Compressor single stage, standard speed oil-injected rotary screw compressor with manufactured by German company Drucklufttechnik GmbH in year 2002. The complete unit consists of intermediate pressure vessel and Ultratroc - air dryer all delivered same time as the compressor. The unit is controlled by modern DELCOS 3000 control unit. The total unit has 30320 operating hours, the unit has been regularly serviced by a compressor service company and is in good operational condition. The compressor is single-stage, double screw, V-belt driven electric motor drive compressor which has oil cooler and thermostat controlled water - air after cooler on discharge of the pressurized air. The operations were stopped in year 2006 but the compressor and other equipment are still installed and ready for test run. Technical data: Compressor type:CompAir L90 7,5A Capacity:16.1 m3/min, 7.5 bar Comp. electric motor:90 kW - 400/415 V û 50 Hz Air cooler electric motor:3.0 kW - 400/415 V û 50 Hz Compressor weight:2380 kg Compressor dimensions:2.4 x 1.4 x 2.0 m (W x L x H) Air dryer type:Ultratroc SD 1350 û type 422 Air dryer air volume:22.5 m3/min Total power requirement of dryer:2.4 kW DryerÆs refrigerant:Type R134 a û filling 3.5 kg DryerÆs dimensions:1200x900x800 mm, weight 185 kg Int. mediate air pressure vessel:Volume 2 m3, 10 bar, made by Galvanoimis Oy.
Stainless Steel Tank 3.5 m3, with variator driven mixer 3pcs excellent condition vertical stainless steel (food quality) tanks with electric motor driven and mechanical variotor speed controlled heavy duty two plade mixer. The tanks are made by Finnish Tankki Oy in 1992, they have are standing on 3 heavy legs, liguid volume 3.5 m3, conical bottom for easy discharge. Necessary service man door and other connections for venting, filling and discharging. Total height: 3.4 m (+ motor and connections 50 cm) Diameter of the tank: 1.6 m Wall height: 1.8 Mixer: Sew-Eurodrive KAF76-D34 Mixer rpm: 12.2 - 60 rpm Moment: 900 - 400 Nm Electric motor 3.0 kW / 1400 rpm.
Manufacturer pompetravaini italy, made in year 2002. Vacuum pump is two staged rotating pump with externally located, grease lubricated bearings. Pump is liquid ring type designed for water sealed operation. The impeller and shaft are made of stainless steel (aisi 316), cast iron casing and manifold normal steel. The shaft is sealed with double mechanical seal. Pump is provided with connections for service water and draining. Pump includes also anticavitation valve. Pump is dismantled from its base frame but the delivery includes original electric motor eex classified abb hyr 200m lb 4 30 kw, 1476 rpm, year 1995. The equipment will be supplied loose - not as a skid. Technical data:trch 80 - 540/c2/ra Max suction pressure:25 mbar (till 300mbar) Max capacity:540 m3/h (min 400 m3/h) Flanges:80 mm Rotation speed:1500 rpm Power requirement:30 kw at 1500 rpm Year made:2002 Condition:fully operational
This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit. This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate. Machine type:Powerpak 660 Machine number:665/0211 Manufacturing year:1998 Foil type:Flexible Formatting width:430 mm Film type used:PS-PE 450/50 Max formatting depth:40 mm Forming dies:223-3,1 Capacity:10 phases / min Control unit:Tiromat Ho foil printer:SC-700 with 3 printing units Overall length:7.30 meters Overall width:1.15 meters Height:1.85 meters Nominal power need:50 A / 380 V / 50 Hz.
The boiler is a three-pass, fire-tube steam boiler made by Finnish Ahlström Themoflow in year 1990. The boiler has max operating pressure16 bar with 205 C steam temperature and it is equipped with exhaust gas economizer for preheating incoming feed-water and modulating heavy fuel oil burner. It's has a large 15.2 m3 water volume which allows big momentary changes in load. Other benefits include simple structure, long operating life, reliability and ease of service and maintenance. The boiler is in good operational condition. Feed water pumps and feed water tank with aerator are available for separate request and price. Technical Data: Manufacturer: Ahlström Thermoflow, Kaarina Manufacturing year: 1990 Capacity: 3.3 MW Water volume: 15.2 m3 Steam characteristics: Max 16 bar, at 205 C temperature, saturated Oil Burner: Weishaupt Monarch RMS 50/2 A - ZM (YOC 1990) Oil feeding: 140 - 490 kg/h.
ating line is delivered by Finnish Elmont Oy and it consist of 59 separate dipping tanks, 6 material handling cranes and related process and automation equipment. We have the dipping tanks and material handling cranes in our store for sale. Dipping tank materials are AISI 316, SS, PP, HST and PP. All tanks are 2200 mm long and 1250 mm height, widths varies from 450 to 1740 mm, volumes from 1213 to 4016 liters. All tanks are in good condition. The cranes are designed for those tanks and we have 6 pcs of them. Cranes have 0.25 kW gear motors and control panels. Structure is made of steel and they are in good condition. If you are looking for such equipment, please contact us and we are pleased to give you more deep information.
Kills 99.9% of all known germs instantly, no water required, quick drying Provides rapid anti-microbial kill of a wide-range of micro-organisms A superior alternative to hand-soap, as proven by medical research Specially formulated with Aloe Vera ensuring hands are refreshed and moisturized Tested in accordance with British and European Standards BSEN1040:2005 Medical Grade Antiseptic Disinfectant Hand Sanitizer
The equipment is designed and manufactured by Gough & Co Ldt, UK in year 1999 / installed in 2000, manufacturer’s type single deck Vibracon GVF4. We have totally 3 identical units which were dismantled in 2007 and all of them are in very good operational condition. These are single deck circular screen design for high velocity scalping, de-watering or single deck separation in chemical and pharmaceutical industry. (These units were screening oversized particles in PVC - granulate factory truck loading station) The perforated screen and all product touching parts are made on stainless steel AISI 304L. Top deck houses the screen and the discharge spout for oversize particle removal is fitted to it. Top deck is supported with mechanical spring and vibration movement is created by two contra rotating vibrating motors on the outside of the unit so there are no internal working parts. Vibration power can be adjusted. Technical data: Type: Vibracon GVF 4 Material: AISI 304L – product touching parts Perforated screen: Mesh size 4 mm Screen diameter: 1100 mm Screen area: 9500 cm2 Vibrators: 2 x 0.52 kW units.
Modem External basic ADSL modem for single computers. Connection to PC is USB. ull rate speed support up to 8MBps The modems are ANNEX A type and there is support for major protocols: G.DMT, T1.413, PPPoA, PPPoE, T1.483 Issue 2 G.992.1, G992.2. 9x/Me/NT/2000/XP. Qty: 7000 pcs in-stock Brand new, bulk packed (20 in box) Warranty 1 year Price $7 each , or make offer to take all FOB Helsinki , Finland Bulk, 20 pcs in a box
Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets. More information on requests, for spam protection please introduce yourself properly. Main data of one mill: Manufacture’s type: NTK 130F/LM Year of manufacture 1988 Total operating hours: approx. 75000 Rated capacity, max: 145 kW Number of blades: 3 pcs Rotor diameter: 22 m Rotor speed: 44.5 rpm Cut-in wind speed: 4.0 m/sec Cut-out wind speed: 53 m/sec (120 mph) Hub height: 26 m Generator: ASEA 145 kW / 1500 rpm / 50 Hz Blade type: LM 9.7 m H/H/T diam. 21 m Gear box type: Lohman & Stolterfort GPC 145 Clutch type: Lohr & Brokamp Universal Joint No 105 Total weight: 15200 kg.
The vacuum evaporator is made by Italian Ecoteck in year 2003 and operation was stopped in early 2009 and it is in very good operational condition. This unit is made for concentrate acidic liquid wastes and therefore all liquid touching parts are made of acid proof steel ( SS 2353) or PVC. The evaporation capacity of the unit is 5000 liters / day. The unit is a complete working unit and it includes evaporator, boiler, heat pump, centrifugal pump, water-air cooler, steam ejector, control unit and all other necessary equipment to complete the unit. Operation principle: Steam rises from the boiler through a drop dispenser to the cooling unit where it condensates. The condensate drops with the gravity down to vacuum system. In-build heat pump heats up the cooling media and simultaneously cools down the condensate. Water – air cooler cools down the extra heat from the process. Necessary vacuum is generated with a centrifugal pump and a steam ejector. Condensate rejection takes place in accordance with prescheduled frequency. Technical data: Manufacturer: ECOTECH Srl Italy / Vilokan Ren Miljöteknik Sweden Type: ECO 5000 VS-HP, R407C Year made: 2003 Evaporation capacity: 5000 liters / 24 hour (pure water) Electricity consump.: about 0,15 kWh / liter pure wateri) Control unit: Siemens Micromaster 420 Compressor: Bitzer Kuhlmachinenbau GmbH, Compressor type: 6G-40,2 Compressor capacity: 126.8 m3/h, 19/28 bar Refrigenerant: R 407 C Main dimensions: 2.8 m x 1.3 m x 2.9 m Weight: 1500 kg.
The line is designed to fill beer in to three different type of 0,33 litre glass bottles, label the bottles neck around and lower body small around and pack the bottles in to 4 x 6 bottle cartoon boxes. This bottling line capacity is 20000 bph. Clean glass bottles were brought on wooden pallets to depalletizer which feed them to the filling lines. Innofill DMG bottle filling machine and Handtmann MMS filtration system are located in a clean air room. KHS lamella conveyor system for bottle transport and cartoon boxes. The equipment were totally delivered by German KHS in year 2003, most of machines manufactured in year 2002. All control units are Siemens Simatic S7 model with remote connection. The line was shut down in year 2008 and it is still installed and in very good operational condition. Main equipment are: - Bottle Depalletizer KHS AL, semiautomatic - Micro Filtration Handtmann MMS 130 - Filling Equipment KHS Innofill DMG (rinsing, filling and capping) - Labelling Machine KHS Innoket 2060 - Cartoon Box Forming Machine KHS Innopak CA-1 - Bottle Packing Robot KHS Innopak SP 1200 - Box Marking System - Case Sealer KHS Innopak CV.
This laminating tunnel / convection oven is made by Swedish TRIAB / Tri Innovations AB in year 2006. The oven is designed for industrial use and in build up in two separable laminating sections, both equipped with one 40.5 kW hot air sections, one product and one return conveyors and common control unit. All product touching parts are made either of stainless steel (structures and panels) or Teflon made net belts. Convection belt (600 mm wide) is located inside of the oven tunnel and has grid type surface, the return conveyor is installed on the tunnel and it has tight waived Teflon belt. The control cabinet is attached to the equipment structures. The speed of laminating conveyor is adjusted with an inverter driven motor. The speed of return conveyor can be fine tuned via a potentiometer. The equipment is featured with a remote control possibility. This has been operating with hygienic products (material foam / polyurethane film, thickness 5 mm, max. width 450 mm and production speed 6 m/min) and is in excellent operational condition with total 3450 operating hours only and it comes with original operation manual in English language. Technical data: Made by: TRIAD / Air Innovations AB Manufacturing year: 2006 Total operating hours: 3450 Convection capacity: 2 x 40.5 kW Process control PLC: Eurotherm 2216e Hot air circulation volume: 2 x 9000 m3/h Fan electric power: 2 x 2.2 kW Temperature range: 50 – 150 C Total machine length: 10 000 mm Total machine width: 1600 mm Convection belt material: Teflon covered metal net Convection belt length: 9 000 x 600 mm Convection belt speed: 3 – 8 m/s / 0.25 kW, inverted controlled Heated width: 650 mm Inside / free height: 80 mm (from belt to nozzles) Return conveyor: Habasit FAB-8EO WV Return conveyor dimensions: 12000 x 600 mm (Teflon) Return conveyor drive: 0.25 kW, 380 V/50 Hz.
Drum and Container Filling Line, Semiautomatic YOC 2006 The line is designed for filling both 1000 liter IBC’s and normal 209 liter drums / barrels. It consist of straight chain driven heavy duty roller conveyor which is carrying IBC’s or a standard pallet loaded with four drums / barrels through the filling process and conveying them for further storing. The filling machine is semiautomatic coarse-and-fine filling station; first is programmable volumetric and then fine filling with integrated weighing system. Cap closing / bunging and sealing will be made manually but a machine aided. The station operation is controlled by Siemens S7C programmable logic. The line is manufactured in 2006 by Finnish company “Insinööritoimisto Jyrki Kekälainen” who is specialized supplying automation solutions filling and packing applications. Operation description: The operator lifts the empty containers on the conveyor (open the cap of container), the container will move into filling machine and it will be filled automatically with 2 "and 1 / 2" valves, coarse-and fine-filling. After filling the container will move out of the machine and the operator will fix the label and close the cap. After the filling station there is ~16 m long puffer conveyor for the filled IBC`s, where a fork lift will pick up the IBC`s In drum filling the operator lifts the empty drums on pallet (open the caps). Then he lifts the pallet on the conveyor. In the machine there is an extra filling lence for the drums. The drums are filled on the weighing system of the machine which is controlling the filling of each barrel. After the drum is filled the operator move the lence into second drum and machine start to fill it. After all drums are filled the pallet will move out of machine and the operator will close the caps and fix the seals and labels. Technical data: Manufactured in: 2006 Suitable for: Standard IBC and Drums Max filling weigh: 1500 kg Filling accuracy: 0.5 kg Filling capacity: 7 IBC/hour or 35 Drums (209 liters) / hour Roller conveyor type: Chain Driven, Galvanized Roller conveyor length: Approx 16 meters Roll diameter: 80 mm.
Yogurt production and packaging line 4000 l / shift 0732010 Yogurt production and packaging line 4000 l / shift Yogurt production equipment consists of 4 pcs 1000 liters of yogurt fermentation tanks, transmission equipment and a fully automated filling line 150 - 200 grams plastic cups. Process operation requires two people and equipment can be made about 4000 liters (or 20000 pieses) of 200g canned yogurt cups or other similar product for a normal 8-hour working shift. Packaging equipment is manufactured in the 1980s by German Ganzhorn & Stirm (nowadays Casti) and an automatic product cup feeder has been added later on the line. Also the tray feeding device has been recently added. The production line is fully operational and suitable besides for yogurt production, also for all curdled / fermented milk packaging in 150g-200g cups. Fermentation tanks are double walled 1000 liter stainless steel vertical tanks. The product temperature can be adjusted as desired (e.g.36C) by using heating water between double walls. Control valves are manually adjusted. The fermented yogurt is transferred to two 100 liter feeding tanks of the packing line with gentle rotary lobe pumps. Filling the yogurt cups is fully automated 2-lane packing process. The main equipment are manufactures by German Canzhorn & Srimin. Later installed automatic cup feeding equipment places 150 gr - 200 gr cups in 2 rows on the filling machine. The filling machine fills cups in three phases; first to the bottom desired volume of jam and then two different layers of product mass. ( 3-layer of yogurt). The cups are closed with aluminum lids which is sealed with electric heater. Transfer conveyor moves closed cups on to a palletizing machine which loads 20 cups on each cardboard or plastic tray (tray is automatically fed by a tray feeding device) where full trays are moved to a stacker machine which piles several layers of trays (up to 1 meter tall) for transportation. Technical Specifications: The manufacturer: Ganzhorn & Stirm (Casti) Filling machine type: DOGatherm 61 Stacker type: BE 75/2 Production capacity: up to 4000 liters / shift Yogurt fermentation tanks: 4 x 1000 liters Cups & filling: 150 - 200 g / max. 3-layer filling Filling line length: about 12 meters.
coco peat, coconut husks chips, coir fiber, geo textiles and grow bags, amw coir goods exports has been widely known since 2015 for its excellence as a coir and coco peat manufacturer and exporter in sri lanka. the unquestionable quality of our coir and amw products are based on the creation of products using the quality controlled, purest coir from the land of srilanka, known for its rich source of coir and coco peat. deliverance of the highest quality coir and coco peat while ensuring that products are of reasonable pricing has been our goal since the beginning and we are looking forward to further nourishing our customer service satisfaction by providing the best sorted coir at the best price available as we value the customer requirements..
