The line is designed to fill beer in to three different type of 0,33 litre glass bottles, label the bottles neck around and lower body small around and pack the bottles in to 4 x 6 bottle cartoon boxes. This bottling line capacity is 20000 bph. Clean glass bottles were brought on wooden pallets to depalletizer which feed them to the filling lines. Innofill DMG bottle filling machine and Handtmann MMS filtration system are located in a clean air room. KHS lamella conveyor system for bottle transport and cartoon boxes. The equipment were totally delivered by German KHS in year 2003, most of machines manufactured in year 2002. All control units are Siemens Simatic S7 model with remote connection. The line was shut down in year 2008 and it is still installed and in very good operational condition. Main equipment are: - Bottle Depalletizer KHS AL, semiautomatic - Micro Filtration Handtmann MMS 130 - Filling Equipment KHS Innofill DMG (rinsing, filling and capping) - Labelling Machine KHS Innoket 2060 - Cartoon Box Forming Machine KHS Innopak CA-1 - Bottle Packing Robot KHS Innopak SP 1200 - Box Marking System - Case Sealer KHS Innopak CV.
Good condition filtration press made ny German MSE Filterpress GmbH in year 1997. The press has 33 plates of size 630 x 630 mm, cace thickness 25 mm. Includes own hydraulic system and control cabinet. The equipment is manufactured by German MSE Filterpress GmbH, year 1997. Manufacturer’s type KFP 630-40-25K-MPN+DLMP. Structure is made on normal construction steel, plate size is 630 x 630 mm. The filter plates are pressed with single acting hydraulic cylinder with inbuilt hydraulic pump-motor. Product is fed in a central sludge feed inlet with flange connection and each pressing unit has its own outlet for the liquid filtrate which is them collected in one outlet channel. The cake will be disposed under the press. The unit has its own control panel attached to the equipment. Technical data: Manufacturer: MSE Filtterpress GmbH Year of manufacture: 1997 Manufacturers type: KFP 630-40-25K-MPN+DLMP Plate size: 630 x 630 mm Number of plates: 33 Cake thickness: 25 mm Hydraulic pressure: 380 bar max Filtration pressure: 15 bar.
Kisters Wrap Around Packer 310 Kisters fully automated wrap around packer model 310 is a single-lane, high-performance packing robot for producing wrap-around and tray packs from stable individual products. It can handle tins, cans, jars, glass and PET bottles, as well as pre-packed products from the beverage, hygiene and food processing industry with high packaging speeds. It can process flat corrugated cardboard and full carton blanks in different qualities. In each case, the carton is folded tightly around the product groups and subsequently glued with hotmelt and it has a large and easily accessible cardboard blank magazine. Optimum packaging results are achieved in conjunction with the precise cardboard blank guides and the exact folding process. Wrapping robot can handle a wide range of formats. The unit is PLC-controlled and it can be easily adjusted for other packing formats. This machine has been packing beer tins (12/24 x 0.3 liters and 12 / 24 x 0.5 liters) into cartoon wrap-around packs at speed of 60 packs / min. This unit was in full operation till beginning of November 2010 and is now dismantled and stored. Technical Data Manufacturer: Kisters Machinenbau GmbH (Nowadays KHS ) Model: Wrap Around Packer 310 / 100 Year of manufacture: 1994 Serial number: 941782 Capacity: upto 60 cycle / min Electricity: 16 kVA, 400 V / 50 Hz
This laminating tunnel / convection oven is made by Swedish TRIAB / Tri Innovations AB in year 2006. The oven is designed for industrial use and in build up in two separable laminating sections, both equipped with one 40.5 kW hot air sections, one product and one return conveyors and common control unit. All product touching parts are made either of stainless steel (structures and panels) or Teflon made net belts. Convection belt (600 mm wide) is located inside of the oven tunnel and has grid type surface, the return conveyor is installed on the tunnel and it has tight waived Teflon belt. The control cabinet is attached to the equipment structures. The speed of laminating conveyor is adjusted with an inverter driven motor. The speed of return conveyor can be fine tuned via a potentiometer. The equipment is featured with a remote control possibility. This has been operating with hygienic products (material foam / polyurethane film, thickness 5 mm, max. width 450 mm and production speed 6 m/min) and is in excellent operational condition with total 3450 operating hours only and it comes with original operation manual in English language. Technical data: Made by: TRIAD / Air Innovations AB Manufacturing year: 2006 Total operating hours: 3450 Convection capacity: 2 x 40.5 kW Process control PLC: Eurotherm 2216e Hot air circulation volume: 2 x 9000 m3/h Fan electric power: 2 x 2.2 kW Temperature range: 50 – 150 C Total machine length: 10 000 mm Total machine width: 1600 mm Convection belt material: Teflon covered metal net Convection belt length: 9 000 x 600 mm Convection belt speed: 3 – 8 m/s / 0.25 kW, inverted controlled Heated width: 650 mm Inside / free height: 80 mm (from belt to nozzles) Return conveyor: Habasit FAB-8EO WV Return conveyor dimensions: 12000 x 600 mm (Teflon) Return conveyor drive: 0.25 kW, 380 V/50 Hz.
The vacuum evaporator is made by Italian Ecoteck in year 2003 and operation was stopped in early 2009 and it is in very good operational condition. This unit is made for concentrate acidic liquid wastes and therefore all liquid touching parts are made of acid proof steel ( SS 2353) or PVC. The evaporation capacity of the unit is 5000 liters / day. The unit is a complete working unit and it includes evaporator, boiler, heat pump, centrifugal pump, water-air cooler, steam ejector, control unit and all other necessary equipment to complete the unit. Operation principle: Steam rises from the boiler through a drop dispenser to the cooling unit where it condensates. The condensate drops with the gravity down to vacuum system. In-build heat pump heats up the cooling media and simultaneously cools down the condensate. Water – air cooler cools down the extra heat from the process. Necessary vacuum is generated with a centrifugal pump and a steam ejector. Condensate rejection takes place in accordance with prescheduled frequency. Technical data: Manufacturer: ECOTECH Srl Italy / Vilokan Ren Miljöteknik Sweden Type: ECO 5000 VS-HP, R407C Year made: 2003 Evaporation capacity: 5000 liters / 24 hour (pure water) Electricity consump.: about 0,15 kWh / liter pure wateri) Control unit: Siemens Micromaster 420 Compressor: Bitzer Kuhlmachinenbau GmbH, Compressor type: 6G-40,2 Compressor capacity: 126.8 m3/h, 19/28 bar Refrigenerant: R 407 C Main dimensions: 2.8 m x 1.3 m x 2.9 m Weight: 1500 kg.
ating line is delivered by Finnish Elmont Oy and it consist of 59 separate dipping tanks, 6 material handling cranes and related process and automation equipment. We have the dipping tanks and material handling cranes in our store for sale. Dipping tank materials are AISI 316, SS, PP, HST and PP. All tanks are 2200 mm long and 1250 mm height, widths varies from 450 to 1740 mm, volumes from 1213 to 4016 liters. All tanks are in good condition. The cranes are designed for those tanks and we have 6 pcs of them. Cranes have 0.25 kW gear motors and control panels. Structure is made of steel and they are in good condition. If you are looking for such equipment, please contact us and we are pleased to give you more deep information.
The recovery plant is specially designed to recover CO2 from fermentation processes at breweries. This complete CO2 plant was installed in 2001 and it has nominal CO2 removal capacity of 1000 kg/h. The plant has Siemens S 7 control system where operation is carried our via a large 12 " color screen panel with Windows CE operating system. This is a complete CO2 recovery plant and final delivery scope depends on buyers needs. The plant has been in operation only approx 5 years and is still installed and in very good condition. The carbon dioxide plants was designed by Danish Union Engineering (www.union.dk ) and the delivery includes following main components: - 1 Scrubber for gas flushing - 2 Foam catcher vessels - CO2 collection, inflammable - 2 Mehrer TZW 70 CO2 compressors - 2 Carbon filters - 2 Dehydrators - CO2 Liquefier - CO2 Storage Tank - 2 Cooling compressors GEA Grasso GD-3 for R717 - Air cooled condenser for NH2 compressors - Alarm center for CO2 and NH3 concentration - Station for 40 kg CO2 still tank filling - CO2 pumping station from a truck to the factory - CO2 purification tester - Steam heated evaporator for liquid CO2 Detailed technical information available for serious buyers
Manufacturer pompetravaini italy, made in year 2002. Vacuum pump is two staged rotating pump with externally located, grease lubricated bearings. Pump is liquid ring type designed for water sealed operation. The impeller and shaft are made of stainless steel (aisi 316), cast iron casing and manifold normal steel. The shaft is sealed with double mechanical seal. Pump is provided with connections for service water and draining. Pump includes also anticavitation valve. Pump is dismantled from its base frame but the delivery includes original electric motor eex classified abb hyr 200m lb 4 30 kw, 1476 rpm, year 1995. The equipment will be supplied loose - not as a skid. Technical data:trch 80 - 540/c2/ra Max suction pressure:25 mbar (till 300mbar) Max capacity:540 m3/h (min 400 m3/h) Flanges:80 mm Rotation speed:1500 rpm Power requirement:30 kw at 1500 rpm Year made:2002 Condition:fully operational
Rotary Lube Blower / Vacuum compressor KAESER EB 420 C û 38 m3/min, 53 kPa There are two identical sets of oil-free, 2 lobe rotary blowers, made by Germand Kaeser Kompressoren GmbH in year 2005 with accessories. Manufactures type is Kaeser ED 420 Compact Omega Pluss 53 and accessories include a control cabinet with two inverters and programmable Kaeser Start Control STC 30 unit, totally 6 preliminary intake air filters and 3 final air intake filters with their steel supports. The rotary blower units have removable sound enclose for noise insulation. Operation of the equipment was stopped in year 2007, total running hours approx 7000 and therefore they are in excellent operational condition. In addition, we can offer you service maintenance by the manufacturer at separate cost. This equipment is suitable for demanding dust collection and pneumatic transportation of various products due to oil free operation. For pneumatic transport application some changes in filters and other parts are needed. The rotary lobe has two blower shafts with high efficiency Omega profile in a blower block. The rotary lobe and the block have a very small distance and they are not touching each other's and therefore there is no need for lubrication oil. The rotors are driven by high efficiency electric motor via belt connection and they both are installed on the same base frame. . The inlet and discharge silencers are designed to be effective at all frequencies and are eminently suited to variable speed . Higher rotational blower speeds produce high volumetric efficiencies, which in turn lower discharge temperatures and power consumption. The Compact Range ensures that all serviceable items are accessed from the front panels of enclosures. The preliminary intake air filters are combination of cyclone and bag filter and it removes most of the dust from inlet air. Fine filter is a combination of cyclone and 138 ceramic fine filters which removes fine dust very effectively. Technical Data Manufacture's type: EB 420 Compact Omega plus 53 Manufactured in year: 2005 Suction capacity with max vacuum:38,0 m3/min Power demand max: 40,3 kW Rotor's rotation speed 4120 rpm Max suction vacuum: 0,53 bar (abs.) Discharge pressure: 1,0 bar (abs.) Max pressure increase: 470 mbar Temperature rise max -t: 82 K Electric motor: 45 kW û 50 Hz / 400/690V û 83/48 A Electric motor nominal speed:2965 rpm Protection class: IP 55 Inverters: Mitsubishi FR-F740-01160-EC Case ventilation fan: 370 W û 50 Hz / 230 / 400V Weight blower with the case:1120 kg Blower case main dimensions:1.8 x 1.7 x 1.8 m (K x L x S) Noise level: 99 dB (A) Noise level with the case: 84 dB (A).
Industrial Crane Konecranes CTX 10 t, Dual Bridge with 33.6 m span The crane was manufactured by Konecranes Oyj in 2001 and the operation was stopped in year 2006. The equipment was regularly serviced by the manufacturer and is thus in excellent operating condition. The crane is still installed in its original place and can be tested on any time. The double bridge is welded housing construction equipped with one double speed wire hoists and a motorized rail equipment on both ends. The crane has both the local wire connected control unit as well as the wireless remote controller. On the bridge there is a service platform and the local LV û and control cabinet. All electric motors are dimensioned in accordance with Industrial Heavy Duty ED classification. The equipment includes the crane moving rail which will be sold separately. Technical data: Manufacturer's type:CXTD10t x 33.6m Hol: 6.1m Lifting capacity:10 000 kg Span distance:33.55 m Lifting class:FEM M5 (2m) Bridge structure:Welded case Total weight:Approx 22 000 kg Type of wire hoist:XL 404N40BDA4 Lifting height:6.1 m Lifting speeds:8.0 and 1.3 m / min Wire hoist speeds:32 and 8 m / min Bridge speed:Inverter controlled, max 40 m / min Wire hoist lifting motor:Double power 15 and 2.5 kW (60% ED) Wire hoist moving motors:2 x 0.65 kW (40% ED) Bridge moving motors:2 x 1.8 kW (40% ED) Total power need:19.9 kW / 400 V / 50 Hz Crane moving rail:60 x 40 cm, length 2 x 140 m.
Compressor single stage, standard speed oil-injected rotary screw compressor with manufactured by German company Drucklufttechnik GmbH in year 2002. The complete unit consists of intermediate pressure vessel and Ultratroc - air dryer all delivered same time as the compressor. The unit is controlled by modern DELCOS 3000 control unit. The total unit has 30320 operating hours, the unit has been regularly serviced by a compressor service company and is in good operational condition. The compressor is single-stage, double screw, V-belt driven electric motor drive compressor which has oil cooler and thermostat controlled water - air after cooler on discharge of the pressurized air. The operations were stopped in year 2006 but the compressor and other equipment are still installed and ready for test run. Technical data: Compressor type:CompAir L90 7,5A Capacity:16.1 m3/min, 7.5 bar Comp. electric motor:90 kW - 400/415 V û 50 Hz Air cooler electric motor:3.0 kW - 400/415 V û 50 Hz Compressor weight:2380 kg Compressor dimensions:2.4 x 1.4 x 2.0 m (W x L x H) Air dryer type:Ultratroc SD 1350 û type 422 Air dryer air volume:22.5 m3/min Total power requirement of dryer:2.4 kW DryerÆs refrigerant:Type R134 a û filling 3.5 kg DryerÆs dimensions:1200x900x800 mm, weight 185 kg Int. mediate air pressure vessel:Volume 2 m3, 10 bar, made by Galvanoimis Oy.
The main description of the plant equipmet is: 1. Brew House Make & Capacity: Steinecker1995 -1999 5 brews/d, 450-500 hl/brew. for 7000 kg malt, 3850 Raw grain Cast-out quantity: 500 hl, 16,5° Plato 8 Brews/ 24 hours, annual capacity 0.85 Mhl Controls are based on Siemens S5 and S7 PCS with, Botec Control system, PC Windows 2000 (Steinecker) Laboratory yield = 97.1% (2.1.09 – 28.5.09, 837 brews) The Brewhouse was installed in 1996 - 1999 by Steinecker to a high standard of control and automation and it contains the following main equipment: Wet Conditioning Mill, capacity 20 tons/hour and it is fully overhauled 2008 Configuration, main characteristics: 1 wet mill plant: 20 t/h 1 mash tun kettle plant: V=550 hl 1 lauter tun plant: D=7200mm 1 weak wort tank: V=155 hl 1 pre run vessel: V=640 hl 1 CIP- water distributor brew/whirpool kettle hot wort max. 520 hl (1 brew / 5 hours) wort cooling 400 hl/h, 10°C - Mash Kettle, a jacketed vessel 550 hl - Enzyme Dosing pot and pump - Lauter Tun complete with spent grain tank and Pondorff pneumatic grains transfer. Tun capacity 814 Hl and diameter 7200 mm, Solids capacity of 7000 kg malt and 3850 kg raw grain. Complete with internal rakes and scrapers - Pre Run Vessel complete with internal heater , volume 640 hl - Wort Boiler/ Whirlpool, gross volume 757 hl net 520 hl - Wort Cooler with aeration – GEA supplied plate heat exchanger (YOM 1990) – rated at 450 Hl/hr cooling the wort from 95oC down to less than 10oC. Cooling achieved with brewing water and then chilled water. Aeration achieved by use of a sintered disc and static mixers, and controlled manually using mass flow meters - 2 Hop Pellet Tanks - 2 Hop Oil Tanks - Brewhouse Weak Wort Tank, volume 150 hl - Alfa-Laval Decanter, year 2008, capacity 100 hl / h - 2 Weak Wort Tanks, volume approx 80 hl each - Gypsum Tank, volume approx 40 hl - Wet starch tank – volume 100 hl - Spent Grains Silo - Spent Grains Drying System - Bulk Acid tank – plastic tank with integral bund and dosing pumps
This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit. This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate. Machine type:Powerpak 660 Machine number:665/0211 Manufacturing year:1998 Foil type:Flexible Formatting width:430 mm Film type used:PS-PE 450/50 Max formatting depth:40 mm Forming dies:223-3,1 Capacity:10 phases / min Control unit:Tiromat Ho foil printer:SC-700 with 3 printing units Overall length:7.30 meters Overall width:1.15 meters Height:1.85 meters Nominal power need:50 A / 380 V / 50 Hz.
Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets. More information on requests, for spam protection please introduce yourself properly. Main data of one mill: Manufacture’s type: NTK 130F/LM Year of manufacture 1988 Total operating hours: approx. 75000 Rated capacity, max: 145 kW Number of blades: 3 pcs Rotor diameter: 22 m Rotor speed: 44.5 rpm Cut-in wind speed: 4.0 m/sec Cut-out wind speed: 53 m/sec (120 mph) Hub height: 26 m Generator: ASEA 145 kW / 1500 rpm / 50 Hz Blade type: LM 9.7 m H/H/T diam. 21 m Gear box type: Lohman & Stolterfort GPC 145 Clutch type: Lohr & Brokamp Universal Joint No 105 Total weight: 15200 kg.
Good condition GEA Westfalia centrifugal separator used for molasses removal from fermented beer. The equipment has patented HydroStop solid discharged system that can be adjusted precisely and reproducibly to the specific solids concentration requirements of the process. This beer separator has continuous and self cleaning separation process and in beer filtration application this separator eliminates the need to use kieselghur. Technical information: Manufacturer: - GEA Westfalia Germany Year of manufacturing: - 2002 Manufacturer's type: - SC 30-06-177 Capacity: - 4000 - 6000 liters / hour Electric drive: - 18.5 kW Bowl diameter: - 440 mm Bowl speed: - 7270 rpm Relative density of solids removed: min 1.4 kg/l Relative density of suspension: max 1.2 kg/l Particle size or removed solids: > 4.6 micron Centrifugable solids: - max 5% v/v Viscosity of free liquid: - 2.5 - 5.5
e equipment was manufactured by Jeffrey Rader AB, Sweden in 1995 and it is in very good operational condition. It consist of two heavy duty rolls with removable profilied surfaces which rotate towards each other and presses overzised wood chips between the profiles. Roll drives 2 x 110 kW / 1500 rpm connected with two gearboxes. Hydraulic pump 7.5 kW, capacity 220 m3/h wood chips. The equipment was manufactured by Jeffrey Rader Inc, Sweden in year 1995, manufacturers type is DynaYield 80-300 and it is in good operational condition. The Chip Conditioner consists of two heavy duty rolls with removable profiled surfaces. They rotate towards each other and pull the oversize chips between them. The profiled surfaces are aligned so that the pyramid apexes on one roll travel in the valleys of the apexes on the adjacent roll. With normal oversize wood, the Conditioner typically generates less than 1% fines and 3% pins The normal application for the Chip Conditioner is in a chemical pulping process, processing the oversize materials by fissuring the wood chips parallel with the grain to allow the cooking liquors to penetrate the chip, and allow the oversize chip to cook as an acceptable size chip. Another application is in a thermo-mechanical pulping process (TMP), as a preconditioning An important feature of this machine is its ability to handle small portions of tramp without going off-line. With the so called Dynagage Conditioner, the dynamic roll is allowed to move away from the static roll, and once the tramp is through the unit, the roll automatically moves back to the proper set point without shutting down the flow and together with slow rotation speed enable were low down time and maintenance costs. Roll distance movements are made with a hydraulic system build on the equipment and controlled by 3 position sensors More information on requests, for spam protection please introduce yourself properly. Technical data: Model: RDY 80-300 Manufacturing year: 1995 Capacity (throughput): 220 m3/h loose wood chips Press roll diameter: 915 mm Roll length: 2440 mm Roll motors: 2 x 110 kW / 1500 rpm / 690 V – 50Hz Press distance between the rolls: 2.2 mm Gearboxes: 2 x Kipo Benzler TV 512 Hydraulic pump: Rexroth 200 bar with Mecman syliders Electric motor for hydraulic pump: ASEA 7.5 kW Weight: 33 000 kg Length: 5083 mm Width: 2550 mm Height: 2400 mm.
Krones Toptronic K 719-555 Rotary Empty Bottle Inspector The Toptronic inspector is made for inspecting empty returnable PET bottles and empty non-returnable and returnable glass bottles. It utilizes state-of-the-art camera technology to provide precision empty container inspection. The sophisticated inspection modules detect even the tiniest damage or contamination – both in glass and PET returnable bottles. General design features Modular design Table top cover and stand cladding in stainless steel Safe bottle guidance with Raptec handling parts Blower for removing foam and lubricant residues from the container base Enclosed and air-conditioned electronics cabinet Electronic function monitoring Stop function upstream of machine infeed in response to fallen-over containers Rejection unit with retaining bar or clamping starwheel This unit has been in operation only with PET bottles sizes 0.5 liter (four different types), 1.5 liter ( two different types) 1.0 and 1.25 liter bottles and it has been in operation since 2002 and is still in very good operational condition. Handling tools for above mentioned PET bottles will be a part of delivery. Technical specification: Manufactured by: Krones AG, Germany Manufactured in: 2002 Model: K 719-555 Nominal output: up to 72000 bph Actual output: 35000 bph (with clamping starwheel) Inspection units (PET) For foreign containers P.E sensor and camera Base 1 Camera Variostation 1 Camera - sealing surface Residual liquid High frequency + infrared Side wall Camera Optimized scuffing Camera Variostation 2 Camera - Base 2 - inner side wall - full thread Variostation 3 Camera - full thread - lateral neck finish - inner side wall Variostation 4 Camera - sealing surface - lateral neck finish Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Wood Working.
Yogurt production and packaging line 4000 l / shift 0732010 Yogurt production and packaging line 4000 l / shift Yogurt production equipment consists of 4 pcs 1000 liters of yogurt fermentation tanks, transmission equipment and a fully automated filling line 150 - 200 grams plastic cups. Process operation requires two people and equipment can be made about 4000 liters (or 20000 pieses) of 200g canned yogurt cups or other similar product for a normal 8-hour working shift. Packaging equipment is manufactured in the 1980s by German Ganzhorn & Stirm (nowadays Casti) and an automatic product cup feeder has been added later on the line. Also the tray feeding device has been recently added. The production line is fully operational and suitable besides for yogurt production, also for all curdled / fermented milk packaging in 150g-200g cups. Fermentation tanks are double walled 1000 liter stainless steel vertical tanks. The product temperature can be adjusted as desired (e.g.36C) by using heating water between double walls. Control valves are manually adjusted. The fermented yogurt is transferred to two 100 liter feeding tanks of the packing line with gentle rotary lobe pumps. Filling the yogurt cups is fully automated 2-lane packing process. The main equipment are manufactures by German Canzhorn & Srimin. Later installed automatic cup feeding equipment places 150 gr - 200 gr cups in 2 rows on the filling machine. The filling machine fills cups in three phases; first to the bottom desired volume of jam and then two different layers of product mass. ( 3-layer of yogurt). The cups are closed with aluminum lids which is sealed with electric heater. Transfer conveyor moves closed cups on to a palletizing machine which loads 20 cups on each cardboard or plastic tray (tray is automatically fed by a tray feeding device) where full trays are moved to a stacker machine which piles several layers of trays (up to 1 meter tall) for transportation. Technical Specifications: The manufacturer: Ganzhorn & Stirm (Casti) Filling machine type: DOGatherm 61 Stacker type: BE 75/2 Production capacity: up to 4000 liters / shift Yogurt fermentation tanks: 4 x 1000 liters Cups & filling: 150 - 200 g / max. 3-layer filling Filling line length: about 12 meters.
Stainless Steel Tank 3.5 m3, with variator driven mixer 3pcs excellent condition vertical stainless steel (food quality) tanks with electric motor driven and mechanical variotor speed controlled heavy duty two plade mixer. The tanks are made by Finnish Tankki Oy in 1992, they have are standing on 3 heavy legs, liguid volume 3.5 m3, conical bottom for easy discharge. Necessary service man door and other connections for venting, filling and discharging. Total height: 3.4 m (+ motor and connections 50 cm) Diameter of the tank: 1.6 m Wall height: 1.8 Mixer: Sew-Eurodrive KAF76-D34 Mixer rpm: 12.2 - 60 rpm Moment: 900 - 400 Nm Electric motor 3.0 kW / 1400 rpm.
Drum and Container Filling Line, Semiautomatic YOC 2006 The line is designed for filling both 1000 liter IBC’s and normal 209 liter drums / barrels. It consist of straight chain driven heavy duty roller conveyor which is carrying IBC’s or a standard pallet loaded with four drums / barrels through the filling process and conveying them for further storing. The filling machine is semiautomatic coarse-and-fine filling station; first is programmable volumetric and then fine filling with integrated weighing system. Cap closing / bunging and sealing will be made manually but a machine aided. The station operation is controlled by Siemens S7C programmable logic. The line is manufactured in 2006 by Finnish company “Insinööritoimisto Jyrki Kekälainen” who is specialized supplying automation solutions filling and packing applications. Operation description: The operator lifts the empty containers on the conveyor (open the cap of container), the container will move into filling machine and it will be filled automatically with 2 "and 1 / 2" valves, coarse-and fine-filling. After filling the container will move out of the machine and the operator will fix the label and close the cap. After the filling station there is ~16 m long puffer conveyor for the filled IBC`s, where a fork lift will pick up the IBC`s In drum filling the operator lifts the empty drums on pallet (open the caps). Then he lifts the pallet on the conveyor. In the machine there is an extra filling lence for the drums. The drums are filled on the weighing system of the machine which is controlling the filling of each barrel. After the drum is filled the operator move the lence into second drum and machine start to fill it. After all drums are filled the pallet will move out of machine and the operator will close the caps and fix the seals and labels. Technical data: Manufactured in: 2006 Suitable for: Standard IBC and Drums Max filling weigh: 1500 kg Filling accuracy: 0.5 kg Filling capacity: 7 IBC/hour or 35 Drums (209 liters) / hour Roller conveyor type: Chain Driven, Galvanized Roller conveyor length: Approx 16 meters Roll diameter: 80 mm.
