Certificate of quality Fineness % +-10.0 Initial setting time h:min +-0:45 Final setting time h:min +-10:00 Soundness Mum +-5.0 So3 % +-3.5 Mgo % +-5.0 Loss on ignition % +-5.0 Bending strength mpa +-6.5 Compressive strength mpa +-42.5 1ton/big bag
Pellets are small balls of iron ore used in the production of steel. They are made with technology that uses the powder that is generated during the ore extraction process, once considered waste. The pellets are used in the production of steel which is used in the construction of bridges, cars, planes, bicycles, household appliances and much more.
Iron ores are rocks and minerals from which metallic iron can be economically extracted. The ores are usually rich in iron oxides and vary in colour from dark grey, bright yellow, or deep purple to rusty red. The iron itself is usually found in the form of magnetite, hematite, goethite, limonite or siderite. The primary use of iron ore is in the production of iron. Most of the iron produced is then used to make steel. Steel is used to make automobiles, locomotives, ships, beams used in buildings, furniture, paper clips, tools, reinforcing rods for concrete, bicycles, and thousands of other item
GEA Varitherm VT-20 Plate Heat exchanger is made of several Varitherm-design stainless steel plates which are combined to form one effective heat transfer unit. Within each plate package the heat exchanger plates support each other at the metal-on-metal profile cross points, which ensure the stable behavior of the plate gap. The plate gasket has so called glue less sealing system. VT-20 is specially designed for cooling and heating of fluids with particle content up to a particle size of 2 mm as well as condensation of vapors, gas cooling and gas dehumidifying. This unit is in good operational condition. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width: 337 mm Length: 999 mm. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width (plates) 337 mm Length (plates): 1370 mm.
The boiler is a three-pass, fire-tube steam boiler made by Finnish Ahlström Themoflow in year 1990. The boiler has max operating pressure16 bar with 205 C steam temperature and it is equipped with exhaust gas economizer for preheating incoming feed-water and modulating heavy fuel oil burner. It's has a large 15.2 m3 water volume which allows big momentary changes in load. Other benefits include simple structure, long operating life, reliability and ease of service and maintenance. The boiler is in good operational condition. Feed water pumps and feed water tank with aerator are available for separate request and price. Technical Data: Manufacturer: Ahlström Thermoflow, Kaarina Manufacturing year: 1990 Capacity: 3.3 MW Water volume: 15.2 m3 Steam characteristics: Max 16 bar, at 205 C temperature, saturated Oil Burner: Weishaupt Monarch RMS 50/2 A - ZM (YOC 1990) Oil feeding: 140 - 490 kg/h.
Iron Ore Pellets: Pellets are small balls of iron ore used in the production of steel. They are made with technology that uses the powder that is generated during the ore extraction process, once considered waste. The pellets are used in the production of steel which is used in the construction of bridges, cars, planes, bicycles, household appliances and much more. Product Type: IRON ORE PELLETS Fe (T) 64 % Si02 1.150 % Fe0 0.75 Max Ti02 0.021% Al2O3 0.319 % Ca0 1.170 % P 0.032 % S 0.031 % V205 0.004 % Cu 0.057 % N2O 1.290 % Mg0 0.069 % CCS 309 Size 16-19 mm - 7 % 09-16 mm -91 % 06-09 mm 2 % Tumbler Index- for above 6.3 mm 96.2 % -� 95 % min Abrasion Index â??for 0.5 mm 3.8 % - � 4 % max Sticking Index @950 deg C 20.1 % Bulk Density 2.17 % Compression Strength 270 Kg / Pellet � / � 150 kg / pellet Fines below 5mm (-) 5 mm 3 % max Reducibility index 55-65 %
Manufacturer pompetravaini italy, made in year 2002. Vacuum pump is two staged rotating pump with externally located, grease lubricated bearings. Pump is liquid ring type designed for water sealed operation. The impeller and shaft are made of stainless steel (aisi 316), cast iron casing and manifold normal steel. The shaft is sealed with double mechanical seal. Pump is provided with connections for service water and draining. Pump includes also anticavitation valve. Pump is dismantled from its base frame but the delivery includes original electric motor eex classified abb hyr 200m lb 4 30 kw, 1476 rpm, year 1995. The equipment will be supplied loose - not as a skid. Technical data:trch 80 - 540/c2/ra Max suction pressure:25 mbar (till 300mbar) Max capacity:540 m3/h (min 400 m3/h) Flanges:80 mm Rotation speed:1500 rpm Power requirement:30 kw at 1500 rpm Year made:2002 Condition:fully operational
Very little operated (ony 6000 hours totally!) fuel oil fired package boiler made by Högfors (nowadays Foster Wheeler) in 1988. Complete plant with combustion air fan and feed water pumps for immediate delivery, in very good condition. Main scope of the delivery: - Högfors 30 t/h boiler - Oilon burner - Economizer - Combustion air fan - 2 pcs of 90 kW / 25 bar KSB feed water pumps - Fuel oil pumping unit made by Oilon - 8 pcs of steam shoot blowers - valves, fittings and maintenance supports . Type of boiler Water tube type with natural circulation, with two drums Manufacturer Kymin Osakeyhtiö, Högfors, Finland (Foster Wheeler) Model of the boiler: H52-47-25 bar Year of manufacturing 1980 Starting day of operation 16.11.1980 Evaporation 47 t/h saturated steam Temperature of steam 226 oC Effect 30 MW Structural pressure 25 bar Feed water temperature 120 oC Furnace volume 74,5 m3 Surface of furnace c. 136 m2 Surface of convection part 420 m2 Surface of economizer c. 504 m2 Water volume 15,8 m3 Oil Heavy oil (POR 230) Oil burner Saacke SKV, fully automatic, modulating Regulating area of burner 610-3050 kg/h Oil pumping- and pre- Oilon Osva 4000 kg/h heating station Feed water pumps 2 pcs + 1 pc as spare. KSB-centrifugal pump MOVI 65/6, massflow 59 t/h, 29,5 bar motor 90 kW, 2900 r/min Primary air fan Mercantile KDER 75, 37300 Nm3/h, motor 115 kW, 1500 r/min Sootblowers Diamond Superior sootblowers 4 pcs in boiler part Diamond Superior sootblowers 4 pcs in economizer. Dimensions of boiler part: Height 5,2 m, Width c. 4,5 m, Length 10,0 m Weight of boiler part c. 54 t. without water and accessories Weight of economizer c. 15 t. without water and accessories Boiler is suitable for gas operation by changing the burner. The boiler has been in operation only about 6.000 hours. Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Gas & HFO Boilers Wind Turbines.
ating line is delivered by Finnish Elmont Oy and it consist of 59 separate dipping tanks, 6 material handling cranes and related process and automation equipment. We have the dipping tanks and material handling cranes in our store for sale. Dipping tank materials are AISI 316, SS, PP, HST and PP. All tanks are 2200 mm long and 1250 mm height, widths varies from 450 to 1740 mm, volumes from 1213 to 4016 liters. All tanks are in good condition. The cranes are designed for those tanks and we have 6 pcs of them. Cranes have 0.25 kW gear motors and control panels. Structure is made of steel and they are in good condition. If you are looking for such equipment, please contact us and we are pleased to give you more deep information.
Good condition filtration press made ny German MSE Filterpress GmbH in year 1997. The press has 33 plates of size 630 x 630 mm, cace thickness 25 mm. Includes own hydraulic system and control cabinet. The equipment is manufactured by German MSE Filterpress GmbH, year 1997. Manufacturer’s type KFP 630-40-25K-MPN+DLMP. Structure is made on normal construction steel, plate size is 630 x 630 mm. The filter plates are pressed with single acting hydraulic cylinder with inbuilt hydraulic pump-motor. Product is fed in a central sludge feed inlet with flange connection and each pressing unit has its own outlet for the liquid filtrate which is them collected in one outlet channel. The cake will be disposed under the press. The unit has its own control panel attached to the equipment. Technical data: Manufacturer: MSE Filtterpress GmbH Year of manufacture: 1997 Manufacturers type: KFP 630-40-25K-MPN+DLMP Plate size: 630 x 630 mm Number of plates: 33 Cake thickness: 25 mm Hydraulic pressure: 380 bar max Filtration pressure: 15 bar.
The equipment is designed and manufactured by Gough & Co Ldt, UK in year 1999 / installed in 2000, manufacturer’s type single deck Vibracon GVF4. We have totally 3 identical units which were dismantled in 2007 and all of them are in very good operational condition. These are single deck circular screen design for high velocity scalping, de-watering or single deck separation in chemical and pharmaceutical industry. (These units were screening oversized particles in PVC - granulate factory truck loading station) The perforated screen and all product touching parts are made on stainless steel AISI 304L. Top deck houses the screen and the discharge spout for oversize particle removal is fitted to it. Top deck is supported with mechanical spring and vibration movement is created by two contra rotating vibrating motors on the outside of the unit so there are no internal working parts. Vibration power can be adjusted. Technical data: Type: Vibracon GVF 4 Material: AISI 304L – product touching parts Perforated screen: Mesh size 4 mm Screen diameter: 1100 mm Screen area: 9500 cm2 Vibrators: 2 x 0.52 kW units.
This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit. This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate. Machine type:Powerpak 660 Machine number:665/0211 Manufacturing year:1998 Foil type:Flexible Formatting width:430 mm Film type used:PS-PE 450/50 Max formatting depth:40 mm Forming dies:223-3,1 Capacity:10 phases / min Control unit:Tiromat Ho foil printer:SC-700 with 3 printing units Overall length:7.30 meters Overall width:1.15 meters Height:1.85 meters Nominal power need:50 A / 380 V / 50 Hz.
This laminating tunnel / convection oven is made by Swedish TRIAB / Tri Innovations AB in year 2006. The oven is designed for industrial use and in build up in two separable laminating sections, both equipped with one 40.5 kW hot air sections, one product and one return conveyors and common control unit. All product touching parts are made either of stainless steel (structures and panels) or Teflon made net belts. Convection belt (600 mm wide) is located inside of the oven tunnel and has grid type surface, the return conveyor is installed on the tunnel and it has tight waived Teflon belt. The control cabinet is attached to the equipment structures. The speed of laminating conveyor is adjusted with an inverter driven motor. The speed of return conveyor can be fine tuned via a potentiometer. The equipment is featured with a remote control possibility. This has been operating with hygienic products (material foam / polyurethane film, thickness 5 mm, max. width 450 mm and production speed 6 m/min) and is in excellent operational condition with total 3450 operating hours only and it comes with original operation manual in English language. Technical data: Made by: TRIAD / Air Innovations AB Manufacturing year: 2006 Total operating hours: 3450 Convection capacity: 2 x 40.5 kW Process control PLC: Eurotherm 2216e Hot air circulation volume: 2 x 9000 m3/h Fan electric power: 2 x 2.2 kW Temperature range: 50 – 150 C Total machine length: 10 000 mm Total machine width: 1600 mm Convection belt material: Teflon covered metal net Convection belt length: 9 000 x 600 mm Convection belt speed: 3 – 8 m/s / 0.25 kW, inverted controlled Heated width: 650 mm Inside / free height: 80 mm (from belt to nozzles) Return conveyor: Habasit FAB-8EO WV Return conveyor dimensions: 12000 x 600 mm (Teflon) Return conveyor drive: 0.25 kW, 380 V/50 Hz.
The vacuum evaporator is made by Italian Ecoteck in year 2003 and operation was stopped in early 2009 and it is in very good operational condition. This unit is made for concentrate acidic liquid wastes and therefore all liquid touching parts are made of acid proof steel ( SS 2353) or PVC. The evaporation capacity of the unit is 5000 liters / day. The unit is a complete working unit and it includes evaporator, boiler, heat pump, centrifugal pump, water-air cooler, steam ejector, control unit and all other necessary equipment to complete the unit. Operation principle: Steam rises from the boiler through a drop dispenser to the cooling unit where it condensates. The condensate drops with the gravity down to vacuum system. In-build heat pump heats up the cooling media and simultaneously cools down the condensate. Water – air cooler cools down the extra heat from the process. Necessary vacuum is generated with a centrifugal pump and a steam ejector. Condensate rejection takes place in accordance with prescheduled frequency. Technical data: Manufacturer: ECOTECH Srl Italy / Vilokan Ren Miljöteknik Sweden Type: ECO 5000 VS-HP, R407C Year made: 2003 Evaporation capacity: 5000 liters / 24 hour (pure water) Electricity consump.: about 0,15 kWh / liter pure wateri) Control unit: Siemens Micromaster 420 Compressor: Bitzer Kuhlmachinenbau GmbH, Compressor type: 6G-40,2 Compressor capacity: 126.8 m3/h, 19/28 bar Refrigenerant: R 407 C Main dimensions: 2.8 m x 1.3 m x 2.9 m Weight: 1500 kg.
Krones Toptronic K 719-555 Rotary Empty Bottle Inspector The Toptronic inspector is made for inspecting empty returnable PET bottles and empty non-returnable and returnable glass bottles. It utilizes state-of-the-art camera technology to provide precision empty container inspection. The sophisticated inspection modules detect even the tiniest damage or contamination – both in glass and PET returnable bottles. General design features Modular design Table top cover and stand cladding in stainless steel Safe bottle guidance with Raptec handling parts Blower for removing foam and lubricant residues from the container base Enclosed and air-conditioned electronics cabinet Electronic function monitoring Stop function upstream of machine infeed in response to fallen-over containers Rejection unit with retaining bar or clamping starwheel This unit has been in operation only with PET bottles sizes 0.5 liter (four different types), 1.5 liter ( two different types) 1.0 and 1.25 liter bottles and it has been in operation since 2002 and is still in very good operational condition. Handling tools for above mentioned PET bottles will be a part of delivery. Technical specification: Manufactured by: Krones AG, Germany Manufactured in: 2002 Model: K 719-555 Nominal output: up to 72000 bph Actual output: 35000 bph (with clamping starwheel) Inspection units (PET) For foreign containers P.E sensor and camera Base 1 Camera Variostation 1 Camera - sealing surface Residual liquid High frequency + infrared Side wall Camera Optimized scuffing Camera Variostation 2 Camera - Base 2 - inner side wall - full thread Variostation 3 Camera - full thread - lateral neck finish - inner side wall Variostation 4 Camera - sealing surface - lateral neck finish Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Wood Working.
Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets. More information on requests, for spam protection please introduce yourself properly. Main data of one mill: Manufacture’s type: NTK 130F/LM Year of manufacture 1988 Total operating hours: approx. 75000 Rated capacity, max: 145 kW Number of blades: 3 pcs Rotor diameter: 22 m Rotor speed: 44.5 rpm Cut-in wind speed: 4.0 m/sec Cut-out wind speed: 53 m/sec (120 mph) Hub height: 26 m Generator: ASEA 145 kW / 1500 rpm / 50 Hz Blade type: LM 9.7 m H/H/T diam. 21 m Gear box type: Lohman & Stolterfort GPC 145 Clutch type: Lohr & Brokamp Universal Joint No 105 Total weight: 15200 kg.
Yogurt production and packaging line 4000 l / shift 0732010 Yogurt production and packaging line 4000 l / shift Yogurt production equipment consists of 4 pcs 1000 liters of yogurt fermentation tanks, transmission equipment and a fully automated filling line 150 - 200 grams plastic cups. Process operation requires two people and equipment can be made about 4000 liters (or 20000 pieses) of 200g canned yogurt cups or other similar product for a normal 8-hour working shift. Packaging equipment is manufactured in the 1980s by German Ganzhorn & Stirm (nowadays Casti) and an automatic product cup feeder has been added later on the line. Also the tray feeding device has been recently added. The production line is fully operational and suitable besides for yogurt production, also for all curdled / fermented milk packaging in 150g-200g cups. Fermentation tanks are double walled 1000 liter stainless steel vertical tanks. The product temperature can be adjusted as desired (e.g.36C) by using heating water between double walls. Control valves are manually adjusted. The fermented yogurt is transferred to two 100 liter feeding tanks of the packing line with gentle rotary lobe pumps. Filling the yogurt cups is fully automated 2-lane packing process. The main equipment are manufactures by German Canzhorn & Srimin. Later installed automatic cup feeding equipment places 150 gr - 200 gr cups in 2 rows on the filling machine. The filling machine fills cups in three phases; first to the bottom desired volume of jam and then two different layers of product mass. ( 3-layer of yogurt). The cups are closed with aluminum lids which is sealed with electric heater. Transfer conveyor moves closed cups on to a palletizing machine which loads 20 cups on each cardboard or plastic tray (tray is automatically fed by a tray feeding device) where full trays are moved to a stacker machine which piles several layers of trays (up to 1 meter tall) for transportation. Technical Specifications: The manufacturer: Ganzhorn & Stirm (Casti) Filling machine type: DOGatherm 61 Stacker type: BE 75/2 Production capacity: up to 4000 liters / shift Yogurt fermentation tanks: 4 x 1000 liters Cups & filling: 150 - 200 g / max. 3-layer filling Filling line length: about 12 meters.
Rotary Lube Blower / Vacuum compressor KAESER EB 420 C û 38 m3/min, 53 kPa There are two identical sets of oil-free, 2 lobe rotary blowers, made by Germand Kaeser Kompressoren GmbH in year 2005 with accessories. Manufactures type is Kaeser ED 420 Compact Omega Pluss 53 and accessories include a control cabinet with two inverters and programmable Kaeser Start Control STC 30 unit, totally 6 preliminary intake air filters and 3 final air intake filters with their steel supports. The rotary blower units have removable sound enclose for noise insulation. Operation of the equipment was stopped in year 2007, total running hours approx 7000 and therefore they are in excellent operational condition. In addition, we can offer you service maintenance by the manufacturer at separate cost. This equipment is suitable for demanding dust collection and pneumatic transportation of various products due to oil free operation. For pneumatic transport application some changes in filters and other parts are needed. The rotary lobe has two blower shafts with high efficiency Omega profile in a blower block. The rotary lobe and the block have a very small distance and they are not touching each other's and therefore there is no need for lubrication oil. The rotors are driven by high efficiency electric motor via belt connection and they both are installed on the same base frame. . The inlet and discharge silencers are designed to be effective at all frequencies and are eminently suited to variable speed . Higher rotational blower speeds produce high volumetric efficiencies, which in turn lower discharge temperatures and power consumption. The Compact Range ensures that all serviceable items are accessed from the front panels of enclosures. The preliminary intake air filters are combination of cyclone and bag filter and it removes most of the dust from inlet air. Fine filter is a combination of cyclone and 138 ceramic fine filters which removes fine dust very effectively. Technical Data Manufacture's type: EB 420 Compact Omega plus 53 Manufactured in year: 2005 Suction capacity with max vacuum:38,0 m3/min Power demand max: 40,3 kW Rotor's rotation speed 4120 rpm Max suction vacuum: 0,53 bar (abs.) Discharge pressure: 1,0 bar (abs.) Max pressure increase: 470 mbar Temperature rise max -t: 82 K Electric motor: 45 kW û 50 Hz / 400/690V û 83/48 A Electric motor nominal speed:2965 rpm Protection class: IP 55 Inverters: Mitsubishi FR-F740-01160-EC Case ventilation fan: 370 W û 50 Hz / 230 / 400V Weight blower with the case:1120 kg Blower case main dimensions:1.8 x 1.7 x 1.8 m (K x L x S) Noise level: 99 dB (A) Noise level with the case: 84 dB (A).
Tyre scrap.
Tyre reclaim rubber fine and recycle tyres.
