The main description of the plant equipmet is: 1. Brew House Make & Capacity: Steinecker1995 -1999 5 brews/d, 450-500 hl/brew. for 7000 kg malt, 3850 Raw grain Cast-out quantity: 500 hl, 16,5° Plato 8 Brews/ 24 hours, annual capacity 0.85 Mhl Controls are based on Siemens S5 and S7 PCS with, Botec Control system, PC Windows 2000 (Steinecker) Laboratory yield = 97.1% (2.1.09 – 28.5.09, 837 brews) The Brewhouse was installed in 1996 - 1999 by Steinecker to a high standard of control and automation and it contains the following main equipment: Wet Conditioning Mill, capacity 20 tons/hour and it is fully overhauled 2008 Configuration, main characteristics: 1 wet mill plant: 20 t/h 1 mash tun kettle plant: V=550 hl 1 lauter tun plant: D=7200mm 1 weak wort tank: V=155 hl 1 pre run vessel: V=640 hl 1 CIP- water distributor brew/whirpool kettle hot wort max. 520 hl (1 brew / 5 hours) wort cooling 400 hl/h, 10°C - Mash Kettle, a jacketed vessel 550 hl - Enzyme Dosing pot and pump - Lauter Tun complete with spent grain tank and Pondorff pneumatic grains transfer. Tun capacity 814 Hl and diameter 7200 mm, Solids capacity of 7000 kg malt and 3850 kg raw grain. Complete with internal rakes and scrapers - Pre Run Vessel complete with internal heater , volume 640 hl - Wort Boiler/ Whirlpool, gross volume 757 hl net 520 hl - Wort Cooler with aeration – GEA supplied plate heat exchanger (YOM 1990) – rated at 450 Hl/hr cooling the wort from 95oC down to less than 10oC. Cooling achieved with brewing water and then chilled water. Aeration achieved by use of a sintered disc and static mixers, and controlled manually using mass flow meters - 2 Hop Pellet Tanks - 2 Hop Oil Tanks - Brewhouse Weak Wort Tank, volume 150 hl - Alfa-Laval Decanter, year 2008, capacity 100 hl / h - 2 Weak Wort Tanks, volume approx 80 hl each - Gypsum Tank, volume approx 40 hl - Wet starch tank – volume 100 hl - Spent Grains Silo - Spent Grains Drying System - Bulk Acid tank – plastic tank with integral bund and dosing pumps
The fan is made by German Pollrich Ventilatoren GmbH in year 2004 and it has been as a back-up emergency fan which has practically newer used and therefore the unit is new like condition. This fan was designed to blow explosive air/gas mixture (VOC) and therefore it fulfills category II 2G, temperature class 1 ATEX 95 norm of explosive proof design. The motor and fan are built on a common heavy duty frame and they are connected with a flexible coupling. Technical data: Manufacturer: Pollrich Ventilatoren GmbH Year of manufacture: 2004 Fan type: VR50S11C1UK0900LG360MMUU Manufacturing no: 123665 Volume: 10.55 m3/sec (37980 m3/h) Max press difference: 8000 Pa (0.08 Bar) Speed: 2980 RPM Max gas temperature: 80 C Power requirement: 104.6 kW Electric motor: CEMP 132 kW / 2970 RPM Type: AC70 315M 2 Classifications: II 2 G EEXd IIC T4 IP 55.
This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit. This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate. Machine type:Powerpak 660 Machine number:665/0211 Manufacturing year:1998 Foil type:Flexible Formatting width:430 mm Film type used:PS-PE 450/50 Max formatting depth:40 mm Forming dies:223-3,1 Capacity:10 phases / min Control unit:Tiromat Ho foil printer:SC-700 with 3 printing units Overall length:7.30 meters Overall width:1.15 meters Height:1.85 meters Nominal power need:50 A / 380 V / 50 Hz.
The boiler is a three-pass, fire-tube steam boiler made by Finnish Ahlström Themoflow in year 1990. The boiler has max operating pressure16 bar with 205 C steam temperature and it is equipped with exhaust gas economizer for preheating incoming feed-water and modulating heavy fuel oil burner. It's has a large 15.2 m3 water volume which allows big momentary changes in load. Other benefits include simple structure, long operating life, reliability and ease of service and maintenance. The boiler is in good operational condition. Feed water pumps and feed water tank with aerator are available for separate request and price. Technical Data: Manufacturer: Ahlström Thermoflow, Kaarina Manufacturing year: 1990 Capacity: 3.3 MW Water volume: 15.2 m3 Steam characteristics: Max 16 bar, at 205 C temperature, saturated Oil Burner: Weishaupt Monarch RMS 50/2 A - ZM (YOC 1990) Oil feeding: 140 - 490 kg/h.
Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets. More information on requests, for spam protection please introduce yourself properly. Main data of one mill: Manufacture’s type: NTK 130F/LM Year of manufacture 1988 Total operating hours: approx. 75000 Rated capacity, max: 145 kW Number of blades: 3 pcs Rotor diameter: 22 m Rotor speed: 44.5 rpm Cut-in wind speed: 4.0 m/sec Cut-out wind speed: 53 m/sec (120 mph) Hub height: 26 m Generator: ASEA 145 kW / 1500 rpm / 50 Hz Blade type: LM 9.7 m H/H/T diam. 21 m Gear box type: Lohman & Stolterfort GPC 145 Clutch type: Lohr & Brokamp Universal Joint No 105 Total weight: 15200 kg.
Good condition GEA Westfalia centrifugal separator used for molasses removal from fermented beer. The equipment has patented HydroStop solid discharged system that can be adjusted precisely and reproducibly to the specific solids concentration requirements of the process. This beer separator has continuous and self cleaning separation process and in beer filtration application this separator eliminates the need to use kieselghur. Technical information: Manufacturer: - GEA Westfalia Germany Year of manufacturing: - 2002 Manufacturer's type: - SC 30-06-177 Capacity: - 4000 - 6000 liters / hour Electric drive: - 18.5 kW Bowl diameter: - 440 mm Bowl speed: - 7270 rpm Relative density of solids removed: min 1.4 kg/l Relative density of suspension: max 1.2 kg/l Particle size or removed solids: > 4.6 micron Centrifugable solids: - max 5% v/v Viscosity of free liquid: - 2.5 - 5.5
e equipment was manufactured by Jeffrey Rader AB, Sweden in 1995 and it is in very good operational condition. It consist of two heavy duty rolls with removable profilied surfaces which rotate towards each other and presses overzised wood chips between the profiles. Roll drives 2 x 110 kW / 1500 rpm connected with two gearboxes. Hydraulic pump 7.5 kW, capacity 220 m3/h wood chips. The equipment was manufactured by Jeffrey Rader Inc, Sweden in year 1995, manufacturers type is DynaYield 80-300 and it is in good operational condition. The Chip Conditioner consists of two heavy duty rolls with removable profiled surfaces. They rotate towards each other and pull the oversize chips between them. The profiled surfaces are aligned so that the pyramid apexes on one roll travel in the valleys of the apexes on the adjacent roll. With normal oversize wood, the Conditioner typically generates less than 1% fines and 3% pins The normal application for the Chip Conditioner is in a chemical pulping process, processing the oversize materials by fissuring the wood chips parallel with the grain to allow the cooking liquors to penetrate the chip, and allow the oversize chip to cook as an acceptable size chip. Another application is in a thermo-mechanical pulping process (TMP), as a preconditioning An important feature of this machine is its ability to handle small portions of tramp without going off-line. With the so called Dynagage Conditioner, the dynamic roll is allowed to move away from the static roll, and once the tramp is through the unit, the roll automatically moves back to the proper set point without shutting down the flow and together with slow rotation speed enable were low down time and maintenance costs. Roll distance movements are made with a hydraulic system build on the equipment and controlled by 3 position sensors More information on requests, for spam protection please introduce yourself properly. Technical data: Model: RDY 80-300 Manufacturing year: 1995 Capacity (throughput): 220 m3/h loose wood chips Press roll diameter: 915 mm Roll length: 2440 mm Roll motors: 2 x 110 kW / 1500 rpm / 690 V – 50Hz Press distance between the rolls: 2.2 mm Gearboxes: 2 x Kipo Benzler TV 512 Hydraulic pump: Rexroth 200 bar with Mecman syliders Electric motor for hydraulic pump: ASEA 7.5 kW Weight: 33 000 kg Length: 5083 mm Width: 2550 mm Height: 2400 mm.
Krones Toptronic K 719-555 Rotary Empty Bottle Inspector The Toptronic inspector is made for inspecting empty returnable PET bottles and empty non-returnable and returnable glass bottles. It utilizes state-of-the-art camera technology to provide precision empty container inspection. The sophisticated inspection modules detect even the tiniest damage or contamination – both in glass and PET returnable bottles. General design features Modular design Table top cover and stand cladding in stainless steel Safe bottle guidance with Raptec handling parts Blower for removing foam and lubricant residues from the container base Enclosed and air-conditioned electronics cabinet Electronic function monitoring Stop function upstream of machine infeed in response to fallen-over containers Rejection unit with retaining bar or clamping starwheel This unit has been in operation only with PET bottles sizes 0.5 liter (four different types), 1.5 liter ( two different types) 1.0 and 1.25 liter bottles and it has been in operation since 2002 and is still in very good operational condition. Handling tools for above mentioned PET bottles will be a part of delivery. Technical specification: Manufactured by: Krones AG, Germany Manufactured in: 2002 Model: K 719-555 Nominal output: up to 72000 bph Actual output: 35000 bph (with clamping starwheel) Inspection units (PET) For foreign containers P.E sensor and camera Base 1 Camera Variostation 1 Camera - sealing surface Residual liquid High frequency + infrared Side wall Camera Optimized scuffing Camera Variostation 2 Camera - Base 2 - inner side wall - full thread Variostation 3 Camera - full thread - lateral neck finish - inner side wall Variostation 4 Camera - sealing surface - lateral neck finish Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Wood Working.
Yogurt production and packaging line 4000 l / shift 0732010 Yogurt production and packaging line 4000 l / shift Yogurt production equipment consists of 4 pcs 1000 liters of yogurt fermentation tanks, transmission equipment and a fully automated filling line 150 - 200 grams plastic cups. Process operation requires two people and equipment can be made about 4000 liters (or 20000 pieses) of 200g canned yogurt cups or other similar product for a normal 8-hour working shift. Packaging equipment is manufactured in the 1980s by German Ganzhorn & Stirm (nowadays Casti) and an automatic product cup feeder has been added later on the line. Also the tray feeding device has been recently added. The production line is fully operational and suitable besides for yogurt production, also for all curdled / fermented milk packaging in 150g-200g cups. Fermentation tanks are double walled 1000 liter stainless steel vertical tanks. The product temperature can be adjusted as desired (e.g.36C) by using heating water between double walls. Control valves are manually adjusted. The fermented yogurt is transferred to two 100 liter feeding tanks of the packing line with gentle rotary lobe pumps. Filling the yogurt cups is fully automated 2-lane packing process. The main equipment are manufactures by German Canzhorn & Srimin. Later installed automatic cup feeding equipment places 150 gr - 200 gr cups in 2 rows on the filling machine. The filling machine fills cups in three phases; first to the bottom desired volume of jam and then two different layers of product mass. ( 3-layer of yogurt). The cups are closed with aluminum lids which is sealed with electric heater. Transfer conveyor moves closed cups on to a palletizing machine which loads 20 cups on each cardboard or plastic tray (tray is automatically fed by a tray feeding device) where full trays are moved to a stacker machine which piles several layers of trays (up to 1 meter tall) for transportation. Technical Specifications: The manufacturer: Ganzhorn & Stirm (Casti) Filling machine type: DOGatherm 61 Stacker type: BE 75/2 Production capacity: up to 4000 liters / shift Yogurt fermentation tanks: 4 x 1000 liters Cups & filling: 150 - 200 g / max. 3-layer filling Filling line length: about 12 meters.
Stainless Steel Tank 3.5 m3, with variator driven mixer 3pcs excellent condition vertical stainless steel (food quality) tanks with electric motor driven and mechanical variotor speed controlled heavy duty two plade mixer. The tanks are made by Finnish Tankki Oy in 1992, they have are standing on 3 heavy legs, liguid volume 3.5 m3, conical bottom for easy discharge. Necessary service man door and other connections for venting, filling and discharging. Total height: 3.4 m (+ motor and connections 50 cm) Diameter of the tank: 1.6 m Wall height: 1.8 Mixer: Sew-Eurodrive KAF76-D34 Mixer rpm: 12.2 - 60 rpm Moment: 900 - 400 Nm Electric motor 3.0 kW / 1400 rpm.
Drum and Container Filling Line, Semiautomatic YOC 2006 The line is designed for filling both 1000 liter IBC’s and normal 209 liter drums / barrels. It consist of straight chain driven heavy duty roller conveyor which is carrying IBC’s or a standard pallet loaded with four drums / barrels through the filling process and conveying them for further storing. The filling machine is semiautomatic coarse-and-fine filling station; first is programmable volumetric and then fine filling with integrated weighing system. Cap closing / bunging and sealing will be made manually but a machine aided. The station operation is controlled by Siemens S7C programmable logic. The line is manufactured in 2006 by Finnish company “Insinööritoimisto Jyrki Kekälainen” who is specialized supplying automation solutions filling and packing applications. Operation description: The operator lifts the empty containers on the conveyor (open the cap of container), the container will move into filling machine and it will be filled automatically with 2 "and 1 / 2" valves, coarse-and fine-filling. After filling the container will move out of the machine and the operator will fix the label and close the cap. After the filling station there is ~16 m long puffer conveyor for the filled IBC`s, where a fork lift will pick up the IBC`s In drum filling the operator lifts the empty drums on pallet (open the caps). Then he lifts the pallet on the conveyor. In the machine there is an extra filling lence for the drums. The drums are filled on the weighing system of the machine which is controlling the filling of each barrel. After the drum is filled the operator move the lence into second drum and machine start to fill it. After all drums are filled the pallet will move out of machine and the operator will close the caps and fix the seals and labels. Technical data: Manufactured in: 2006 Suitable for: Standard IBC and Drums Max filling weigh: 1500 kg Filling accuracy: 0.5 kg Filling capacity: 7 IBC/hour or 35 Drums (209 liters) / hour Roller conveyor type: Chain Driven, Galvanized Roller conveyor length: Approx 16 meters Roll diameter: 80 mm.
GEA Varitherm VT-20 Plate Heat exchanger is made of several Varitherm-design stainless steel plates which are combined to form one effective heat transfer unit. Within each plate package the heat exchanger plates support each other at the metal-on-metal profile cross points, which ensure the stable behavior of the plate gap. The plate gasket has so called glue less sealing system. VT-20 is specially designed for cooling and heating of fluids with particle content up to a particle size of 2 mm as well as condensation of vapors, gas cooling and gas dehumidifying. This unit is in good operational condition. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width: 337 mm Length: 999 mm. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width (plates) 337 mm Length (plates): 1370 mm.
Very little operated (ony 6000 hours totally!) fuel oil fired package boiler made by Högfors (nowadays Foster Wheeler) in 1988. Complete plant with combustion air fan and feed water pumps for immediate delivery, in very good condition. Main scope of the delivery: - Högfors 30 t/h boiler - Oilon burner - Economizer - Combustion air fan - 2 pcs of 90 kW / 25 bar KSB feed water pumps - Fuel oil pumping unit made by Oilon - 8 pcs of steam shoot blowers - valves, fittings and maintenance supports . Type of boiler Water tube type with natural circulation, with two drums Manufacturer Kymin Osakeyhtiö, Högfors, Finland (Foster Wheeler) Model of the boiler: H52-47-25 bar Year of manufacturing 1980 Starting day of operation 16.11.1980 Evaporation 47 t/h saturated steam Temperature of steam 226 oC Effect 30 MW Structural pressure 25 bar Feed water temperature 120 oC Furnace volume 74,5 m3 Surface of furnace c. 136 m2 Surface of convection part 420 m2 Surface of economizer c. 504 m2 Water volume 15,8 m3 Oil Heavy oil (POR 230) Oil burner Saacke SKV, fully automatic, modulating Regulating area of burner 610-3050 kg/h Oil pumping- and pre- Oilon Osva 4000 kg/h heating station Feed water pumps 2 pcs + 1 pc as spare. KSB-centrifugal pump MOVI 65/6, massflow 59 t/h, 29,5 bar motor 90 kW, 2900 r/min Primary air fan Mercantile KDER 75, 37300 Nm3/h, motor 115 kW, 1500 r/min Sootblowers Diamond Superior sootblowers 4 pcs in boiler part Diamond Superior sootblowers 4 pcs in economizer. Dimensions of boiler part: Height 5,2 m, Width c. 4,5 m, Length 10,0 m Weight of boiler part c. 54 t. without water and accessories Weight of economizer c. 15 t. without water and accessories Boiler is suitable for gas operation by changing the burner. The boiler has been in operation only about 6.000 hours. Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Gas & HFO Boilers Wind Turbines.
Double floor tool storage made of removable metal structure. Walls on 3 sides of the storage, one side is main building wall. Includes two lockable separate storage rooms and selves. Free height in lower level is 2.7 meters. Material is steel and aluminum. Will be sold as is where is bases.
Plasmatreat FG1002 pre-treatment and cleaning unit This flat surface pre-treatment and cleaning unit with open air / atmospheric-pressure plasma technology was originally made by Plasmatreat company in 2004, manufacturer's model FG1002 with Siemens PLC control system and then in year 2008 it was refurbished with new plasma nozzle directing robot and an aluminium profile structured operation table. The unit has two plasma nozzles and it has been used on occasionally and is in excellent condition. The equipment has CE marking and proper documentation, including wirering diagrams This machine is designed to pre-treat and clean any metal, aluminum, plastics (such as PP and EPDM) or glass surface free from grease, dust and other unwanted materials and to pre-treat material surface for ensuring the adhesion of surface coating to these materials. Plasmatreat process also allows to use environmentally friendly water-based painting for coating and due to the fact that cleaning with plasma is a dry process immediate further processing of the materials is possible. For more information, please visit manufacturer's web page www.plasmatreat.de Technical information: Manufacturer:Plasmatreat Company Model:Plasmatreat Openair® FG 1002 Serial number:695 Year of manufacturing:2004 / 2008 Operation table size:1600 x 3000 mm Electricity connection:3~/ 400V / 32 A Condition:Used, excellent.
Bedroom furniture Two person bed Size 3-3m.30kg.
Grades: select, nature, rustical, vintage Mainly oak, but also other species possible Olso xl, xxl and solid parquets Pallet = 100 m2, 750 kg, 2, 2 x 1, 0 x 0, 7 m Plastic foil cover, sea freight package
Deliveries in containers cif major harbor in china French oak
Certificate of quality Fineness % +-10.0 Initial setting time h:min +-0:45 Final setting time h:min +-10:00 Soundness Mum +-5.0 So3 % +-3.5 Mgo % +-5.0 Loss on ignition % +-5.0 Bending strength mpa +-6.5 Compressive strength mpa +-42.5 1ton/big bag
Wooden furniture, library furniture, hotel furniture, school furniture, museum furniture, hospital furniture.
