A burner made with CI body, has a Primary and Secondary air ports, supplied wit Air Butterfly valves, Burner block, Precise control oil Valve (SOV) as a Package. Burner is used in the applications, where Fuel will be Diesel, LPG, Natural Gas, Producer gas etc., This burner is specially designed to avoid localized Heating. It is designed to give 100% Combustion efficiency even with High carbon oil. Advantages : Fuel Efficient by Better atomization Uniform heat transfer, 10% savings will be possible by interchanging with any make burner. Optional Accessories : Preheated combustion air upto temperature of 350?C (Max) for fuel saving upto 40%.
A cubical shell drier, which is a customized design based on the applications, temperature requirement for these applications vary from 100C to 300C. Driers are also designed with Direct and Indirect type Driers. Drier is lined with Refractory and Insulation brick/ Glass wool insulations to hold the Temperature up to 600 C. Driers will have two chambers in case of indirect type drier. The chambers are firing and Heating Chambers. If in case of Direct type drier, the re circulation fan must be used for the forced heat transfer. Advantages : Our Furnaces are designed in such a way to reduce the Fuel Consumption. Our furnaces are lined with both refractory bricks and Ceramic fibre modules, in such a way to pass the flue Gas around the material to be heated, enabling high conduction convection and Radiation heat transfer. Combustion/Heating Equipments are designed to meet the requirements of furnace and Heat transfer rate. Burner will be positioned inclined to an angle, so that the flame/flue skips on the surface of the material. Better heat transfer rate through circulation and Re-circulation. Our furnaces are designed for skin temperature of 65C (Maximum). Optional accessories : Pre heating the scrap before charging can be done. Recuperator to pass the combustion air into the burner at a temperature of 150C (minimum) for fuel saving upto 40%.
The features of the walking beam heating furnace: (1)Walking beam reheating furnace is the most widely used in foundry field for metal ingots, billets, tubes and pipes. (2)Walking beam heating furnace is make up with moving parts and fixed parts. (3)We can produce all kinds of the walking beam heating furnace, such as walking beam furnace, walking bottom furnace and walking beam bottom combined furnace. (4)If the billet section is bigger than 120x120mm2, you can adopt the walking beam reheating furnace. (5)If the billet section is smaller than 100x100mm2, you can adopt the walking bottom reheating furnace. (6)We can design the furnaces according to your special requirements. Negotiable.
Bogie type furnace, the structure of furnace is that there is a portable bogie on the bottom . Before heating, charging the bogie outside the furnace, the heating pieces put on the special iron, then the bogie will be pulled into the furnace by tractor, then will be pulled out for unloading, the heating work piece will be lift by the crane onto the metal forming equipment for processing. Our company produces these types of the bogie type furnace: (1)High temperature series (furnace temperature 0-1200 degree), bogie type furnace (5 tons - 100 tons) is suitable for high alloy steel for high temperature normalizing, annealing, quenching and tempering and roll. (2)Middle temperature series (furnace temperature 0 -950 degree), bogie type furnace (5 tons - 100 tons) used in general metal parts for normalizing, annealing in the air. (3)Low temperature series (furnace temperature 0 -750 degree), bogie type furnace(5 tons - 200 tons) apply to steel parts tempering, low temperature annealing and cores drying. Standard export package in pallet, and we can negotiable.
Technical data: Chamber size: O.D.205xI.D.190xH340mm Max. temperature: 1200 oC Working temperature: 1100 oC Temperature control: 30 segments programmable and PID auto control Heating elements: Fe-Cr-Al-Mo wire Furnace chamber: ceramic fiber Furnace structure: double shell with fan cooling Thermocouple: K type Heating rate: ¿Q20 oC/min. Temperature: ¡§ª+1 oC Max. vacuum: -0.1MPa Power: 3KW. Plastic paper inside, Polyfoam filled, Wooden box outside.
1.Production Name: Medium Frequency Induction Furnace 2.Production Description: 1)Medium Frequency Induction Furnace for melting 2)Full digital control system with high accuracy 3) Melting steel, iron,stainless steel,copper,aluminium 4)0.15-350 tons capacity 5) Constant power output, speedy melting, good electricity saving efficiency. 3.Usage: Medium Frequency Induction Furnace Mainly used in melting steel, iron, copper, aluminum and alloy, is with high melting efficiency, good electricity saving effect, good metal component uniformity, less burning loss, speedy temperature rise, easy control of temperature, is suitable to all kinds of metal melting. 4.Characters and Advantages: 1) Constant power output, speedy melting, good electricity saving efficiency. 2) Zero-voltage sweep-frequency style start, adapts to requirement of frequently start. 3) Comprehensive protection functions, such as overcurrency protection, overvoltage protection, current-limiting protection, voltage-limiting, water-break protection, and default protection, equipment runs reliably under premise of melting speed guarantee. 4) Easy to operate, suitable for all casting process. 5. Package: Plywood cases and nude. Plywood Box.
Electric Heating Conduction Oil Furnace Details Working Principle For Qilian electric heat conduction oil furnace (also known as heat conduction oil heater), the electric heater is directly inserted into the organic carrier (heat conduction oil) for direct heating. A circulating pump is used to create liquid-phase circulation of heat conduction oil, thus, to transfer the heat to one or several pieces of heat using equipment. After unloaded in the heat using equipment, the heat conduction oil will return to the heater via the circulating pump, again to absorb heat, and transfer the heat to the heat using equipment. This process is repeated again and again, realizing continuous transfer of heat. As a result, the temperature of objects being heated rises, and heating requirements are fulfilled. Composition Qilian electric heat conduction oil furnace system is composed of an explosion-proof electric heater, an organic heat carrier furnace, a heat exchanger (configurable), a control cabinet, a hot oil pump, and an expansion slot. The user only needs to connect the equipment to a power supply, and arrange medium inlet and outlet pipes and electrical interfaces before use. Application Scope Qilian electric heat conduction oil furnace adopts a digital display temperature controller, and has functions of over temperature alarm, low oil level alarm and over pressure alarm. This product is a type of high-efficiency energy-saving heating equipment for chemical, petroleum, machinery, printing and dyeing, foodstuff, marine, textile, and film industry, etc. Characteristics 1. Low Operating Pressure Liquid phase heat transfer can reach a higher operating temperature under lower operating pressure; saturated vapor pressure of heat carrier is 70 to 80 times lower than that of water; and its general operating pressure is 0.3mp 2. High Heating Temperature Heating temperature of the electric heat conduction oil furnace may reach 280heating-up temperature is automatically controlled, realizing high sensitivity and stable heat supply. 3. Safe and Reliable Our electric heat conduction oil furnace is equipped with a perfect operating control and safety monitoring device, so it is easy to operate, safe, and reliable. 4. Environmental Friendly Design The electric heat conduction oil furnace is a new type of electric heating system. Electricity is used instead of coal, which reduces investment outlay and is free from contamination; meanwhile, heat conduction oil furnace, with short heating time and high thermal efficiency, is more efficient and economical.
Horizontal Gas/Oil fired industrial steam boiler features: •Adopt numerical control, include Automatic Mode, Manual Mode, Timing Mode, Error Recording, password protection,etc. •Be provided with automatic blow down system (Independent patent technology) •Automatic Scale alarm(Independent patent technology), overpressure protection devices ensure the safety of the boiler •Easy maintenance, front door of smoke box adopt articulated joint which is convenient to be open, the cleaning of close-by flue tubes become easy too. •Safe and reliable, before leave the factory, all the boiler have to pass series of strict tests to ensure the safety and reliability of combustion and auto control devices Parameter: Type Mode Rated evaporation (t/h) Rated pressure (Mpa) Rated evaporation temperature (°C) Diesel consumption (Kg/H) Natural gas consumption (Nm3/h) Weight (T) horizontal central reverse flame WNS0.5-0.8-YQ 0.5 0.8 175 34.4 41.1 3.735 WNS0.7-0.8-YQ 0.7 48.2 57.5 5.502 WNS1.0-1.0-YQ 1.0 68.8 82.1 5.68 WNS2.0-1.0-YQ 2.0 1.0 184 137 164.3 8.255 WNS1.5-1.0-YQ 1.5 103 123.15 9.885 WNS2-1.0-YQ 2.0 137 164.3 11.14 horizontal three Pass WNS1.5-1.25-YQ 1.5 103 123.15 9.689 WNS2.0-1.25-YQ 2.0 137 164.3 11.6 WNS2.5-1.25-YQ 2.5 1.25 194 172 205.5 15.0 WNS3.0-1.25-YQ 3.0 206 246.3 17.12. Standard pickings( well wrapped in plastic clothes packing with wooden case).
Industrial burners
M1700 type (d/c): Dia3/6, dia4/9, dia6/12, dia9/18, dia12/24 M1800 type (d/c): Dia3/6, dia4/9, dia6/12, dia9/18, dia12/24 Plastic paper inside, Polyfoam filled, Wooden box outside
Main Specifications: Inside Chamber Size dia60x300mm(diameter2.5" x 12") Standard Working Temperature 1650 . C ( continuous ) Maximum Working Temperature 1700 . C ( < 3 hrs) Temperature Control 30 steps programmable and PID automatic control Heating Rate 0~10 . C / min (suggestion: =< 10 . C) Temperature Accuracy +1 . C Heating Element MoSi2 heating elements Working Voltage AC 220V Single Phase 60/50 Hz (or according to your requirement) Max. Power 5 KW Net Weight 150 Kg Plastic paper inside, Polyfoam filled, Wooden box outside.
Main Specifications: Inside Chamber Size 200 x 200 x 200 mm (8"x8"x8", 8 Liter) Standard Working Temperature 1500oC ( continuous ) Maximum Working Temperature 1600oC ( < 3 hrs) Furnace Atmosphere Nitrogen, Argon and other inert gases Temperature Control 30 steps programmable and PID automatic control Heating Rate 0~ 10.C/ min (suggestion: =< 10.C ) Temperature Accuracy +/- 1 .C Furnace structure double shell with fan cooling Heating Element MoSi2 heating elements Thermocouple B type Working Voltage AC 380V Three Phases 60/50 Hz (or according to your requirement) Max. Power 10KW Outside Size 550 x 540 x 820 mm Net Weight 230 Kg Plastic paper inside, Polyfoam filled, Wooden box outside.
Heatsink (DP-11Industrial Heatsink) Overall Dimension:165.5X161.5X58.5mm Material:Al Fin+Heatpipes+Cu Base Weight:335g. Industry packing.
Configuration accompanied the machine Air agitator, vacuum pump (including cooling water pump that is started in the same step, water tank), electric control system, electric heating system, 5 layers silica rubber bags, furnace body and electric load/unload section. Parameter : 1.Dimension (L*W*H):3750*2250*2000 mm 2.MAX. area of glass to be processed: 3100*1800 mm 5 layers silica rubber bags (its size: 3400*1950mm) 3.Thickness: 3-15mm 4.Power: 43KW 5.N.W: 2.5T 6.Layer:5 layers (for circulating)
Glass heat bending furnace (NEW type)-FY-W-A This machine have top and bottom heating chambers, the top chamber is for heating and bottom chamber is for fixing shapes. Its temperature is controlled by imported PLC. The platform is elevated by air cylinder. It is easy to be operated. It takes about 5 hours to finish one time. It is suitable for heat bending glass, such as, glass furniture, glass coffee table, glass sanitary right corner counter top and decorative project glass, etc. Parameter: 1.thickness : 3-25mm 2.power : 380V/26kw 3.dimension : 2700*1441*1320mm 4.inner size : 2300*1100*700mm 5.N.W : 1.2T 6.Speed: heating time 2-2.5 hours cooling time 3 hours
1. Loading capacity - 400 kg to 1200 kg gross 2. Heating - electric heater type/ gas type 3. Quenching - oil quenching or molten salt 4. Atmosphere - nitrogen methanol, endo gas As per the equipment
1. Capacity - fromm 100 kg/batch to 2000kg/batch 2. Media - steel shots ( cast or cut wire) 3. Dust collector- standard cloth bag or cassete type 4. M/c type - thumb blast, table type, t- rail type, hanger type, cont. Blast type etc. Depend on machine size, export quality wood packing
Hollow silver statue and indian god, elephant, and ather animalls in light weight silver electro formed well in finishing.All articals r 92.5silver, 999silver, avelable on request. Standared plastic paking.
Technical parameter The rated power of the area of hot zoneª1450f¦ The ways of mark the dimensionªgc d/l/m/d D --hot zone diameter ffd-- cold end diameter M --cold end lengthff n-- the length of spray aluminium zero L-- hot zone lengthff l --total length Our sic heating elements adopt special technics and can save you energy. Silicon carbide (sic) heating element is a non-metal electric heating element made from sic as its main raw materials. It has some specific properties, such as low expansion coefficient, little deformation, stable chemical property, long service life, easy installation and maintenance, etc. Used in the industries of glass, ceramic, machinery, analysis test, semiconductor, science & research and so on.
Ground granulated blast furnace slag 1. Fineness (m2 /kg): 370. 2. Soundness le-chatelier expansion (mm) : nil. 3. Initial setting time (min) Not less than opc:220. 4. Insoluble residue(%):0.05 5. Magnesia content (%):9.5 6.Sulphide sulphar(%):0.60 7. Sulphite content (%):0.10 8. Loss on ignition (%):0.30 9. Manganese content (%):0.06 10. Chloride content(%):0.003 11. Moisture content(%):0.005 12. Glass content(%):94 13. Compressive strength (n/mm2): After 7 days34.0 After 28 days53.0 14. Chemical moduli A). Cao + mgo + sio2 :84.0 B). Cao + mgo /sio2 :1.30 C). Cao/sio2 :1.05. Tonnes packed in i tonne or i.5 jumbo bags.
