Electronic specifications Total harmonic distortion 0.0015% Frequency response +/-0.5db from 4hz to 20, 000hz +0.5/-3db from 4hz to 68, 000hz (source dependent) Maximum volts out (balanced / unbalanced) 16/8 v rms Input impedance (balanced / unbalanced) N/a Phono voltage gain N/a High level voltage gain N/a Signal to noise ratio 110db Dual mono power supply No Dual mono, fully balanced Digital, fully balanced Connectivity Balanced inputs 0 Unbalanced inputs 0 Phono moving coil input 0 Phono moving magnet input 0 Digital coaxial input 2 Digital optical input 2 Digital mct (din) input 1 Digital usb input 1 (2.0, 32/192 asynchronous) 44.1khz to 384khz, 32-bit (pcm) dsd64, dsd128, dxd352.8khz, dxd384khz Digital aes/ebu input 0 Balanced fixed outputs 1 stereo Balanced variable outputs 1 stereo Unbalanced fixed outputs 1 stereo Unbalanced variable outputs 1 stereo Headphone output 1/4â?³ high drive Record processor loop No Input level match No Home theater pass through No Control Tone controls No Tone bypass and input assign No Rs232 control input No Power control output 1 Rear panel data ports 1 Rear panel ir sensor input Yes General specifications Multi-chassis or single Single Output meters No Tube or solid state Solid state On, power consumption 30 watts Weights & dimensions Dimensions (w x h x d) 17.5â?³ (44.45cm) x 3-7/8â?³ (9.8cm) x 16â?³ (40.64cm) Weight 13.5 lbs (6.1kg) Shipping weight 28 lbs (12.7kg)
A Valve Pre-Amplifier to meet the highest standards. Inside, the 4x12AX7 and 3x12AU7 valves provide the perfect pre-amplification for weak signals. The circuitry with its negative feedback design is the optimum of linearity and sound. Gold-plated high-grade Neutrik XLR input and output connectors take the relevant cables, giving the best possible quality, and they guarantee a clean sound. Frequency response: 20 Hz 50 kHz +/- 0.5 dB, Output voltage: 2V Total harmonic distortion: < 0.1 % (1 kHz, 1 Watt) Input sensitivity: 240mV, Signal-Noise ratio: > 90 dB Input impedance: 47 kOhm, Inputs (golden): 4 x RCA, 2 x XLR NEUTRIK Outputs (golden): 2 x RCA, 1 x RCA Rec Out, 1 x XLR NEUTRIK Power Control Switched output voltage: 2 x Trigger 12 V (Output) Mains supply: 230 V/50 Hz, Weight: 10 kg Dimensions (WxHxD): 430 x 135 x 370 mm, Colour: black/silver Tubes: 4 x 12AX7, 3 x 12AU7, double transformer A valve Pre-Amplifier to meet the highest standards. Inside, the 4x12AX7 and 3x12AU7 valves provide the perfect pre-amplification for weak signals. The circuitry with its negative feedback design is the optimum of linearity and sound. Gold-plated high-grade Neutrik XLR input and output connectors take the relevant cables, giving the best possible quality, and they guarantee a clean sound.
Product Application By the advanced impact extrusion technology, we can manufacture the products such as aluminum bottle, aluminum cover, aerosol can, collapsible tube.,etc These Products are widely used in cosmetics packaging, electronics, medical, food and automotive industries Product Features: a.Customized in Shape and Size at your choice; b.Good flexibility and tractility, corrosion proof well, and attractive appearance; c.Excellent Quality In accordance with European Standard EN570/573. Product Range: a.Product Specifications: Alloy Purity Hardness Thickness Diameter Tolerance 1070 99.70% 16-20 HB 2-30mm 6-140mm �±0.05mm Annealing temper is:450 to 480 centigrade, time is: 8 to 12 hours b. Chemical composition (%): Alloy Si Fe Cu Mn Mg Cr Ni Zn Ca V Ti 1070 0.25 0.25 0.04 0.03 0.03 - - 0.04 - 0.05 0.03 Other Min Al 0.03 99.7 Product Shape: Shape: Round, Oval, Column, Rectangle Domed , Conical Surface Technology Tumbling or Shot-Blasting Product Process: 1-1070 Aluminum ingot-Smelting This stage starts by loading furnaces F1th ,F2th with 30MT each of raw aluminum (alloy AA1070, purity 99,7% 2-Continuous casting and hot-cold rolling The melt is poured into the strip casting wheel, which rotates at a speed of 6 meters/min. A strip of 220 mm wide by 20 mm thick is formed. 3-Cold Lamination/Rolling which aloud a maximum tolerance 0,05 mm 4-Stamping/Punching This stage counts with four stamping presses, In this process we get about 50% of slugs for each Ton of punched strip. 5-Annealing Treatment With this we obtain a Brinell hardness of 16 a 21 HB. 6-Surface Finish Surface treatment is sand blasted, vibrated and tumbled 7-Final Inspection QC department(gauge,mechenical test, surface quality) 8-Selection and Packing Boxes are marked with customers information QC -Testing The quality policy of Nansen Industries is to establish implement and maintain an effective assurance system. Based on standard of EN570 and ISO 9001 with the full employees in the process of continuous quality improvement and quality assurance practices resulting in our customer satisfaction. The purpose of our quality system is to continuously improve the quality of our products, our services and productivity in order to achieve internal and external customer satisfaction.
Scrap tires, waste tires, scrap tyre, waste tyre.
Tyre Scraps..
