In short, limestone and other materials containing calcium, silicon, aluminum and iron oxides are crushed and milled into a raw meal. This raw meal is blended and then heated in the pre-heating system to start the dissociation of calcium carbonate to oxide. The meal goes further into the kiln for heating and reaction between calcium oxide and other elements to form calcium silicates and aluminates at t a temperature up to 1450 centidegree: so called clinker burning. The cyclone system is attached to the rotary kiln by a riser duct. Secondary fuel is fed to the riser duct, the main fuel mixture, coal/petcock, fires the kiln. Reaction products leave the kiln as a nodular material called clinker. The clinker will be interground with gypsum and other materials to cement.
Cement plant
Cement mill
Natural Foods And Beverages, Edible Oils, Ginger, Garlic, Apples, Lemons, Oranges, Mandarins, Avocado, Fruits And Vegetables, Cement Clinker, Gypsum, Salt, Portland Cement, Cement Aggregates Such As Gravel, Crusher Run, Chemical, Food Additives, New Energy Products (ups, Outdoor Energy Storage Power Supply, Solar Panels, Generators, Portable Power Stations, Power Conversion Devices, Wood And Wood Waste, Charcoal Etc),.
Lithium hydroxide can be used as developing agent and lubricating oil for spectral analysis The additive of alkaline battery electrolyte can increase the electric capacity by 12 to 15 and increase the service life by 2 to 3 times It can be used as an absorbent for carbon dioxide and can purify the air in submarines The chemical equation is 2LiOHsCO2gLi2CO3sH2Ol It is used to make lithium salt and lithiumbased grease electrolyte of alkaline battery absorption liquid of lithium bromide refrigerator etc used in petroleum chemical industry light industry nuclear industry etc When used in alkaline batteries the aluminum content is not more than 006 and the lead content is not more than 001 It is used as an analytical reagent a photographic developer and also in the manufacture of lithium it is used as a raw material for the preparation of lithium compounds It can also be used in metallurgy petroleum glass ceramics and other industries Lithium hydroxide is mainly consumed for the production of lithium greases A popular lithium grease is lithium stearate which is a generalpurpose lubricating grease due to its high resistance to water and usefulness at both high and low temperatures Carbon dioxide scrubbing Lithium hydroxide is used in breathing gas purification systems for spacecraft submarines and rebreathers to remove carbon dioxide from exhaled gas by producing lithium carbonate and water It is used as a heat transfer medium and as a storagebattery electrolyte It is also used in ceramics and some Portland cement formulations Lithium hydroxide isotopically enriched in lithium7 is used to alkalize the reactor coolant in pressurized water reactors for corrosion control
Our paper bag production line consists two parts, one is paper tube making machine, another is bottom pasting machine. This production line can make 2-4 color printing, bottom valved paper bags. This kind of bags can be used for packing cement, mortar, chemicals materials and other granule or powder materials. Bags can be 2~4 layers kraft paper or clupak paper and one layer of PE material. 1) HT series paper tube making machine can produce multi-ply paper tube. Material paper reels being unwinding automatically, multi-layers paper tube will be formed automatically. Perforation, tearing down, tension control, deviation rectifying, counting is controlled automatically. A multi-color flexo printing machine is connected with this machine, paper tube can get 2-4 color printing. 2) HD series bottom pasting machine does pasting work to the paper tube. Bottom of paper tube can be folded automatically and pasted with glue, another end of tube also will be glued and valve patches can be pasted at this end. This machine can paste different kinds of valve patches at the bottom of bag. Technical specification: Tube length: 620mm~1200mm Tube width: 340mm~600mm Width of the paper roll: 780~1120mm Max Diameter of the roll: 1300mm Compressed air: 0.7 m3/min Capacity: 120 pieces/min Power: 19.5KW Number of ply: 2(or 4) Color printed: 2(or 4) Ink: Water-based ink
According to our current manufacturability, we can supply all the major equipments in a cement production line with daily production no more than 6000 ton. We can manufacture ¦µ4.8m¡á74m¡¢¦µ4.5m¡á66m¡¢¦µ4.3m¡á66m¡¢¦µ4.2m¡á60m series of cement rotary kiln, ¦µ4.6m¡á10.5+3.5m drying mill, ¦µ4.2m¡á13m cement mill, vertical mill series and other matching equipment in a cement production line. In short, we can make you your own cement production line. From this page, you can get the lime kiln, ball mill, complete set of cement machinery, cement equipment, ceramic ball mill, ball mill. If you are interested in our products, please contact us by e-mail or telphone, thank you.
Cement production line
1000-10000 tpd cement production line Cement production line mainly includes crushing and pre homogenization, homogenization of raw material preparation, preheating decomposition, cement clinker, cement grinding and packaging process. Keyuan machinery has the ability of cement production line independently constructed 1000 t/d-10000 t/d, and has built a rich design experience, the construction of a cement production line of large projects. The production line adopts the new dry process cement preparation process, reduces power consumption by 20% - 30%, greatly reduces the production cost, improve the comprehensive benefit of enterprises. Yield: 1000 t/d-10000 t/d.Please contact me with shuguang9800 at 163 dot com.. Output: 55~250 t/h Ratio surface area: 3300~3800 cm2/g Grinding diameter: 3000~5600 mm System power consumption: 25~30 kwh/t
Uses: Grouting and fixing of equipment foundation. Grouting and fixing of anchor bolt. Grouting and fixing of structural steel column soleplate. Installation and fixing of bridge pot rubber bearing. Grouting and fixing of bridge expansion joint. Grouting and fixing of wind power base and pre-stressed Tensioned anchor bolt. Installation and fixing of rail spike. Installation and fixing of various structural components. Grouting and fixing of beams and columns section-increasing And shear wall-thickening. Instructions: Recommended mechanical mixing, strictly no manual drill Mixer. Recommended amount of mixing water: 12~14%. 25kg/bag
1 Size3.09m 2 Capacity5055t/h(closed circuitfeeding size25mmfeeding moisture0.5produce fineness 4900) 3 Rotary speed19.13r/min 4 Grinding medium load76t 5 Main motor modelyr1000-8/1180power:1000kwvoltage6kv/10kv 6 Main reducermby800 i=6.3 7 Auxiliary motor modelyej200l1-6power18.5kwrotary speed970r/min 8 Auxiliary reducer modelzsy250i, speed ratioi=l00 9 Cooling methodwater 10 Lubrication methodthin oil station(GYXZ-25A) (1) Low pressure system Oil flow25l/min oil pressure0.4mpa, pump modelcb-b63 Oil heating temperature40 Motor modely112l-6 1.1kw (2) High pressure system Pump mpdel2.5mcy14lb Oil flow2.5l/min Oil pressure32mpa Motory112m-6 2.2kw 11machinery weight154.3t excluding motor and reduceR.
The structure of kiln is simple, operate conveniently and reliably in life, less wearing parts, high rate of operation, it is the equipment to calcine high-grade cement in cement plant. Meanwhile, it is also widely used in metallurgical, chemical, construction and other industries. The rotary kiln produced by my company is with strong structure, operation smooth, high-quality products etc and can provide users with advanced high-performance vertical pre-heater, 5 degree cyclone pre-heater. Cement manufacturing consists of raw material grinding, blending, pre-calcining, clinker burning and cement grinding. In short, limestone and other materials containing calcium, silicon, aluminum and iron oxides are crushed and milled into a raw meal. This raw meal is blended and then heated in the pre-heating system to start the dissociation of calcium carbonate to oxide. The meal goes further into the kiln for heating and reaction between calcium oxide and other elements to form calcium silicates and aluminates at t a temperature up to 1450 centidegree: so called clinker burning. The cyclone system is attached to the rotary kiln by a riser duct. Secondary fuel is fed to the riser duct, the main fuel mixture, coal/petcock, fires the kiln. Reaction products leave the kiln as a nodular material called clinker. The clinker will be interground with gypsum and other materials to cement. The equipments we use in this whole production line are vibrating feeder, jaw crusher, impact crusher, cement ball mill, lifer, preheating system, cement rotary kiln and packing machine and so on. All the necessary equipments in this line can be provided by our factory. We have cement production line experts to design specific solutions for your preference.
MDH20: Transmitting power: 1600--2500 kW, Ratio: 62--65: 1.
Cement rotary kiln. According to your needs.
The cement complete equipment. According to your needs.
Cement opc 42. 5 & clinker Sell cement opc 42. 5 and clinker, pls contact us if you serous to buy! Pearl
Product Name Cement Brick Making Machine Color As Picture Application Buliding Construction Quality High Quality
Summary 1. Cf410s dispersant can significantly reduce cement slurry consistency, improve liquidity and rheolog- Ical behavior of cement slurry 2. Cf410s dispersantis applicable in a wide temperature range and can be resistant to 356°f (180°c). 3. Cf410s dispersant has salt resistence and still has good performance in 5%-10% brine cement slurry. 4. Cf410s dispersant is suitable for dry mixed as well as water mixed, soluble in cold water. 5. Cf410s dispersant is compatible with cement and other additives well. Special attentions The performance of cf410s dispersant will be obviously decreased when dispersant cf410s is used in brine system, whose concentration is higher than that of the half saturated brine. Applications Temperature:lower than 356°f (180°c) (bhct). Dosage: cf410s dispersant generally 0.2-2.0% (bwoc), recommend amount 0.5% (bwoc).
ModelGrinding Table Diameter (mm)Roller Diameter (mm)Roller Number (n)Motor (kw)Output (t/h) GRMK30.313,0001,6003125055~60 GRMK32.313,2001,7003160065~80 GRMK35.413,5001,8004180085~100 GRMK40.414,0001,90042500115~125 GRMK43.414,3002,12043000135~145 GRMK46.414,6002,24043350150~160 GRMK48.414,8002,24043550170~180 GRMK50.415,0002,36043900190~200 GRMK53.415,3002,50044600210~230 GRMK56.615,6002,50065300235~250 Packaging Details:Standard Container Delivery Detail:30 Days
The product obtained by grinding cement clinker obtained by roasting suitable raw material, consisting essentially of anhydrous calcium sulphoaluminate and dicalcium silicate. Suitable gypsum and 0-10% limestone shall be blended with clinker during manufaturer of rapid-hardening sulphoaluminate cement. The rapid-hardening cement product is hydraulicity binding material. It has high early strength. The code no is R-SAC and with four grades.
