1. Main technical parameters, Model: DL-7802B-6A13, Product Name: Wire Bending Testing Machine (Wire Swing Testing Machine), Test angle: 0~± 180 can be set arbitrarily, and the left and right angles can also be set to be inconsistent, Test speed: 0-100 times/min, set arbitrarily, Station: 6 stations in total, with each group recording the number of tests separately, Independent testing: Each group can be tested independently, and 6 groups can also be tested simultaneously, Counting setting range: 1~99999999 times, any setting, Shutdown method: Broken wire shutdown, can switch between single broken wire shutdown and 6 sets of broken wire shutdown, Weights: 6 each for 50g, 100g, 200g, 300g, and 500g, Machine size: 1400 450 1300mm (length, width, height), Machine weight: 130kg, Power supply: 1 AC220V 2A or specified, 2. Equipment Introduction The 360 degree swing testing machine meets the requirements of relevant standards such as UL817, such as "General Safety Requirements for Flexible Cord Components and Power Cords". Suitable for manufacturers and quality inspection departments to conduct bending life tests on power cables, DC cables, headphone cables, USB cables, etc. Used to test the reliability of wire products under specified speeds, angles, and weights.
Model: DL1220S Product name: Fully automatic insertion and extraction force testing machine Maximum test stroke: 0-150mm Maximum test speed: 0-300mm/min Maximum test load: 50kg Minimum fine adjustment distance: 0.01mm X-axis travel distance: 0-75mm Y-axis travel distance: 0-75mm Load units: N, lb, gf, Kgf can be freely switched Transmission mechanism: ball screw Power system: stepper motor Machine weight: 80kg Machine size 400 * 300 * 980mm Power supply 1 AC220V 2A or specified 2. Introduction This machine is suitable for testing various types of connectors, such as insertion force, extraction force, plastic retention force, and service life. Through computer analysis, it can accurately measure the load, stroke, and corresponding change curve of the tested object. It can also accurately control the stroke, speed, target measurement times, and pause time of connector insertion and extraction force testing. Especially with various specialized clamps and fixtures, the connectors can be more automatically centered and aligned during testing, without the problem of "eating one side" occurring. By using the Chinese screen settings in Windows, the operation is simple and convenient, and all data can be stored (such as test conditions, displacement, curve plots, life curve plots, inspection reports, etc.), making it a reliable high-performance testing instrument. Equipped with a dynamic impedance testing system, it can test the insertion and extraction force while also testing the dynamic impedance and drawing (load stroke impedance curve diagram)
Model: DL3020, Stroke mm: 300 * 200 * 200, Boundary dimension mm: 625 * 777 * 1080, Workbench mm: 460 * 360, Total weight (kg): 280KG, Glass bearing capacity (kg): 15, Z-axis lifting distance: 200MM, Working distance: 90 mm, Measurement accuracy UM: XY (3+L/200) um, Resolution of grating ruler: 1um, CCD resolution industrial grade: 800 line high-definition, Zoom objective magnification: 0.7-4.5X, Total magnification: 20-180 times, optional 20-220 times, Object field of view: 7-1.1MM, Surface light and contour light of the light source: white LED, with continuously adjustable brightness, Power supply: 220V �± 10%, 50 Hz. Electrical equipment requires reliable grounding: the grounding resistance is less than 4 ohms, Working environment: temperature 20 â??�± 5 â??, temperature change ï¼? 2 â??/hr, humidity 30-80%, vibration ï¼? 0.002g and lower than 15Hz, Imager characteristics: Utilize optical principles for non-contact measurement; Suitable for all fields with the purpose of two-dimensional measurement; It is the best measurement solution for small, thin, soft, and component parts; Accurate measurement can be achieved for elements such as points, lines, circles, angles, etc; And it has powerful report output function, high-quality, economical, and practical; Ultra high cost-effectiveness with all functions of flat measurement. imager: measure all plane dimensions; Hardware, main features: Fully cast aluminum worktable, column combination lightweight body. Precision transmission equipment design for fast movement. Precision P-level linear guide rail and V-shaped guide rail, with extremely high straightness, Ensure machine accuracy and service life. Sony Color CCD from Japan, with higher definition measurement images. Flexible lighting with contour light, surface light, and coaxial light (optional), high clarity, and unparalleled measurement accuracy. High precision optical ruler, every 1 micron is crucial.
b. Technical parameters: Measuring area: x=500mm, y=600mm, z=400mm Overall dimension: 1250 X 1380 X 2380 mm Workbench load-bearing Max Part Weight: 800kg Machine weight: 1800kg Length accuracy MPEe: â?¤ 1.7+L/300ï¼? �¼ M) Detection ball accuracy MPEp: â?¤ 2.5 �¼ M Scale resolution: 0.1um Max 3D Speed: 500mm/s Max 3D Acceleration: 900mm/s �² c. Advantages: Patient double passive vibration damping: The use of coordinate measuring machines is mainly in production factories, which inevitably leads to vibrations caused by nearby machine tools or transport vehicles, which has a fatal impact on the accuracy of coordinate measurement. Building earthquake resistant foundations is a basic idea, but it will increase additional costs and trouble. Our three coordinate support adopts a dual passive damping mechanism to prevent the impact of low-frequency vibration, greatly ensuring measurement accuracy and reducing the trouble of taking seismic foundation measures. High quality granite workbench: The granite work platform is the overall support of the machine, and its quality affects the overall performance of the machine. Our three-dimensional granite material is processed as a whole, stress free, rust and corrosion resistant, easy to maintain, low thermal expansion coefficient, and small deformation affected by temperature. Effectively reducing the vibration of the measuring machine and improving the performance of the entire machine DL-654 is a high-end bridge type coordinate measuring machine developed and designed independently. During the production process, every component is strictly screened, and during the assembly process, it ensures perfect and reasonable connection between the components. Then, it is calibrated according to the ISO10360-2 standard, using high-precision laser interferometers for calibration. Later, it is also tested using standard testing tools (square rulers and step gauges) certified by the DKD organization. Therefore, the final customer will use genuine German technology, high-quality, and high-precision coordinate measuring machines.
modelDL313082T Maximum compressive strength2T Degree of decomposition1250000 Testing accuracy05 Operation modeMicroprocessor Unit switching KgNLBKN Test spaceLWH8008001000mm Compression speed standard 103mmmin Report ItemsSerial number peak value average value set pressure holding value memorable Structure and controlMicrocomputer operating system servo motor ball screw Safety devices Overload protection overvoltage protection limit protection device External dimensions LWH14008001700mm Motor power 400W Net weight 400Kg source AC220V10 2 Product Usage The cardboard box compression testing machine is the most direct testing instrument for checking the compressive strength of cardboard boxes or other packaging containers It is used to determine the compressive capacity of cardboard boxes and can be used for testing the holding pressure stacking The test results can be an important reference for the height of finished packaging boxes stacked in factories or an important basis for designing packaging boxes It can execute national or international standards such as GB ISO ASTM BS DIN JIS for testing and is an ideal testing and research equipment for various factories technical supervision departments commodity inspection institutions research institutes and colleges and universities 3 Product features 1 The machine structure adopts an aluminum extruded sealing plate treated with advanced baking paint with builtin highprecision low resistance gapless double ball screws and guide columns improving load efficiency and structural rigidity 2 The control system adopts Panasonic digital AC server to control high response frequency AC motors ensuring high efficiency smooth transmission low noise and speed accuracy within 02 of the transmission system 3 The microcomputer system uses a commercial computer as the main control machine combined with our companys TM testing software to complete all experimental parameter settings working state control data collection and analysis processing result display and printing output 4 The product performance is stable and reliable with high measurement accuracy powerful testing software functions and easy to understand operation
Maximum test force:10KN Force unit:N Kgf ibf N KN Testing accuracy:Not greater than 1% of the total range Test itinerary:1100mm without fixture Print Project:After saving the data, it can be printed and converted into a PDF document Test speed:0-300mm/min computer settings Shutdown method:Automatic shutdown due to fracture control mode ;PC control Power source :Stepper motor Transmission mode :Ball screw drive Host size :Approximately 800 * 500 * 1550mm; Display method:Computer full Chinese display Testing items: Real time value, maximum value, fracture value, elongation, tear strength, proportion of fracture points, etc 2.1. Purpose: Test the tension, pressure, shear, peeling, tearing and other tests of metal, wire, leather, fabric, plastic and other products, and comply with various tensile and pressure testing standards. PC control, can input testing standards into the system, and conduct testing according to different standards. 2.2 Characteristics: This machine is driven by a stepper servo motor, ensuring smooth operation and low noise. The key components of this machine are all high-quality and reliable products, making your experiments precise and effective. This machine is fully computer-controlled and can save and print test data.
2.3 Technical parameters: Maximum test force: 50kg, 100kg, 200kg (choose any one) Force unit: Kgf bf N Test itinerary :1000mm without fixture Print Project: Print after saving data Test speed :0-500mm/min can be set Shutdown method: Automatic shutdown due to fracture control mode : PC control Power source :Stepper motor Transmission mode :Ball screw drive Host size: Approximately 500 * 500 * 1430mm; Display method :Computer full Chinese display (or English system) Testing items: Real time value, maximum value, fracture value, elongation, tear strength, proportion of fracture points, etc 2.1. Purpose: Test the tension, pressure, shearing, peeling, tearing and other tests of wires, leather, fabric, plastic and other products, and meet various tensile and pressure testing standards. 2.2 Characteristics: This machine is driven by a precision motor, ensuring smooth operation and low noise. The key components of this machine are all high-quality and reliable products, making your experiments precise and effective. This machine is fully computer-controlled and can save and print test data.
4.Main technical parameters 4.1. Capacity: 5, 10, 20, 25, 50100200kg (optional) 4.2. Unit switching: kg, N, LB 4.3. Load decomposition degree: 1/250,00 4.4. Load accuracy: 0.25% 4.5. Maximum stroke: 1000mm (excluding fixtures) 4.6. Test speed: 30-300 mm/min 4.7. Displacement resolution: 0.01 mm 4.8. Display device: touch screen (capable of displaying and printing test times, test values, maximum values, fracture values, etc.) 4.9. Motor: AC motor 4.10. Overall dimensions (L * W * H): 550 * 500 * 1240mm 4.11. Weight: 80kg 4.12. Power supply: 1 , 220V, 15A or specified 4.13. Delivery: One set of tension fixtures 5. Introduction to System Functions 5.1. It has tensile and pressure testing functions. 5.2. It has a pull stop function. 5.3. It can display displacement, has functions such as elongation, pressure, and other material testing machines. 5.4. There is an automatic stop alarm function for overload load setting. 5.5. It has an automatic save function, and can coexist with manual and automatic testing data up to ten times. 5.6. Use a list format to display the saved test data. 5.7. With an administrator password, users can modify their startup password to make machine management more secure. 5.8. Using software to calibrate the load value is extremely easy to calibrate. 5.9. The internal functions are set with full Chinese prompts, making the operation convenient and simple. 5.10. Rich testing functions, capable of conducting tensile tests, pressure tests, compressive tests, elongation tests, etc. 5.11. Display method: Real time display on the touch screen. 5.12. Tensile range: Standard configuration 200kg (optional). 5.13. The accuracy is 1/25000. 5.14. It can print test data and dates, making it easy to view test data for each stage 5.15. Conversion of three types of force units: N, Kg, and LB. During the testing process, 5 sets of test data at any position can be manually and automatically captured and printed. 7. Introduction This product tests the tensile strength, compressive strength, and elongation of various materials, semi-finished products, and finished products. It can perform tests such as peeling, tearing, bending, bending, and compression, and is suitable for use in industries such as metals, plastics, rubber, textiles, synthetic chemicals, wires and cables, leather, etc. 8. Design standards ASTM D903, GB/T16491, GB/T1040, GB/T8808, GB13022, GB/T 2790/2791/2792, CNS-11888, JIS K6854, PSTC-7, etc
Temperature range :RT~450 Temperature fluctuation : ±0.2 Temperature uniformity : ±1 Temperature display resolution: 0.1 Time display resolution:0.1S Barrel diameter: .095 ±0.005mm Outlet length: 8.000 ±0.025mm Loading cylinder diameter: 9.550 ±0.025mm Weight accuracy: ±0.5% Data output method:Micro automatic printing output Cutting method Integrated manual and automatic cutting Test load 8 levels in total, 8 sets of weights
Technical parameters Maximum test force 1000kg Unit of force N Kgf bf N KN Test accuracy Grade 0.1 Test stroke 2200mmWithout fixture Print items Save the data and then print, can be converted to PDF document. Test speed: 0-500mm/min computer Settings Shutdown mode: Break automatic stop Control mode PC control Power source servomotor
T2 Inclined Moving Walk GRACES is outstanding for is beaulful appearance and superior performance. The specially designed combs and escalator structure ensure the entire escalator more firm and anti-slip. Features Of T2 Inclined Moving Walk The diversilied specification of GRACES not only offers for various malls but also used for railway station, airport and subway with public heawy duty characters. GRACES (ravelator/moving walk) is designed for heavy taffic areas which incduded the airport, metro station and subway. It features a space-saving, environmentally sound design. The T2 Inclined Moving Walk features a robust and durable construction, ensuring long-lasting performance and reliability. Its advanced engineering design allows high load-bearing capacity to ensure continuous transportation of passengers. In addition, the moving walkway is equipped with more than 30 safety features to provide passengers with a safe and comfortable experience. The product is intelligently designed with attention to aesthetics and functionality. It has a sleek and modern appearance, blending seamlessly with the surrounding architecture. The moving walk is also energy-efficient, contributing to sustainable and eco-friendly transportation solutions. IFE Elevator's T2 Inclined Travelator is a public transportation solution designed to increase mobility and convenience on different floors. Its durability, safety features, aesthetic appeal, and energy efficiency make it a reliable choice for those in need of inclined transportation systems. Specification Of T2 Inclined Moving Walk Specification T2 Lifting height range/m 1.5H9.5 Use segment length/m 50 Tilt angle/° 40494 Nominal width/mm 800/1000 Nominal speed/m/s 0.5 Applicable environment Indoors The type of work Normal type Handrail structure Vertical armrests Drag method Y-/VVVF Startup mode Standard single speed Standard self-starting Frequency conversion low speed Frequency conversion self-starting Number of horizontal steps as standard H6m -- H>6m -- Pedal depth/mm as standard 266.67 Additional brakes H6m No H>6m Yes Truss deflection 1/750 Safety factor for moving parts 5 Now the price of passenger escalator is reasonable, if you want to buy new escalator, please contact us. As an elevators company, we can provide kinds of elevators and escalators for sale, anything you need, please leave us a message.