Overview Type NDX pump is applicable for pumping clean water and liquids whose physical and chemical properties are similar to water and without solid particles. This series of products can be used in factories,mines,urban water supply and drainage,HAVC,industrial softened water and farmland irrigation and drainage,etc.It can also be used in pressure stabilization and water supply systems of urban fire control. Pump with the same specification can change the performance parameters by cutting the outer diameter of the impeller;the normal speed of the pump is 1450RPM and 2900RPM, if it is required to operate at the maximum speed of 3550RPM(60Hz power supply or with gasoline and diesel engine),our company can provide technical instruction on the change of the outer diameter of the impeller The type NDX pump features simple structure,reliable performance,small volume,light weight,high efficiency,good ati-cavitation performance, low power consumption and convenient use and maintenance The pump is suitable for pumping medium at temperature of -10~85â?? and working pressure of 1.0MPa,if there is a need to increase to 1.6MPa or higher,please specify when selecting and ordering Performance  Capacity: 5-1650m3/h  Head: 5-135 m Product Features Energy efficient: Applying the most advanced NRCE design software and CFD fluid simulation software to develop and design the high efficiency hydraulic model,through the analysis of pump flow field,temperature field and strength,thermal deformation,fracture,rotor dynamics,etc,to achieve high efficiency ,reliability and wide efficiency zone,we have made the pump satisfy the efficiency and reliability requirements of centrifugal pump operating under design conditions and non-design conditions, reaching the international advanced level. Rear opening type structure:The maintenance is convenient,It is not necessary to disassemble the suction and discharge pipes during maintenance to pull out the rotor parts for maintenance Quality assurance:Before casting,the imported chemical analysis of the materials was carried out by the direct reading spectrum analyzer introduced from Britain to ensure that the material composition meets the requirement.The pump impeller and rotor components are tested by precise dynamic balance test,so the pump can run more smoothly, have less vibration and noise and longer service life. Product orientation:Improve the technical level of the domestic equipment industry, effectively serve equipment and processes to meet the needs of safety,reliability,energy conservation and environmental Protection.
Product Description Pump type EA series single stage end suction centrifugal pump Design Standard European standard BS EN733/DIN24255 Structure Horizontal,Axial End-Suction,Single-Stage,Volute Casing,Back pull-out Discharge Size DN32~300mm Flange DIN2501 PN16 GB/T17241.6 PN1.6 Casing Cast Iron standard,Ductile Iron/ASTM304/ASTM316 options on request Impeller Brass standard,Cast Iron/ASTM304/ASTM316 options on request Shaft ASTM420 standard,ASTM304/ASTM316/ASTM1045 options on request Shaft Seal Mechanical Seal standard,Gland Packing options on request Flow Rate(Q) 4~1584m3/h Head(H) 2~150m Speed 1450/2900rpm(50Hz);1750/3500 rpm(60Hz) Max Temperature 85�°C(standard);105�°C(option on request) Working Pressure 1.0MPa(standard);1.6MPa(option on request) Conveying Medium Clean water or liquids similar to clean water in physical property Advantage Interchangeable parts,high effective,high performance,voice-saving, easily installed and maintained Applications Water supply and drainage,HVAC and Cooling Tower,marine-Ballasting&Bilge,booster and pressurization set,irrigation and agriculture,fire-fighting system,plants,mines,food and chemical industry(with stainless steel),etc.
Ih single stage single suction centrifugal pump Detailed product description Is ih single stage single suction centrifugal pump Ih single stage end suction centrifugal pump Air conditioning pump This pmp is a centrifugal end suction pump, it is now wildly used in industries like cooling, air conditioning, and aslo in resident, water supply. Is pump is especially for normal water. Ih pump is especially for chemicals. It has the function of pumping corrosive liquids. Is pump can pump water bellow 80 dgree centigree, if you want to pump water with high tempreature, we recommend you choose ir, which is same to is in structure and outlook, but is has good function of pumping water with temperater reaching 150degree centigree. For ih pump, it can pump liquids with temperature reaching 120 degree centigree. Also, if you want to pump oil in this size, please choose iry type which can reach 350 degree centigree. Capacity: 6 - 200m3/h, head: 5 to 150 meters. (special demand can be negotiated) Standard export wood case packing
HF Series is an single stage end- suction horizontal chemical centrifugal pump. it is in accordance with international standards ISO2858 and non-metallic Horizontal type pump technology combined with design and manufacturing. Pump body metal shell processing dovetail groove lined with FEP (F46), pump cover, impeller and the sleeve are embedded pieces of metal sintering suppression of the overall outsourcing of fluorine plastic. There are made of HT200 cast iron lining with Teflon PTFE / PEP(F46)/ PFA , impeller made by WCB wrapped by PTFE / PEP(F46)/ PFA, which grantee this type centrifugal pump could widely used in corrosive application and wear well. Mechanical seal is outside seal, stationary seal is alumina ceramic ( 99.9%)(or silicon nitride ,silicon carbide) , rotating seal is PTFE filling material or according to customer request. It is also can be made cartridge type mechanical seal. Advantage: High corrosive, well leak-proof, easy assembly and maintenance. Application Field : Acid pickling process Painting process Textile ,Dyes industry, etc Pharmacy & Pesticides Electroplating industry Chlorine water and waste water treatment Petroleum & Pharmaceutical Industry Chemical Industry Adding acid process Non-ferrous metals smelting of electrolyte transport Electricity Power Liquid Solution : Acid, alkali Salt solution Strong oxidant Organic solvents Corrosive slurries, solvents Hydrocarbons and other strong corrosive medium Ammonia water ion film caustic soda Waste water
General Type GSX series product is characterized by broad comprehensive performance curve,sound hydraulic performance, novel structure,high efficiency,high reliability,low net positive suction head ,and low maintenance. The design,manufacture,and quality of this series product meet the standard of GB/T5656 Technical conditions for centrifugal pumps-Class II and its efficiency indexes meet the standard of GB/T19762 The minimum allowable values of energy efficiency and evaluating values of energy conservation of centrifugal pump for fresh water Application GSX series products are mainly used for transport fresh water or other liquid with similar physicochemical properties to fresh water,it can also be widely applied in water supply and drainage system or circulation cooling water system for steel,petrochemical,thermal power generation,mining,and other working conditions Performance range Capacity 95~9000m3/h  Head 6~205m Temperature 80 cooling structure will be adopted for bearing, the material of casing & cover is QT500-7 150  Speed 740~2970r/min  Inlet diameter 125~900mm  Outlet diameter 80~900mm Structural feature 1.Sealing Superior mechanical seal,long term operation without leakage Mechanical seal,strong interchangeability for universal use by non-asbestos soft packing structure and injection type packing structure Stainless steel shaft sleeve for easy maintenance Half packing gland,large space for packing replacement 2.Protective cover Half-split structure,comply with IE standard,safe and reliable � 3.Casing Circular pressure chamber design with high efficiency Double-volute pumping chamber is with balanced radial force and sound strength; bearing and seal are with small force withstanding and long service life Water suction chamber is with split rib design;inlet is without vortex and noise while with stable operation and sound cavitation performance The inlet and outlet water channels are coated with smooth wear-resistant coating,and water loss is small Auto-correct pump cover for easy installation Inlet DN 500 for universal use by vertical and horizontal types 4.Bearing Short span and enlarged diameter design, stable operation and long service life. Grease lubrication with small and medium pump,online refueling Provided with online vibration and temperature measuring devices to ensure safety operation Transfer high temperature liquid,employ water-cooling structure 5.Shaft Bold design,universal use for 50HZ and 60HZ pump shaft,sound rigidity, and stable operation Full sealing design, no contact with liquid, and easy maintenance Allow short-time inversion, common shaft for forward and reverse rotations
Vertical slurry pumps are no submerged bearings or seals cantilevered pumps, which ideal for a variety of submerged suction pumping applications. These pumps operate well in a variety of sump conditions, and can also be readily applied on floating dewatering or other floating pump platforms.
High-Pressure ISW Series Pipe Centrifugal Water Pump Product Features: This product is of horizontal structure, used for conveying clean water and other liquid with similar physical, and chemical properties to clean water. It is suitable for industrial and urban water supply and drainage, pressurized water delivery in high-rise buildings, sprinkler irrigation in gardens, pressurized fire fighting, long-distance transportation, heating ventilation air conditioning circulation, bathroom, and other pressurized cooling, and heating water circulation and supporting equipment. ISW series single stage end suction centrifugal pump is an energy-saving pump. The advantage is hydraulic capability is distributed reasonably, wide option for user, conveniently check and repair, the efficiency and throw is up to advanced international level. This pump is suiable for industrial and city water supply, water drainage.
Design Features: Horizontal Centrifugal, Back-Pull-Out type pump fitted with single stage closed Impeller in foot mounted Volute Casing having axial end suction and Vertical centerline delivery. Applications: To handle Hydrocarbons, Volatile Liquids, Thermic Fluids and Corrosives in Chemical / Petrochemical / Fertilizer / Sugar / Paper and other Process Industries. Custom-built Design: Pumps with different material of construction can be offered on request.
Wholesale High Performance Eifel Brand Name Pipeline Pumps Product Description Pump type: EA series stainless steel single stage end suction centrifugal pump Design Standard: European standard BS EN733/DIN24255 Structure: Horizontal,Axial End-Suction,Single-Stage,Volute Casing,Back pull-out Discharge Size: DN32~300mm Flange: DIN2501 PN16 GB/T17241.6 PN1.6 Casing: ASTM304/ASTM316 Impeller: ASTM304/ASTM316 Shaft: ASTM420 standard,ASTM304/ASTM316/ASTM1045 options on request Shaft Seal: Mechanical Seal standard,Gland Packing options on request Flow Rate(Q): 4~1584m3/h Head(H): 2~150m Speed: 1450/2900rpm(50Hz);1750/3500 rpm(60Hz) Max Temperature: 85�°C(standard);105�°C(option on request) Working Pressure: 1.0MPa(standard);1.6MPa(option on request) Conveying Medium: water/liquid Advantage: Interchangeable parts,high-effective,high performance,voice-saving,easily installed and maintained Applications : Food and chemical industry,water supply and drainage,HVAC and Cooling Tower,marine-ballasting&bilge,booster and pressurization set,irrigation and agriculture,fire-fighting system,plants,mines,air-condition systems,etc.
Fzb series fluorine plastic linning self-priming pump Patent product, base on ihf centrifugal pump structure, installed the double volute self-priming pump casing on ihf pump, simple structure and for widely usage. Corrosion and pressure resistance, wet parts are made of corrosion resistant fluoroplastic, with these advantages, fzb pumps available to high corrosive applications. Pump base plate is made of metal; make the pump available to high pressure resistance applications. Easy for operating Developed for low sump application, pump installed above the sump or tank, which easy for operating, maintenance and repair. Min model no 25fzb 18l pumping flow capacity 3.6 m3/h, 18 meter pump head , equipped with motor power 2.2kw Max model no 100fzb 30l pumping flow capacity 100 m3/h , 30 meter pump head, equipped with motor power 18.5kw Model no 50fzb -30l 50 pump inlet diameter are 50mm Fzb single stage end-suction centrifugal pump 30 pump head 30 meter L pump connection by coupling Pump flow capacity 12 m3/h Motor 4kw Self-priming height 3 meter . Medium Acids & lyes Waste water Chlorine water Electrolyte Application Chemical industry Pesticide Acid and alkali making Papermaking Acid pickle process Electronics industry
End Suction Centrifugal Pumps
INSTALLATIONS AND USE .For pumping clean liquids without abrasive particles, which are chemically non aggressive to the pump materials .For water supply .For heating, air- conditioning, cooling and circulation plants .For civil and industrial applications .For firefighting applications .For...
Cassia is an aromatic bark, similar to cinnamon, but differing in strength and quality. Its bark is darker, thicker and coarser, and the corky outer bark is often left on. The outer surface is rough and grayish brown, the inside barks is smoother and reddish-brown. It is less costly than cinnamon and is often sold ground as cinnamon. When buying as sticks, cinnamon rolls into a single quill while cassia is rolled from both sides toward the centre so that they end up resembling scrolls. Cassia buds. Cassia buds resemble cloves. They are the dried unripe fruits about 14 mm (1/2 in) long and half as wide. It is native to Burma and grown in China, Indo-China, the East and West Indies and Central America. One of the oldest spices known to man. It has a strong characteristic aroma and flavor. We may sometimes hear cinnamon refer to as cassia. This term is used to distinguish between the Southeast Asia and the Ceylon type of cinnamon. Almost all of the cinnamon consumed in the United States is derived from trees grown in Southeast Asia. Nowadays cinnamon is used to flavor bakery and dairy products, as well as drinks. Cassia-cinnamon is such a familiar and beloved spice it needs little introduction. A global favorite for its delicious aromatic flavor.
Marigolds were first discovered by the Portuguese in Central America in the 16th century. Marigolds are hardy, annual plants and are great plants for cheering up any garden. Broadly, there are two genuses which are referred to by the common name, Marigolds viz., Tagetes and Celandula. Tagetes includes African Marigolds and French Marigolds. Celandula includes Pot Marigolds. Kingdom : Plantae Division : Magnoliophyta Class : Magnoliopsida Order : Asterales Family : Asteraceae Genus : Tagetes, Calendula Marigolds come in different colors, yellow and orange being the most common. Most of the marigolds have strong, pungent odor and have has great value in cosmetic treatment. There are many varieties of Marigolds available today. Some of the major Marigold varieties are listed below: African or American Marigolds (Tagetes erecta): These marigolds are tall, erect-growing plants up to three feet in height. The flowers are globe-shaped and large. Flowers may measure up to 5 inches across. African Marigolds are very good bedding plants. These flowers are yellow to orange and do not include red colored Marigolds. The Africans take longer to reach flowering stage than the French type. French Marigolds (Tagetes patula): Marigold cultivars in this group grow 5 inches to 18 inches high. Flower colors are red, orange and yellow. Red and orange bicolor patterns are also found. Flowers are smaller, (2 inches across). French Marigolds are ideal for edging flowerbeds and in mass plantings. They also do well in containers and window boxes. Signet Marigolds (T. signata 'pumila'): The signet Marigolds produce compact plants with finely divided, lacy foliage and clusters of small, single flowers. They have yellow to orange colored, edible flowers.The flowers of signet marigolds have a spicy tarragon flavor. The foliage has a pleasant lemon fragrance. Signet Marigolds are excellent plants for edging beds and in window boxes. Mule Marigolds: These marigolds are the sterile hybrids of tall African and dwarf French marigolds, hence known as mule Marigolds. Most triploid cultivars grow from 12 to 18 inches high. Though they have the combined qualities of their parents, their rate of germination is low. Marigold (Calendula) is an extremely effective herb for the treatment of skin problems and can be used wherever there is inflammation of the skin, whether due to infection or physical damage; for example, crural ulceration, varicose veins, haemorrhoids, anal fissures, mastitis, sebaceous cysts, impetigo or other inflamed cutaneous lesions. As an ointment, Marigold (Calendula) is an excellent cosmetic remedy for repairing minor damage to the skin such as subdermal broken capillaries or sunburn. The sap from the stem is reputed to remove warts, corns and calluses.
double tube hand pump for BIG SUP board TRIPLE ACTION it's more compact and light. It's the best for brands who want to use a pump of triple action as standard equipment in their SUP. The compact piston permits also females and young guys to be able to achieve easily high pressure. HP6, being used in TRIPLE-doublesingle action, can achieve 30psi rapidly and effortlessly. The switching 3-2-1 can be realized easily and comfortably rotating the switch knob. Itâ??s completely customizable for colour, graphic and calibration of gauge meter. Features: · capacity 3.2+3.2L, max. pressure 30psi as DIN EN 16051 · switch knob to change comfortably from triple to double or single seals and anti-sand filter for long life of pump and SUP extra long body and high-airflow piston for an easier inflation pump completely shock-proof, compact and light (1.7kg) · shockproof gauge meter
Centrifugal Pump VOLUTE ECD Series can be used for the following services in commercial, residential, agriculture industrial processing petroleum, food & beverage industries.
Overview Type NDX pump is applicable for pumping clean water and liquids whose physical and chemical properties are similar to water and without solid particles. This series of products can be used in factories,mines,urban water supply and drainage,HAVC,industrial softened water and farmland irrigation and drainage,etc.It can also be used in pressure stabilization and water supply systems of urban fire control. Pump with the same specification can change the performance parameters by cutting the outer diameter of the impeller;the normal speed of the pump is 1450RPM and 2900RPM, if it is required to operate at the maximum speed of 3550RPM(60Hz power supply or with gasoline and diesel engine),our company can provide technical instruction on the change of the outer diameter of the impeller The type NDX pump features simple structure,reliable performance,small volume,light weight,high efficiency,good ati-cavitation performance, low power consumption and convenient use and maintenance The pump is suitable for pumping medium at temperature of -10~85 and working pressure of 1.0MPa,if there is a need to increase to 1.6MPa or higher,please specify when selecting and ordering Performance  Capacity: 5-1650m3/h  Head: 5-135 m Product Features Energy efficient: Applying the most advanced NRCE design software and CFD fluid simulation software to develop and design the high efficiency hydraulic model,through the analysis of pump flow field,temperature field and strength,thermal deformation,fracture,rotor dynamics,etc,to achieve high efficiency ,reliability and wide efficiency zone,we have made the pump satisfy the efficiency and reliability requirements of centrifugal pump operating under design conditions and non-design conditions, reaching the international advanced level. Rear opening type structure:The maintenance is convenient,It is not necessary to disassemble the suction and discharge pipes during maintenance to pull out the rotor parts for maintenance Quality assurance:Before casting,the imported chemical analysis of the materials was carried out by the direct reading spectrum analyzer introduced from Britain to ensure that the material composition meets the requirement.The pump impeller and rotor components are tested by precise dynamic balance test,so the pump can run more smoothly, have less vibration and noise and longer service life. Product orientation:Improve the technical level of the domestic equipment industry, effectively serve equipment and processes to meet the needs of safety,reliability,energy conservation and environmental Protection.
Os series single-stage double-suction split volute centrifugal pump Os axially split pump overview: Model os pumps are single-stage double-suction inter opened spiral casing centrifugal pumps.It is used to water transportation in water plants, air conditioning water circulation, building water supply, irrigation, drainage pump station, electric power station, industrial water supply system, fire-fighting system, and shipbuilding and so on. Os axially split pump material: Pump casing:casting pig, ductalloy, cast steel; Impeller: bronze, casting pig, silicon brass, stainless steel; Shaft: stainless steel, carbon steel; Seal-ring on pump casing:bronze, casting pig, silicon brass, stainless steel. Os axially split pump feature: 1. It has compact structure, nice appearance, good stability and it is easy to install; 2. The optimally designed and stable running double-suction impeller makes the axial force reduced to the minimum and it has a blade-style of excellent hydraulic performance. Both internal surface of the of the pump casing and the impeller's surface are extremely smooth after being precisely cast.They have a notable performance on ovapour-corrosion resisting and a high efficiency. 3.Bearing use skf and nsf bearings to guarantee a stable running, low noise ande long duration. 4.Shaft seal use burgmann mechanical or stuffing seal to ensure a 8000h non-leak running. 5.Installation does not need to adjust when assembly and it can be vertically or horizontally assembled upon the conditions of use on the spot.
S/SH series is suitable for transporting pure water or other liquids of both physical and chemical natures similar to pure water. It is applicable to transport medium with temperature of not higher than 80â?? , and high temperature boiler water or transporting medium similar to hot water. If The TDG pumps add a cooling system with specfice shaft seal and materials, It can be used to transport boiler water, hot water, oil, chemicals or corrosive liquids with the temperature of not higher than 130.
During last decade Guar has immerged as an important industrial raw material and Produced by man for thousands of years. India has been the single largest producer and exporter of Guar gum accounting for more than 80 percent of the global output and trade. Guar has now assumed a larger role among the domesticated plants due to its unique functional properties. India Ranks First in the production of guar which is grown in the North Western part of the Country which mainly includes the states of Rajasthan, Gujarat, Haryana and Punjab. Other main countries are Pakistan, U.S.A and Brazil The by-product of Guar Gum industry consisting of the outer seed coat and germ material is called guar meal. The Guar meal after gum Extraction is a potential source of protein and contains about 42% crude protein which is one and a half times more than the level of protein in guar seed. The protein content in guar meal is well comparable with that of oil cakes. It is used as a feed for livestock including poultry. Guar meal contains two deleterious factors i.e. residual guar gum and trypsin inhibitor, Toasting of Guar Gum improves its nutritive value in chicks. Toasted guar Meal can be used in limited quantity i.e. Up to 10% in Poultry diet. However it can replace groundnut cake by almost 100% in animal feeds. Guar Gum (Galactomanan) is a high molecular weight carbohydrate polymer made up of a large number of mannose and galactose unit linked together. The crude Guar Gum is a greyish white powder 90% of which dissolves in water. It is non ionic polysaccharide based on the milled endosperm of the guar bean whose average. Composition is: Hydrocolloid: 23% Fats: 40% Proteins: 34% The most important property of the Guar is its ability to hydrate rapidly in cold water to attain a very high viscosity at relatively low concentrations. Its specific colloidal nature gives the solution an excellent thickening power which is 6 to10 times thicker than that obtained from starch. It is stable over a wide range of PH and it also improves the flow ability and pump ability of the fluid. It is a superior friction loss reducing agent.
