DESCRIPTION Bituminous Primer is product containing oxidized bitumen and a mix of technical quick drying solvents. APPLICATION Bituminous Primer is recommended to block the dust and the porosity of concrete surfaces allowing the quick application o f the bituminous polymer membranes, both with flame application and cold bonding with bituminous sealants or with self adhesive membranes.Bituminous Primer allows quick film drying, has an excellent penetration and adhesion to the support for the absence of surface stickiness. INSTRUCTIONS FOR USE Concrete surfaces must be dry, clean and free from oil, dust or release agents. This type of primer is ready for use after mixing it. Bituminous Primer can be either sprayed or applied by means of roller or brush. In case of hot application of membranes with flame, the primer can be used only if surfaces are completely dry. On the contrary, if the surface is damp, it is recommended to use a bituminous primer specific for damp surfaces. The drying time depends on concrete porosity, on the quantity of product applied and on the temperature of both the surface and the environment. Usually the film gets dry after 2-4 hours from the application. The drying time can increase in case of cold temperature and with low a bsorption surfaces. PACKING 5 gallon Bucket SHELF LIFE The product can be stocked in closed buckets and in dry area, far from UV rays for 12 months. TOOL CLEANING After use clean tools with common solvents.
DESCRIPTION CP-311T elastic polyester is a new type product with a special polymerization. It is a one compound high-performance elastic waterproof membrane. The single-liquid self-crosslinking waterproof polymer with anti-fouling and wear-resisting properties is used for the coating and protection of elastic waterproof materials, roofing, wall and other elastic materials. This product has high adhesion, elasticity, wear resistance and protection. It is water-resistant, weather-resistant and hydrophobic. It is the best choice for long-term protection. SPECIFICATIONS 1. AppearanceWhite Emulsion 2. Solid Content48~52 % 3. Viscosity3000 ~ 6000 cps(RVT#3@25) 4. Proportion1.15~1.25 PROPERTIES Developed with an environmentally friendly formulation that is water-based, non-toxic and low-odor, in line with environmentally friendly low VOC regulations and CNS waterproofing specifications. The self-crosslinking single-liquid resin can make the construction work simple, and can be directly sprayed, rolled or brushed. Suitable for indoor, outdoor, floor and wall applications with high toughness, water resistance and wear resistance Excellent film properties: elastic value and stretchability, and excellent wear resistance Weathering, aging resistance, can effectively increase the life of the paint Excellent adhesion, breathability and foam resistance, which can effectively prevent surface blistering and false after application.
Features * With excellent adhesion, non-sagging and construction resistance. * Without cracking and bulging after curing. * Specific design for spray plastering. * Applying by spraying machines efficiently. * Suitable for tiling. * Interior wall, exterior wall, panel wall and small area ceiling rendering. Application 1. Substrate must be free from grease, mould oil, rust, rusty metal , wood peels, paints, plastics, loose particles, contamination on any traces of foreign materials affecting the adhesion of CS-010. 2. Moisten the substrate overnight and also at the time before the commencement of operation. 3. Suggest to use CC-400 Concrete Bond as primer to adding adhesion for smooth and low porous substrates. 4. CS-010 is suitable for any type of spraying machine. Mix a packet of 40KG powder with 6.4liter of water and stir well for use. Its thickness should be maintained at 15mm and wait for 6-24 hours to apply for increasing the thickness. Storage Storage life is 12 months if the product is kept in a dry place. Package 40kg/powder bag
DESCRIPTION Cement Filler is used for exterior coating on the tiles, steel plate, a smooth surface or a low porosity material to combine the old surface and the new one. FEATURE * Water-based formulations of two special adhesive. * For tiles, steel, a smooth surface or a low porosity of the material surface ?¯ etc. * With waterproofing, impervious, weather resistance, freeze-thaw characteristics. * Can be used both on wet and dry surfaces. * With good adhesion. APPLICATION * To adhere and mix old concrete surface and new concrete surface * Can be used to adhere indoor and outdoor old cement walls, fiber cement board, tile, concrete, colored steel board, asbestos and various green compartment plates etc. WORKING PROCEDURE 1 All surfaces need to be clean, free from dust, rust, white birch and either grease. In addition, the concrete could be moistened but not with floating. 2. Coating CA-003M by brush, roller or spray on the substrates. The coverage would be 4 ~ 7m ² per kilograms which depends on the situation of porous and roughness of the substrates. 3 All the tools can be cleaned by water.
Feature: 1. 400lb safe working load 2. Folding seats 3. Dual knee pads for secure transports 4. Hooks for optional side support strap 5. Fits through narrow door ways 6. Optional seat lock ST400 Standing Transfer Aid ST400 is your entry level aid for standing transfers. Transfers are quick and require minimal assistance. Swivel seats support the patient and allows for a quick and comfortable change from sitting to standing and vice versa. Additional attachment hooks for a support strap are also included. Swing seats and grab bar allows patient to pull themselves on board with their own strength. Fixed tapered base allows the unit to squeeze in between tight spaces. Specification: ASeat width50.8cm BFixed base inner width41.2cm CFixed base outer back width63.2cm DOverall length79cm EMin. seat height67cm Eâ??Overall height109cm Unit Net Weight30kgs Lockable CasterYes
Dual functions Fast drying 2 in 1 -adhesive sealant Faster and higher green strength than solvent based construction high strength formed after 5 hrs. Water-based construction adhesive is developed to serve as adhesive and sealant give good wet grab. The adhesive is tough but also flexible. Developed for both professional and home handy man using AFTEK own new technology. 1. Fast setting 2. Very Tough but flexible with good degree elasticity 3. High heat resistance better than solvent based adhesive 4. Plasticizer resistant 5. No Sagging No sliding on smooth surface, can use on ceiling 6. No Drooling, no wastage and no mess on floor to clean up 7. High wet grab good for sticking heavy tiles and not slippery. 8. Easy to extrude even on cold day. Features: * Almost odorless. * NO VOC safe to use indoor. * Exceptional fast bond development. * Creamy smooth easy to spread. * Highly thixotropic easy to use on wall and ceiling without dropping off. * Good gap filling properties-suitable for filling uneven surface or small crack due to high solid content. * Paintable when dry. Product Specification: Highest Solid by weightâ?? 82% -83% few if any can match it. * SG â?? 1.65 â?? low filler surface area more binder for better adhesion. * pH 6 â??7 â??Near neutral safe on substrates. * No caustic soda or ammonia safe to use at home. * 5 hours bond strength 2.0 kg force/cm2 * After 24 hrs Bond strength 22 kg force/ cm2 no other WB adhesives can match that. Clean Up Clean up tool as soon as possible with water before it set hard. For harden adhesive, scrap off as much as possible with a strong scraper. Use solvent such as mineral turp to soften the remaining adhesive. Shelf life â?? I year if kept at ambient temperature within 5â?°C - 35â?°C.
DESCRIPTION CP-502 is Ethylene-Vinyl Acetate copolymer latex , it has film with flexibility. It can be use to mix cement , extend prolife and reduce stiffness of cement. APPLICATION CP-502can be use to mix cement , extend prolife and reduce stiffness of cement, and it has flexibility and waterproofing after cement solidification. It is a elastomeric coating used to the surface of a cement wall, the latex can add to more filler and change the viscosity unapparent. THICKNESSï¼?About 1 mm when just sizing; about 0.8 mm after dry COVERAGEï¼?About 2 Kg/m2 ï¼?Dry membrane reach to 2 mmï¼?apply 2~3 timesï¼? SUGGESTIONï¼? 1. Tools: Brush/ Roller/ Spray Gun 2. Normal: EmulsionAAggregateB11By Weight 3. Enhance elongation performance by increasing emulsion content 5~10%. 4. To get better tensile strength might reduce the usage of emulsion. 5. Dilute with water if apply by roller or spray gun. Add 10 6. Avoid cracking, shrinking or other paint failure by following PRIMERï¼?CA-002 or CA-003 dilute 2~3 times for using COATINGï¼?Water-base Paint. Test before using, if apply solvent-base paint. DILUTE AGENTï¼?Waterï¼?5ï½?10% for rollerï¼? PRECAUTION CP-502 should be stored below 40â??,and be kept away from sunlight or fire. Shelf life is one year.
DESCRIPTION STARCOAT PL, is fine grade cement based finish plastering skimcoat which contains selected filler and additive used for smooth finishing to uneven wall cement based plaster and ceiling. After dry STARCOAT PL have a good adhesion to the substrate, no cracks, smooth, no dust on the surface and ready to be painted with water based paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS *Cement Based Wall Plaster. *Precast Concrete. *Concrete Profile & Concrete Ceilings *Internal & External. ADVANTAGE *Light, good workability and sanding properties. *No cracks and hair cracks. (depends on background) *Smooth surface, solid and no powdery. *Can be painted or finished with wallpaper directly after dry in minimum 24 hours without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler: Limestone 3. Color: GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage: 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness: 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life: approx. 60 minutes SURFACE PREPARATION 1. The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. 2. Porous and absorbent substrates must be pre-wetted prior to application of Starcoat PL finish coat.
1. sensor products, includes hydrogen sensor and pressure sensors 2. voltage regulator of alternator 3. module of voltage regulator 4. ic.
Product: stainless steel in coil / sheet / plate / strip grade: 201 / 202 / 301 / 304 / 304l / 409 / 430 / 410/ 316l / 321 finish: no.1 / 2b / ba / no.4 / hl / sb / no.8 / decoration / color.
90-32-2, 90-48-2, 90-17-4........etc Various spec and custom-made available
Specification : 1. Ash content around 3% 2. Moisture content around 8% 3. Fat content is around 16.71% 4. Crude fiber content is around 10.55% 5. Protein content is around 15.42%
- chromed steel frame - transparent tempered glass top sp.4 mm - Ø43 cm - height adjustable 5 positions - dimensions cm. H.69/74/79/84/89 x Ø48 - top height cm. H.58/63/68/73/78
The listed price USD 225 based on MOQ: 20 pcs. Never try Scams, we are always vigilant on online scams. If you are really serious buyers (neither suppliers nor scammers), welcome to reach out to me directly by Google with keyword: (soartec.mybranchbob) for more product details. To attention of serious buyers of air powered pneumatic tools sanders, you might look for the products within your interest first, then just make business friends with the suppliers who have the products you want; but I suggest you may try making business friends with me Roger first, then just see if I have the products you want. *Product Features: *Blade featuring a spring-mounted mechanism to prevent deadlock or power-related issues. *Incorporation of a 2-step throttle system aimed at enhancing operational convenience. *Product Spec.: *Model: WS-2106 *Hammer Mechanism: Twin Hammer *Std. Bolt Cap.: 30 (mm) *Max. Torque @ 5s: 1630 (ft-lb) *Length: 434 (mm) *Trigger: 2 step throttle type *Regulator: 4 position power *Anvil length: 6' Price: 225.00 USD based on MOQ: 20 pcs.
Large-sized indium tin oxide (ITO) coated glass plays a pivotal role in energy-efficient building materials and solar energy. It applies to solar-related products and finds utility in electrochromic dimming windows and liquid crystal windows. More info. on GemTech's website: https://www.gem-tech.com.tw/En In the domain of energy-efficient building materials, large-sized ITO coated glass holds immense potential for window applications. Electrochromic windows and liquid crystal windows, by adjusting the voltage, modify the transparency of windows, thereby achieving light control, privacy protection, and creating a comfortable indoor environment. In the domain of solar energy materials, ITO coated glass boasts excellent conductivity and transparency, making it an ideal choice for solar cells and transparent solar windows. As technology continues to evolve, large-sized ITO coated glass becomes an integral component of sustainable development, bringing forth new possibilities for the construction industry, and further propelling the advancement of sustainable development and intelligent building. Substrate thickness ( mm ) 2~4 Substrate size ( mm ) 1700x3000~2134x3658 Substrate type Architectural glass We also provide coating service on client-supplied materials.
NAN item no:CO003 Car Brand : TOYOTA LITE/TOWNACE TRUCK KM2#,TM20,YM2#,CM2#(1979-1986) TOWN/MASTERACE V,WG KR1#,RR1#,2#,TR1#(1976-1982) HILUX RN3#,4#,LN3#,4#(1978-1988) YN5#,6#,LN5#,6#(1983-1989)
Despite body mists and perfumes are both classified as fragrances, they are not the same. The biggest difference between the two, according to perfumer Mandy Aftel, is their smell intensities. The body mist spray wholesale is a light fragrance mist that is designed to be sprayed on the body. It has a milder aroma than typical perfumes and is designed to be used in a layering effect with other items such as lotions, shower gels, and body creams. Dive in and explore what body mists we have to offer! WHAT ARE FRAGRANCE BODY MIST USED FOR? Body mists moisturize your skin and leave you smelling fantastic and feeling refreshed for the day ahead. Because they only last a few hours, you'll need to re-spray your body mist throughout the day if you want to utilize it for scent layering. As a general guideline, reapplication every 2 to 3 hours is sufficient to keep your smell fresh and evenly applied throughout the day. 5 GOOD REASONS TO USE A BODY MIST 1. BODY MISTS WORK WELL FOR LAYERING Layering is essential if you want to maximize the aroma you're wearing for the day. Utilizing a body mist in conjunction with a body lotion or scented shower gel will result in a longer-lasting aroma that you won't have to reapply. 2. THE SCENT OF BODY MISTS IS LIGHT AND SOFT. A body spray is an excellent alternative to wearing a strong, overpowering perfume. In a circumstance such as an interview, they produce more subtle initial impressions. They're also perfect for topping up in public places when you don't want to intrude on other people's personal bubbles with a powerful spray! 3. BODY MISTS HAVE MORE THAN ONE APPLICATION Body mists may also be used to freshen up other aspects of your life! If you have an outfit that has been sitting in your closet for too long, hang it up and spritz it with your mist (keep the spray at arm's length to minimize any harm to your apparel). Perhaps you have guests coming to your house and want to set the tone. Mist the space or cushions/throws gently to create a nice touch. 4. A BODY MIST IS GOOD FOR YOUR BANK BALANCE Several of our favorite designer companies now sell their distinctive perfume smells as a body mist. They are also less expensive than their EDP counterparts due to less oils/concentration factor. Thus, if you adore a cult designer smell but are on a tight budget, utilizing a body spray wholesale is a terrific method to achieve the fragrance you desire for less, such as these beauties. 5. BODY MISTS CAN SUPPLEMENT HYDRATION Besides from smelling fantastic, a body spray may also give moisture to your skin. If you're seeking for a moisturizing body spray scent that also smells amazing, check out CHANEL's Moisture Mist line.