Power Diodes (Stud/Flat Type) Silicon Diodes are electronic components that conduct current in only one direction. In function, they are similar to one-way valves. Silicon Diodes, using semiconductor materials such as silicon are used as voltage regulators, signal rectifiers, oscillators and signal modulators / demodulators. Semiconductor diodes consist of a PN junction having two terminals, an anode (+) and a cathode (-). Current flows from the anode to the cathode within the diode. Diodes can be used as voltage regulators, tuning devices in RF tuned circuits, frequency multiplying devices in RF circuits, mixers in RF circuits, switching applications, or can be used to make logic decisions in digital circuits. Diodes can be sub-divided into six major categories: General Purpose Diodes (PN junction diodes) PIN Diodes Schottky Barrier Diodes Step-recovery Diodes Varactor Diodes Zener Diodes Laser Diodes PIN Diodes are three-layer Semiconductor Diodes consisting of an intrinsic layer separating heavily doped P and N layers. The charge stored in the intrinsic layer in conjunction with other Diode parameters determines the resistance of the Diode at RF and microwave frequencies. This resistance typically ranges from kilo ohms to less than 1 ohm for a given diode. PIN Diodes are typically used as switches or attenuator elements. Step-recovery Diodes employ graded doping where the doping level of the Semi conductive materials is reduced as the P/N junction is approached. This produces an abrupt turn-off time by allowing a very fast release of stored charge when switching from forward to reverse bias. It also allows a rapid re-establishment of forward current when switching from reverse to forward bias. These Diodes are used in very high frequency (VHF) and fast switching applications. Varactor Diodes are P/N junction Diodes that are designed to act as a voltage-controlled capacitance when operated under reverse bias. One characteristic of P/N junctions is inherent capacitance. When the junction is reverse biased, increasing the applied voltage will cause the depletion region to widen, thus increasing the effective distance between the two â??platesâ?? of the capacitor and decreasing the effective capacitance. By adjusting the doping gradient and junction width, the capacitance range can be controlled and changes can be applied using reverse voltage. Our Products Automatic Voltage Regulator (AVR) Automatic Transfer Switch (ATS) Power Diodes (Stud/Flat Type) Power Diodes (Capsule Type) Phase Control Thyristors (Stud/Flat Type) Phase Control Thyristors (Capsule Type) Inverter Grade Thyristors (Capsule Type) Power Modules Bridge Rectifier Modules Three Thyristor Welding Modules Bridge Rectifiers Moulded Rectifiers For Generators Mono Block Bridge Rectifiers (Single Phase) Mono Block Bridge Rectifiers (Three Phase) Welding Bridge Rectifiers Field Failure Relay (FFR) Generator Diodes
Copper WIRE SCRAP, (Millberry) 99.99% at a purity of 99.98% min. 99.99% Max. COPPER: 99.9% CARBON: 0.03% COBLET:
Copper WIRE SCRAP, (Millberry) 99.99% at a purity of 99.98% min. 99.99% Max. COPPER: 99.9% CARBON: 0.03% COBLET:
Cable Length ft 20 Color Black Side A Connector 1 HDMI MALE Side B Connector 1 DVID SINGLE LINK MALE Product Warranty Period Worldwide Lifetime limited warranty Application Consumer Application as PC TV Monitor Tablet
LV-01 Gate Valve +Basic Design : API 600 / BS 1414 / API 6D +Body Wall Thickness : API 600(Heavy Wall) / API 603(Light Wall), ASME B16.34 +Pressure Rating : ASME B16 34 +Face To Face : ASME B16.10 / ISO 5752 / BS2080 +End Connection : - ASME B16.5(Raised Face) - ASME B16.25(Butt Weld) - ASME B16.34(Ring Joint) +Body Bore Size: ASME B16.34 +Flange Size : - ASME B16.5 for 24 in & below size / ASME B16.47 Series "A" or MSS-SP-44(For 26 in & above size) - API 605 Series "B"(For 26 in & above size) +Inspection And Testing : API 598 / Sour Service(NACE MR 0175 or MR 0103) + Surface Quality Visual Method : MSS-SP-55 + Finishes For Contact Faces of Flanges : ASME B16.5 or MSS-SP-6 + Marking Standard : MSS-SP-25 +OPTION * Drain Plug(ASME B16.34 / MSS-SP-45), Threads(ASME B1.20.1) * Locking Device * Live Loading(Belleville Spring) * Jacketed(Semi & Full) * By-pass Piping & Valve(MSS-SP-45)
Plastic butterfly valve high pressure u-PVC Ball Valve Plastic pvc big size irrigation system dripper water flow control Liquid Butterfly Valve Plastic Socket Thread butterfly handle PVC Ball Valve Plastioc Baffle Type Cartridge Farm PVC Foot Valve Plastic irrigation PVC double Union Ball Valve Plastic butterfly valve high pressure u-PVC Ball Valve Plastic Red one-way Handle White Body water drip system garden uPVC outdoor Valve Plastic u-PVC octagonal new design Ball Valve JIS BS ANSI DN standard Plastic long handle high quality u-PVC white ball valve plastic italia design france spain morocco portugal south africa olive valve orchard valve PVC single union ball valve plastic female male thread ABS Angle Valve BS ANSI JIS DIN red handle coffee body socket u-PVC plumbing Ball Valve Plastic PVC Male and Female threaded plumbing valve Plastic irrigation big size water pump spring type PVC Foot Valve plastic irrigation water system U-PVC Single union ball valve Plastic ABS handle PVC valve body True union ball valve Plastioc agriculture irrigation system middle east water tank pipe Male and Female thread union ball MF valve Plastic Socket Connector irrigation green handle black body PVC Garden Ball Valve plastic PVC agricultural irrigation system Ball Valve plastic swing foot valve pvc check ball valve pump valve Male to Female Thread Plastic brand-new material PVC Octagonal Ball Valve Plastic u-PVC new design octagonal combined Ball Valve plastic UPVC spring non-return check valve plastic Blue handle White body water system u-PVC Ball Valvein or Thread compact Plastic Red one-way Handle gray Body uPVC compact Ball Valve Plastic Socket Connector irrigation dark blue PVC Garden compact BSpt Ball Valve Plastic long handle high quality u-PVC gray compact ball valve factory Plastic ABS handle PVC valve body True union irrigation valve plastic female male thread ABS chrome plating Angle Valve plastic manufacturer Male Female Thread brand-new material PVC Octagonal Ball Valve Plastic factory Red one-way Handle White color Body irrigation water system uPVC Ball Valve Plastic Socket Thread butterfly handle 15mm 20m 25mm 32mm 40mm 50mm 65mm 80mm 100mm PVC Ball Valve Plastic long handle high quality u-PVC white color 20mm 25mm 32mm 40mm 50mm 63mm 75mm 90mm 110mm ball valve plastic factory supplies Male to Female Thread Plastic brand-new material PVC Octagonal Ball Valve plastic male and female thread ABS ceramic chip Angle Valve factory Plastic ABS handle PVC valve body single union irrigation valve Body: U-PVC Handle: ABS Ball: U-PVC Sealing washer: PTFE Size: 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4" End connector: Thread or Socket Handle Type: Butterfly Standards: ANSI BS DIN JIS Characteristic: Light Environmental Durable Media: water corrosive liquid Use: Agriculture irrigation Garden Construction Petroleum chemical industry ETC.
SuperKlean's single valve hot or cold water station was specifically designed to provide individual outlets of hot or cold water. The unit uses two connection nuts for superior flexibility during installation. SuperKlean's inlet & outlet have the same dimensions as most of our competitors' stations. Our stations come with a mounting plate for easy behind the unit cleanup and hose rack for easy user access to the hose. Principal Parts, Material &Ratings Inlet / Outlet Diameter: 3/4" NPT Station Body: Brass or 300 Series Stainless Steel Globe Style Valve: Brass or 300 Series Stainless Steel Ball Valve: Bronze or 300 Series Stainless Steel Maximum Globe Valve Pressure: 150 PSI Maximum Ball Valve Pressure: 600 PSI WOG Maximum Temperature: 200° F (93° C) Weight: 10 Lbs. (6000M) & 8 Lbs. (6000BM)
Alloy 20 forged fittings are well known for their outstanding mechanical qualities at both low and high temperatures. They are very resistant to general corrosion, crevice corrosion, and pitting. This feature can be maintained in a variety of media, including chlorides, acidic mediums, and a variety of acid-containing solutions. Itâ??s important to remember that the alloy 20 material will only keep its corrosion-resistant characteristics if itâ??s kept in optimal metallurgical and clean conditions. Sulfuric acid resistance is excellent in Alloy 20 forged fittings. They are also resistant to Phosphoric acid, nitric acid, and aqueous salt solutions. When chloride stress corrosion cracking is a concern, Alloy 20 forged fittings are a good choice since they resist pitting and crevice corrosion. In chloride ion-containing situations, caution should be exercised because the rate of corrosion can dramatically increase. Chemical processing, petrochemical and refining, marine, pharmaceutical, and food processing are just a few of the industries that employ Alloy 20 forged fittings. Storage tanks, mixing tanks, agitators, pump and valve parts, food processing equipment, fasteners, and fittings are examples of end-use applications. According to ASME, applications are limited to a maximum temperature of 1000 F. It's also crucial to figure out whether the required corrosion resistance can be attained in the particular environment.
Lot of 20 Stryker Single Port Manifold REF 700-15 DISCLAIMER: The item is in its original condition and no alterations have been made to the item. The item has been properly stored and handled, following the manufacturers recommendations. The item comes with the accessories specifically mentioned in the description or shown in the pictures. This item is not a food or medical product that has expired. This item does not appear to be damaged or mishandled. To the best of seller’s knowledge the item has not been recalled. FDA REGULATION AND CERTIFICATION: · The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, do not bid on this item unless you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item. · If you have questions about legal obligations regarding sales of medical devices, you should consult with the FDA's Center for Devices and Radiological Health:
* The API 600 Gate Valves is exceptionally sturdy, rugged, and durable, with a reputation for quality, integrity, and long service. * They are designed for tight sealing and ease of operation. The valves are available flanged & butt-weld ends in pressure rating from ASME Class 150 to Class 2500, and in a variety of materials of construction. * Gate Valves are of flexible wedge design, outside screw and yoke, and bolted-bonnet construction. The valves conform to API 600. Main features * Bolted body-bonnet design,seal welded & Valves with pressure seal bonnet * Bellows-sealed Gate and Globe valves available * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
* The API BS 1868 series of Swing Check Valves is exceptionally sturdy, rugged and durable, with a reputation for quality, integrity, and long service. * They are designed for tight sealing and ease of operation. The valves are available flanged & butt-weld ends in pressure rating from ASME Class 150 to Class 2500, and in a variety of materials of construction. * Check Valves are of swing-type and bolted-cover construction. They conform to BS 1868 and also meet the general requirements of API 600, including shell wall thickness. Main features * Bolted body-cover design, seal welded & Valves with pressure seal cover * Bolted body-cover joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on the stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss, and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
The ASME B16.34 Swing Check, and Y Type Swing Check Valves feature a pressure seal bonnet design for high-pressure services. These valves are extensively used in high pressure and high-temperature steam, oil, gas, chemical, and water applications in thermal power plants, fertilizer plants, petrochemical plants, and refineries. These valves are available in butt weld ends in pressure ratings of Classes 900, 1500 and 2500, and come in carbon steel and alloy steel construction.
The BS 1873 Globe Valves is exceptionally sturdy, rugged and durable, with a reputation for quality, integrity and long service. They are designed for tight sealing and ease of operation. The valves are available flanged & butt-weld ends in pressure rating from ASME Class 150 to Class 2500, and in a variety of materials of construction. Globe Valves feature a ball-type disc, outside screw-and-yoke and bolted-bonnet construction. They conform to BS 1873 and also meet the general requirements of API 600, including shell wall thickness and stuffing box dimensions. Main features * Bolted body-bonnet design,seal welded & Valves with pressure seal bonnet * Bellows-sealed Globe valves available * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
Size : 1/2" To 12" (15MM To 300MM) Class/Pressure: #150 To #1500 End Connection : Flange, Buttweld, Socket Weld , NPT, Etc Design Standard : API 6D, ISO 17292, etc Testing Standard : API 598, API 607, ISO 5208, etc Body Material : Carbon Steel,Alloy Steel, Stainless Steel,
Globe Valves are extensively used through-out the Refineries,Hydrocarbon,Energy and process & the power industries. Size: 2" up to 24" (DN 50 up to DN 600) Pressure Rating: ASME 150# to 2500# Materials: Carbon Steels, Low Temperature Carbon Steel, Martensitic Steels, Austenitic Stainless Steel, Duplex Stainless Steels, Super Duplex Stainless Steels, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel, Titanium Alloy & Carbon Steel with Internal Corrosion Resistant Alloy (CRA) Overlay Design Standard: BS 1873, API 623 Pressure / Temperature Rating: ASME B 16.34 Test (Inspection) Standard: API 598,ISO 5208,BS 6364 Construction Details: Bolted Bonnet / Pressure Seal Bonnet, OS & Y Type Rising Stem End Connection: Flanged,Butt-Weld Operator / Actuator: Handwheel Gear, Actuator (Pneumatic, Hydraulic, Electro-Hydraulic and Electric Motorised) Cryogenic Service: Globe Valves can be designed in a special version suitable for cryogenic service. In this case, all the materials and technical features are designed to withstand minimum design temperature required by the Customer, down to Cryogenic -196'C. If required by the customer, specific Cryogenic Tests are performed to verify the behaviour of production valves in terms of valve torque, sealing capability, emissions vs the ambient
Size : 1/2" To 24" (15MM To 600MM) Class/Pressure: #150 To #4500 End Connection : Flange, Buttweld, Socket Weld , NPT, Etc Design Standard : API 6D, ISO 14313, etc Testing Standard : API 6D, API 598, API 607, API 6FA, etc Body Material : Carbon Steel,Alloy Steel, Stainless Steel, Special Material Also Available
* The Bolted Bonnet Gate Valve is exceptionally sturdy, rugged, and durable, with a reputation for quality, integrity, and long service. * They are designed for tight sealing and ease of operation. The valves are available flanged & butt-weld ends in pressure rating from ASME Class 150 to Class 2500, and in a variety of materials of construction. * Gate Valves are of flexible wedge design, outside screw and yoke, and bolted-bonnet construction. The valves conform to API 600. Main features * Bolted body-bonnet design,seal welded & Valves with pressure seal bonnet * Bellows-sealed Gate and Globe valves available * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
* The Gear Box Operated Gate Valve is exceptionally sturdy, rugged, and durable, with a reputation for quality, integrity, and long service. * They are designed for tight sealing and ease of operation. The valves are available flanged & butt-weld ends in pressure rating from ASME Class 150 to Class 2500, and in a variety of materials of construction. * Gate Valves are of flexible wedge design, outside screw and yoke, and bolted-bonnet construction. The valves conform to API 600. Main features * Bolted body-bonnet design,seal welded & Valves with pressure seal bonnet * Bellows-sealed Gate and Globe valves available * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
* The Pressure Seal Bonnet Gate Valve is exceptionally sturdy, rugged, and durable, with a reputation for quality, integrity, and long service. * They are designed for tight sealing and ease of operation. The valves are available flanged & butt-weld ends in pressure rating from ASME Class 150 to Class 2500, and in a variety of materials of construction. * Gate Valves are of flexible wedge design, outside screw and yoke, and bolted-bonnet construction. The valves conform to API 600. Main features * Bolted body-bonnet design,seal welded & Valves with pressure seal bonnet * Bellows-sealed Gate and Globe valves available * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
* The SQK Flexible Wedge Gate Valve is exceptionally sturdy, rugged, and durable, with a reputation for quality, integrity, and long service. * They are designed for tight sealing and ease of operation. The valves are available flanged & butt-weld ends in pressure rating from ASME Class 150 to Class 2500, and in a variety of materials of construction. * Gate Valves are of flexible wedge design, outside screw and yoke, and bolted-bonnet construction. The valves conform to API 600. Main features * Bolted body-bonnet design,seal welded & Valves with pressure seal bonnet * Bellows-sealed Gate and Globe valves available * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
