temperature resistance, corrosion resistance and mechanical performance is good,long service life, safe and reliable, etc. Can be used in various media filtration and screening. 5.Application of Wedged wire screen/Johnson screen pipe/Water Filter tube: Separating , filtering; Dewatering; Classifying; Straining , drying ; Water intak; 6.Feature of Vee type Johnson slotted wire screen tube: Non-clogging surface. Large open area. Low pressure drop. Hydraulic efficiency. High flow rates. Mechanical strength. Abrasion-resistant. Easy cleaning.
