Caterpillar sem659 wheel loader Main feature: 1, engine: be reoptimized and rematched, improved efficiency and performance, improved cold start capacity. 2, cooling: designed by crdc (caterpillar china research & design center), the cooling system brings end results of optimal cooling efficiency, increased fuel efficiency, less radiator plugging even under extreme hot temperature or dusty work environment. 3, transmission: zf transmission; german brand; countershaft design; 4forward & 3 reverse, power shift; eh controlled shuttle, soft and smoothly; kick-down switch for increased productivity; reliable and durable. 4, axle: large module gears, tuned for heavy duty with durability 5, cab: improved operator comfort and visibility; reduced in cab noise, meet gb standard, reliability improved; integrated fops/rops cab is available. 6, electrical: large capacity delphi battery; high quality electrical components. 7, structure: finite element analysis (fea) design, refined for heavy duty application. 8, hydraulic: valve [ccmc (caterpillar china machinery component) components; single lever, joystick controlling (optional)] Hose [ccmc hose, improved strength and reliability, optimized hose and tube routing] Pump [durable permco hydraulic pump, us brand] Engine Engine------shanghai power co., ltd Model------c6121zg10h (authorized by cat3306) Type------linear, water cooling, 4-stroke, direct injection, turbocharged Cylinder-bore íß stroke------6-126íß130mm Max torque------843nm Rated power------162kw Displacement ------- 10.5l Rated rotate speed------2200r/min Seaworthy
G assembly, power head, cooling(thermostat), cooling(water pump), head gaskets, electrical, drive shaft housing gear sets, upper housing, lower housing, gear case seal/bearing & gear kit, gearing housing bearing, oil seals, piston kits, thrust bearings, roller bearings, cage bearings, power packs and amplifiers, propeller, water pump show out, housing, cup, impeller, washer, screw, nut, tube guide, o-ring, key, gasket, wear plate, water pump base, shim, bushing assembly, clip, shift shaft, insert, trim tab, shift spool, shift crank, cross pin, clutch dog, prop shaft, thrust ring, ball bearing, bearing carrier, tab washer, cover nut, thrust hub, lock washer, lock nut, slinger, drive shaft, anode, draining screw, shift cable tool, bearing retainer wrench, shift shaft bushing tool, pinion gear shimming tool, drive shaft adaptor, drive gear shimming tool, bearing carrier retainer wrench, pinion nut adaptor kit, hinge pin tool, engine alignment tool, trim cylinder, rear anchor pin, rod scraper, floating piston, springs, steel ball, shock piston, cylinder housing kit, plate seal, centering cone, gimbal bearing, clamp, spacer, cotter pin, reverse gear, screen!ketc. 828692q1 cover assembly 94998a4 Cover assembly
Famous Engine Optimized low speed torque capability and machine productivity Strong torque delivery leads to higher breakout force Best-in-class fuel efficiency Efficient Hydraulic System Twin pump flow merging hydraulic system increasesmachine efficiency The optimized hydraulic system paired with the drive train reduces machine cycle time and increasesproductivity Joystick hydraulic control for easy and preciseoperation Operator Station Premium operator station withbig space and superior visibility Patented MAC mount providesless noise and increased comfort Adjustable suspension seat Sliding side window and AC withfresh air circulation provideoperator comfort Single lever shifting is flexible andconvenient Adjustable air flow outlet deliversbetter defrost performance Reliable Drivetrain Countershaft transmission with upgraded core componentsprovides high reliability Large rim-pull in 1st gear and higher speed in 2nd gear provide high efficiency for load and carry applications Clutch cutoff selection switch ensures stable and safe operation Torque convertor structure is simple and efficiency is high The SEM designed and built axle provides best in class performance in heavy duty applications Advanced Cooling System The standard cooling package provides high reliability in 50 ambient conditions. Shock pad mounts ensure reliability under severe applications Solid Structure Structures undergo Finite Element Analysis (FEA) and On Machine Stress Analysis (OMSA) to ensure durability Performance Series (PS) buckets improve loading capability Serviceability System pressure test ports are standard Big angle engine hood side open door provides easy service access Torque convertor is isolated from transmission making it easy to service Safety Safety design complies with all regulatory requirements Production System (CPS) leveraged in manufacturing process 3-point touching design provides convenient operator entering to cabin Backup alarm ensures machine safety Environmentally friendly painting process Machine Applications The sturdy design of the 655D makes it the perfect machine for large volume earthmoving applications In Hopper feeding and Coal loading applications the 655D can load more, move faster and burn less fuel Multiple work tools are available for increased versatility
Features: V2 Head Rotor Set (4mm Shaft) V2 Tail Rotor Set Auto-Rotation System Rear Tail Servo Mount Collective Pitch System Tail Rotor Drive Belt System Main Drive Gear with Cooling Fan Professional Servo Control Lever Design Specification: Length:650mm Height:230mm Main Rotor:700mm Tail Rotor:150mm Motor Gear:13T/11T Main Gear:150T Autorotation Tail Drive Gear:106T Tail Drive Gear:25T Drive Gear Ratio:1:11.5:4.24/1:13.6:4.24 Weight(without power system):354g Weight(including power system):690g Package included: 450S V2-01 Kit ONLY (95% Assembled without electric parts) x 1
Butterfly Valve,Butterfly Valve Supplier Size : NPS 2â?¼24, DN50~600, JIS 50~600A Rating : Class 150, PN6 PN10 PN16, JIS 5K 10K 16K Category : concentric-pivoted , eccentric-pivoted, double-eccentric Material : FC, FCD, WCB, CF8, CF8M Seat : NBR ,EPDM, PTFE, VITON Driving gear : lever-type, gear-type Related standard : API 609 , EN 593, JIS F7480 API 598 , EN 12266, JIS F7400
There are lots of various excavator parts we wholesale at home and abroad, such as engine series, hydraulic pump series, oil seals series and gear box series. What is more, customer-friendly products vary in different oil seals with gw, cylinder seal kits, separate seals, o-ring kits, bushing, floating seals and coupling, hydraulic rod seals, etc. We have specialized in wholesaling various accessories for caterpiller, komatsu, hitachi, kobelco, kato, sumitomo, volvo, hyundai, doosan and daewoo excavators.
Features: 1. Free steel reducer gear 2. Runva patent two stage planetary gear reducer 3. Two speed and clutch integrate with one handgrip 4. Runva patent clutch and speed shift structure 5. Clutch and two gear actions auto engagement 6. Automatic screw cone braking action 7. Low oil flow stable working motor 8. Vehicle's existing steering power pump drive 9. DC 12V or DC 24V Power drive optional 10. Remote control 11. Wireless remote control availabl 12. SWR tensioner available 13. Can not use it working as lift.
Wondee Autoparts, as a one-stop supplier, provides a variety of landing gears: Loading capacity including 24ton, 25ton, 28ton, 30ton, 32ton, etc.; Series including Fuwa type landing gears; Jost type landing gears; Holland type landing gears; Inside landing gears and trailer jacks. At same time landing gear parts such as T-foot, S-foot, A-foot, R-foot, , gear bars, L-plates, W-plates and other parts are available. Besides, full set of parts for OEM are also available.
ZF automatic transmission HP 602 C for city buses, line service buses and coaches ZF-ECOMAT 2 a modern transmission system for city buses, line service buses and coaches. The new CAN-capable (C) electronic shift modules (EST 46 / EST 47) provide the system with maximum possible shift comfort, safety, economy and service life. The Ecomat 2 range is designed for use in buses with a total weight not exceeding 28 t. Special Features Smooth moving off, no clutch wear Torque converter only operates when moving off Close ratio steps in planetary transmission Shift points are load and acceleration-dependent Consistent level of shift comfort with pressure regulation during gear-shifts Electronic control unit communicates with other electronic systems, such as CAN, SAE J 1939, etc. Improved safety due to integrated retarder with continuously variable control Increased road safety due to easy operation; operating errors are excluded Easy installation due to central wiring system Fast, straightforward system diagnosis on vehicle with new diagnostic system with menu logic Automatic Neutral at Bus Stop (NBS) as special option for city buses: automatically selects neutral when stationary We have total 400 Units
Displacement (ml): 193 Fuel efficiency (l/100km): 3.5 L*w*h (mm): 2600*1300*1640 Engine type : 1-cylinder, 4-stroke, water-cooled Rated power (kw/rpm): 10.3/7500 Ignition :cdi Transmission : 5-speed gear shift and return shift Max. Speed (km/h): 60 Net weight (kg): 320 Lubrication type : pressure spray Clutch : wet multiple Brake.(f/r) :disk/drum Start method : electric Fuel tank capacity(l):10 Tire type(f/r): 4.00-12/4.00-12 Container capacity : 8 Skd or cbu
Company has below material for sell in lower price. 1)331 j type (6.5x1.8) s.S. 2)331 c type(6.5x1.8) s.S. 3)dropper 165x11x0.3 open electrical s.S. 4)dropper 165x11x0.2 open electrical s.S. We are one of the reputed company for manufacturing healdwire and dropper. Please feel free to contact us for above sizes and other sizes as per your requirement.
We are supply of needle loom parts It give us great pleasure to introduce our selves as being one of the leading manufacturer, exporter of needle loom parts. Or parts are suitable for all type of textile machine like needle loom, tape machine. We are manufacturing parts from en-steel material and spring steel material. We can supply you the best quality parts at more economical rates and ready stock delivery. We are also supplying these parts to leading high speed needle loom machine manufacturers in all over world. We export the spareparts to africa, europe, usa, malaysia, bangladesh, germany etc. We are able to supply the spare parts for jakob muller, bonus, ky machines. " Please visit our website for more details of our company. Assuring you of our very best services at all the time.
We are manufacturer, importer and exporter of ceramic yarn thread guides for any type of textile machines. If you have any requirements please feel free to contact us
3 x 2, 3 x 7, 2 x 10 for plain loom 3 x 7, 3 x 10 for auto cimmco loom 2 x 12, 2 x 16 for ruti 'b' loom 2 x 16, 2 x 22 for ruti 'c' looom Sulzer, picanol, water jet, donier Air jet (tsuda coma & l-5000) etc Temple ring Plain nylon ring, rubber ring, pu ring Plain brass ring, nylon ring with pin Pin height 0. 15 mm 0. 75 mm 1. 50 mm 0. 15 mm 1. 25 mm Ring temple cover: For 3 x 7, 2 x 10 & all other type
2.7 inch screen 1/2 inch hd coms 140-degree wide-angle lens Humane settings: the optional front lens video, reversing camera recording, dual-lens video Feature sets: Languages: chinese simplified, chinese traditional, english Frequency: 50hz, 60hz After the lens input: pal, ntsc One is car¡¯s front camera that shoots the scene of car¡¯s front side. The other is back camera that Shoots the scene of car¡¯s back side. When you start the car, two cameras begin to work at the same time. When you shift to the reverse gear, thescreen will show backup camera display and the brightness of screen Will change with ambient light. When you shift to the reverse gear, the screen will show backup camera Display. At the moment, the interior camera stops working and the front camera and back camera start to work at the same time.
Weight (kg): 122 Gear shift: Forward High: 9.4 (km/h) Low: 4.5 (km/h) Reverse: High: 6.8 (km/h) Low: 3.2 (km/h) Handle rotation: 360O rotation at 12 position Handle height adjustment: 6 section height adjustment Clutch mode: Belt tenshioning pulley Engine: diesel engine air-cooled rated power 7.8.hp Max output is 9.hp Start mode: Hand Driving way: Gear shift Tilling depth (mm): 50-300 Tilling width (mm): 400-900 Tyre: 400-8/400-7. Dimension(L,W,H)mm: 1600,570,970 Weight (kg): 122.
Gear shift: Forward High : 9.4 (km/h) Low : 4.5 (km/h) Reverse High: 6.8 (km/h) Low : 3.2 (km/h) Handle rotation: 360O rotation at 12 position Handle height adjustment: 6 section height adjustment Clutch mode: Belt tenshioning pulley Engine: diesel engine air-cooled Rated power 5.6.hp Max output is 7.hp Start mode: Hand Driving way: Gear shift Tilling depth (mm): 50-300 Tilling width (mm): 400-900 Tyre: 400-8/400-7. Dimensions(L, W, H)mm£©: 1600, 570, 920 Weight (kg): 108 Packing: 200 units for 1, 40HQ container.
We honfe supplier specialized in supplying high-quality sulzer projectile loom parts for about 15 issors, slide piece, rh lever, rh opnener, centering blade, rh bar, weft end gripper, fas opener, screw, camplate, feeders es , projectile feeder plate, rh-openers, projectile feeder links es, rh-lever, upper & lower grippers, rh-bar, gripper spring, centering screw, guide pieces, spring rod, picking lever, slide block, precission cylindrical pin, brake band, rollers, camplate, centering blade, projectile lifter, connecting bar, rear brake saddle, feeder lever, gripper foot, expeller fork, selector, oil level glass witho-ring, chain pin, chain wheel, nylon bush, lifter, guide rails, rear, repeat gears, pfr-sensors, sensing head sfw, angle sensor wis, su-sensors, fa, ksa , tsn, sfb, ft flight sensors, weft end gripper, projectile boly, weft feeder, weft feeder bar, damping insert, clamping (ect) for sulzer pu, tw11, p7100, p7150, p7200, p7300 looms. Our company philosophy is "providing high quality product and efficient service"
Main Features 1.Parking brake: Disc brake; 2.Flexible and stable mesh sleeve shift; 3.Full hydraulic front-wheel steering with independent circuit; 4.Gearbox is 4X(2+1)Ã?2 shuttle shift,8 forward gears+ 4 reverse gears; 5.Rear semi-independent Power Output, with 6-spline 540/1000 r/min; 6.The use of a simple floor structure and an external divider is easy for maintenance; 7.Adopt YTO engine, Chinese famous diesel engine , big brand, quality assurance; 8.Rear three-point linkage, tire (front wheel+rear wheel) is 6.50-16+11.2-24 9.Planet-gear Final Transmission with small volume and large reduction ratio; 10.Planet-gear Final Transmission with small volume and large reduction ratio; 11.9-inch single or double action clutch & Semi-split lifter LT354 types of four wheels farm tractor ,full hydraulic steering;
, thrust bearings, roller bearings, cage bearings, power packs and amplifiers, propeller, water pump show out, housing, cup, impeller, washer, screw, nut, tube guide, o-ring, key, gasket, wear plate, water pump base, shim, bushing assembly, clip, shift shaft, insert, trim tab, shift spool, shift crank, cross pin, clutch dog, prop shaft, thrust ring, ball bearing, bearing carrier, tab washer, cover nut, thrust hub, lock washer, lock nut, slinger, drive shaft, anode, draining screw, shift cable tool, bearing retainer wrench, shift shaft bushing tool, pinion gear shimming tool, drive shaft adaptor, drive gear shimming tool, bearing carrier retainer wrench, pinion nut adaptor kit, hinge pin tool, engine alignment tool, trim cylinder, rear anchor pin, rod scraper, floating piston, springs, steel ball, shock piston, cylinder housing kit, plate seal, centering cone, gimbal bearing, clamp, spacer, cotter pin, reverse gear, screen!ketc. 43-18410a4 43-45814a5 43-55778a3 43-75325a3 2291010-01-24 2291010-02-24 853643-01-19t 853643-02-17t 853642-01-24t 853642-02-20t 853642-01-16t 853642-02-20t
