Hydrated Lime is a dry powder mainly composed of calcium hydroxide Ca(OH)2. It is a colorless or white powder, which is obtained by hydrating Quicklime (Calcium Oxide) using specific equipment called hydrator in a process called hydration. The process converts CaO to Ca(OH)2. Actually, hydration is a chemical process in which water molecules combine with Quicklime. CaO + H2O â?? Ca(OH)2 + Heat Hydrated Lime has other common names like Slaked Lime, Caustic Lime, Builderâ??s Lime, and Slack Lime. Applications for Hydrated Lime: Water treatment Waste treatment Acid neutralization Building Fertilizer Soil stabilization Asphalt filler Food additive
In different countries, rebar is produced based on different standards, and in each standard, there is a definite classification in relation to the mechanical properties of steel. Most of the steel mills production complies with the Russian standard which is divided into three types of A-1, A-2 and A-3 steel. The A-1 grade is of a flat type. The yield strength and tensile strength (rupture stress) are 2400 and 3600 kg / cm2, respectively. The A-2 grade is of an indented bar type with the yield strength of 3400 and a tensile strength of 5000 kg/cm2. The A-3 grade is also of an indented bar type with a yield tolerance of 4000 and a tensile strength of 6000 kg/cm2. Arij Global Trading, with years of experience in supplying steel products, supplies the best quality of Rebar according to the world standard properties.
Wire Rod is used in the industry in two types of indented and plain with the size of 5.5 mm to 16 mm. Wire Rod is manufactured in the factories up to the size of 12 mm, and the higher sizes are produced according to the order. Also, the indented wire rod is divided into two categories of A2 and A3. Wire Rod is used for different products and is the raw material for the wire drawing units, fasteners, automobile components, and hardware manufacturers. With a successful history of supplying and exporting steel products, we have effectively positioned Arij Global Trading to meet the various requirements of our clients in different countries with the highest standards of quality of Wire Rod.
Ground Granulated Blast Furnace Slag (GGBFS) is a by-product from the manufacture of Iron and a high-performance substitute to traditional cement that will rise the technical presentation of your application, improve its appearance and minimize its environmental impact. GGBS is used in combination with Portland cement to produce superior longer-lasting concrete. GGBS will improve performance in any situation, from housing to civil engineering applications. GGBFS also improves the concrete toughness, reduces preservation and repair costs, progresses workability and compression features, extensions compressive and flexural strengths, decreases cement and water consumption, advances concrete grading and also improves impermeability and water resistance. Arij Global Trading LLC is a professional Ground Granulated Blast Furnace Slag supplier. We are a global company operating in the fields of the mineral industry, trade, and logistics. Reliable and responsible entrepreneurship, combined with flexibility and innovative logistics solution, plus our motivated and skilled employees, our core proficiencies and efficient work processes, we continuously achieve an above-average value contribution. GGBFS Ground Granulated Blast Furnace Slag (GGBFS) is gained by grounding the Granulated Blast Furnace Slag into the desired fineness. This product is usually intended to be used in concrete either as an element of composite cement such as Blast furnace Cement/High Slag Blast Furnace Cement or as a straight addition to the concrete mix by the concrete producer. GBFS Granulated Blast Furnace Slag GBFS can be used like sand as an additional aggregate for building materials. Granulated Blast Furnace Slag is obtained by quickly chilling (quenching) the molten ash from the furnace with the help of water. Throughout this procedure, the slag becomes fragmented and changed into amorphous granules (glass).
This sedimentary rock which is composed primarily of Calcium Carbonate is integrally a multi-functional mineral used in industries for centuries. Limestone as one of the oldest minerals due to its very enduring geological evolution possesses different forms in nature and exhibits different colors. Its properties such as hardness, compactness, imperviousness, and durability have a significant role to play when it comes to its uses which are vast and versatile. This oldest component of ancient landmarks in the world is still practically an inseparable part of industries today. Middle East is amongst the top commodity traders of this mineral. And Arij is honored for having supplied the highest quality of Limestone and specifically the highest purity of 99% at a cost-effective price to different countries. This mineral has enormous diversity of industrial applications and what follows are some key uses of Limestone: Steel industry Construction Materials Refractory Sugar Refining Agriculture Paper manufacturing Glass Manufacturing Leather Tanning Pharmaceutics Food Industry
Calcined Dolomite, Dead-burned or sintered dolomitic refractories, which are prepared by high-temperature calcination dolomitic ores, are extensively used in the steel industry for open-hearth furnaces and repair of the hearth linings of basic electric. Such refractories are also employed in the form of bricks for the working linings of oxygen steel converters which are used with the oxygen conversion process which is becoming broadly popular in steel production.
Gypsum is one of the primary construction materials that has been used for thousands of years that abundantly found in the solid crust of the Earth in relatively thick layers that is extracted from mines and utilized. Calcium Sulfate Dihydrate is a very soft mineral that commonly named Gypsum with the chemical formula of CaSo4.2H2O that its composition contains two water molecules.
LLDPE is used in extrusion, blow molding film, roto-molding, injection molding for food-packaging, frozen food, floor-heating pipes, stretch film, cosmetics, and drugstore, etc. Besides, LLDPE is widely used as a carrier in masterbatch production.
HIPS, high impact polystyrene, is polystyrene, which has butadiene rubber as an impact modifier, giving the material good impact performance but losing the transparency.
When the polystyrene raw material contacts the water vapor, the pentane gas granules within the material are expanded. When these expanded gas granules adhere to each other, Expanded Polystyrene (EPS) is formed. It is used for packaging and heat insulation. The main uses of the expanded polystyrene that is preferred with its wide range of advantages are as follows: * Signboard applications * Electrical equipment * Insulation materials * Lighting fixtures * Food packaging applications * Foam containers * Yogurt containers * TV panels * Stationery products
Because of the bright future of the universal requirement for DRI briquette over the next two decades, a new method was created in 2009 in Iran to produce a cold briquette of CDRI (Patent No. IR60923). Cold-Briquetted Sponge Iron (CBSI) was the name given to the new product. Afterward, following pilot-scale and performing various laboratory studies, Cold-Briquetted Iron and Carbon (CBIC) was invented in Iran as a premium product over CBSI because of the prior�¢??s higher carbon content sand higher efficiency through processes of steelmaking (Patent No. IR84090). Owing to the fact that the cold-briquetting process of DRI is being done under high pressures, the density and mechanical strength of CBIC should be higher and the surface area and also porosity should be less than DRI�¢??s. thus, the oxidation rate, dust and fine generation rate, and the moisture adsorption capacity of DRI will considerably decrease through the process of cold briquetting. These improvements would have big technical, economic and environmental effects on direct reduction and industries steel manufacturing and will push them heading for more sustainability
calcium oxide (CaO), or commonly referred to as quicklime, is a high calcium content derivative of our 98.5% pure calcium carbonate (limestone). Calcium oxide is produced by heating calcium carbonate to 2000 degrees F where carbon dioxide disassociates as a gas from the calcium carbonate: {CaCO3} + Heat = {CaO} + {CO2} Calcium oxide can be utilized in a variety of applications because of its physical and chemical qualities. Arij Global Trading quicklime is used in flue gas desulfurization, water and waste water treatment, steel, paper, chemical and environmental applications.
Although the usage of Bitumen refers to the ancient time and millenniums before BC for excellent adhesive and waterproofing, still, it has a significant impact in modern lives, construction, surfacing airfield runways, taxi tracks, waterproofing, rolling roads and highways. Today the world's demand for Bitumen accounts for more than 100 million tons per year, which is approximately 700 million barrels of Bitumen consumed annually. Applying experience gained in the industry, our highly qualified staff are backing Arij's mission to provide their customers with goods manufactured to the highest standards of Bitumen. We have established long-lasting and close partnerships with manufacturers and refiners from the gulf regions which brings us valuable complements of supplying all types and grades of Bitumen such as Penetration Grade Bitumen (Asphalt), Viscosity Grade (VG) Bitumen, Performance Grade (PG) Bitumen as well as other special types such as Polymer Modified Bitumen (PMB), Bitumen Emulsion (Asphalt), Oxidized Bitumen (Blown Asphalt) and Cutback Bitumen, in any kinds of packages based on customers' requirements
The rapid expansion of high-power EAFs (Electric Arc Furnace) has increased the interest to use DRI as a great option for the continuous charging of electric furnaces in developed countries. Sponge iron is a valuable source of iron for the production of high-quality steel. With the Direct Reduction technology that has been developed considerably in recent years, sponge iron melting in electric arc furnaces has more qualitative advantages than scrap metal smelting for steel making. Some of the benefits include: More specific chemical composition Low levels of impurities (gangue, sulfur, and phosphate) The impossibility of using cheap scrap Easy storage and shipment Continuous automatic charging Predictable price structure Fixed power of input electricity Relying on the knowledge, valuable experience and history, and empowerment of our team, we, Arij Global Trading Co. are supplying our high-quality gas-based DRI to the far destinations in containerized and bulk shipment. As a supplier of gas-based Sponge Iron with a great history and experience, we also provide cost-effective solutions for the shipment to our customers in complete accordance with their needs, which ultimately fulfills the goal of providing satisfying service.
HBI is the preferred DRI product for the merchant metallic market; Because it is much denser than CDRI, which reduces the re-oxidation rate. In fact this enables HBI to be stored and transported without special precautions under the International Maritime Organization (IMO) code for shipping solid bulk cargoes. Besides we can use it the EAF, BF, and BOF. Consequently, HBI which is the product of compressing DRI discharged from the MIDRE Shaft Furnace at 650 C into pillow-shaped briquettes; with a typical size of 30 x 50 x 110 mm and a density 5 gm/cc. No binder is used to make HBI.
HDPE is widely used to produce pressure pipes, gas distribution pipes, bottles, drums, barrels, white goods, and machine parts, insulators, toys, electrical and electronic goods. Grades: The most important commercial grades of HDPE polyethylene materials are EX5 / HI500 / EX3 / BL3 / PE100 and 6040. Here at Arij global trading, we have established long-lasting and close partnerships with manufacturers and petrochemical companies from the area, which brings us valuable complements of supplying all grades of HDPE. We are able to provide any considerable quantity of various grades of HDPE in granule or powder form. The granules or powders can be shipped using jumbo bags or smaller packages, based on our dear customers' requirements.
LDPE, which is generally colorless, translucent, flexible, odorless, tasteless plastic, is one of the most excellent properties of heat sealability and can be adhered at about 120 C. Because of this feature, it is widely used as an intermediate layer to connect two layers which do not stick to each other thermally in the coatings. It also has favorable properties such as being transparent and resistant to tearing, significantly reducing water vapor permeability, and significantly reducing its elasticity at low levels.
GPPS, general-purpose polystyrene or crystal-clear polystyrene, is fully transparent yet brittle, a CD case, and is widely used in food packaging applications or jewel cases.
Fertilizers, Urea, Granular, solid nitrogenous fertilizers Urea is a nitrogen-containing chemical product that is produced in excess of 140,000,000 tons per year worldwide, of which more than 90% of world production is destined for use as a fertilizer and is an important raw material for the chemical industry. Urea can be produced as prills, granules, flakes, pellets, crystals, and solutions. We, Arij Global Trading, provide our customers peacefulness by our ability to fast adaption and answer to their requisitions and provide a secure supply of Urea Fertilizer by our safe, reliable and cost-effective operations.
This alcohol is also known as Methyl Alcohol or MeOH, primarily from natural gas. It finds major application from clothing to fuel, as a precursor for other chemicals, such as formaldehyde, acetic acid, and MTBE (octane booster in gasoline). It can also be applied as a denaturant for ethanol and solvent. Supplying from various large governmental manufacturing companies having the state-of-art facilities, We, as Arij Global Trading, are the leading and a main supplier and exporter of Methanol with high quality and very much competitive price.
