The recovery plant is specially designed to recover CO2 from fermentation processes at breweries. This complete CO2 plant was installed in 2001 and it has nominal CO2 removal capacity of 1000 kg/h. The plant has Siemens S 7 control system where operation is carried our via a large 12 " color screen panel with Windows CE operating system. This is a complete CO2 recovery plant and final delivery scope depends on buyers needs. The plant has been in operation only approx 5 years and is still installed and in very good condition. The carbon dioxide plants was designed by Danish Union Engineering (www.union.dk ) and the delivery includes following main components: - 1 Scrubber for gas flushing - 2 Foam catcher vessels - CO2 collection, inflammable - 2 Mehrer TZW 70 CO2 compressors - 2 Carbon filters - 2 Dehydrators - CO2 Liquefier - CO2 Storage Tank - 2 Cooling compressors GEA Grasso GD-3 for R717 - Air cooled condenser for NH2 compressors - Alarm center for CO2 and NH3 concentration - Station for 40 kg CO2 still tank filling - CO2 pumping station from a truck to the factory - CO2 purification tester - Steam heated evaporator for liquid CO2 Detailed technical information available for serious buyers
Manufacturer pompetravaini italy, made in year 2002. Vacuum pump is two staged rotating pump with externally located, grease lubricated bearings. Pump is liquid ring type designed for water sealed operation. The impeller and shaft are made of stainless steel (aisi 316), cast iron casing and manifold normal steel. The shaft is sealed with double mechanical seal. Pump is provided with connections for service water and draining. Pump includes also anticavitation valve. Pump is dismantled from its base frame but the delivery includes original electric motor eex classified abb hyr 200m lb 4 30 kw, 1476 rpm, year 1995. The equipment will be supplied loose - not as a skid. Technical data:trch 80 - 540/c2/ra Max suction pressure:25 mbar (till 300mbar) Max capacity:540 m3/h (min 400 m3/h) Flanges:80 mm Rotation speed:1500 rpm Power requirement:30 kw at 1500 rpm Year made:2002 Condition:fully operational
Compressors units (totally 4 pcs) are built by York Sabroe in 2002 and 2003 and they operate with R22 refrigerant. Two identical SAB 128 HF screw compressor units are built on a common base frame with an integrated horizontally mounted oil separators, oil circulation pumps and local operating panels. Common (for two compressors) plate type Freon / Glycol evaporator, internal glycol circulating pump and one large Freon buffer tank is also build on the same base frame. Delivery includes also evaporative condenser and LV / Control cabinet and external glycol circulating pump. Above described 2 x SAB 128 HF packages we have two for sale, one made in year 2002 and the other year 2003. Both packages are still installed and can be tested in mutually agreed time. Units have been in operation approx 6 years and 5 years and they are in very good condition. Technical data Number of compressors - 4 pcs Compressor type - SAB 128 HF Refrigerant - R 22 Cooling capacity - 4 x 379 kW ( 0 /+40C) Swept volume - 4 x 454 m3/h Electric drives (compressor) 4 x 110 kW - 400/690 V 50Hz (also suitable for 60Hz) Freon buffer tank -2 x 1650 liters Plate evaporators - Alfa-Laval M10-BW FGR Evaporative condensers - 2 x BAC VXC 116 Closed Circuit Condenser fans - 1 x 17 kW and 1 x 4 kW for each Condenser circulating pumps- 2 x Grundfors LP80 - 25/133 Glycol pumps - 2 x Grundfors LP 80 - 25/133 2 x Hilge Mahana 65-160
Rotary Lube Blower / Vacuum compressor KAESER EB 420 C û 38 m3/min, 53 kPa There are two identical sets of oil-free, 2 lobe rotary blowers, made by Germand Kaeser Kompressoren GmbH in year 2005 with accessories. Manufactures type is Kaeser ED 420 Compact Omega Pluss 53 and accessories include a control cabinet with two inverters and programmable Kaeser Start Control STC 30 unit, totally 6 preliminary intake air filters and 3 final air intake filters with their steel supports. The rotary blower units have removable sound enclose for noise insulation. Operation of the equipment was stopped in year 2007, total running hours approx 7000 and therefore they are in excellent operational condition. In addition, we can offer you service maintenance by the manufacturer at separate cost. This equipment is suitable for demanding dust collection and pneumatic transportation of various products due to oil free operation. For pneumatic transport application some changes in filters and other parts are needed. The rotary lobe has two blower shafts with high efficiency Omega profile in a blower block. The rotary lobe and the block have a very small distance and they are not touching each other's and therefore there is no need for lubrication oil. The rotors are driven by high efficiency electric motor via belt connection and they both are installed on the same base frame. . The inlet and discharge silencers are designed to be effective at all frequencies and are eminently suited to variable speed . Higher rotational blower speeds produce high volumetric efficiencies, which in turn lower discharge temperatures and power consumption. The Compact Range ensures that all serviceable items are accessed from the front panels of enclosures. The preliminary intake air filters are combination of cyclone and bag filter and it removes most of the dust from inlet air. Fine filter is a combination of cyclone and 138 ceramic fine filters which removes fine dust very effectively. Technical Data Manufacture's type: EB 420 Compact Omega plus 53 Manufactured in year: 2005 Suction capacity with max vacuum:38,0 m3/min Power demand max: 40,3 kW Rotor's rotation speed 4120 rpm Max suction vacuum: 0,53 bar (abs.) Discharge pressure: 1,0 bar (abs.) Max pressure increase: 470 mbar Temperature rise max -t: 82 K Electric motor: 45 kW û 50 Hz / 400/690V û 83/48 A Electric motor nominal speed:2965 rpm Protection class: IP 55 Inverters: Mitsubishi FR-F740-01160-EC Case ventilation fan: 370 W û 50 Hz / 230 / 400V Weight blower with the case:1120 kg Blower case main dimensions:1.8 x 1.7 x 1.8 m (K x L x S) Noise level: 99 dB (A) Noise level with the case: 84 dB (A).
ELMO-G Blower - Vacuum pump 1000 m3/h The blowers are made by German ELMO Vacuum Technology GmbH, a Siemens company in year 2002 and they are single stage, gas ring type. The vacuum pumps are in good operational condition. We have three identical pump units and originally the pumps were in dust suction operation and therefore the delivery includes 3 pcs high efficiency cyclone type dust filter with electric discharge vibrators. Motor speed is controlled with individual inverters. Units can be sold separately. ELMO-G vacuum pumps can be used for suction operation or as compressors in pneumatic transportation system. They have side-channel principle using gas ring as a sealing and the gas flows through the compressor along a helical trajectory and is repeatedly accelerated and thereby repeatedly compressed according to the required operating point. The blowers are oil-free and thus suitable for various applications. The blowersÆ have both suction and discharge noise silencer. For pump curves, both in suction and compression, as well as additional information please contact us. Technical Data: Manufacturer's type:ELMO 2BH1943-1GC36 Year of manufacture:2002 Suction capacity with max vacuum:16,7 m3/min (50Hz) Suction capacity with max discharge pressure:21,5 m3/min (50Hz) Max pressure difference in vacuum operation:0,30 bar (50 Hz) Max pressure difference in compression operation:0,35 bar (50 Hz) Inverter:Danfors VTL 6000 HVAC Blower's rotation speed2920 rpm / 50 Hz and 3520 rpm / 60 Hz Electric motor (Siemens):50 Hz: 21.0 kW û 300/690V û 39.5 / 23.0 A 60 Hz: 24.2 kW û 460 V û 41.0 A Protection class:IP 54.
Industrial Crane Konecranes CTX 10 t, Dual Bridge with 33.6 m span The crane was manufactured by Konecranes Oyj in 2001 and the operation was stopped in year 2006. The equipment was regularly serviced by the manufacturer and is thus in excellent operating condition. The crane is still installed in its original place and can be tested on any time. The double bridge is welded housing construction equipped with one double speed wire hoists and a motorized rail equipment on both ends. The crane has both the local wire connected control unit as well as the wireless remote controller. On the bridge there is a service platform and the local LV û and control cabinet. All electric motors are dimensioned in accordance with Industrial Heavy Duty ED classification. The equipment includes the crane moving rail which will be sold separately. Technical data: Manufacturer's type:CXTD10t x 33.6m Hol: 6.1m Lifting capacity:10 000 kg Span distance:33.55 m Lifting class:FEM M5 (2m) Bridge structure:Welded case Total weight:Approx 22 000 kg Type of wire hoist:XL 404N40BDA4 Lifting height:6.1 m Lifting speeds:8.0 and 1.3 m / min Wire hoist speeds:32 and 8 m / min Bridge speed:Inverter controlled, max 40 m / min Wire hoist lifting motor:Double power 15 and 2.5 kW (60% ED) Wire hoist moving motors:2 x 0.65 kW (40% ED) Bridge moving motors:2 x 1.8 kW (40% ED) Total power need:19.9 kW / 400 V / 50 Hz Crane moving rail:60 x 40 cm, length 2 x 140 m.
Compressor single stage, standard speed oil-injected rotary screw compressor with manufactured by German company Drucklufttechnik GmbH in year 2002. The complete unit consists of intermediate pressure vessel and Ultratroc - air dryer all delivered same time as the compressor. The unit is controlled by modern DELCOS 3000 control unit. The total unit has 30320 operating hours, the unit has been regularly serviced by a compressor service company and is in good operational condition. The compressor is single-stage, double screw, V-belt driven electric motor drive compressor which has oil cooler and thermostat controlled water - air after cooler on discharge of the pressurized air. The operations were stopped in year 2006 but the compressor and other equipment are still installed and ready for test run. Technical data: Compressor type:CompAir L90 7,5A Capacity:16.1 m3/min, 7.5 bar Comp. electric motor:90 kW - 400/415 V û 50 Hz Air cooler electric motor:3.0 kW - 400/415 V û 50 Hz Compressor weight:2380 kg Compressor dimensions:2.4 x 1.4 x 2.0 m (W x L x H) Air dryer type:Ultratroc SD 1350 û type 422 Air dryer air volume:22.5 m3/min Total power requirement of dryer:2.4 kW DryerÆs refrigerant:Type R134 a û filling 3.5 kg DryerÆs dimensions:1200x900x800 mm, weight 185 kg Int. mediate air pressure vessel:Volume 2 m3, 10 bar, made by Galvanoimis Oy.
The fan is made by German Pollrich Ventilatoren GmbH in year 2004 and it has been as a back-up emergency fan which has practically newer used and therefore the unit is new like condition. This fan was designed to blow explosive air/gas mixture (VOC) and therefore it fulfills category II 2G, temperature class 1 ATEX 95 norm of explosive proof design. The motor and fan are built on a common heavy duty frame and they are connected with a flexible coupling. Technical data: Manufacturer: Pollrich Ventilatoren GmbH Year of manufacture: 2004 Fan type: VR50S11C1UK0900LG360MMUU Manufacturing no: 123665 Volume: 10.55 m3/sec (37980 m3/h) Max press difference: 8000 Pa (0.08 Bar) Speed: 2980 RPM Max gas temperature: 80 C Power requirement: 104.6 kW Electric motor: CEMP 132 kW / 2970 RPM Type: AC70 315M 2 Classifications: II 2 G EEXd IIC T4 IP 55.
This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit. This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate. Machine type:Powerpak 660 Machine number:665/0211 Manufacturing year:1998 Foil type:Flexible Formatting width:430 mm Film type used:PS-PE 450/50 Max formatting depth:40 mm Forming dies:223-3,1 Capacity:10 phases / min Control unit:Tiromat Ho foil printer:SC-700 with 3 printing units Overall length:7.30 meters Overall width:1.15 meters Height:1.85 meters Nominal power need:50 A / 380 V / 50 Hz.
The boiler is a three-pass, fire-tube steam boiler made by Finnish Ahlström Themoflow in year 1990. The boiler has max operating pressure16 bar with 205 C steam temperature and it is equipped with exhaust gas economizer for preheating incoming feed-water and modulating heavy fuel oil burner. It's has a large 15.2 m3 water volume which allows big momentary changes in load. Other benefits include simple structure, long operating life, reliability and ease of service and maintenance. The boiler is in good operational condition. Feed water pumps and feed water tank with aerator are available for separate request and price. Technical Data: Manufacturer: Ahlström Thermoflow, Kaarina Manufacturing year: 1990 Capacity: 3.3 MW Water volume: 15.2 m3 Steam characteristics: Max 16 bar, at 205 C temperature, saturated Oil Burner: Weishaupt Monarch RMS 50/2 A - ZM (YOC 1990) Oil feeding: 140 - 490 kg/h.
Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets. More information on requests, for spam protection please introduce yourself properly. Main data of one mill: Manufacture’s type: NTK 130F/LM Year of manufacture 1988 Total operating hours: approx. 75000 Rated capacity, max: 145 kW Number of blades: 3 pcs Rotor diameter: 22 m Rotor speed: 44.5 rpm Cut-in wind speed: 4.0 m/sec Cut-out wind speed: 53 m/sec (120 mph) Hub height: 26 m Generator: ASEA 145 kW / 1500 rpm / 50 Hz Blade type: LM 9.7 m H/H/T diam. 21 m Gear box type: Lohman & Stolterfort GPC 145 Clutch type: Lohr & Brokamp Universal Joint No 105 Total weight: 15200 kg.
e equipment was manufactured by Jeffrey Rader AB, Sweden in 1995 and it is in very good operational condition. It consist of two heavy duty rolls with removable profilied surfaces which rotate towards each other and presses overzised wood chips between the profiles. Roll drives 2 x 110 kW / 1500 rpm connected with two gearboxes. Hydraulic pump 7.5 kW, capacity 220 m3/h wood chips. The equipment was manufactured by Jeffrey Rader Inc, Sweden in year 1995, manufacturers type is DynaYield 80-300 and it is in good operational condition. The Chip Conditioner consists of two heavy duty rolls with removable profiled surfaces. They rotate towards each other and pull the oversize chips between them. The profiled surfaces are aligned so that the pyramid apexes on one roll travel in the valleys of the apexes on the adjacent roll. With normal oversize wood, the Conditioner typically generates less than 1% fines and 3% pins The normal application for the Chip Conditioner is in a chemical pulping process, processing the oversize materials by fissuring the wood chips parallel with the grain to allow the cooking liquors to penetrate the chip, and allow the oversize chip to cook as an acceptable size chip. Another application is in a thermo-mechanical pulping process (TMP), as a preconditioning An important feature of this machine is its ability to handle small portions of tramp without going off-line. With the so called Dynagage Conditioner, the dynamic roll is allowed to move away from the static roll, and once the tramp is through the unit, the roll automatically moves back to the proper set point without shutting down the flow and together with slow rotation speed enable were low down time and maintenance costs. Roll distance movements are made with a hydraulic system build on the equipment and controlled by 3 position sensors More information on requests, for spam protection please introduce yourself properly. Technical data: Model: RDY 80-300 Manufacturing year: 1995 Capacity (throughput): 220 m3/h loose wood chips Press roll diameter: 915 mm Roll length: 2440 mm Roll motors: 2 x 110 kW / 1500 rpm / 690 V – 50Hz Press distance between the rolls: 2.2 mm Gearboxes: 2 x Kipo Benzler TV 512 Hydraulic pump: Rexroth 200 bar with Mecman syliders Electric motor for hydraulic pump: ASEA 7.5 kW Weight: 33 000 kg Length: 5083 mm Width: 2550 mm Height: 2400 mm.
Krones Toptronic K 719-555 Rotary Empty Bottle Inspector The Toptronic inspector is made for inspecting empty returnable PET bottles and empty non-returnable and returnable glass bottles. It utilizes state-of-the-art camera technology to provide precision empty container inspection. The sophisticated inspection modules detect even the tiniest damage or contamination – both in glass and PET returnable bottles. General design features Modular design Table top cover and stand cladding in stainless steel Safe bottle guidance with Raptec handling parts Blower for removing foam and lubricant residues from the container base Enclosed and air-conditioned electronics cabinet Electronic function monitoring Stop function upstream of machine infeed in response to fallen-over containers Rejection unit with retaining bar or clamping starwheel This unit has been in operation only with PET bottles sizes 0.5 liter (four different types), 1.5 liter ( two different types) 1.0 and 1.25 liter bottles and it has been in operation since 2002 and is still in very good operational condition. Handling tools for above mentioned PET bottles will be a part of delivery. Technical specification: Manufactured by: Krones AG, Germany Manufactured in: 2002 Model: K 719-555 Nominal output: up to 72000 bph Actual output: 35000 bph (with clamping starwheel) Inspection units (PET) For foreign containers P.E sensor and camera Base 1 Camera Variostation 1 Camera - sealing surface Residual liquid High frequency + infrared Side wall Camera Optimized scuffing Camera Variostation 2 Camera - Base 2 - inner side wall - full thread Variostation 3 Camera - full thread - lateral neck finish - inner side wall Variostation 4 Camera - sealing surface - lateral neck finish Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Wood Working.
Yogurt production and packaging line 4000 l / shift 0732010 Yogurt production and packaging line 4000 l / shift Yogurt production equipment consists of 4 pcs 1000 liters of yogurt fermentation tanks, transmission equipment and a fully automated filling line 150 - 200 grams plastic cups. Process operation requires two people and equipment can be made about 4000 liters (or 20000 pieses) of 200g canned yogurt cups or other similar product for a normal 8-hour working shift. Packaging equipment is manufactured in the 1980s by German Ganzhorn & Stirm (nowadays Casti) and an automatic product cup feeder has been added later on the line. Also the tray feeding device has been recently added. The production line is fully operational and suitable besides for yogurt production, also for all curdled / fermented milk packaging in 150g-200g cups. Fermentation tanks are double walled 1000 liter stainless steel vertical tanks. The product temperature can be adjusted as desired (e.g.36C) by using heating water between double walls. Control valves are manually adjusted. The fermented yogurt is transferred to two 100 liter feeding tanks of the packing line with gentle rotary lobe pumps. Filling the yogurt cups is fully automated 2-lane packing process. The main equipment are manufactures by German Canzhorn & Srimin. Later installed automatic cup feeding equipment places 150 gr - 200 gr cups in 2 rows on the filling machine. The filling machine fills cups in three phases; first to the bottom desired volume of jam and then two different layers of product mass. ( 3-layer of yogurt). The cups are closed with aluminum lids which is sealed with electric heater. Transfer conveyor moves closed cups on to a palletizing machine which loads 20 cups on each cardboard or plastic tray (tray is automatically fed by a tray feeding device) where full trays are moved to a stacker machine which piles several layers of trays (up to 1 meter tall) for transportation. Technical Specifications: The manufacturer: Ganzhorn & Stirm (Casti) Filling machine type: DOGatherm 61 Stacker type: BE 75/2 Production capacity: up to 4000 liters / shift Yogurt fermentation tanks: 4 x 1000 liters Cups & filling: 150 - 200 g / max. 3-layer filling Filling line length: about 12 meters.
Stainless Steel Tank 3.5 m3, with variator driven mixer 3pcs excellent condition vertical stainless steel (food quality) tanks with electric motor driven and mechanical variotor speed controlled heavy duty two plade mixer. The tanks are made by Finnish Tankki Oy in 1992, they have are standing on 3 heavy legs, liguid volume 3.5 m3, conical bottom for easy discharge. Necessary service man door and other connections for venting, filling and discharging. Total height: 3.4 m (+ motor and connections 50 cm) Diameter of the tank: 1.6 m Wall height: 1.8 Mixer: Sew-Eurodrive KAF76-D34 Mixer rpm: 12.2 - 60 rpm Moment: 900 - 400 Nm Electric motor 3.0 kW / 1400 rpm.
Drum and Container Filling Line, Semiautomatic YOC 2006 The line is designed for filling both 1000 liter IBC’s and normal 209 liter drums / barrels. It consist of straight chain driven heavy duty roller conveyor which is carrying IBC’s or a standard pallet loaded with four drums / barrels through the filling process and conveying them for further storing. The filling machine is semiautomatic coarse-and-fine filling station; first is programmable volumetric and then fine filling with integrated weighing system. Cap closing / bunging and sealing will be made manually but a machine aided. The station operation is controlled by Siemens S7C programmable logic. The line is manufactured in 2006 by Finnish company “Insinööritoimisto Jyrki Kekälainen” who is specialized supplying automation solutions filling and packing applications. Operation description: The operator lifts the empty containers on the conveyor (open the cap of container), the container will move into filling machine and it will be filled automatically with 2 "and 1 / 2" valves, coarse-and fine-filling. After filling the container will move out of the machine and the operator will fix the label and close the cap. After the filling station there is ~16 m long puffer conveyor for the filled IBC`s, where a fork lift will pick up the IBC`s In drum filling the operator lifts the empty drums on pallet (open the caps). Then he lifts the pallet on the conveyor. In the machine there is an extra filling lence for the drums. The drums are filled on the weighing system of the machine which is controlling the filling of each barrel. After the drum is filled the operator move the lence into second drum and machine start to fill it. After all drums are filled the pallet will move out of machine and the operator will close the caps and fix the seals and labels. Technical data: Manufactured in: 2006 Suitable for: Standard IBC and Drums Max filling weigh: 1500 kg Filling accuracy: 0.5 kg Filling capacity: 7 IBC/hour or 35 Drums (209 liters) / hour Roller conveyor type: Chain Driven, Galvanized Roller conveyor length: Approx 16 meters Roll diameter: 80 mm.
GEA Varitherm VT-20 Plate Heat exchanger is made of several Varitherm-design stainless steel plates which are combined to form one effective heat transfer unit. Within each plate package the heat exchanger plates support each other at the metal-on-metal profile cross points, which ensure the stable behavior of the plate gap. The plate gasket has so called glue less sealing system. VT-20 is specially designed for cooling and heating of fluids with particle content up to a particle size of 2 mm as well as condensation of vapors, gas cooling and gas dehumidifying. This unit is in good operational condition. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width: 337 mm Length: 999 mm. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width (plates) 337 mm Length (plates): 1370 mm.
Very little operated (ony 6000 hours totally!) fuel oil fired package boiler made by Högfors (nowadays Foster Wheeler) in 1988. Complete plant with combustion air fan and feed water pumps for immediate delivery, in very good condition. Main scope of the delivery: - Högfors 30 t/h boiler - Oilon burner - Economizer - Combustion air fan - 2 pcs of 90 kW / 25 bar KSB feed water pumps - Fuel oil pumping unit made by Oilon - 8 pcs of steam shoot blowers - valves, fittings and maintenance supports . Type of boiler Water tube type with natural circulation, with two drums Manufacturer Kymin Osakeyhtiö, Högfors, Finland (Foster Wheeler) Model of the boiler: H52-47-25 bar Year of manufacturing 1980 Starting day of operation 16.11.1980 Evaporation 47 t/h saturated steam Temperature of steam 226 oC Effect 30 MW Structural pressure 25 bar Feed water temperature 120 oC Furnace volume 74,5 m3 Surface of furnace c. 136 m2 Surface of convection part 420 m2 Surface of economizer c. 504 m2 Water volume 15,8 m3 Oil Heavy oil (POR 230) Oil burner Saacke SKV, fully automatic, modulating Regulating area of burner 610-3050 kg/h Oil pumping- and pre- Oilon Osva 4000 kg/h heating station Feed water pumps 2 pcs + 1 pc as spare. KSB-centrifugal pump MOVI 65/6, massflow 59 t/h, 29,5 bar motor 90 kW, 2900 r/min Primary air fan Mercantile KDER 75, 37300 Nm3/h, motor 115 kW, 1500 r/min Sootblowers Diamond Superior sootblowers 4 pcs in boiler part Diamond Superior sootblowers 4 pcs in economizer. Dimensions of boiler part: Height 5,2 m, Width c. 4,5 m, Length 10,0 m Weight of boiler part c. 54 t. without water and accessories Weight of economizer c. 15 t. without water and accessories Boiler is suitable for gas operation by changing the burner. The boiler has been in operation only about 6.000 hours. Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Gas & HFO Boilers Wind Turbines.
Double floor tool storage made of removable metal structure. Walls on 3 sides of the storage, one side is main building wall. Includes two lockable separate storage rooms and selves. Free height in lower level is 2.7 meters. Material is steel and aluminum. Will be sold as is where is bases.
Plasmatreat FG1002 pre-treatment and cleaning unit This flat surface pre-treatment and cleaning unit with open air / atmospheric-pressure plasma technology was originally made by Plasmatreat company in 2004, manufacturer's model FG1002 with Siemens PLC control system and then in year 2008 it was refurbished with new plasma nozzle directing robot and an aluminium profile structured operation table. The unit has two plasma nozzles and it has been used on occasionally and is in excellent condition. The equipment has CE marking and proper documentation, including wirering diagrams This machine is designed to pre-treat and clean any metal, aluminum, plastics (such as PP and EPDM) or glass surface free from grease, dust and other unwanted materials and to pre-treat material surface for ensuring the adhesion of surface coating to these materials. Plasmatreat process also allows to use environmentally friendly water-based painting for coating and due to the fact that cleaning with plasma is a dry process immediate further processing of the materials is possible. For more information, please visit manufacturer's web page www.plasmatreat.de Technical information: Manufacturer:Plasmatreat Company Model:Plasmatreat Openair® FG 1002 Serial number:695 Year of manufacturing:2004 / 2008 Operation table size:1600 x 3000 mm Electricity connection:3~/ 400V / 32 A Condition:Used, excellent.
