Applications: Designed for handling condensate in the steam and water circuit systems of the thermal power stations that burn organic fuel. May be also used to transfer water in heating plants and water supply systems. Performance of the Pump: Capacity, Q = 80 m3/h, Head, H = 155 m, Speed of rotation, 2940 rpm, NPSHr = 1.6 m The pump as a component of the pump unit is an electrically driven horizontal multistage ring-section centrifugal pump between bearings, with single flow impeller arrangement. The suction casing, delivery casing and stage casings are bolted together with tie bolts to form a pump casing. The suction nozzle integrally cast with the suction casing is located horizontally at side (radially to the pump centerline). The discharge nozzle integrally cast with the delivery casing is oriented vertically upwards. The pump casing is supported at the bottom with feet integrally cast with the suction and delivery casings. The pumping unit alignment is maintained during its operation due to dowelling the delivery casing to the baseplate, whilst the other end of the pump can slide axially thus allowing for free expansion of static components.
D 2500-62-2-S UKhL4 ( 2500-62-2- 4) make Between-Bearings Double Flow Axially Split Pumps Pump parameters: Capacity, Q = 2500 m3/hr, Head, H = 62 m, Speed of rotation 980 RPM, NPSHr = 6 m/ Applications: Designed for the supply of water to industrial plants and communities. They are used also for agricultural land irrigation and drainage. Design: The pump units shall be rigidly anchored to the foundation, and piping shall be rigidly connected to the pumps. The pumps are electrically driven horizontal, foot-mounted, single-stage, axially split volute casing centrifugal pumps with a double entry radial impeller. The pump casing is a locating part of the pumps, which incorporates a lower and an upper casing halves bolted together by means of studs. Pump shaft sealing is by means of packed glands. Sense of rotation of shaft in all the pumps is counterclockwise, if viewed from the drive side. Upon the Customer request, the pumps may be supplied with a rotor for reverse rotation.
Coal phenol C6H5OH Cas:108-95-2 30 tons(Availability)\2000$\kg min order 20 tons
Centrifugal,screw.
Stainless steel swivel fitting for self-service car wash pantograph
Paper bags and paper sack, adhesives.
Ziplock tape for vacuum packaging lollipop stick, pe pneumatic lance.
Stainless Steel Washstand
Stainless steel car mat clip
Product Description - Offering best drill collars for drilling operations in oil and gas extraction (Slick and spiral Drill Collars, with slip and elevator recesses according to customer's request). Product origin - Sumy, Ukraine - UA Key Specifications/Special Features - Certification and standards: API Spec 7-1, API Spec 7-2, Q1 and ISO 9001, ISO 29001 and NS-1 Slick and spiral Drill Collars, with slip and elevator recesses according to customer's request Steel grade: AISI 4145H mod, fully heat treated as per API Specification At customer request it is possible to produce Drill Collars from non-magnetic and H2S resistant steel grades Technical parameters OD: from 79,4 mm (3 1/8) up to 279,4 mm (11) Length: 8300 mm, 9145 mm and 9450 mm, at customer request the length can vary from 6500 mm up to 12500 mm Standard API and double shouldered thread connections are made with stress relieved elements, cold rolled and phosphated, and equipped with pressed steel or heavy duty plastic thread protectors at both ends Hard banding of ARNCO 350XT, Castolin OTW 13CF, tungsten carbide Ultimate tensile strength: min 140 000/965 ksi/mPa, Yield strength: min 110,000/758 ksi/mPa, Elongation: 15%, Impact strength: min 48J, Brinell hardness: min 285-341 HB Mechanical properties guaranteed to 1 below steel surface.
Product Description - Our products include Slick and Spiral exclusively forged HWDP (not welded or hot rolled material). Product origin - Sumy, Ukraine - UA Key Specifications/Special Features - Certification and standards: API Spec 7-1, API Spec 7-2, Q1 and ISO 9001, ISO 29001 and NS-1 Slick and Spiral exclusively forged HWDP (not welded or hot rolled material) Type I / Type II with one or two central upsets, Type III Spiral with one central upset Steel grade: AISI 4145H mod, fully heat treated as per API Specification At customer request it is possible to produce HWDP from non-magnetic and H2S resistant steel grades Technical parameters OD: from 88,9 mm (3 1/2) up to 168,3 mm (6 5/8) Standard length: 8300 mm, 9450 mm, 12250 mm, 12500 mm Standard API and double shouldered thread connections are made with stress relieved elements, cold rolled and phosphated, and equipped with pressed steel or heavy duty plastic thread protectors at both ends Hard banding of ARNCO 350XT, Castolin OTW 13CF, tungsten carbide Ultimate tensile strength: min 140 000/965 ksi/mPa, Yield strength: min 110,000/758 ksi/mPa, Elongation: 15%, Impact strength: min 48J, Brinell hardness: min 285-341 HB Mechanical properties guaranteed to 1below steel surface.
Product Description - Square and Hexagonal Kellys are types of Rotary Kellys our company is offering as a product of a highest quality. Product origin - Sumy, Ukraine - UA Key Specifications/Special Features - Certification and standards: API Spec 7-1, API Spec 7-2, Q1 and ISO 9001, ISO 29001 and NS-1 Square and Hexagonal Kelly Steel grade: AISI 4145H mod, fully heat treated as per API Specification Technical parameters Size between facets: from 76,2 mm (3) up to 155,0 mm (6 1/8) Standard overall length: 9000 mm - 16460 mm Standard API thread connections are made with stress relieved elements, cold rolled and phosphated, and equipped with pressed steel or heavy duty plastic thread protectors both ends Ultimate tensile strength: min 140 000/965 ksi/mPa, Yield strength: min 110,000/758 ksi/mPa, Elongation: 15%, Impact strength: min 48J, Brinell hardness: min 285-341 HB Mechanical properties guaranteed to 1 below steel surface. Minimum Order Size and Packaging details - At customer request Kellies are delivered in individual scabbards to protect the work surface from mechanical damage during transportation
Product Description - We're offering forged bars of different types including: Square forged bars; Round forged bars; Forged bars with variable cross-section. Product origin - Sumy, Ukraine - UA Key Specifications/Special Features - Technical parameters: OD 129 - 390 mm, length as agreed with the customer Steel Grades: Carbon steel Alloy and high alloy steel Stainless (chromium and nickel) steel Heat Treatment: Quenching and Tempering Annealing Normalization Minimum Order Size and Packaging details - (min order 12-14 t)
Drill collars, - heavy weight drill pipes, - rotary kellys, subs / pup joints, - pipe billets (solid bars), - pipe billets (bored bars), steel forgings / forged bars, continuous casting blooms, ingots.
The reseller company is looking for Buyers on Nitrile Examination Gloves (Non-Sterile Powder-Free), Brand-VGLOVE, Vietnam, Size S, M, L, XL; Quality: FDA 510k; CE, ISO, EN-455 1/2/3, EN 374 1/2/4/5; Packing: 100 pieces/box/ 10 boxes/carton; Total Quantity: From 50 000 (two 40-foot containers) to 1 million boxes per month; Terms of Delivery/Price: FOB: Ho Chi Minh Port / 8,60 USD; CIF: country EC airport/8, 80 EUR; Delivery term: shipment within 10 days after exhibiting L/c; Payment terms: 100% L/C; If you are interested, please contact us for more information. Contact person: Nikolay
The buyer is interested in receiving offers for the following RFQ: Product name: SOLVENT R5; Specifications: methanol content - 44.5%, isopropanol content - 55.5%, impurities - no more than 0.3%; MOQ: 300 tons; Delivery terms: CIF; Destination port: Romania, Baltic States; Payment terms: T/T; Contact person: Nick
Gun holder 600mm. Stainless steel
These cases using for manufacturing vending machines. The lowest price for this product type is 1035 USD.
Manufacturing of stainless steel and black sheet metal enclosures.
The pantograph is equipped with special rotating elements: metal tube / base