The model of the slurry pump is selected based on the flow head provided on site. After the model is determined, the caliber of the slurry pump is also determined. However, the pipelines on site are not designed according to the caliber of the slurry pump. If the size is large What will happen if a large-diameter slurry pump is equipped with a small-diameter pipeline? Let's take a look. Many users think that this can increase the actual lift of the slurry pump. In fact, the actual lift of the slurry pump is the total lift minus the loss lift. When the slurry pump model is determined, the total head is certain; the loss of head mainly comes from the pipeline resistance. The smaller the pipe diameter, the greater the resistance, so the loss of head is greater. Therefore, after reducing the pipe diameter, the actual head of the water pump is not only It cannot be increased, but will decrease, resulting in a decrease in water pump efficiency. In the same way, when a small-diameter water pump uses a large water pipe to pump water, the actual head of the water pump will not be reduced. On the contrary, the loss of head will be reduced due to the reduced resistance of the pipeline, so that the actual head will be increased. Some users also believe that when a small-diameter water pump uses a large water pipe to pump water, the motor load will inevitably be greatly increased. As everyone knows, the liquid pressure is only related to the head and has nothing to do with the cross-sectional area of the water pipe. As long as the head is turned on, the size of the impeller of the water pump remains unchanged. No matter how large the pipe diameter is, the pressure acting on the impeller is certain. However, as the pipe diameter increases, the water flow resistance will decrease, resulting in an increase in flow rate and an appropriate increase in power consumption. But as long as it is within the rated head range, the water pump can work normally no matter how the pipe diameter is increased, and it can also reduce pipeline losses and improve water pump efficiency. If you want to know more about slurry pumps, please feel free to call us! Shijiazhuang Pansto Pump Industry is a manufacturer of slurry pumps in Shijiazhuang. It mainly designs, manufactures and sells slurry pumps and accessories. Mainly engaged in mud pumps, submersible pumps, foam pumps, desulfurization pumps and many other series. Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
The impeller of the sand pump is the main accessory of the entire slurry pump. The flow rate and lift of the pump and the size of the passing particles are directly related to it. In addition to the diameter and width of the impeller, another important parameter is the number of blades. The most common sand pump impellers we have are 3-piece, 4-piece, and 5-piece impellers. The number of blades has a great influence on the flow capacity of the pump. The smaller the number of blades, the larger the particle passing diameter and the stronger the passing performance. We often use it for pumping sand. The slurry contains relatively large pebbles, so a three-blade impeller is usually used. Because there are fewer blades and the greater the spacing between them, the larger the particles that pass through. However, the number of blades is not the only factor that determines the passage of large particles. It is also related to other factors. We should not only look at the number of blades, but also the overall structure of the pump. The number of impeller blades is also related to the efficiency of the pump. The greater the number, the higher the efficiency. The efficiency of large particle sand pumps is generally lower than other pumps with multiple blades. Relatively speaking, if there are no large particles, you can choose 4-blade and 5-blade impellers, which can achieve better efficiency and save costs. If you want to know more about slurry pump accessories, please call us to consult the water pump industry! Shijiazhuang Pansto Pump Industry is a manufacturer of slurry pumps in Shijiazhuang. It mainly designs, manufactures and sells slurry pumps and accessories. Mainly engaged in mud pumps, submersible pumps, foam pumps, desulfurization pumps and many other series. Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
120 m3 CAPACITY - MOUNTAIN MATERIAL - CRUSHING AND SCREENING PLANT (CRUSHER) FOR SALE FROM THE MANUFACTURER YOU DON'T NEED TO LOOK FOR A SECONDHAND CRUSHING - SCREENING - WASHING PLANT TO BE ECONOMICAL, DON'T MESS WITH SOMEONE ELSE'S SCRAP... WE OFFER YOU THE OPPORTUNITY TO PURCHASE HIGH QUALITY, LONG-LASTING, CRUSHING-SCREENING-WASHING PLANTS AT AFFORDABLE PRICES. WE ARE AVAILABLE 24/7 WITH OUR ENTIRE TEAM TO OFFER THE HIGHEST QUALITY PRODUCTS AND SOLUTIONS TO OUR CUSTOMERS IN 5 CONTINENTS AND 52 DIFFERENT COUNTRIES. MOREOVER, WE GIVE A 2-YEAR UNCONDITIONAL WARRANTY AGAINST MANUFACTURING DEFECTS TO ALL OUR PRODUCTS BY RELYING ON OUR MANUFACTURING QUALITY. THE PRICE WRITTEN IN THE ADVERTISEMENT IS REPRESENTATIONAL. YOU CAN CONTACT OUR SALES REPRESENTATIVE TO GET A SPECIAL PRICE OFFER ACCORDING TO YOUR NEEDS. THE MAIN REASONS TO CHOOSE OUR COMPANY WHY MEGA EXPORT & IMPORT Easy communication in preferred language On-time production - delivery and assembly Secure trade with fixed price guarantee 24/7 online support with experienced staff for exports Online monitoring of the production process Online tracking of the shipment process Free infrastructure preparation project and test production Easy trade with leasing and letter of credit WHY MEGA CRUSHING - SCREENING - WASHING PLANTS Quality product - affordable price Low energy consumption - minimum cost Low infrastructure and installation costs Easy to use automation program in any language Electric panels that can operate in different energies Economic shipment with disassembled design Low maintenance cost and spare parts readily available in every country Ability to be easily dismantled and moved to another area SPECIAL WARRANTY AND SERVICE Unconditional 2-year mechanical warranty against manufacturing defects Economical spare parts sales at the end of the warranty period Possibility to extend the warranty period to 5 years with a price difference International validity of warranty commitments Instant fault detection with remote connection to the facility Minimum 10-year warehouse stock availability guarantee for each part In case of malfunctions requiring service, 48 hours intervention to our domestic facilities and maximum 72 to 120 hours intervention to our facilities abroad. CRUSHERS AND PLANTS WE PRODUCE CRUSHING PLANTS WITH CONE CRUSHER CRUSHING PLANTS WITH VERTICAL SHAFT CRUSHER CRUSHING PLANTS WITH HAMMER CRUSHER CRUSHING PLANTS WITH JAW CRUSHER CRUSHING PLANTS WITH TERTIARY CRUSHER For the Crushing and Screening Plants in the capacity you prefer, the Infrastructure Project that needs to be built in the area where it be established is given free of charge by our company. Please visit our website to watch promotional videos and get more detailed information.
XC701 DC36V Motor Controller for Fountain Pumping System Let water dance to music. XC701 motor controller is engineered for (music) fountain pumping system. Performance and reliability of had been verified and approved by clients and market. After several iterations, XC701 motor controller can adapt to various application circumstance. itâ??s one of the best sellers in XC motor control product family. Demand on fountain pump controller could be diverse, we provide bespoke service for customers. If you have any specific requirement, we help you achieve it. This motor controller for fountain pumping system comes with characteristics: Specification: Model: XC701 Working Voltage: DC13.5-30.5V Rated Current: 31.5A Working Temp: -45-85â?? Humidity: 95% Max Dimension: 71*68*26mm Protection: Undervoltage protection, over voltage protection, overcurrent short circuit protection, over-temperature protection, motor stall protection Protocol: DMX512 protocol XC Motor Control has been specializing in motor control since 2011, we have considerable expertise in enhancing motor control. The potent combination of hardware and advanced software can keep your device working at optimal. Have a try, you are worth a better solution.
900ml Hydrogen breathing machine advange: 1. Imported American DuPont platinum N117 proton membrane has a longer life than traditional membranes. 2.Medical, food-grade electrolyzer, more safer. 3.Aluminum alloy shell, more advanced, strong and durable. 4.Super large touch screen, ultra-clear display, real-time display of 99.99% hydrogen concentration, hydrogen flow and working hours. 5.Four automatic detection and alarm functions: Lack of water, over heating, high water level, water quality TDS Alarms, more convenient. 6.The interior is compact and reasonably designed, small in size, light in weight, equipped with universal wheels, and a pull handle, which is convenient for the elderly to move. 7.With child lock function, you don't have to worry about children touching it, making it safer to use. 8.One-button start, timing function, low-noise design, quiet sleep, time-saving.
Compact Concrete Batching Plant. CAPACiTY FROM 30M3/H TO 180M3/H WiTH SILOS BRAND : FABO SITUATION : NEW
Technical Parameters Travel of X and Y Axes: 800x1200 mm; Maximum cutting thickness/ Maximum height of the part: 700 mm; Maximum Work piece weight: 1000 kg; Wire diameter: Standard 0.18 mm mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 985x1580 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 160 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150 �¼s; Approx. Machine size (LxWxH): 2600x2400x1800 mm; Approx. Machine weight: 4500 kg; Approx. Machine control cabinet size: 670x630x1800 mm; Approx. Machine control cabinet weight: 200 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 â??. ;
Technical Parameters : Travel of X and Y Axes: 500x630 mm; Maximum cutting thickness/ Maximum height of the part: 600 mm; Maximum Work piece weight: 700 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 600x860x600 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 150 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150; Approx. Machine size (LxWxH): 2000x1950x1750 mm; Approx. Machine weight: 2540 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 ;
Technical Parameters : Travel of X and Y Axes: 800x630 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1130x9500x300 mm; Maximum Work piece weight: 750 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 2200x1650x1910 mm; Approx. Machine weight: 2980 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters: Travel of X and Y Axes: 630x500 mm; Maximum cutting thickness: 350 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 m mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1020x640x350 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 2180 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters Travel of X and Y Axes: 500x400 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 850x540x300 mm; Maximum Work piece weight: 450 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 1790 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters Travel of X and Y Axes: 400x320 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 620x480x300 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1700x1300x2160 mm; Approx. Machine weight: 1480 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 800x630 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1130x9500x300 mm; Maximum Work piece weight: 750 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM or HL SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 2200x1650x1910 mm; Approx. Machine weight: 3000 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 630x500 mm; Maximum cutting thickness: 350 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 m mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1020x640x350 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM or HL SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 2200 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 500x400 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 850x540x300 mm; Maximum Work piece weight: 450 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM or HL SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 1800 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 400x320 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 620x480x300 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1700x1300x2160 mm; Approx. Machine weight: 1500 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters Travel of X and Y Axes: 1200x1500 mm; Maximum cutting thickness: 1000 mm; Maximum Work piece weight: 3500 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1300x1900x1000 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM or HL SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 4200x3600x2300 mm; Approx. Machine weight: 10000 kg; Approx. Machine control cabinet size: 1200x800x800 mm; Approx. Machine control cabinet weight: 150 kg.
Technical Parameters Travel of X and Y Axes: 1000x1200 mm; Maximum cutting thickness: Standard: 800 (Can be adjustable) mm; Maximum Work piece weight: 2000 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1010Ã??1500 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 100 square mm/min; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 1.2 KVA; Approx. Machine size (LxWxH): 3100x2500x2300 mm; Approx. Machine weight: 5000 kg; Approx. Machine control cabinet size: 1200x800x800 mm; Approx. Machine control cabinet weight: 150 kg.
Technical Parameters Travel of X and Y Axes: 630x800 mm; Maximum cutting thickness: 600/800 mm; Maximum Work piece weight: 1000 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 680x1080x600 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 2265x1865x1980 mm; Approx. Machine weight: 3500 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg.
DK7745 Technical Parameters Travel of X and Y Axes: 450x550 mm; Maximum cutting thickness: 460 mm; Maximum Work piece weight: 750 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 500x750x460 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1865x1350x1900 mm; Approx. Machine weight: 1250 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg.
