Flooring- a low viscosity, modified -aliphatic polyamines epoxy curing agent. It has been designed for use in solvent-less coatings and leveling floorings where excellent flow, good adhesion and high gloss films are required.
Description 1. Tough film and good adhesion on the concrete, able to penetrate into concrete. 2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties. 3. Good resistance to impact and abrasion. 4. Easy application , drying fast. Prepare to use 1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity. 2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application. 3. Two packs product, must be used completely during the duration of its pot life. 4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??. 5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion. 6. Keep away from heat, sparks and flame. 7. Stored with good ventilation. 8. Keep adequate ventilation during application. 9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying. **The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel. Color : Clear Drying time : Tack-free : 2 hours Hardness : 8 hours Full cure : 7 days (grease)
DESCRIPTION CC-604SP is two component water based epoxy primer, composed from water based of liquid epoxy resin and hardener. APPLICATION 1. To prime the surface and help the following application procedure to mold and decorative coating. 2. Highly resist to chemicals in non-circulated places. 3. With well adhesion ability with epoxy system or PU system application. 4. Suitable for hospital, operation room, food factory to prevent the mold, dust and bacterium. CHARATERISTIC 1. Able to be diluted by water. 2. Anti- efflorescence , suitable for the environment with highly hygienic request. 3. Good adhesion to the moisture surface, can take as the primer for solvent-free or solvent-based epoxy resin.
CS-613W is 2-component water-based premium epoxy product. CS-613W as admixtures can improve the properties, particularly in relation to water absorption reduction, toughness enhancement, vibration damping and increase of the bond strength of cement to reinforcements other than being used as admixtures, CS-613W is used partial replacement of fine aggregate, for coating, sealing and repairing concrete and for coating steel reinforcing bars for corrosion protection. AREA OF APPLICATIONS Repair mortar for concrete areas. Industrial flooring. Bonding agent for new to old concrete. As water based primer. Can be applied with damp surface. FEATURE Weatherproof and waterproof of capabilities that help prevent the deterioration of the ground-coat material. Low odor. Washable with water including tools. Best to wash as soon as possible before it hardens.100% water resistant when cured.
CA-010P as a water-based primer in relation to water absorption reduction and increase the bonding strength of cement to reinforcements other than being used as admixtures increase the mechanical properties and the adhesion of the hardened material. AREA OF APPLICATIONS Repair mortar for concrete areas Industrial flooring Bonding agent for new to old concrete Enhance adhesion strength of mortar
DESCRIPTION Bituminous Primer is product containing oxidized bitumen and a mix of technical quick drying solvents. APPLICATION Bituminous Primer is recommended to block the dust and the porosity of concrete surfaces allowing the quick application o f the bituminous polymer membranes, both with flame application and cold bonding with bituminous sealants or with self adhesive membranes.Bituminous Primer allows quick film drying, has an excellent penetration and adhesion to the support for the absence of surface stickiness. INSTRUCTIONS FOR USE Concrete surfaces must be dry, clean and free from oil, dust or release agents. This type of primer is ready for use after mixing it. Bituminous Primer can be either sprayed or applied by means of roller or brush. In case of hot application of membranes with flame, the primer can be used only if surfaces are completely dry. On the contrary, if the surface is damp, it is recommended to use a bituminous primer specific for damp surfaces. The drying time depends on concrete porosity, on the quantity of product applied and on the temperature of both the surface and the environment. Usually the film gets dry after 2-4 hours from the application. The drying time can increase in case of cold temperature and with low a bsorption surfaces. PACKING 5 gallon Bucket SHELF LIFE The product can be stocked in closed buckets and in dry area, far from UV rays for 12 months. TOOL CLEANING After use clean tools with common solvents.
DESCRIPTION CC-600SP is a two component, solvent-free epoxy system with high chemical resistance and high bond strength. The epoxy may be applied as a primer for most high end industrial coatings, like Epoxies, PU. CHARATERISTIC Easy apply Low odor High bond strength Abrasion resistant Chemical resistant APPLICATION Concrete coating Cement
Second Hand Marine Engines, Yanmar, Mitsubishi, Yamaha, Komatsu, Niigata, Hanshin, Akasaka, Cat, Mtu.
OEM No.: 6G5-45571-00-00, 6G5-45570-00-00 Fitment: Yamaha Outboard 175HP 175ETLG 1988 Lower - Drive 1 Yamaha Outboard 200HP 200ETLG-JD 1988 Lower - Drive 1 Yamaha Outboard 200HP 200ETLG 1988 Lower - Drive 1 Yamaha Outboard 200HP 200ETXG 1988 Lower - Drive 1 Yamaha Outboard 175HP 175ETXG 1988 Lower - Drive 1 Yamaha Outboard 150HP 150ETLG-JD 1988 Lower - Drive 1 Yamaha Outboard 150HP 150ETXG 1988 Lower - Drive 1 Yamaha Outboard 150HP 150ETLG 1988 Lower - Drive 1
Fireproof paints and coatings.
Multifunctional solvent - based color paste, colorant, coating, paints, other solvents, agent, and additive.
Min jung hong is a company established in 1998 specialized in lubricant, engine oil, and all kind of oil. We mainly deal with the production of industrial lubricant for cars, motorcycles, agricultural machinery and maintenance chemicals. Lubricants
Mercury outboard, mercruiser parts, alpha, bravo, sterndrives, inboard engines, optimax, verado, marine engine parts, propellers, sierra parts.
Boats & ships diesel spare parts, valve seat, valve cage, valve bush guide, flange, indicator cock, pump housing, injection pipe, tappet screw, valve rotator, water pipe ferrule, connection piece.
Mercruiser parts, marine part, mercruiser engine, boat engine parts, boat motor parts, exhaust, marine engine.
Marine equipments.
Hardener for Epoxy: Reactive Polyamide Resin Denaturalized Polyamine Denaturalized Polyamine Additive Solvent-diluted Polyamide Resin
Webbing, cargo control products, tie down, sling, tow strap.
Marine diesel engine spare parts.
Marine product, bilge pump, water pump, DC pump, wiper motor, arm & bllade, float switch, bilge blower.