Latex Sealant is a homogenous pasty mixture without any foreign substances with dispersibility of about 20 v 30 mcm. The viscosity of 90% water solution, viscosimeter nozzle diameter of about 4 mm, is about 50 v 80 sec. PH level is not less than 10. Mass part of dry matter is about 54%. drums, casks
Stretch films rubbish bags.
Compostable eco friendly bags and film.Shipping
PVC films.
Sodium Dichloroisocyanurate Dihydrate (SDIC·2H2O) pixels
Sodium Dichloroisocyanurate (SDIC)
Trisodium Phosphate (TSP
Light Cycle Oil (LCO) is a diesel boiling range product from Fluid Catalytic Cracking Units (FCCUs). FCCU is responsible for the production of petrol, LPG and Light Cycle Oil (LCO). There are various ways of economically upgrading LCO, which include hydrotreating, high pressure hydrocracking for full conversion of LCO into Naphtha and a more optimized partial conversion hydrocracking process. It can be used in susch industries as Agrochemical, Crude Oil, Petrochemicals, Petroleum Products.
Technical (construction) Film.
Polyethylene pipes (designed for water supply, gas pipelines, technical and protection applications) and polyethylene films (designed for agriculture, construction and packaging).
Used Tyres Scrap
Sodium Tripolyphosphate (STPP)
Trichloroisocyanuric Acid (TCCA)
Garbage bags, construction films, t-shirt bags.
Soft drinks, energy drinks, confectionery, snacks, grocery, household products and chemicals, kids and personal hygiene.
Polymer film packaging materials (high and low pressure polyethylene hdpe / ldpe, polypropylene and composite packaging pe / pp / pet / c).
Boats.
Mustard seeds, millet, wick, coriander, oil seeds, mustard powder, flax, oilseed, radish, rapeseed, safflower, seeds of forage grass, sainfoin, lupins, forage feed crops, corn, peas, lupine, vetch, oats, sorghum, legumes, beans, soybeans, beans.
Applications: Designed for delivering treated water (feedwater) at the pumping temperature of up to 438K (165C) into the fossil-fueled stationary boilers with absolute steam pressure of maximum 13.7 MPa (140 kgf/cm2). Capacity, Q = 100 m3/h, Head, H = 580 m, Speed of rotation, 2970 rpm, NPSHr = 4 m. The pump units shall be rigidly anchored to the foundation, and piping shall be also rigidly connected to the pumps. The pumps are motor-driven horizontal, centreline-supported, between-bearings multistage ring-section centrifugal pumps with single flow impeller arrangement. The pump casing comprises a suction casing, a delivery casing and a set of stage casings, which are concentrically aligned with respect to each other on rabbeted fits and are bolted together with tie bolts. Diffusers are built in the stage casings and delivery casing. The suction and delivery casings have flanged suction and discharge pump nozzles respectively, which are oriented vertically to the top. The rotor axial thrust is automatically balanced with a balance disc. In order to ensure a normal functioning of the balancing device, its chamber is to be communicated with the suction pipeline. A bearing end cover, fitted in the non-drive side bearing housing, has a shaft position indicator for sight control of the wear of balancing device surfaces and for restraining rotor axial displacements towards the delivery side. The pump rotor is carried by the plain bearings with ring lubrication. The design of pump shaft seal chambers provides both for housing mechanical seals and for packing the stuffing boxes, which are to fed with cooling liquid. Sense of rotation of shaft in all the pumps is counterclockwise, if viewed from the drive side.
Applications: Designed for the supply of water to industrial plants and communities. They are used also for agricultural land irrigation and drainage. Capacity, Q = 400 m3/h, Head, H = 105 m, Speed of rotation, 1470 rpm, NPSHr = 4.5 m The pump units shall be rigidly anchored to the foundation, and piping shall be rigidly connected to the pumps. The TsN type pumps are centrifugal, horizontal, spiral with horizontal split casing, with transfer channels, two- or four-stage, with single-entry impellers symmetrically arranged on the shaft according to type BB1 or BB3 API 610. The pump rotor is supported by grease-lubricated roller bearings. Shaft seals are gland packing. The pump casing is the main part of the pumps, which consists of the lower and upper half of the casing, connected together by studs.
