Feature: 1. 100% non-toxic and environmentally safe 2.Easy to install due to its flexible, compressible nature, comes in rolls and can be cut to size or shape desired, stuff it in the hole, and youâ??re done. 3.It is a permanent solution, will not rust or corrode over time, dose not shrink, stain, pull out. 4.Made of sharp durable fibers material which is suitable to die cut to specific shapes and sizes. 5.Most consistent material for exhaust applications with strength in all directions as cross-lapped material going at approximately 90 degree angles to other fibers. 6.Installs under landscaping and allows grass and small plants to grow through, thus being an invisible force against pests. Function: 1.Fill fabric is an exclusion fabric used by professional nuisance control and pest control operators. 2.It is composed of stainless steel and poly fibers. This blend of materials gives it an extra â??spring backâ?�, allowing for easier fitting in crevices and the ability to stay in place well. Cut it 2-3 times the size of the opening to make a tight fit. 3.It is highly resilient and is an impenetrable barrier against rodents and pests. Package Roll or sheet Size 4â?�*10m per roll or as requested Width 47â?�/48â?� Weight Ranging from 2000gsm Application: Burrowing animals such as rats, chipmunks, gophers, groundhogs and nutria can dig beneath the ground and ruin landscaping, chew through cables and destroy dikes and levees. Prevent these animals from wreaking havoc beneath the ground, currently protecting many public and private sites including: Tree pits Shopping mall landscapes Planters Parks Sports fields River and canal banks Retention ponds National historic sites Outdoor amphitheatres Install instructions 1.Install it by pressing it into rodent-prone crevices with gloved hands or simple tools like a putty knife or screwdriver. 2.Do not install it close to live electrical conductors, since stainless stell is an electrical conductor. Installing IT around fully sealed electrical conduit coming out of a wall is safe.
Stainless steel tube is a hollow long strip steel made of stainless-steel material. Because of its excellent corrosion resistance, it is mainly widely used in petroleum, chemical, medical, food, light industry, mechanical instruments and other industrial transportation pipelines and mechanical structural components. In addition, when the bending and torsion strength are the same, the weight is light, so it is also widely used in manufacturing mechanical parts and engineering structures, but also commonly used in the field of furniture decoration. Stainless steel pipe is divided into seamless pipe and welding pipe according to the production mode, seamless steel pipe can be divided into hot rolling pipe, cold rolling pipe, cold pulling pipe and extrusion pipe, etc., cold pulling and cold rolling is the secondary processing of steel pipe; welding pipe is divided into straight welding pipe and spiral welding pipe. Stainless steel pipes can be divided into round tubes and different tubes according to the cross-sectional shape. The form tubes have rectangular tubes, rhomboid tubes, ellipse tubes, hexagonal tubes, octagonal tubes and various cross-sectional asymmetric tubes. It can be divided into Austenitic Stainless Steel Tube Ferritic Stainless Steel Tube Martensitic Stainless Steel Tube and Duplex Stainless Steel Tube by the type of stainless steel.
We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.
We deals in the following products of India, China, Taiwan and Korea Origin:- Stainless Steel Sheets
We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.
We deals in the following products of India, China, Taiwan and Korea Origin:- Stainless Steel Wire
We deals in the following products of India, China, Taiwan and Korea Origin:- Stainless Steel Pipes
Stainless Steel Kitchenware (Bowls) Dia 160 x 75mm 240gr / Dia 135 x 65mm 200gr / Dia 115 x 60mm 140gr / Dia 95 x 55mm 120gr Material: Stainless Steel 304 Thickness: 0.5mm Cover: PP (Polypropylene) Made In Korea
Model Number: 314 321 441 430 Type: plate Application: decoration Certification: ISO Tolerance: 1% Processing Service: Bending, Welding, Decoiling, Punching, Cutting Product name: aisi 314 321 441 430 stainless steel sheet Surface: 2B, NO.4 HL available Technique: Cold Rolled Finish Material: Stainless Steel Color: Natural Color Edge: mill Edge/ slit edge Item:ISO9001 Standard Packing: Standard Export Packing Ni:min1%
Stainless Steel Round Tube
Stainless Steel Square Tube
Stainless Steel Rectangular Tube
Product Stainless Steel coil Surface Finish 2B, BA, NO.1, NO.4, 8K, HL, Embossing, Satin, Mirror, ect Technique Cold Rolled, Hot Rolled Steel Grade 200 series: 201 202 300 series: 301 304 304L 309 310 310s 316 316L 321 400 series: 409 410 410S 420 430 439 443 Duplex:3RE60(Cr18) SAF2304 (Cr23)SAF2205 (Cr22) SAF2507(Cr25) Color Golden, Black, Sapphire Blue, Brown, Rose Gold, Bronze, Silver, ect Processing Type Cutting, bending,stamping,welding,cnc machining Cutting Type Laser cutting;water-jet cutting;flame cutting Application Interior Exterior decoration, Architecture; Evevator; Kitchen, Ceiling, Cabinet, Advertising nameplate, Roof structure, Lead Time 7-15 working days
Stainless Steel Strip The properties of stainless steel are corrosion resistance, high ductility, attractive appearance and low maintenance. Stainless steel contains chromium which provides the properties of corrosion resistance at high temperatures. Stainless steel can withstand corrosive or chemical environments due to its smooth surface. Stainless steel products are safe for long-term use with excellent resistance of corrosion fatigue. Other specifications are also available up to request Hot Rolled Strip Available Size Width: 16.0~609.6 mm Thickness: 2.5~10.0 mm Available Steel Grade: 304, 304L, 316L Surface Finish: No.1 Cold Rolled Strip Available Size Width: 4.0~609.6 mm Thickness: 0.1~3.0 mm Available Steel Grade: 201, 202, 204 Cu3, 301, 304, 304L, 310S, 316L, 321, 409L, 410S, 420J2, 430, 439, 441, 444, 445 Surface Finish: 2B, 2D, BA, No.3, No.4, No.5, SB, HL
We are glad to propose 500 MT of stain less steel mill scale. Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products. At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel. The recovery ratio after melting in furnace for the most valuable alloy elements is: - Ni: 3.5 - 4.5% - Cr: 6-8% From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows: Waste code: 10 02 10 The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers. Chemical analysis of the material is available on request.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness: 0.3-60mm Width: 500-2000mm or customized Length: 1000-6000 or customized Standard size: 1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application: Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
StandardASTMROSHAISIDINENGBJIS LengthCustomized Thickness 005300mm Width Customized Surface 2BBANO3NO4HLNO1Mirror Material 3040Cr18Ni9A182F304SUSF30414301 Hardness 14H12H34HHO Chemical Composition Grade C Si Mn P S Ni Cr Mo Cu N Ti SUS304 008 100 200 0045 0030 80100 1820 Mechanical Properties Grade State Hardness HV Yield Strength Tensile Strength Enlongation SUS304 ANN 200 205 520 40 14H 200250 225 550 35 12H 250310 470 780 6 34H 310370 665 930 3 H 370430 880 1130 Surfce Finish Definition Application 2B Those finishedafter cold rollingby heat treatmentpicking or other equivalent treatment and lastly by cold rolling to given appropriate luster Medical equipmentFood industryConstruction materialKitchen utensils BA Those processed with bright heat treament after cold rolling Kitchen utensilsElectric equipmentBuilding construction NO3 Those finished by polishing with No100 to No120 abrasives specified in JIS R6001 Kitchen utensilsBuilding construction NO4 Those finished polishing so as to give continuous polishing streaks by using abrasive of suitable grain size Kitchen utensilsBuilding constructionMedical equipment HL Those finished polishing so as to give continuous polishing streaks by using abrasive of suitable grain size Building construction NO1 The surface finished by heat treatment and picking or processes corresponding there to after hot rolling Chemical tankpipe
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness:0.3-60mm Width:500-2000mm or customized Length:1000-6000 or customized Standard size:1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application:Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
The properties of stainless steel are corrosion resistance, high ductility, attractive appearance and low maintenance. Stainless steel contains chromium which provides the properties of corrosion resistance at high temperatures. Stainless steel can withstand corrosive or chemical environments due to its smooth surface. Stainless steel products are safe for long-term use with excellent resistance of corrosion fatigue. Product Specification and Steel Grade ASTM JIS AISI EN Mill\'s Standard S30100 SUS301 301 1.4310 S30400 SUS304 304 1.4301 S30403 - 304L 1.4307 S31008 SUS310S 310S 1.4845 S31603 - 316L 1.4404 201 S32100 SUS321 321 1.4541 202 S41008 SUS410S 410S - 204Cu3 S43000 SUS430 430 1.4016 S43932 - - 1.4510 S44400 SUS444 444 1.4521 S44500 SUS430J1L - - Other specifications are also available up to request Hot Rolled Strip Available Size Width: 16.0~609.6 mm Thickness: 2.5~10.0 mm Available Steel Grade: 304, 304L, 316L Surface Finish: No.1 Cold Rolled Strip Available Size Width: 4.0~609.6 mm Thickness: 0.1~3.0 mm Available Steel Grade: 201, 202, 204 Cu3, 301, 304, 304L, 310S, 316L, 321, 409L, 410S, 420J2, 430, 439, 441, 444, 445 Surface Finish: 2B, 2D, BA, No.3, No.4, No.5, SB, HL Tolerance of Width W < 100 mm 100 mm �?�?�?�¢?�?�?�?�¦ W < 1000 mm �?�??�?�?�?�± 0.10 mm �?�??�?�?�?�± 0.25 mm Chemical Composition & Mechanical Property : Steel Grade Ni% Max. Cr% Max. C% Max. Si% Max. SUS301 6.0~8.0 16.0~18.0 0.15 1 SUS304 8.0~10.5 18.0~20.0 0.08 1 SUS304L 9.0~13.0 18.0~20.0 0.03 1 SUS310S 19.0~22.0 24.0~26.0 0.08 1.5 SUS316L 12.0~15.0 16.0~18.0 0.03 1 SUS321 9.0~13.0 17.0~19.0 0.08 1 SUH409L 0.6 10.5~11.75 0.03 1 SUS410S 0.6 11.5~13.5 0.08 1 US420J2 0.6 12.0~14.0 0.08 1 SUS430 0.6 16.0~18.0 0.12 0.75 Mechanical Property (For Reference) Steel Grade N/mm 2 MIN. Tensile Stress N/mm 2 MIN. Proof Stress % MIN. Elongation HRB MAX. Hardness SUS301 520 205 40 95 SUS304 520 205 40 90 SUS304L 480 175 40 90 SUS310S 520 205 40 90 SUS316L 480 175 40 90 SUS321 520 205 40 90 SUH409L 360 175 25 80 SUS410S 410 205 20 88 SUS420J2 540 225 18 99 SUS430 420 205 22 88
StandardASTMROSHAISIDINENGBJIS LengthCustomized Thickness 005300mm Width Customized Surface 2BBANO3NO4HLNO1Mirror Material 301 sus301 X12CrNi1707Cr17Ni71431 Hardness 14H12H34HHO Grade C Si Mn P S Ni Cr Mo Cu N Ti SUS301 015 100 200 0045 0030 6080 1618 025 Mechanical Properties Grade State Hardness HV Yield Strength Tensile Strength Enlongation SUS301 ANN 250 205 520 40 14H 250310 470 780 35 12H 310370 510 930 10 34H 370430 745 1130 5 H 430490 1030 1320 3 EN 490550 1275 1570 Surface Finish Surface Finish Definition Application 2B Those finishedafter cold rollingby heat treatmentpicking or other equivalent treatment and lastly by cold rolling to given appropriate luster Medical equipmentFood industryConstruction materialKitchen utensils BA Those processed with bright heat treament after cold rolling Kitchen utensilsElectric equipmentBuilding construction NO3 Those finished by polishing with No100 to No120 abrasives specified in JIS R6001 Kitchen utensilsBuilding construction NO4 Those finished polishing so as to give continuous polishing streaks by using abrasive of suitable grain size Kitchen utensilsBuilding constructionMedical equipment HL Those finished polishing so as to give continuous polishing streaks by using abrasive of suitable grain size Building construction NO1 The surface finished by heat treatment and picking or processes corresponding there to after hot rolling Chemical tankpipe
