SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Products - German Origin - Product List With Pricing Details Refined/produced In Germany, Not Re-Documented Category A (AVIATION KEROSENE) 1.Jet Fuel A-1 2.Jet Fuel TS-1 Category B (D2/EN590) 1.Diesel 10 PPM (Gasoil 0.001%S) 2.Diesel 50 PPM (Gasoil 0.005%S) 3.Diesel 500 PPM (Gasoil 0.05%S) 4.Diesel 1000 PPM (Gasoil 0.1%S) 5.Diesel 2500 PPM (Gasoil 0.25%S) Category C (PETROL) 1.Unleaded Gasoline RON 92 2.Unleaded Gasoline RON 95 3.Unleaded Gasoline RON 97 Category D (D6 RESIDUAL FUEL) 1.Fuel Oil 3.5% 180 CST 2.Fuel Oil 3.5% 380 CST
* Quantity MIN 1,000,000 Barrels x 12 months * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * Payment is then made by Seller, who carries out all commissions transfers. * Contract: 12 Months with possible rollovers. * Inspection: SGS or similar * CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyer's bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Seller's fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
* Quantity : MIN 50,000MT x 12 months * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * payment is then made by Seller, who carries out all commissions transfers. * Contract: 12 Months with possible rollovers. * Inspection: SGS or similar CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyers bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Sellers fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
* Quantity MIN 1,000,000 Barrels x 12 months with R/E * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * Payment is then made by Seller, who carries out all commissions transfers. *Contract: 12 Months with possible rollovers. * Inspection: SGS or similar * CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyer's bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Seller's fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
* Quantity MIN 1,000,000 Barrels x 12 months * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * Payment is then made by Seller, who carries out all commissions transfers. Contract: 12 Months with possible rollovers. Inspection: SGS or similar * CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyer's bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Seller's fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
* Quantity MIN 50,000MT x 12 months * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * payment is then made by Seller, who carries out all commissions transfers. * Contract: 12 Months with possible rollovers. * Inspection: SGS or similar * CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyer's bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Seller's fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
* Quantity MIN 50,000MT x 12 months * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * payment is then made by Seller, who carries out all commissions transfers. * Contract: 12 Months with possible rollovers. * Inspection: SGS or similar * CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyer's bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Seller's fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
* Quantity MIN 50,000MT x 12 months * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * payment is then made by Seller, who carries out all commissions transfers. * Contract: 12 Months with possible rollovers. * Inspection: SGS or similar CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyer's bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Seller's fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
* Quantity MIN 50,000MT x 12 months * Origin: Russian Federation Specifications: Standard Export Quality. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. Commissions * Payment is then made by Seller, who carries out all commissions transfers. * Contract: 12 Months with possible rollovers. * Inspection: SGS or similar * CIF DLC or SBLC PROCEDURE 1. Buyer issues ICPO, company registration, I.D. and Top World Bank redacted Bank Statement or equivalent 2. Seller issues Sales and Purchase Agreement (SPA). 3. Buyer signs and returns SPA. 4. Buyer's Bank issues a RWA letter to guarantee to issue an instrument on behalf of the Buyer within three working days after receiving the following PPOP. 5. Seller issues PPOP to Buyer including the following: A. Copy of license to export issued by the Department of the Ministry of Energy. 8 B. Copy of approval to export issued by the Department of Ministry of Justice. C. Copy of statement of availability of the product. D. Copy of the refinery commitment to produce the product. E. Copy of contract to transport the product to port F. Copy of the port storage agreement G. Copy of the charter party agreements to transport the product to the discharge port. H. Tank Storage Receipt (TSR) I. Q & Q by Current SGS report. 6. Buyer's bank issues operative Letter of Credit DLC MT 700 or SBLC MT-760 to Seller's fiduciary Bank account. 7. Seller issues 2% Performance Bond to Buyers bank. 8. Shipment Commences 9. On getting to Buyer's port of discharge, the Buyer's inspection team board the vessel and perform an inspection. Buyer sends SGS report to Seller. 10. Seller provides shipping document and a master commercial invoice to Buyer, within 3 banking days, Buyer makes the payment in full via MT 103/TT to Seller's Bank account.
Frankincense Boswellia Sacra Essential Oil Uses and Benefits : Benefits of Frankincense Oil 1. Helps Reduce Stress Reactions and Negative Emotions When inhaled, frankincense oil been shown to reduce heart rate and high blood pressure. It has anti- anxiety and depression-reducing abilities, but unlike prescription medications, it does not have negative side effects or cause unwanted drowsiness. 2. Helps Boost Immune System Function and Prevents Illness Studies have demonstrated that frankincense benefits extend to immune-enhancing abilities that may help destroy dangerous bacteria, viruses and even cancers. Researchers at Mansoura University in Egypt conducted a lab study and found that frankincense oil exhibits strong immunostimulant activity. It can be used to prevent germs from forming on the skin, mouth or in your home. This is the reason many people choose to use frankincense to naturally relieve oral health problems. The antiseptic qualities of this oil may help prevent gingivitis, bad breath, cavities, toothaches, mouth sores and other infections from occurring, which has been shown in studies involving patients with plaque-induced gingivitis. 3. May Help Fight Cancer and Deal with Chemotherapy Side Effects
Frankincense Boswellia Sacra Essential Oil Uses And Benefits Benefits of Frankincense Oil 1. Helps Reduce Stress Reactions and Negative Emotions When inhaled, frankincense oil been shown to reduce heart rate and high blood pressure. It has anti-anxiety and depression-reducing abilities, but unlike prescription medications, it does not have negative side effects or cause unwanted drowsiness. 2. Helps Boost Immune System Function and Prevents Illness Studies have demonstrated that frankincense benefits extend to immune-enhancing abilities that may help destroy dangerous bacteria, viruses and even cancers. Researchers at Mansoura University in Egypt conducted a lab study and found that frankincense oil exhibits strong immunostimulant activity. It can be used to prevent germs from forming on the skin, mouth or in your home. This is the reason many people choose to use frankincense to naturally relieve oral health problems. The antiseptic qualities of this oil may help prevent gingivitis, bad breath, cavities, toothaches, mouth sores and other infections from occurring, which has been shown in studies involving patients with plaque-induced gingivitis. 3. May Help Fight Cancer and Deal with Chemotherapy Side Effects Several research groups have found that frankincense has promising anti-inflammatory and anti-tumor effects when tested in lab studies and on animals. Frankincense oil has been shown to help fight cells of specific types of cancer. Researchers in China investigated the anticancer effects of frankincense and myrrh oils on five tumor cells lines in a lab study. The results showed that human breast and skin cancer cell lines showed increased sensitivity to the combination of myrrh and frankincense essential oils. A 2012 study even found that a chemical compound found in frankincense called AKBA is successful at killing cancer cells that have become resistant to chemotherapy, which may make it a potential natural cancer treatment. 4. Astringent and Can Kill Harmful Germs and Bacteria Frankincense is an antiseptic and disinfectant agent that has antimicrobial effects. It has the ability to eliminate cold and flu germs from the home and the body naturally, and it can be used in place of chemical household cleaners.
* KF94 , KF80, NANO, BIO-C, 4 Ply. 3 Ply Dental. etc * Made in Korea Product !! 1. High Quality A : 0.3 $~0.5 $ FDA CE Medical Grade 2. High Quality B : 0.15 $~0.2 $ FDA CE Medical Grade 3. General Grade : 0.1 $ ~ 0.3 $ General Purpose. 4. Dental FFP3 : 0.1 $~ 0.2 $ [Special Offer] * Any Amount , Any Grade, Any kinds of Face Mask Supply Avail. * Deliver by AirExpress, Ocean Container ship avail * OTG Stock avail. Any amount (Any amount, 1 piece Mask Can Deliver) * Any Condition Requirment Avail to Go ~~ * Any Price Can match !!
Sodium Feldspar: Mineral has multiple quality varieties (grades) that determine its applicability in a given industry. After mining the rocks in a crude form were sorted for quality via processing machines. Thereafter, they are downsized in a variety of sizes, depending on the requirement of a customer to fulfill various industrial needs. Specifications : Lumps : 50 - 150 MM Chips : 1 - 5 MM Powder : 325 Mesh (Microns) 30 Mesh (Microns) Type : Sodium Feldspar, Potassium Feldspar, Quartz, Ball Clay, Limestone, Dolomite
Postassium Fledspar: Mineral has multiple quality varieties (grades) that determine its applicability in a given industry. After mining the rocks in a crude form were sorted for quality via processing machines. Thereafter, they are downsized in a variety of sizes, depending on the requirement of a customer to fulfill various industrial needs. Specifications : Lumps : 50 - 150 MM Chips : 1 - 5 MM Powder : 325 Mesh (Microns) 30 Mesh (Microns) Type : Sodium Feldspar, Potassium Feldspar, Quartz, Ball Clay, Limestone, Dolomite
Quartz: Mineral has multiple quality varieties (grades) that determine its applicability in a given industry. After mining the rocks in a crude form were sorted for quality via processing machines. Thereafter, they are downsized in a variety of sizes, depending on the requirement of a customer to fulfill various industrial needs. Specifications : Lumps : 50 - 150 MM Chips : 1 - 5 MM Powder : 325 Mesh (Microns) 30 Mesh (Microns) Type : Sodium Feldspar, Potassium Feldspar, Quartz, Ball Clay, Limestone, Dolomite