A type of basic resin.It is colorless or light yellow with low toxicity.It is widely in many fields such as coating,paint and antisepticising. Brand: Solid epoxy resin CYD-011 Epoxy equivalent(g/eq): 450~500 Hydrolysable chlorine, wt% : 0.1 Softening point(C):60~70 Soluble viscosity  (25C): D~F Volatile, wt% 0.6 Color (gardner) 0.5 Equivalent to the product of other company: DER671(DOW);1001(SHELL);NPES901;E-20
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
A type of basic liquid epoxy resin. It is colorless and light yellow viscous liquid with low toxicity. It is mainly used in coating,adhesive,antisepticising,electric insulation.Laminated plates and potting fields as well as the raw material for high-grade epoxy resin processing. Brand : CYD-128 Epoxy eqiovalent(g/eq) :184~194 Hydrolysable chlorine,wt% : 0.1 Viscosity (mPa2C) :11000~14000 Volatile,wt% : 0.2 Color(Gardner) : 0.1 Brand : CYD-127 Epoxy eqiovalent(g/eq) :180~190 Hydrolysable chlorine,wt% : 0.1 Viscosity (mPa2C) :8000~11000 Volatile,wt% : 0.2 Color(Gardner) : 0.1 Brand : E-44 Epoxy eqiovalent(g/eq) :210~240 Hydrolysable chlorine,wt% : 0.3 Viscosity (mPa2C) :11000~14000 Soften-ing point(C) :12-20 Volatile,wt% : 0.2 Color(Gardner) : 0.1
N,N-Dimethylaniline DMA CAS 121-69-7 is an organic chemical compound, a substituted derivative of aniline. It consists of tertiary amine, featuring dimethylamino group attached to a phenyl group. It is an important precursor to dyes such ascrystal violet. N,N-Dimethylaniline is yellow to brown colored oily liquid with a fishlike odor. Less dense than water and insoluble in water. Flash point 150�°F. Toxic by ingestion, inhalation, and skin absorption. Used to make dyes and as a solvent. Specification Appearance Colorless to pale yellow oil liquid Assay â?¥99% Aniline assay â?¤0.3% N-methyl aniline â?¤ 0.5% Water and others â?¤ 0.2% Application 1) As dyes intermediate used for the manufacture of vanillin, azo dyes, triphenylmethane dyes etc. As an important intermediate for dyestuff, mainly used in the production of triphenyl methane dyestuff, also as solvent, antiseptic for metal, solidity for epoxy resin and polyester, and catalytic promoter for polyreaction of ethylene chemical compound. 2) In medical industry, it is used in the production of cephalosporin V, sulfanilamide -6-methoxamine pyrimidine, fluorine pyrimidine. 3) In perfume industry, it is used in the production of vanilla, as well as the vulcanized agent for rubber or the raw material for dynamite and some organic intermediates.
The epoxy resin table is a combination of epoxy resin and solid wood. The shape of the epoxy table often follows the natural live edge of the tree.
WQ-869 Specification of Water Based Solid Acrylic Resin Confidential It is recommended that WQ-869 and Joncryl@HPD696 are replaceable to each other as they have the same performances (Joncryl @HPD696) WQ-869 is a high molecular composition acrylic resin which can improve pigment dispersition, maintain a fine gloss and sustain paint stability. The combination of high pigment loading and low viscosity will allow the manufacturers to strength color settlement with delicate gloss finish, meanwhile, the formulating flexibility will not be decreased in one way or another. Paint made from WangQin acrylic polymers and resins is superior to any traditional resins with regard to liquid flow, stability, gloss finish and solubility. The paint processing control and stringent quality assurance have guaranteed a consistent and reliable product quality. Whether applied to screen printing, flexo printing or gravure printing, WangQin acrylic resin is capable of ensuring superior adhesion, sharpness and color rich diversity. Those benefits are well competing with brands such as BASF, HANWHA but also providing significantly and enhanced performances and improved adds-on value for investment from cost point of view. Considering similar product performances and much more cost-effective factors, it is recommended to use WangQin Water based HANWHA: S-70, S-120, S-820, S-20 WQ-869 Key Features & Benefits: Excellent Pigment Dispersition High Transparency and Super gloss efficiency Long-life Color Endurance High Molecular Weight General Information: Classic Physical Characteristics Appearance Transparent Solid Solid Content >99% Acid Value 215 Softening Point() 155 Average Molecular Weight 16500 Tg ( 102
Waterborne Acrylic Modified Saturated Polyester Resin Can be cured at between 120 150. Even higher temperature, it has good yellowing resistance. It is suitable for coil coating and can coating. It has very good results for dipping primer applications. It is also for clear gloss protective coating. Performance Advantages: Low odor LOW VOC Non yellowing, even at high temperature curing Good hardness development Applications: All kinds of baking systems Metal primer and topcoats Industrial applications Spray, roller, brush or dipping can be used. 1, Product Composition: Waterborne Acrylic Modified Saturated Polyester Resin, Cosolvent 2, Typical Data: Type of polymer Waterborne acrylic modified saturated polyester resin Non-volatile(%) 70±2 Viscosity( 25, mpa*s) 30-70* PH ---- Neutral.agent Non neutralization OH value on solids (mgKOH/g) 105 Air dry Inapplicable Cross-Linking with amino resin Applicable Grinding Applicable Drying speed better Corrosion resistance better weatherability better PS:The Viscosity with*is measured in the case of the resin diluted by equivalent amount of propylene glycol methyl ether 3, Product Properties: Good hardness (>4H), high gloss; Good flexibility; Good solvent resistance; Low temperature fast cross-linking (110. 20minutes); Excellent shear stability, can be grinded with dispersions directly. 4, Instructions: WL-182 can be diluted with water after neutralization by N,N-dimethyl ethanolamine the amount of which is about 4-5%of WL-182.It has tocombine waterborne amino resin to make baking coating. The suggested amount is about 20-30% of WL-182 by weight. The baking temperatureis above 120. The baking conditions and film properties are related with the amino resins used. Right amount of waterborne acidic catalysts canbe added when using methyl etherified amino resin(recommended adding amount is 0.5-1% of WL-182), which can accelerate solidifying. PH value of the coating system can always be adjusted with organic amine or ammonia. Viscosity of the dispersion will increase as the PH valueincreases. The resin can help to wet pigments, so wetting agent may reduce. 5, Storage: It is suggested that the product should be stored in a cool and dry weak alkaline place. The quality guarantee period is 6 months, and the expiredproducts can still be used after passing the inspections. 6, Applications: Amino-baking top coatings. 7, Note: The specification is a general introduction to the products of our company. It will be adjusted with the product improvement. Please contact with thecompany to obtain the latest product description.
One-part Waterborne Epoxy Ester Resin WL-172 epoxy coating contains the following added features: Extremely Long Lasting Flexible & Durable Water resistant High-Gloss Heat Resistant Economical Reduces Maintenance Costs Lead-free Nontoxic Rustproof One Application Only Acid & Saltwater Resistant Protects Against Environmental Hazards High Adhesion 1,Product Composition: Waterborne Epoxy Ester Resin, Cosolvent, Neutralizing Agent, Water 2,Typical Date Type of polymer Waterborne epoxy ester resin Non-volatile(%) 70�±2 Viscosity( 25â??, mpa*s) â?¤200* PH ---- Neutral.agent DMEA OH value on solids (mgKOH/g) ---- Air dry Applicable (Oxidation Cross-linking) Cross-Linking with amino resin Inapplicable Grinding Applicable Drying speed better Corrosion resistance better weatherability better PS:The Viscosity with*is measured in the case of the resin diluted by equivalent amount of propylene glycol methyl ether 3,Product Properties: Excellent anticorrosion performance, especially for the preparation of anti-rust base coating; Fast drying speed, good hardness; Excellent salt fog-spray resistance and early water resistance: Good storage stability; Excellent shear stability, can be grinded with dispersions directly. 4,Instructions: WL-172 can be diluted with deionized water or lower alcohol or alcohol ether to white emulsion. It can be dried by oxidation cross-linking addingoily/water driers at normal temperature or low-temperature baking. The oily driers need to be diluted by the solvent such as butyl alcohol or ethanolfor use. The water dispersion of WL-172 is stable at neutral or slight alkaline conditions pH value has to be carefully observed in coating production sinceprecipitation may occur if acidic pigments like carbon black are used in the system. PH value of the coating system can always be adjusted triethylamine or N, N-dimthylethanolamine. Viscosity of the dispersion will increase as the PH value increases. 5,Applications: Air-drying or low temperature baking antirust coatings. 6,Note: The specification is a general introduction to the products of our company. It will be adjusted with the product improvement. Please contact with thecompany to obtain the latest product description.
Waterborne Acrylic Modified Saturated Polyester Resin Can be cured at between 120150. Even higher temperature, it has good yellowing resistance. It is suitable for coil coating and can coating. It has very good results for dipping primer applications. It is also for clear gloss protective coating. Performance Advantages: Low odor LOW VOC Non yellowing, even at high temperature curing Good hardness development Applications: All kinds of baking systems Metal primer and topcoats Industrial applications Spray, roller, brush or dipping can be used. 1, Product Composition: Waterborne Acrylic Modified Saturated Polyester Resin, Cosolvent 2, Typical Data: Type of polymer Waterborne acrylic modified saturated polyester resin Non-volatile(%) 70±2 Viscosity( 25, mpa*s) 30-70* PH ---- Neutral.agent Non neutralization OH value on solids (mgKOH/g) 105 Air dry Inapplicable Cross-Linking with amino resin Applicable Grinding Applicable Drying speed better Corrosion resistance better weatherability better PS:The Viscosity with*is measured in the case of the resin diluted by equivalent amount of propylene glycol methyl ether 3, Product Properties: Good hardness (>4H), high gloss; Good flexibility; Good solvent resistance; Low temperature fast cross-linking (110 20minutes); Excellent shear stability, can be grinded with dispersions directly. 4, Instructions: WL-182 can be diluted with water after neutralization by N,N-dimethyl ethanolamine the amount of which is about 4-5%of WL-182.It has tocombine waterborne amino resin to make baking coating. The suggested amount is about 20-30% of WL-182 by weight. The baking temperatureis above 120â??. The baking conditions and film properties are related with the amino resins used. Right amount of waterborne acidic catalysts canbe added when using methyl etherified amino resin(recommended adding amount is 0.5-1% of WL-182), which can accelerate solidifying. PH value of the coating system can always be adjusted with organic amine or ammonia. Viscosity of the dispersion will increase as the PH valueincreases. The resin can help to wet pigments, so wetting agent may reduce. 5, Storage: It is suggested that the product should be stored in a cool and dry weak alkaline place. The quality guarantee period is 6 months, and the expiredproducts can still be used after passing the inspections. 6, Applications: Amino-baking top coatings. 7, Note: The specification is a general introduction to the products of our company. It will be adjusted with the product improvement. Please contact with thecompany to obtain the latest product description.
Type: mmw solid bisphenol-a type epoxy resin Specification: Appearance :light yellow solid granule Epoxy value(equivalent/100g) :0.115-0.130 Softening point (ball and ring method?) :88-95 Viscosity (gardner's method) :j-k Organochlorine value(equivalent/100g): =0.0028 Inorganic chlorine value(equivalent/100g) :=0.0005 Chroma(fe-co) :=4 Volatile matter (%) :=0.2
Mirror effect ink, solid epoxy resins, solid acrylic resin, water based epoxy resin, water based acrylic resin, water based alkyd resin, water based pu resin, epoxy curing agent.
Epoxies E-purge (epoxy powder for purging) Epoxy curing agent 87 Epoxy resin (for mfg powder coatings) $.66/lb. Waterborne epoxy dispersion -$.77/lb. Ortho creosol resin-$.88/lb. Ketimine curing agent $.90/lb. Epoxy resin (40% solids in mek) $.85/lb.
Solid powder coating, polyester powder coating, epoxy powder coating, art textured powder coating, metallic powder coating, epoxy resin powder coating, polyurethane series powder coating, industrial polyester tgic powder coating, building polyester tgic powder coating, fluorocarbon powder coatings.
Paints & coatings Acrylic copolymer newtonian tp resin Aluminum paste Acrylic latex emulsions (water base) Aromatic hydrocarbon resins, 105 & 114 sp Styrenated acrylic emulsions (water base) Fumed silica (treated) Trimellitate plasticizer Ground cellulose fiber (thickener) Epoxy powder coating resin ( for rebar) Fine tone t resin 100% polyester resin Acrylic resin in butyl acetate Coconut oil alkyd in butyl acetate High solids short oil alkyd Phenolic modified short oil alkyd Polyester powder Water reducible epoxy ester High solids chlorinated alkyd Vinyl acrylic latex
Insulating Solid Rod is made of ECR glass reinforced epoxy resin.We use continuous pultrusion procss .The products fullfill The standard of IEC61109.Insulator core rods also are also called fiberglass rod,FRP rod,GRP rod,fiberglass bar,Insulation rod,fiberglass stick and so on. 1. Standard: IEC61109 2. Material: E glass and epoxy resin. 3. Process: Continuous pultrusion. a- Continuous roll of reinforced fibers/woven fiber mat b - Tension roller c - Resin Impregnator d - Resin soaked fiber e - Die and heat source f - Pull mechanism g - Finished hardened fiber reinforced polymer
Insulating Solid Rod is made of ECR glass reinforced epoxy resin.We use continuous pultrusion procss .The products fullfill The standard of IEC61109.Insulator core rods also are also called fiberglass rod,FRP rod,GRP rod,fiberglass bar,Insulation rod,fiberglass stick and so on. 1. Standard: IEC61109 2. Material: E glass and epoxy resin. 3. Process: Continuous pultrusion.
Insulating Solid Rod is made of ECR glass reinforced epoxy resin.We use continuous pultrusion procss .The products fullfill The standard of IEC61109.Insulator core rods also are also called fiberglass rod,FRP rod,GRP rod,fiberglass bar,Insulation rod,fiberglass stick and so on. 1. Standard: IEC61109 2. Material: E glass and epoxy resin. 3. Process: Continuous pultrusion. Process: 1 - Continuous roll of reinforced fibers/woven fiber mat 2 - Tension roller 3 - Resin Impregnator 4 - Resin soaked fiber 5 - Die and heat source 6 - Pull mechanism 7 - Finished hardened fiber reinforced polymer Specifications: 1.Color: light green or brown. 2.Length: according to Customer requirement. 3. We offer customized products,including the new size, New surface treatment, Jointing the fitting, screw or mechanical.
Insulating Solid Rod is made of ECR glass reinforced epoxy resin.We use continuous pultrusion procss .The products fullfill The standard of IEC61109.Insulator core rods also are also called fiberglass rod,FRP rod,GRP rod,fiberglass bar,Insulation rod,fiberglass stick and so on. 1. Standard: IEC61109 2. Material: E glass and epoxy resin. 3. Process: Continuous pultrusion. Process: 1 - Continuous roll of reinforced fibers/woven fiber mat 2 - Tension roller 3 - Resin Impregnator 4 - Resin soaked fiber 5 - Die and heat source 6 - Pull mechanism 7 - Finished hardened fiber reinforced polymer Specifications: 1.Color: light green or brown. 2.Length: according to Customer requirement. 3. We offer customized products,including the new size, New surface treatment, Jointing the fitting, screw or mechanical.
2-Methylimidazole Molecular Formula: CH3C3H3N2 molecular weight:82.1048 CAS No. 693-98-1 solid nature. The temperature of 142 ° C to 143. The boiling point of 267 ° C to 268. Dissolved in water, ethanol, benzene-soluble cold. use of a drug metronidazole intermediates, as well as epoxy resins and other curing agent. toxic toxic, cause allergic skin reactions, and its toxicity was similar diamines. I LD50 mice to 1400mg/kg, intraperitoneal injection of extractive LD50. Operators should wear
Epoxy floor coatings are typically comprised of two main components, resins and hardeners. When these two component are mixed together during the epoxy floor coating application process, a chemical reaction begins. This chemical reaction turns the epoxy floor coatings into tough, rigid, and plastic-like materials, which are very durable, waterproof, and chemically resistant. Coz available in a variety of colors and styles, many commercial or industrial or industrial facility are use this coating to create a durable and attractive flooring surface, to make the original floor more functional. Topu epoxy floor system are generally consists of three parts, primer, second and top coat. Through grinding or mending the origin concrete floor, smooth uneven surfaces and remove dirt, oil, and other debris from concrete floors. We use the primer to repair the ground, smooth and improve the adhesion ability; then use second coat to increase solid degree of the whole system, and the topcoat give out the appearance of optional color, and covering the entire system to create a durable and attractive flooring surface.
