Vertical Submerged Pump Suppliers and Manufacturers

Vertical Sump Pump or Long Shaft Pump. We manufactured vertical pumps for the applications with low net positive suction head, cryogenic temperatures where vertical lift is required and in also in sump and cooling water services. Our vertical pumps is specially designed for service in water, chemicals, sewage and slurries. Vertical pumps are cover a wide range of hydraulic condition to meet virtually every pumping service in the industry and optimum efficiency.

Tobee 40mm vertical submerged chemical pump works underwater for delivering heavy concentration abrasive & corrosive slurry with big particles. pump column is made by steel or elastomer covered steel, For rubber lined pump, all wetted parts are made by elastomer for delivering strong corrosion slurry. Tobee 40mm vertical submerged chemical pump specification: Size: 40mm Capacity: 7.2-29m3/h Head: 4-28.5m Speed: 1000-2200rpm Eff.: 40% Power: Max.15kw Handling solids: 12mm Materials: High chrome alloy, Rubber, Polyurethane,Ceramic etc

Tobee 100mm vertical submerged chemical pump is mainly used in a variety of sump conditions, It can also be readily applied on floating dewatering or other floating pump platforms. As a true cantilevered vertical slurry pump, TP100RV vertical spindle pump does not have submerged bearings or seals, thus, eliminating the primary failure mechanism for similarly fielded pump lines. Tobee 100mm vertical submerged chemical pump Specification: Size: 100mm Capacity: 40-289m3/h Head: 5-36m Speed: 500-1200rpm Eff.: 62% Power: Max.75kw Handling solids: 32mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc

Tobee 300mm vertical submerged chemical pump is unique cantilevered design, The sump pumps doesnâ??t need any seal and seal water. The TP300TV pumps are preferred by many customers with special installation requirements and widely applied in sump. Its wear-resistant metal liner could handle abrasive slurries with rough particles and high concentration. Tobee 300mm vertical submerged chemical pump Specification: Size: 300mm Capacity: 288-1267m3/h Head: 6-33m Speed: 350-700rpm Eff.: 50% Power: Max.200kw Handling solids: 65mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc

Tobee 65mm vertical submerged chemical pump is mainly used to transfer high- hardness, strong-corrosion and high-concentration liquids that contain suspended solid particles, The metal lined and elastomer rubber lined is interchageable for different duties, such as finished ores, refuse ores, ashes, cinders, cements, mud, mineral stones and etc. Tobee 65mm vertical submerged chemical pump Specification: Size: 65mm Capacity: 18-113m3/h Head: 5-31.5m Speed: 700-1500rpm Eff.: 60% Power: Max.30kw Handling solids: 15mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc

Tobee 150mm vertical submerged chemical pump are designed for every other tank, pit or hole-in-the-ground slurry handling situation, TP150SV pumps are available in various standard lengths to suit common sump depths, for very deep sumps or where high shaft speeds limit the length of the pump, a suction extension pipe can be fitted to the bottom inlet to extend the depth of the pump by up to 2 metres. Tobee 150mm vertical submerged chemical pump specification: Size: 150mm Capacity: 108-576m3/h Head: 8.5-40m Speed: 500-1000rpm Eff.: 52% Power: Max.110kw Handling solids: 45mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc

Tobee 250mm vertical submerged chemical pump is centrifugal sump slurry pumps submerged in sump to work.It is designed for delivering abrasive, large particle and high density slurries. The pumps have no need of any shaft seal and sealing water. it can also be operated normally for insufficient suction duties. The submerged depth can be customed as different sump. Tobee 250mm vertical submerged chemical pump specification: Size: 250mm Capacity: 261-1089m3/h Head: 7-33.5m Speed: 400-750rpm Eff.: 60% Power: Max.200kw Handling solids: 65mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc

Tobee 200mm vertical submerged chemical pump are an ultra-heavy duty design for continuous operation, the bearing assembly design allows the pumps to operate in very tough conditions without damaging the bearing. Both high chrome alloy and elastomer wet end parts are suitable to the different applications, and the pumps use in many industries, various lengths and suction extensions are available to suit most sump depths. Tobee 200mm vertical submerged chemical pump Design Features: Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers. Tobee selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance, and where larger particles or high density slurries are encountered. Abrasion resistant Ultrachrome T05 alloy. Abrasion/corrosion-resistant Hyperchrome T49 alloy. Corrosion-resistant stainless steels. Natural and synthetic elastomers. No submerged bearing failures The robust cantilever shaft avoids the need for lower submerged bearings which are often the source of premature bearing failure. Heavy duty roller bearings, above mounting plate. No submerged bearings. Labyrinth/flinger bearing protection. Rigid, large diameter shaft. No shaft sealing problems The vertical cantilever design requires no shaft seal. No priming required. The top and bottom inlet design is ideally suited for â??snoreâ?� conditions. Less risk of blocking The screened inlets and large impeller passages reduce the risk of blockages. Zero ancillary water costs The vertical cantilever design with no gland or submerged bearings avoids the need for expensive gland or bearing flushing water. Tobee 200mm vertical submerged chemical pump On-site Applications: Mining Sump drainage Coal prep Mineral processing Mill sumps Tunnel Tailings Chemical slurries Ash handing Paper and Pulp Waste sludge Coarse sand Lime mud Phosphoric acid Sump Dredging Mill grinding Alumina Industry Power Plant Potash Fertilizer Plant Other industries

Heavy duty submerged slurry pumps are vertical, shaft driven centrifugal slurry pumps designed for transferring abrasive and high density slurries from sumps, pits and other submersible source. The position of the shaft of the vertical slurry pump is perpendicular to the horizontal plane, the pump end is under the water and the motor above the liquid level. Features -The rotor parts can be adjusted axially and supported by multiple points, so heavy duty cantilever sump pump can operate steadily and reliably. -The pump adopts a long shaft structure and can be inserted up to 10 meters deep. Shaft coupling is safe and reliable. Convenient disassembly. -The impeller is immersed in the medium when the pump starts, so it is easy to start, and there is no air exhaust problem. -The outlet flange is a half movable flange for easy connection. Series SP(R) slurry pump is centrifugal vertical sump pump, work under fluid. It widely used for delivery abrasive, high density slurry with large particle in the metallurgy, mine, power plant, chemical, and other industry. Shijiazhuang Jiemu Machinery Equipment Co.,Ltd is one of the leading private indenting firms of China having 15 years of experience in Mining, Fluid Transportation and Fire Emergency Field. It works on design theory of slurry pump and water pump, experimental researches of pump performance wear mechanism and new products developing, and involves in research, design, manufacturing and sales.

65 QV-SP Vertical Slurry Sewage Pump is a cantilever sump pump,Which work submerged to transport high abrasive and high density slurries with large particles.It doesn't need any seal water. Hard metal lined or fully rubber lined fitted.High capacity double suction semi-open impeller design.and suction agitator is also available.

YRY series submerged pump is a single-stage single suction vertical high temperature submerged centrifugal pump. This series of pump, design professional, with excellent heat resistance, long life, high efficiency, good sealing performance, low niose, small footprint, high cooling efficiency, reasonable structure and so on. This pump is dedicated to pumping less than 500 high temperature molten salt and heal conducting oil. This pump is widely used in the technological process of phthalic anhydride, maleic anhydride, acrylic acid, acrolein, fumaric acid, melamine, refrigerants, aluminum magnesium industry, PMDA industry etc. It can also be used for transmission of heating medium in rubber, plastic, building materials and other insustries. In addition, it can be used to pumping more than 100 hot water and other heat medium. This series of pump, adopting different structures and materials according to different media. Especially for those with larger liquid depth, we have patented structure design, and that can completely replace imported products.

Type ZJ and ZJLR pumps are vertical,centrifugal slurry pumps submerged in sumps to work.They are designed for delivering abrasive,large particle and high slurries.These pumps have no need of any shaft seal and sealing water.they can also be operated normally for insufficiend suction duties. Wet parts of Type ZJL pump are made of abrasion-resistant metal. All parts of type ZJLR pump immersed in liquid are lined with rubber our liners.They are suited to transport non-edge angle abrasive slurry. Different size wooden case