Product; Scrap Pet Bottle .Pet Plastic Bottle Grade: 100% PET Color ratio: Clear 100% individually & Green 100% Appearance: Bottles Impurity : No Caps, rings, or labels PVC : Less than 0.01% Water Content : Less than 0.01% moisture Packing; Pressed in Bales. Baled and Loaded in 40' HC! 115cm X 75Cm X115 cm Commodity: PET Bottle.
Applications: Designed for handling condensate in the steam and water circuit systems of the thermal power stations that burn organic fuel. May be also used to transfer water in heating plants and water supply systems. Performance of the Pump: Capacity, Q = 80 m3/h, Head, H = 155 m, Speed of rotation, 2940 rpm, NPSHr = 1.6 m The pump as a component of the pump unit is an electrically driven horizontal multistage ring-section centrifugal pump between bearings, with single flow impeller arrangement. The suction casing, delivery casing and stage casings are bolted together with tie bolts to form a pump casing. The suction nozzle integrally cast with the suction casing is located horizontally at side (radially to the pump centerline). The discharge nozzle integrally cast with the delivery casing is oriented vertically upwards. The pump casing is supported at the bottom with feet integrally cast with the suction and delivery casings. The pumping unit alignment is maintained during its operation due to dowelling the delivery casing to the baseplate, whilst the other end of the pump can slide axially thus allowing for free expansion of static components.
The Company belongs to a group that has been operating in the goldsmith and jewellery markets for over three generations, and is specialized in the promotion and distribution of jewellery for the medium to high level market. Traditional craftsmanship coexists with the most recent technology to place the Company’s Product/Design area on the cutting edge for jewellery design. All products are entirely manufactured in Italy and have long been synonymous with quality and authenticity. Constant innovation, creativity and design of its creations have always constituted the strong points of the Company. It represents a trendy brand which readily responds to the evolution of its customers and constantly strives for originality in style, to transform the simple pleasure of wearing jewellery into an ever unique and enticing experience. The Company’s collections are meant to inspire the best emotions in people wearing its jewels. Every collections includes golden and silver and platinum necklaces, bracelets, earrings, rings, pendants and in some cases also watches. The Company is looking for representatives or agents as well as for direct dealers interested in its production. Target countries: Bulgaria, Portugal, Spain.
KEY RING BRACELET NECKLACE FOR MORE DETAILED INFORMATION AND PICTURES YOU CAN CONTACT US
Specifications: Engine power: 3 kw Reductor engine. System: reductor +hydraulic Controlled by plc automation System 100% digital Programming Air supply required (4 bars) Safe and fast production with strong body structure Materials that will be used for ring: from 12x12 square, 100 diameter and 120 mm. Diameter ring materials that will be used for twist: square 12, 14 maximum 150 cm. Materials that will be used for cone: 12, 14, 16, 18, 20 Cone capacity average 1000 pcs/ 24 hours Dimension(length*width*height): 200 x80 x130 cm Weight: 800 kg
1. Full range volume from 0.3-150ml 2. Luer slip, Luer lock, Eccentric, Catheter, Toomey tip styles 3. W/needle, W/O needle; Latex/Latex free/O-ring/TEP piste 4. Special design to prevent plunger slipping out 5. Package, Needle, Color, cap, etc... per different requirement Transaction Details Only for your reference, contact us for detailed information Price : The specific price can be negotiated Payment terms: FOB Shanghai 30% T/T in advance, 70% against BL copy
Reference: KH-1393 Capacity: 600 ml Made of stainless steel - Designed with various proportions for cocktails and drinks. - Just rotate the housing to see the recipe. - The shaker features a ring with drink names â?? simply choose the desired one and rotate the housing to select its name. When you do so, the list of ingredients will be revealed â?? the exact amounts in millilitres and the order in which they should be placed in the shaker. - Capacity: 600ml - The filter prevents ice and pieces of fruit from passing to the glass - All parts are easy to clean; wash by hand with water and washing-up liquid and always wipe dry
Brand Spare Part Description Wartsila / 34sg Cylinder Liner Wartsila / 50 Connecting Rod Wartsila / 50 Counterweight Wartsila / 50 Exhaust Compensator Wartsila / 50 Camshaft Piece (Counter-cl) Wartsila / 32 Piston Complete (Crown+skirt+gudgeon Pin) Wartsila / 32sg Cylinder Liner Wartsila / 34 Big - End (+ Shä°m) Wartsila / 50 Piston Complete (Crown+skirt) Wartsila / 32df Injection Valve Yoke Wartsila / 32df Big-end Vasa 32 Piston Ring Set Vasa 32 Exhaust Valve Guide Wartsila / 34sg Bracket For Air Vent System Wartsila / 32 Small End Bearing Wartsila / 32 Hyraulic Jack For Con. Rod Mak / 43 Fuel Pipe Seal Kit (193376845) Mak / 43 Fuel Pump Seat Kit (193466836) Mak / 43 Cooling Collar (193376850) Mak / 25 Small-end Bearing Mak / 452 Valve Guide Mak / 25 Inlet Valve Guide Mak / 25 Exhaust Valve Guide Mak Stud Mak / 20 Rockerarm Bush Mak / 43 Camshaft Bearing Mak Bush Mak / 25 Exhaust Valve Mak / 32 Cylinder Head Stud Mak / 43 Fuel Pipe Seal Kit (190376308) Mak / 43 Fuel Pump Seal Lit (193376848) Mak / 32 Rockerarm Daihatsu / Ps26 Connecting Rod Bearing Daihatsu / Ps26 Main Bearing Daihatsu Small End Bearing Daihatsu C.w Pump Mouth Ring Daihatsu Inlet Seat Daihatsu T/c Exh. Outlet Gasket Daihatsu T/c Inlet Gasket Daihatsu Muhtelä°f O-ring Ve Gasketler Daihatsu / De 23 Idle Gear Daihatsu / De 23 Muhtelä°f O-ring Ve Gasketler Daihatsu / Ps26h Stud Yanmar Rockerarm Kapaä?i Yanmar Main Bearing Yanmar Crankpin Bearing Yanmar Crankpin Bearing Yanmar Crankpin Bearing Yanmar Crankpin Bearing Yanmar Barrel/plunger Yanmar Bush Yanmar Rrod Bolt Yanmar / 6n21 A Hfo Limit Switch Yanmar Impeller Yanmar Thrust Bearing Man / 32-40 Exhaust Seat Man / 32-40 Inlet Seat Man Turbo Vtr 304 A-32 T/c Bearing Pielstick / 2.5 Exhaust Valve (For Gas Engine) Pielstick / 2.5 Barrel - Plunger (For Gas Engine)
With an exquisite taste and pleasant aroma all its own, Pine Forest Honey will carry back you to the pine forests of the Aegean. Blended with great care, this honey is guaranteed by experts to be of unparalleled Balparmak quality. The journey of Pine Forest Honey to your plate begins with the Marchelina Hellenica insect that inhabits the pine trees of the Aegean. This insect deposits a sugary liquid that it cannot digest on pine trees. Honeybees gather this up and process it with enzymes secreted from their bodies. Any connoisseur of flavor must get a taste of pine honey, 90% of which is produced in Turkey Aegean Region. Balparmak provides reliable solutions, delivering honey in drums, equipped with fully removable, open-head steel top-ends. Drums are produced with the latest production technology andtested in accordance with UN regulations to guarantee optimum protection for honey. Drums are one size, cylindirical and filled with 295 kg, net honey. The removable top-end is firmed to the body, by a closing ring with an elastic washer in between. Drums�¢?? and caps�¢?? material specifications and license for production are fully concordent with the universal specifications under TS EN ISO 9001:2000 and (EN 10130 and EN 10131), Quality Management System. Interior surfaces are coated with Epoxy Phenolic internal foodstuff lacquer. Exterior of the drums are finished with oven-drying enamel, with Balparmak logo printing by silk screening on body.Drums are 100 % leakproofness tested.
Wellhead drilling spool 11" x 3k - 13 5/8" x 3koil well api 16a driling spool 11" x 3k - 13 5/8" x 3k overview of the drilling spool 11" x 3k - 13 5/8" x 3k the 11" x 3k - 13 5/8" x 3k drilling spool is used to connect with bop for oilfield drilling work.The wellhead drilling spool is made of alloy steel and heat-treated. It is used on the oil and gas well which is with a pressure of less than 105mpa. It is tested according to api 16a specificationbefore shipping to be used safely.The 11" x 3k - 13 5/8" x 3k spool applies to drilling high pressure oil and gas well, the connecting of the by passage of the spool with the valves and pipes will play not only a role of blowout and choking , but also a role of connecting the bop with the wellhead. installation and maintenance of wellhead drilling spool* being used when connecting with the bop and the casing head.*.The steel ring grove should be cleaned before installation.*.Tighten studs averagely of connecting the spool with the bop. specification of the wellhead drilling spool 11" x 3k top flangebottom flange11"2000psi (279.4mm14mpa)11"2000psi (279.4mm14mpa)11"2000psi (279.4mm14mpa)13-5/8"2000psi (346.1mm14mpa)11"3000psi (279.4mm21mpa)11"3000psi (279.4mm21mpa)11"3000psi (279.4mm21mpa)13-5/8"2000psi (346.1mm14mpa)11"3000psi (279.4mm21mpa)13-5/8"3000psi (346.1mm21mpa)11"5000psi (279.4mm35mpa)13-5/8"3000psi (346.1mm21mpa) wellhead drilling spool 11" x 3k - 13 5/8" x 3koil well api 16a driling spool 11" x 3k - 13 5/8" x 3k
Description This item is a practical and multi functional smartwatch, which adopts quality shell and silicone band. It is not only a watch which can display the time and date, but also can act as a GPS to mark its location. It also has SOS/ Anti-drop off alarm function. Specially designed for children and students to wear. Feature - Equipped with GPS global positioning system, it will show its location at any time to monitor the child position. - It supports micro SIM card so it supports making calls at any time, and it features a SOS button which is designed for emergency. It will ring the reserved phone number until it gets through. - You can set some creation areas for your kids on the APP maps, once kids leave these areas, the APP will alarm to remind you automatically. - The waistband is made of soft flexible silicone, easy to be folded to secure kids wirst without squeezing and breaking. - Note: There is no SIM card on the case so you need to take the battery out to settle the SIM card and this is not a difficult thing if you have some basic tools. Specification - Color: Black - Wristband Material: Silicone - Watch Size: 52x28mm/2.0x1.1inch - Cellular Band: GSM 850/900/1800/1900MHz - CPU: MTK 6261 - Display: 0.96inch - Resolution: 96x64 - Speaker: 8©/0.5W - MIC: Built-in mic - Positioning System: GPS and LBS - Telephone: Support - SMS Alert: SupportNeed to install software) - Remote Monitoring: SupportNeed to install software) - SOS Alarm: Support - Remote Debugging: Support - Acceleration Sensor: Support - Low Power Management: Support - Net Weight:39g - Battery Capacity: 400mAh - Battery Types: Li-polymer 3.7V - Talking Time: 2h - Standby Time: 3days
Applications: designed for pumping condensed waste steam from stationary steam turbines and heating steam condensate (drain water) from heat exchangers in the thermal power stations that burn organic fuel. May be also used to transfer water in heating plants and water supply systems. Design: aksv series pump units consist of a centrifugal pump and an induction motor mounted on the motor stool. They are connected by means of a rubber-bushed (pin-and-bushing) flexible coupling. The pumps are electrically driven vertically suspended, can diffuser, single-stage (ksv 125-55) or multistage centrifugal pumps with inducer and single flow impeller arrangement (with all the impellers facing the same way). An outer casing (barrel) and an inner casing (withdrawable element or cartridge) are the major pump components. The barrel is a construction made of steel plate by complete welding process, which integrates a suction chamber (in the form of a can) and a discharge chamber (the discharge head proper). Pump support feet and weld-end suction and discharge nozzles are welded to the barrel. The inner casing (a rotating assembly) of ring-section type comprises a bare rotor, a shaft seal bearings, stage casings with built-in diffusers and a delivery cover. The design of pump shaft seal chamber provides for both housing a mechanical seal (-t) and packing the stuffing box (-s). The shaft of the pump make КсВ 125-140-3М is sealed only by means of packed gland.
Electric cart SPECIFICATIONS: Dimensions: Total Length mm 930 Width mm. 650 Height mm. 1070 Floor Length mm 870 Width mm. Ground Clearance 620 mm. 330 Weights: Total kg including batteries. 77.90 Batteries kg. 13 each. x 2 Motor: Permanent magnet motor with electric 200 W - rpm 120 - 24 V electro 24VDC 2Nm. Voltage and batteries: no Two 12V batteries 32 A C5 sealed gel - series connection, without maintenance. External charger 24 v - 8 ampere - Electronic microprocessor - Power supply 220 v. Brakes: Electric brake block engine, listing in the event of power failure. braking on deceleration (engine braking) enhanced in the calibration of the parameters of the controller. Speed and Capacity (performance with the vehicle in perfect working order on flat surface: Max 5 Km / h + / - 10% Max 250 kg. terms and 100kg. slope of 15%. Maximum flow rate is considered with the load distributed uniformly on the floor. Tires: 2 wheels rubber tires mounted on rims with pneumatic 3.00-4 6-ply roofing. 2 wheels 200x50 diameter core polypropylene gray synthetic rubber ring mounted on swivel mounts. Frame: Tubular steel and Fe 37 powder-coated polyester for outdoor Ral 6018 Spare parts and tools for the maintenance and repair: Original spare parts and tools for maintenance and repair are provided directly to order from Italy Bigà spa. Sound level values: less than 70 dB (A)
5 - Foot sheet chariot 5.1 Dimensions: Total length 930 mm Width 650 mm Height 1070 mm Plan Length Width mm 870 mm 620 mm Ground clearance 330 5.2 Weights: Total 77.90 kg including batteries Batteries 13 kg each. x 2 5.3 Motor: Permanent magnet motor with electric 200 W - rpm from 120 to 24 V electro 2Nm 24VDC. 5.4Voltaggio and batteries: N. 2 x 32 A 12 V sealed gel in C5 - series connection, maintenance-free. External charger 24 V - 8 amp - Electronic microprocessor - Power supply 220 V 5.5 Brakes: Electric brake to the engine block, insertion of a power failure. Braking on deceleration (engine braking) enhanced in the setting of parameters control unit. 5.6 Speed and Capacity (performance of the vehicle in perfect working flat route: Maximum speed in 6 seconds of continuous accelerated 5 km / h + / - 10% Max capacity 250 kg and 100kg in terms of gradient of 15%. The maximum flow is considered with uniformly distributed load on the floor. 5.7 Tyres: 2 rubber wheels mounted on wheels with pneumatic 3.00-4 6-ply roofing. 2 wheels 200x50 core diameter polypropylene ring mounted on gray synthetic rubber supports swivel. 5.8 Structure: Tubular and sheet S 235 JR polyester powder coated RAL 6018 external 5.9 Spare parts and tools for maintenance and repair: The original spare parts and tools for maintenance and repair are provided directly Order by Biga spa Italy. 5.10 Values sound level: less than 70 dB (A) 5.11 Environmental conditions: temperature + 5 + 40 C Humidity 50%.
MAHI MAHI FILLET - Scientific Name : Coryphaena Hippurus - Common Name : Mahi, Dolphin - Origin : PERU - Form : IWP Frozen -Sizes: 1-3 lb, 3-5lb, 5 up -Loading: asap full FCL
MAHI MAHI G&G - Scientific Name : Coryphaena Hippurus - Common Name : Mahi, Dolphin - Origin : PERU, Sizes: 2-4KG -Loading: asap full FCL
Product Description: The automatic pick and place machine TP400V-II is a cost-effective equipment in the SMT industry. It is able to fabricate a variety of components by the integrated vacuum nozzle. The machine can mount SMD chip components above 0402, SOICs, PLCCs, QFP and ICs. The Vision System is compatable with QFP ICs with a pitch of 0.5mm. Beside the round reference, also square square formed and ring hole pads can be recognized as mark point. Features: 1. Automatic Mount by control of software. 2. Quick PROTEL data import or manual input. 3. Visual + machinery positioning. 4. Visual programming system can identify the reference point automatically to improve the production efficiency and accuracy. 5. The visual programming system can produce X, Y coordinates of all components automatically after confirmed the basic reference points and to complete the mounting process. 6. Unique optical prism and high-definition industrial cameras for placing high-precision components. 7. Equipped with a high-precision quadrate guide rail and smooth gliding arm for improving mounting accuracy. 8. Air suspended head for pick- and place-process. 9. Automatic nozzle replacement system. Optional: 1. Automatic feeder 2. IC disc 3. Automatic PCB transmission system Main parts: 1. DC servo motor driving system: It uses loop DC servo motor driving system for a high precision repeating accuracy and stability. 2. Vision centering system: Vision centering system can mount 0.5mm pitch QFP ICs. 3. No-contact flying centering system: Flying centering system can mount most of SMD components including: 0402, SOICs，PLCCs & QFP ICs. 4. Flexible reference point system (RPS): In addition to the standard round reference point, also a square formed and ring formed PCB pad with a whole can be identified as a reference point. 5. All-purpose automatic feeder: The TP400V-II has 8mm, 12mm, 16mm, 24mm feeders which you can choose to install. 6. Flexible tray-type station: The TP400V can equip 2 trays which helps to mount bulk components under the semi-auto mode. 7. CAD/ Protel data transfer: Besides studying the component coordinate by Camera or keyboard input, you can choose the CAD transfer software WCAD to transfer the PCB’s CAD into pick and place data. 8. Buffering nozzle: Buffering nozzle can adjust the pressure automatically according to different components height to avoid damage due to different component heights or programming errors. It is suitable for various types of pick and place ceramic components and ceramic circuit boards. Technical Parameter: Type: TP400V-II (V: industrial camera at bottom) Max printing size: 400×350mm Max moving range: 400×630mm Z axis max moving range: 70mm Typical mounting speed: 2000-2800cph Max mounting speed: 3500cph Mounting accuracy: ±0.05mm Component available: SMD components > 0402 and SOICs、PLCCs、QFP ICs < 38mm Positioning method: Visual positioning Programming method: Video study/ keyboards input/ data import Driving way: Y-axis uses industrial synchronous belt drive, X-axis uses imported high precision lead screw. Automatic Feeder: 8mm, 12mm, 16mm, 24mm feeder Feeder Number: 1. Place 72 pieces of 8MM feeder CFTA-08S, 36 pieces at the front and back side. 2. Place 60 pieces of 8MM feeder GFTA-08S, 30 pieces at the front and back side. PCB board input system: Automatic (Standard configuration) Automatic Nozzle changing system: Automatic (Standard configuration) IC tray number: 2 Operation system: WINDOWS XP Compressed air: 80psi (0.5Mpa) Power supply: 220V, 50Hz, 3kw Weight: 310kg Dimension: 1280×1410×750mm
Our company, a Taiwan funded enterprise, has been specialized maunufactuering screw nut machine and hardware for 20 years. Dongguan factory was founded in 1994. All the machine parts are mainly imported from Taiwan And the 17B6S detail can see in the below, 1. Technical Parameter MODEL: SW-NF 17B 6S NUT FORMER MACHINE FORGING STATION 6S 7S CUT-OF DIA (MAX) 18mm CUT-OFF LENGTHE (MAX) 30 KICK-OUTENGTH (MAX) 120 mm CENTER DISTANCE BETWEEN DIES (MM) 70 RAM STROKE (MM) 100mm FORGING POWER (TON) 1200 ton PRODUCT SIZE (INCH) 1/4 7/16 inch OUTPUT PCS/MINUTE 180 MAIN MOTOR (HP) Â 30 PUMP MOTOR (HP) 1/1 LUBRICANT (GALLON) 300 APPROX.WT (TON) 11 FLOOR AREA REQUIED (L*W*H) 3.5m* 2.15m* 1.7m 2. Application: Not only used for manufacturing Normal nuts, like Hex nut, Flanged nut, Square nut, Weld nut, Cap nut, Rivet nut, Extra thick nut, but also Motorcycle link pin, Oil plug screw, Pipe joint, Chain roller, Bearing roller, Bearing ring, Expansion anchor, Bushing sleeve, Bicycle and Motorcycle shaped spare parts, Auto spare parts, shaped nuts and various shaped pieces of shaped and non-standard items, ect, which are widely applicable in the fields of construction, metallurgy, furniture, electronics and electric appliance, automotive, aviation and other industries. 3. Main Features: No.1 The machine body and main sliding block are processed through stress relieving after being forged to prevent from deformation and ensure durable mechanical stabolity. No.2 Machine body of high alloy steel imported is prossed through quenching treatment to ensure lasting resistance to wearing. No.3 Eash cam is precisely designed with computer and made in CNC process center to ensure correct and smooth cam common normal. No.4 Applying air compressor clutch,smooth and steady start current brake,realization of inching, single stroke and continuous running, besides inching way,main sliding block will stop at the utmost point ehen the machine stops every time to provide max. operation space.
The pipe is manufactured from 100% virgin unplasticized polyvinyl chloride compound (PVC-U). No re-worked material is used. The pipe is produced under an ISO 9001-2000 Quality System. Duzgunler Plastic pipes are produced in a range of pressure ratings 4, 6, 10 and 16 Bar. Duzgunler Plastic pipes are produced in a range of nominal pressure (PN) at 20°C. The appropriate derating factors should be applied for working pressures when subjected to higher temperatures. The nominal outside diameters and nominal wall thickness are based on an overall service (design) coefficient C=2,5 from 50 mm.to 90 mm. and C= 2 from 110 to 355. Duzgunler Plastic pipe is used in a wide range of applications, such as: * Irrigation systems main/sub-mains. * Chemical industrial processes. * Pressurized water supply (city town, industrial, home, commercial.) * Drainage/sewage applications. * General services, domestic water, A/C drainage. * Ducting, electrical, telecommunication. * Industrial process plants oil/gas/petrochemical. * Desalination processes, brine disposal, mineral water Features of Duzgunler Plastic U-PVC pipes: * Fully compliant with TS 274 EN 1452 and ISO standards. * Resistant to a wide range of chemicals and corrosion. * High Impact Resistance * Quality assured and tested to the strict specifications of the standard for dimension compliance, impact resistance, burst pressure, flattening & joint tightness. * Smooth internal bore for low friction losses. * Compatible with the full range of PVC-U Pressure fittings. * Long service life under a wide range of conditions. * Will not support combustion. There are 4 types according to their pressure resistance: PN4 PN6 PN10 Pn16 Available Diameters (mm) : 50 63 75 90 110 125 140 160 200 225 250 280 315 355 400 Technical Features: Raw Material: U-PVC Standard: TS 274 EN 1452 Dimension: Pipes produced in ranging from Ø 50 mm. dia. up to Ø 400 mm. dia. Normally supplied in 6 m length Others can be supplied on request. Connection: rubber ring joint for all size Technical Features: -Gravity: 1350 < p < 1460 kg/m² -Opaque: max. % 0,2 -Deformation heat: 80 C -Resistance to diklormetan: Resistant -Quantity of vinilcloridmonome: less than 1ppm -Resistance of int. Pressure: Two times of nom pressure -Resistance to stroke: TIR < % 10 Unpacked.
Torsional Vibration Dampers (TVD) CORA TVD's stand high loads as our premium quality rubber compounds maximize their damping properties. Decoupled Dampers or DDS (Double Damping System Dampers) Decouplers are made up of a TVD assembled with a torsional coupling, so-called â??isolatorâ??. DDS special design helps to eliminate crankshaft vibrations at low the frequency through the crankshaft isolator rubber while the TVD reduces the torsional vibrations at high frequency inside the crankshaft. Viscous Dampers In VISCOUS dampers, the viscous oil layer placed between the inertia ring and pulley body runs the energy dissipation and converts it into heat. This technology can dampen a wide range of crankshaft natural frequencies from different orders. We hold two patents on innovative construction solutions for viscous dampers.
