Disposable medical gloves.
Hardwood Flooring Panels..
Wood, lumber, pellets, pallets, slates.
Never used machine. Feed capacity: approx. 35 t/h Grain size: Raw material: 0-150 �¼m Circulation material: 0-150 mm Bulk density: 1.0-1.2 g/cm2 Free moisture: 0-0.5% Temperature: 120 °C Product: Briquette > 10 mm 25 t/h fine < 10 mm approx. 10 t/h Device parameters: Roll diameter: 1000 mm Roll body width: 930 mm Maximum load: 7200 kN Rolling speed: 0.42 m/s Press: 400 kW Hydraulic system: 3 kW Roller presses are used for pressing or briquetting various types of coal, minerals, ores and mixtures with binders. In order to achieve sufficient breaking strength by pressing or briquetting, products with low surface moisture are suitable for handling. Depending on the input material and the final product, roller presses can be equipped with optional functions. The material fed into the screw is a mixture of gypsum hemihydrate and gypsum dihydrate. The arrow screw lifts the material and pushes it into the area between the two rollers. Briquettes are created by pressing the material in the gap between the cylinders. A certain part of the material leaves the press through the gaps of the trough forms. The subsequent screening process is performed with a 10 mm cut. Adapting the press to the overall system as part of the trial run is extremely important to deliver a product that meets quality requirements. Interruption of the briquetting process due to a lack of material leads to disruption of the material flow as well as excessive stress on the roller press. The technical description of control and regulation of the roller press, including accessories, is part of the specification of the independent energy and control system supplier.
Never used machine. Feed capacity: approx. 35 t/h Grain size: Raw material: 0-150 �¼m Circulation material: 0-150 mm Bulk density: 1.0-1.2 g/cm2 Free moisture: 0-0.5% Temperature: 120 �°C Product: Briquette > 10 mm 25 t/h fine < 10 mm approx. 10 t/h Device parameters: Roll diameter: 1000 mm Roll body width: 930 mm Maximum load: 7200 kN Rolling speed: 0.42 m/s Press: 400 kW Hydraulic system: 3 kW Roller presses are used for pressing or briquetting various types of coal, minerals, ores and mixtures with binders. In order to achieve sufficient breaking strength by pressing or briquetting, products with low surface moisture are suitable for handling. Depending on the input material and the final product, roller presses can be equipped with optional functions. The material fed into the screw is a mixture of gypsum hemihydrate and gypsum dihydrate. The arrow screw lifts the material and pushes it into the area between the two rollers. Briquettes are created by pressing the material in the gap between the cylinders. A certain part of the material leaves the press through the gaps of the trough forms. The subsequent screening process is performed with a 10 mm cut. Adapting the press to the overall system as part of the trial run is extremely important to deliver a product that meets quality requirements. Interruption of the briquetting process due to a lack of material leads to disruption of the material flow as well as excessive stress on the roller press. The technical description of control and regulation of the roller press, including accessories, is part of the specification of the independent energy and control system supplier.
Automobile spare parts, genuine spare parts for cars and trucks like spark plugs, engine oils, lubricants, seal and gasket kits, timing belts, fuel injectors, suspension bushings, shock absorbers, brake pads, headlamps, fuel and water pumps, air and oil filters, engine and gearbox mounts, tensioner assemblies, crankshaft and wheel bearings, stabilizer links, thermostats, ignition coils, oxygen sensors, radiator grilles, windshields, hydraulic fluid, engine repair kits, control units..
Glass & mirrors.
